![Michael Buesch](/assets/img/avatar_default.png)
This adds a simple firmware watchdog for the opensource firmware. This will check every 15 seconds, if the firmware zeroed out the watchdog register. The firmware will do this in its eventloop. Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
979 lines
34 KiB
C
979 lines
34 KiB
C
#ifndef B43_H_
|
|
#define B43_H_
|
|
|
|
#include <linux/kernel.h>
|
|
#include <linux/spinlock.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/hw_random.h>
|
|
#include <linux/ssb/ssb.h>
|
|
#include <net/mac80211.h>
|
|
|
|
#include "debugfs.h"
|
|
#include "leds.h"
|
|
#include "rfkill.h"
|
|
#include "lo.h"
|
|
#include "phy.h"
|
|
|
|
|
|
/* The unique identifier of the firmware that's officially supported by
|
|
* this driver version. */
|
|
#define B43_SUPPORTED_FIRMWARE_ID "FW13"
|
|
|
|
|
|
#ifdef CONFIG_B43_DEBUG
|
|
# define B43_DEBUG 1
|
|
#else
|
|
# define B43_DEBUG 0
|
|
#endif
|
|
|
|
#define B43_RX_MAX_SSI 60
|
|
|
|
/* MMIO offsets */
|
|
#define B43_MMIO_DMA0_REASON 0x20
|
|
#define B43_MMIO_DMA0_IRQ_MASK 0x24
|
|
#define B43_MMIO_DMA1_REASON 0x28
|
|
#define B43_MMIO_DMA1_IRQ_MASK 0x2C
|
|
#define B43_MMIO_DMA2_REASON 0x30
|
|
#define B43_MMIO_DMA2_IRQ_MASK 0x34
|
|
#define B43_MMIO_DMA3_REASON 0x38
|
|
#define B43_MMIO_DMA3_IRQ_MASK 0x3C
|
|
#define B43_MMIO_DMA4_REASON 0x40
|
|
#define B43_MMIO_DMA4_IRQ_MASK 0x44
|
|
#define B43_MMIO_DMA5_REASON 0x48
|
|
#define B43_MMIO_DMA5_IRQ_MASK 0x4C
|
|
#define B43_MMIO_MACCTL 0x120 /* MAC control */
|
|
#define B43_MMIO_MACCMD 0x124 /* MAC command */
|
|
#define B43_MMIO_GEN_IRQ_REASON 0x128
|
|
#define B43_MMIO_GEN_IRQ_MASK 0x12C
|
|
#define B43_MMIO_RAM_CONTROL 0x130
|
|
#define B43_MMIO_RAM_DATA 0x134
|
|
#define B43_MMIO_PS_STATUS 0x140
|
|
#define B43_MMIO_RADIO_HWENABLED_HI 0x158
|
|
#define B43_MMIO_SHM_CONTROL 0x160
|
|
#define B43_MMIO_SHM_DATA 0x164
|
|
#define B43_MMIO_SHM_DATA_UNALIGNED 0x166
|
|
#define B43_MMIO_XMITSTAT_0 0x170
|
|
#define B43_MMIO_XMITSTAT_1 0x174
|
|
#define B43_MMIO_REV3PLUS_TSF_LOW 0x180 /* core rev >= 3 only */
|
|
#define B43_MMIO_REV3PLUS_TSF_HIGH 0x184 /* core rev >= 3 only */
|
|
#define B43_MMIO_TSF_CFP_REP 0x188
|
|
#define B43_MMIO_TSF_CFP_START 0x18C
|
|
#define B43_MMIO_TSF_CFP_MAXDUR 0x190
|
|
|
|
/* 32-bit DMA */
|
|
#define B43_MMIO_DMA32_BASE0 0x200
|
|
#define B43_MMIO_DMA32_BASE1 0x220
|
|
#define B43_MMIO_DMA32_BASE2 0x240
|
|
#define B43_MMIO_DMA32_BASE3 0x260
|
|
#define B43_MMIO_DMA32_BASE4 0x280
|
|
#define B43_MMIO_DMA32_BASE5 0x2A0
|
|
/* 64-bit DMA */
|
|
#define B43_MMIO_DMA64_BASE0 0x200
|
|
#define B43_MMIO_DMA64_BASE1 0x240
|
|
#define B43_MMIO_DMA64_BASE2 0x280
|
|
#define B43_MMIO_DMA64_BASE3 0x2C0
|
|
#define B43_MMIO_DMA64_BASE4 0x300
|
|
#define B43_MMIO_DMA64_BASE5 0x340
|
|
|
|
/* PIO on core rev < 11 */
|
|
#define B43_MMIO_PIO_BASE0 0x300
|
|
#define B43_MMIO_PIO_BASE1 0x310
|
|
#define B43_MMIO_PIO_BASE2 0x320
|
|
#define B43_MMIO_PIO_BASE3 0x330
|
|
#define B43_MMIO_PIO_BASE4 0x340
|
|
#define B43_MMIO_PIO_BASE5 0x350
|
|
#define B43_MMIO_PIO_BASE6 0x360
|
|
#define B43_MMIO_PIO_BASE7 0x370
|
|
/* PIO on core rev >= 11 */
|
|
#define B43_MMIO_PIO11_BASE0 0x200
|
|
#define B43_MMIO_PIO11_BASE1 0x240
|
|
#define B43_MMIO_PIO11_BASE2 0x280
|
|
#define B43_MMIO_PIO11_BASE3 0x2C0
|
|
#define B43_MMIO_PIO11_BASE4 0x300
|
|
#define B43_MMIO_PIO11_BASE5 0x340
|
|
|
|
#define B43_MMIO_PHY_VER 0x3E0
|
|
#define B43_MMIO_PHY_RADIO 0x3E2
|
|
#define B43_MMIO_PHY0 0x3E6
|
|
#define B43_MMIO_ANTENNA 0x3E8
|
|
#define B43_MMIO_CHANNEL 0x3F0
|
|
#define B43_MMIO_CHANNEL_EXT 0x3F4
|
|
#define B43_MMIO_RADIO_CONTROL 0x3F6
|
|
#define B43_MMIO_RADIO_DATA_HIGH 0x3F8
|
|
#define B43_MMIO_RADIO_DATA_LOW 0x3FA
|
|
#define B43_MMIO_PHY_CONTROL 0x3FC
|
|
#define B43_MMIO_PHY_DATA 0x3FE
|
|
#define B43_MMIO_MACFILTER_CONTROL 0x420
|
|
#define B43_MMIO_MACFILTER_DATA 0x422
|
|
#define B43_MMIO_RCMTA_COUNT 0x43C
|
|
#define B43_MMIO_RADIO_HWENABLED_LO 0x49A
|
|
#define B43_MMIO_GPIO_CONTROL 0x49C
|
|
#define B43_MMIO_GPIO_MASK 0x49E
|
|
#define B43_MMIO_TSF_CFP_START_LOW 0x604
|
|
#define B43_MMIO_TSF_CFP_START_HIGH 0x606
|
|
#define B43_MMIO_TSF_CFP_PRETBTT 0x612
|
|
#define B43_MMIO_TSF_0 0x632 /* core rev < 3 only */
|
|
#define B43_MMIO_TSF_1 0x634 /* core rev < 3 only */
|
|
#define B43_MMIO_TSF_2 0x636 /* core rev < 3 only */
|
|
#define B43_MMIO_TSF_3 0x638 /* core rev < 3 only */
|
|
#define B43_MMIO_RNG 0x65A
|
|
#define B43_MMIO_IFSCTL 0x688 /* Interframe space control */
|
|
#define B43_MMIO_IFSCTL_USE_EDCF 0x0004
|
|
#define B43_MMIO_POWERUP_DELAY 0x6A8
|
|
|
|
/* SPROM boardflags_lo values */
|
|
#define B43_BFL_BTCOEXIST 0x0001 /* implements Bluetooth coexistance */
|
|
#define B43_BFL_PACTRL 0x0002 /* GPIO 9 controlling the PA */
|
|
#define B43_BFL_AIRLINEMODE 0x0004 /* implements GPIO 13 radio disable indication */
|
|
#define B43_BFL_RSSI 0x0008 /* software calculates nrssi slope. */
|
|
#define B43_BFL_ENETSPI 0x0010 /* has ephy roboswitch spi */
|
|
#define B43_BFL_XTAL_NOSLOW 0x0020 /* no slow clock available */
|
|
#define B43_BFL_CCKHIPWR 0x0040 /* can do high power CCK transmission */
|
|
#define B43_BFL_ENETADM 0x0080 /* has ADMtek switch */
|
|
#define B43_BFL_ENETVLAN 0x0100 /* can do vlan */
|
|
#define B43_BFL_AFTERBURNER 0x0200 /* supports Afterburner mode */
|
|
#define B43_BFL_NOPCI 0x0400 /* leaves PCI floating */
|
|
#define B43_BFL_FEM 0x0800 /* supports the Front End Module */
|
|
#define B43_BFL_EXTLNA 0x1000 /* has an external LNA */
|
|
#define B43_BFL_HGPA 0x2000 /* had high gain PA */
|
|
#define B43_BFL_BTCMOD 0x4000 /* BFL_BTCOEXIST is given in alternate GPIOs */
|
|
#define B43_BFL_ALTIQ 0x8000 /* alternate I/Q settings */
|
|
|
|
/* GPIO register offset, in both ChipCommon and PCI core. */
|
|
#define B43_GPIO_CONTROL 0x6c
|
|
|
|
/* SHM Routing */
|
|
enum {
|
|
B43_SHM_UCODE, /* Microcode memory */
|
|
B43_SHM_SHARED, /* Shared memory */
|
|
B43_SHM_SCRATCH, /* Scratch memory */
|
|
B43_SHM_HW, /* Internal hardware register */
|
|
B43_SHM_RCMTA, /* Receive match transmitter address (rev >= 5 only) */
|
|
};
|
|
/* SHM Routing modifiers */
|
|
#define B43_SHM_AUTOINC_R 0x0200 /* Auto-increment address on read */
|
|
#define B43_SHM_AUTOINC_W 0x0100 /* Auto-increment address on write */
|
|
#define B43_SHM_AUTOINC_RW (B43_SHM_AUTOINC_R | \
|
|
B43_SHM_AUTOINC_W)
|
|
|
|
/* Misc SHM_SHARED offsets */
|
|
#define B43_SHM_SH_WLCOREREV 0x0016 /* 802.11 core revision */
|
|
#define B43_SHM_SH_PCTLWDPOS 0x0008
|
|
#define B43_SHM_SH_RXPADOFF 0x0034 /* RX Padding data offset (PIO only) */
|
|
#define B43_SHM_SH_PHYVER 0x0050 /* PHY version */
|
|
#define B43_SHM_SH_PHYTYPE 0x0052 /* PHY type */
|
|
#define B43_SHM_SH_ANTSWAP 0x005C /* Antenna swap threshold */
|
|
#define B43_SHM_SH_HOSTFLO 0x005E /* Hostflags for ucode options (low) */
|
|
#define B43_SHM_SH_HOSTFMI 0x0060 /* Hostflags for ucode options (middle) */
|
|
#define B43_SHM_SH_HOSTFHI 0x0062 /* Hostflags for ucode options (high) */
|
|
#define B43_SHM_SH_RFATT 0x0064 /* Current radio attenuation value */
|
|
#define B43_SHM_SH_RADAR 0x0066 /* Radar register */
|
|
#define B43_SHM_SH_PHYTXNOI 0x006E /* PHY noise directly after TX (lower 8bit only) */
|
|
#define B43_SHM_SH_RFRXSP1 0x0072 /* RF RX SP Register 1 */
|
|
#define B43_SHM_SH_CHAN 0x00A0 /* Current channel (low 8bit only) */
|
|
#define B43_SHM_SH_CHAN_5GHZ 0x0100 /* Bit set, if 5Ghz channel */
|
|
#define B43_SHM_SH_BCMCFIFOID 0x0108 /* Last posted cookie to the bcast/mcast FIFO */
|
|
/* SHM_SHARED TX FIFO variables */
|
|
#define B43_SHM_SH_SIZE01 0x0098 /* TX FIFO size for FIFO 0 (low) and 1 (high) */
|
|
#define B43_SHM_SH_SIZE23 0x009A /* TX FIFO size for FIFO 2 and 3 */
|
|
#define B43_SHM_SH_SIZE45 0x009C /* TX FIFO size for FIFO 4 and 5 */
|
|
#define B43_SHM_SH_SIZE67 0x009E /* TX FIFO size for FIFO 6 and 7 */
|
|
/* SHM_SHARED background noise */
|
|
#define B43_SHM_SH_JSSI0 0x0088 /* Measure JSSI 0 */
|
|
#define B43_SHM_SH_JSSI1 0x008A /* Measure JSSI 1 */
|
|
#define B43_SHM_SH_JSSIAUX 0x008C /* Measure JSSI AUX */
|
|
/* SHM_SHARED crypto engine */
|
|
#define B43_SHM_SH_DEFAULTIV 0x003C /* Default IV location */
|
|
#define B43_SHM_SH_NRRXTRANS 0x003E /* # of soft RX transmitter addresses (max 8) */
|
|
#define B43_SHM_SH_KTP 0x0056 /* Key table pointer */
|
|
#define B43_SHM_SH_TKIPTSCTTAK 0x0318
|
|
#define B43_SHM_SH_KEYIDXBLOCK 0x05D4 /* Key index/algorithm block (v4 firmware) */
|
|
#define B43_SHM_SH_PSM 0x05F4 /* PSM transmitter address match block (rev < 5) */
|
|
/* SHM_SHARED WME variables */
|
|
#define B43_SHM_SH_EDCFSTAT 0x000E /* EDCF status */
|
|
#define B43_SHM_SH_TXFCUR 0x0030 /* TXF current index */
|
|
#define B43_SHM_SH_EDCFQ 0x0240 /* EDCF Q info */
|
|
/* SHM_SHARED powersave mode related */
|
|
#define B43_SHM_SH_SLOTT 0x0010 /* Slot time */
|
|
#define B43_SHM_SH_DTIMPER 0x0012 /* DTIM period */
|
|
#define B43_SHM_SH_NOSLPZNATDTIM 0x004C /* NOSLPZNAT DTIM */
|
|
/* SHM_SHARED beacon/AP variables */
|
|
#define B43_SHM_SH_BTL0 0x0018 /* Beacon template length 0 */
|
|
#define B43_SHM_SH_BTL1 0x001A /* Beacon template length 1 */
|
|
#define B43_SHM_SH_BTSFOFF 0x001C /* Beacon TSF offset */
|
|
#define B43_SHM_SH_TIMBPOS 0x001E /* TIM B position in beacon */
|
|
#define B43_SHM_SH_DTIMP 0x0012 /* DTIP period */
|
|
#define B43_SHM_SH_MCASTCOOKIE 0x00A8 /* Last bcast/mcast frame ID */
|
|
#define B43_SHM_SH_SFFBLIM 0x0044 /* Short frame fallback retry limit */
|
|
#define B43_SHM_SH_LFFBLIM 0x0046 /* Long frame fallback retry limit */
|
|
#define B43_SHM_SH_BEACPHYCTL 0x0054 /* Beacon PHY TX control word (see PHY TX control) */
|
|
#define B43_SHM_SH_EXTNPHYCTL 0x00B0 /* Extended bytes for beacon PHY control (N) */
|
|
/* SHM_SHARED ACK/CTS control */
|
|
#define B43_SHM_SH_ACKCTSPHYCTL 0x0022 /* ACK/CTS PHY control word (see PHY TX control) */
|
|
/* SHM_SHARED probe response variables */
|
|
#define B43_SHM_SH_PRSSID 0x0160 /* Probe Response SSID */
|
|
#define B43_SHM_SH_PRSSIDLEN 0x0048 /* Probe Response SSID length */
|
|
#define B43_SHM_SH_PRTLEN 0x004A /* Probe Response template length */
|
|
#define B43_SHM_SH_PRMAXTIME 0x0074 /* Probe Response max time */
|
|
#define B43_SHM_SH_PRPHYCTL 0x0188 /* Probe Response PHY TX control word */
|
|
/* SHM_SHARED rate tables */
|
|
#define B43_SHM_SH_OFDMDIRECT 0x01C0 /* Pointer to OFDM direct map */
|
|
#define B43_SHM_SH_OFDMBASIC 0x01E0 /* Pointer to OFDM basic rate map */
|
|
#define B43_SHM_SH_CCKDIRECT 0x0200 /* Pointer to CCK direct map */
|
|
#define B43_SHM_SH_CCKBASIC 0x0220 /* Pointer to CCK basic rate map */
|
|
/* SHM_SHARED microcode soft registers */
|
|
#define B43_SHM_SH_UCODEREV 0x0000 /* Microcode revision */
|
|
#define B43_SHM_SH_UCODEPATCH 0x0002 /* Microcode patchlevel */
|
|
#define B43_SHM_SH_UCODEDATE 0x0004 /* Microcode date */
|
|
#define B43_SHM_SH_UCODETIME 0x0006 /* Microcode time */
|
|
#define B43_SHM_SH_UCODESTAT 0x0040 /* Microcode debug status code */
|
|
#define B43_SHM_SH_UCODESTAT_INVALID 0
|
|
#define B43_SHM_SH_UCODESTAT_INIT 1
|
|
#define B43_SHM_SH_UCODESTAT_ACTIVE 2
|
|
#define B43_SHM_SH_UCODESTAT_SUSP 3 /* suspended */
|
|
#define B43_SHM_SH_UCODESTAT_SLEEP 4 /* asleep (PS) */
|
|
#define B43_SHM_SH_MAXBFRAMES 0x0080 /* Maximum number of frames in a burst */
|
|
#define B43_SHM_SH_SPUWKUP 0x0094 /* pre-wakeup for synth PU in us */
|
|
#define B43_SHM_SH_PRETBTT 0x0096 /* pre-TBTT in us */
|
|
|
|
/* SHM_SCRATCH offsets */
|
|
#define B43_SHM_SC_MINCONT 0x0003 /* Minimum contention window */
|
|
#define B43_SHM_SC_MAXCONT 0x0004 /* Maximum contention window */
|
|
#define B43_SHM_SC_CURCONT 0x0005 /* Current contention window */
|
|
#define B43_SHM_SC_SRLIMIT 0x0006 /* Short retry count limit */
|
|
#define B43_SHM_SC_LRLIMIT 0x0007 /* Long retry count limit */
|
|
#define B43_SHM_SC_DTIMC 0x0008 /* Current DTIM count */
|
|
#define B43_SHM_SC_BTL0LEN 0x0015 /* Beacon 0 template length */
|
|
#define B43_SHM_SC_BTL1LEN 0x0016 /* Beacon 1 template length */
|
|
#define B43_SHM_SC_SCFB 0x0017 /* Short frame transmit count threshold for rate fallback */
|
|
#define B43_SHM_SC_LCFB 0x0018 /* Long frame transmit count threshold for rate fallback */
|
|
|
|
/* Hardware Radio Enable masks */
|
|
#define B43_MMIO_RADIO_HWENABLED_HI_MASK (1 << 16)
|
|
#define B43_MMIO_RADIO_HWENABLED_LO_MASK (1 << 4)
|
|
|
|
/* HostFlags. See b43_hf_read/write() */
|
|
#define B43_HF_ANTDIVHELP 0x000000000001ULL /* ucode antenna div helper */
|
|
#define B43_HF_SYMW 0x000000000002ULL /* G-PHY SYM workaround */
|
|
#define B43_HF_RXPULLW 0x000000000004ULL /* RX pullup workaround */
|
|
#define B43_HF_CCKBOOST 0x000000000008ULL /* 4dB CCK power boost (exclusive with OFDM boost) */
|
|
#define B43_HF_BTCOEX 0x000000000010ULL /* Bluetooth coexistance */
|
|
#define B43_HF_GDCW 0x000000000020ULL /* G-PHY DC canceller filter bw workaround */
|
|
#define B43_HF_OFDMPABOOST 0x000000000040ULL /* Enable PA gain boost for OFDM */
|
|
#define B43_HF_ACPR 0x000000000080ULL /* Disable for Japan, channel 14 */
|
|
#define B43_HF_EDCF 0x000000000100ULL /* on if WME and MAC suspended */
|
|
#define B43_HF_TSSIRPSMW 0x000000000200ULL /* TSSI reset PSM ucode workaround */
|
|
#define B43_HF_20IN40IQW 0x000000000200ULL /* 20 in 40 MHz I/Q workaround (rev >= 13 only) */
|
|
#define B43_HF_DSCRQ 0x000000000400ULL /* Disable slow clock request in ucode */
|
|
#define B43_HF_ACIW 0x000000000800ULL /* ACI workaround: shift bits by 2 on PHY CRS */
|
|
#define B43_HF_2060W 0x000000001000ULL /* 2060 radio workaround */
|
|
#define B43_HF_RADARW 0x000000002000ULL /* Radar workaround */
|
|
#define B43_HF_USEDEFKEYS 0x000000004000ULL /* Enable use of default keys */
|
|
#define B43_HF_AFTERBURNER 0x000000008000ULL /* Afterburner enabled */
|
|
#define B43_HF_BT4PRIOCOEX 0x000000010000ULL /* Bluetooth 4-priority coexistance */
|
|
#define B43_HF_FWKUP 0x000000020000ULL /* Fast wake-up ucode */
|
|
#define B43_HF_VCORECALC 0x000000040000ULL /* Force VCO recalculation when powering up synthpu */
|
|
#define B43_HF_PCISCW 0x000000080000ULL /* PCI slow clock workaround */
|
|
#define B43_HF_4318TSSI 0x000000200000ULL /* 4318 TSSI */
|
|
#define B43_HF_FBCMCFIFO 0x000000400000ULL /* Flush bcast/mcast FIFO immediately */
|
|
#define B43_HF_HWPCTL 0x000000800000ULL /* Enable hardwarre power control */
|
|
#define B43_HF_BTCOEXALT 0x000001000000ULL /* Bluetooth coexistance in alternate pins */
|
|
#define B43_HF_TXBTCHECK 0x000002000000ULL /* Bluetooth check during transmission */
|
|
#define B43_HF_SKCFPUP 0x000004000000ULL /* Skip CFP update */
|
|
#define B43_HF_N40W 0x000008000000ULL /* N PHY 40 MHz workaround (rev >= 13 only) */
|
|
#define B43_HF_ANTSEL 0x000020000000ULL /* Antenna selection (for testing antenna div.) */
|
|
#define B43_HF_BT3COEXT 0x000020000000ULL /* Bluetooth 3-wire coexistence (rev >= 13 only) */
|
|
#define B43_HF_BTCANT 0x000040000000ULL /* Bluetooth coexistence (antenna mode) (rev >= 13 only) */
|
|
#define B43_HF_ANTSELEN 0x000100000000ULL /* Antenna selection enabled (rev >= 13 only) */
|
|
#define B43_HF_ANTSELMODE 0x000200000000ULL /* Antenna selection mode (rev >= 13 only) */
|
|
#define B43_HF_MLADVW 0x001000000000ULL /* N PHY ML ADV workaround (rev >= 13 only) */
|
|
#define B43_HF_PR45960W 0x080000000000ULL /* PR 45960 workaround (rev >= 13 only) */
|
|
|
|
/* MacFilter offsets. */
|
|
#define B43_MACFILTER_SELF 0x0000
|
|
#define B43_MACFILTER_BSSID 0x0003
|
|
|
|
/* PowerControl */
|
|
#define B43_PCTL_IN 0xB0
|
|
#define B43_PCTL_OUT 0xB4
|
|
#define B43_PCTL_OUTENABLE 0xB8
|
|
#define B43_PCTL_XTAL_POWERUP 0x40
|
|
#define B43_PCTL_PLL_POWERDOWN 0x80
|
|
|
|
/* PowerControl Clock Modes */
|
|
#define B43_PCTL_CLK_FAST 0x00
|
|
#define B43_PCTL_CLK_SLOW 0x01
|
|
#define B43_PCTL_CLK_DYNAMIC 0x02
|
|
|
|
#define B43_PCTL_FORCE_SLOW 0x0800
|
|
#define B43_PCTL_FORCE_PLL 0x1000
|
|
#define B43_PCTL_DYN_XTAL 0x2000
|
|
|
|
/* PHYVersioning */
|
|
#define B43_PHYTYPE_A 0x00
|
|
#define B43_PHYTYPE_B 0x01
|
|
#define B43_PHYTYPE_G 0x02
|
|
#define B43_PHYTYPE_N 0x04
|
|
#define B43_PHYTYPE_LP 0x05
|
|
|
|
/* PHYRegisters */
|
|
#define B43_PHY_ILT_A_CTRL 0x0072
|
|
#define B43_PHY_ILT_A_DATA1 0x0073
|
|
#define B43_PHY_ILT_A_DATA2 0x0074
|
|
#define B43_PHY_G_LO_CONTROL 0x0810
|
|
#define B43_PHY_ILT_G_CTRL 0x0472
|
|
#define B43_PHY_ILT_G_DATA1 0x0473
|
|
#define B43_PHY_ILT_G_DATA2 0x0474
|
|
#define B43_PHY_A_PCTL 0x007B
|
|
#define B43_PHY_G_PCTL 0x0029
|
|
#define B43_PHY_A_CRS 0x0029
|
|
#define B43_PHY_RADIO_BITFIELD 0x0401
|
|
#define B43_PHY_G_CRS 0x0429
|
|
#define B43_PHY_NRSSILT_CTRL 0x0803
|
|
#define B43_PHY_NRSSILT_DATA 0x0804
|
|
|
|
/* RadioRegisters */
|
|
#define B43_RADIOCTL_ID 0x01
|
|
|
|
/* MAC Control bitfield */
|
|
#define B43_MACCTL_ENABLED 0x00000001 /* MAC Enabled */
|
|
#define B43_MACCTL_PSM_RUN 0x00000002 /* Run Microcode */
|
|
#define B43_MACCTL_PSM_JMP0 0x00000004 /* Microcode jump to 0 */
|
|
#define B43_MACCTL_SHM_ENABLED 0x00000100 /* SHM Enabled */
|
|
#define B43_MACCTL_SHM_UPPER 0x00000200 /* SHM Upper */
|
|
#define B43_MACCTL_IHR_ENABLED 0x00000400 /* IHR Region Enabled */
|
|
#define B43_MACCTL_PSM_DBG 0x00002000 /* Microcode debugging enabled */
|
|
#define B43_MACCTL_GPOUTSMSK 0x0000C000 /* GPOUT Select Mask */
|
|
#define B43_MACCTL_BE 0x00010000 /* Big Endian mode */
|
|
#define B43_MACCTL_INFRA 0x00020000 /* Infrastructure mode */
|
|
#define B43_MACCTL_AP 0x00040000 /* AccessPoint mode */
|
|
#define B43_MACCTL_RADIOLOCK 0x00080000 /* Radio lock */
|
|
#define B43_MACCTL_BEACPROMISC 0x00100000 /* Beacon Promiscuous */
|
|
#define B43_MACCTL_KEEP_BADPLCP 0x00200000 /* Keep frames with bad PLCP */
|
|
#define B43_MACCTL_KEEP_CTL 0x00400000 /* Keep control frames */
|
|
#define B43_MACCTL_KEEP_BAD 0x00800000 /* Keep bad frames (FCS) */
|
|
#define B43_MACCTL_PROMISC 0x01000000 /* Promiscuous mode */
|
|
#define B43_MACCTL_HWPS 0x02000000 /* Hardware Power Saving */
|
|
#define B43_MACCTL_AWAKE 0x04000000 /* Device is awake */
|
|
#define B43_MACCTL_CLOSEDNET 0x08000000 /* Closed net (no SSID bcast) */
|
|
#define B43_MACCTL_TBTTHOLD 0x10000000 /* TBTT Hold */
|
|
#define B43_MACCTL_DISCTXSTAT 0x20000000 /* Discard TX status */
|
|
#define B43_MACCTL_DISCPMQ 0x40000000 /* Discard Power Management Queue */
|
|
#define B43_MACCTL_GMODE 0x80000000 /* G Mode */
|
|
|
|
/* MAC Command bitfield */
|
|
#define B43_MACCMD_BEACON0_VALID 0x00000001 /* Beacon 0 in template RAM is busy/valid */
|
|
#define B43_MACCMD_BEACON1_VALID 0x00000002 /* Beacon 1 in template RAM is busy/valid */
|
|
#define B43_MACCMD_DFQ_VALID 0x00000004 /* Directed frame queue valid (IBSS PS mode, ATIM) */
|
|
#define B43_MACCMD_CCA 0x00000008 /* Clear channel assessment */
|
|
#define B43_MACCMD_BGNOISE 0x00000010 /* Background noise */
|
|
|
|
/* 802.11 core specific TM State Low (SSB_TMSLOW) flags */
|
|
#define B43_TMSLOW_GMODE 0x20000000 /* G Mode Enable */
|
|
#define B43_TMSLOW_PHYCLKSPEED 0x00C00000 /* PHY clock speed mask (N-PHY only) */
|
|
#define B43_TMSLOW_PHYCLKSPEED_40MHZ 0x00000000 /* 40 MHz PHY */
|
|
#define B43_TMSLOW_PHYCLKSPEED_80MHZ 0x00400000 /* 80 MHz PHY */
|
|
#define B43_TMSLOW_PHYCLKSPEED_160MHZ 0x00800000 /* 160 MHz PHY */
|
|
#define B43_TMSLOW_PLLREFSEL 0x00200000 /* PLL Frequency Reference Select (rev >= 5) */
|
|
#define B43_TMSLOW_MACPHYCLKEN 0x00100000 /* MAC PHY Clock Control Enable (rev >= 5) */
|
|
#define B43_TMSLOW_PHYRESET 0x00080000 /* PHY Reset */
|
|
#define B43_TMSLOW_PHYCLKEN 0x00040000 /* PHY Clock Enable */
|
|
|
|
/* 802.11 core specific TM State High (SSB_TMSHIGH) flags */
|
|
#define B43_TMSHIGH_DUALBAND_PHY 0x00080000 /* Dualband PHY available */
|
|
#define B43_TMSHIGH_FCLOCK 0x00040000 /* Fast Clock Available (rev >= 5) */
|
|
#define B43_TMSHIGH_HAVE_5GHZ_PHY 0x00020000 /* 5 GHz PHY available (rev >= 5) */
|
|
#define B43_TMSHIGH_HAVE_2GHZ_PHY 0x00010000 /* 2.4 GHz PHY available (rev >= 5) */
|
|
|
|
/* Generic-Interrupt reasons. */
|
|
#define B43_IRQ_MAC_SUSPENDED 0x00000001
|
|
#define B43_IRQ_BEACON 0x00000002
|
|
#define B43_IRQ_TBTT_INDI 0x00000004
|
|
#define B43_IRQ_BEACON_TX_OK 0x00000008
|
|
#define B43_IRQ_BEACON_CANCEL 0x00000010
|
|
#define B43_IRQ_ATIM_END 0x00000020
|
|
#define B43_IRQ_PMQ 0x00000040
|
|
#define B43_IRQ_PIO_WORKAROUND 0x00000100
|
|
#define B43_IRQ_MAC_TXERR 0x00000200
|
|
#define B43_IRQ_PHY_TXERR 0x00000800
|
|
#define B43_IRQ_PMEVENT 0x00001000
|
|
#define B43_IRQ_TIMER0 0x00002000
|
|
#define B43_IRQ_TIMER1 0x00004000
|
|
#define B43_IRQ_DMA 0x00008000
|
|
#define B43_IRQ_TXFIFO_FLUSH_OK 0x00010000
|
|
#define B43_IRQ_CCA_MEASURE_OK 0x00020000
|
|
#define B43_IRQ_NOISESAMPLE_OK 0x00040000
|
|
#define B43_IRQ_UCODE_DEBUG 0x08000000
|
|
#define B43_IRQ_RFKILL 0x10000000
|
|
#define B43_IRQ_TX_OK 0x20000000
|
|
#define B43_IRQ_PHY_G_CHANGED 0x40000000
|
|
#define B43_IRQ_TIMEOUT 0x80000000
|
|
|
|
#define B43_IRQ_ALL 0xFFFFFFFF
|
|
#define B43_IRQ_MASKTEMPLATE (B43_IRQ_TBTT_INDI | \
|
|
B43_IRQ_ATIM_END | \
|
|
B43_IRQ_PMQ | \
|
|
B43_IRQ_MAC_TXERR | \
|
|
B43_IRQ_PHY_TXERR | \
|
|
B43_IRQ_DMA | \
|
|
B43_IRQ_TXFIFO_FLUSH_OK | \
|
|
B43_IRQ_NOISESAMPLE_OK | \
|
|
B43_IRQ_UCODE_DEBUG | \
|
|
B43_IRQ_RFKILL | \
|
|
B43_IRQ_TX_OK)
|
|
|
|
/* The firmware register to fetch the debug-IRQ reason from. */
|
|
#define B43_DEBUGIRQ_REASON_REG 63
|
|
/* Debug-IRQ reasons. */
|
|
#define B43_DEBUGIRQ_PANIC 0 /* The firmware panic'ed */
|
|
#define B43_DEBUGIRQ_DUMP_SHM 1 /* Dump shared SHM */
|
|
#define B43_DEBUGIRQ_DUMP_REGS 2 /* Dump the microcode registers */
|
|
#define B43_DEBUGIRQ_MARKER 3 /* A "marker" was thrown by the firmware. */
|
|
#define B43_DEBUGIRQ_ACK 0xFFFF /* The host writes that to ACK the IRQ */
|
|
|
|
/* The firmware register that contains the "marker" line. */
|
|
#define B43_MARKER_ID_REG 2
|
|
#define B43_MARKER_LINE_REG 3
|
|
|
|
/* The firmware register to fetch the panic reason from. */
|
|
#define B43_FWPANIC_REASON_REG 3
|
|
/* Firmware panic reason codes */
|
|
#define B43_FWPANIC_DIE 0 /* Firmware died. Don't auto-restart it. */
|
|
#define B43_FWPANIC_RESTART 1 /* Firmware died. Schedule a controller reset. */
|
|
|
|
/* The firmware register that contains the watchdog counter. */
|
|
#define B43_WATCHDOG_REG 1
|
|
|
|
/* Device specific rate values.
|
|
* The actual values defined here are (rate_in_mbps * 2).
|
|
* Some code depends on this. Don't change it. */
|
|
#define B43_CCK_RATE_1MB 0x02
|
|
#define B43_CCK_RATE_2MB 0x04
|
|
#define B43_CCK_RATE_5MB 0x0B
|
|
#define B43_CCK_RATE_11MB 0x16
|
|
#define B43_OFDM_RATE_6MB 0x0C
|
|
#define B43_OFDM_RATE_9MB 0x12
|
|
#define B43_OFDM_RATE_12MB 0x18
|
|
#define B43_OFDM_RATE_18MB 0x24
|
|
#define B43_OFDM_RATE_24MB 0x30
|
|
#define B43_OFDM_RATE_36MB 0x48
|
|
#define B43_OFDM_RATE_48MB 0x60
|
|
#define B43_OFDM_RATE_54MB 0x6C
|
|
/* Convert a b43 rate value to a rate in 100kbps */
|
|
#define B43_RATE_TO_BASE100KBPS(rate) (((rate) * 10) / 2)
|
|
|
|
#define B43_DEFAULT_SHORT_RETRY_LIMIT 7
|
|
#define B43_DEFAULT_LONG_RETRY_LIMIT 4
|
|
|
|
#define B43_PHY_TX_BADNESS_LIMIT 1000
|
|
|
|
/* Max size of a security key */
|
|
#define B43_SEC_KEYSIZE 16
|
|
/* Security algorithms. */
|
|
enum {
|
|
B43_SEC_ALGO_NONE = 0, /* unencrypted, as of TX header. */
|
|
B43_SEC_ALGO_WEP40,
|
|
B43_SEC_ALGO_TKIP,
|
|
B43_SEC_ALGO_AES,
|
|
B43_SEC_ALGO_WEP104,
|
|
B43_SEC_ALGO_AES_LEGACY,
|
|
};
|
|
|
|
struct b43_dmaring;
|
|
|
|
/* The firmware file header */
|
|
#define B43_FW_TYPE_UCODE 'u'
|
|
#define B43_FW_TYPE_PCM 'p'
|
|
#define B43_FW_TYPE_IV 'i'
|
|
struct b43_fw_header {
|
|
/* File type */
|
|
u8 type;
|
|
/* File format version */
|
|
u8 ver;
|
|
u8 __padding[2];
|
|
/* Size of the data. For ucode and PCM this is in bytes.
|
|
* For IV this is number-of-ivs. */
|
|
__be32 size;
|
|
} __attribute__((__packed__));
|
|
|
|
/* Initial Value file format */
|
|
#define B43_IV_OFFSET_MASK 0x7FFF
|
|
#define B43_IV_32BIT 0x8000
|
|
struct b43_iv {
|
|
__be16 offset_size;
|
|
union {
|
|
__be16 d16;
|
|
__be32 d32;
|
|
} data __attribute__((__packed__));
|
|
} __attribute__((__packed__));
|
|
|
|
|
|
struct b43_phy {
|
|
/* Band support flags. */
|
|
bool supports_2ghz;
|
|
bool supports_5ghz;
|
|
|
|
/* GMODE bit enabled? */
|
|
bool gmode;
|
|
|
|
/* Analog Type */
|
|
u8 analog;
|
|
/* B43_PHYTYPE_ */
|
|
u8 type;
|
|
/* PHY revision number. */
|
|
u8 rev;
|
|
|
|
/* Radio versioning */
|
|
u16 radio_manuf; /* Radio manufacturer */
|
|
u16 radio_ver; /* Radio version */
|
|
u8 radio_rev; /* Radio revision */
|
|
|
|
bool dyn_tssi_tbl; /* tssi2dbm is kmalloc()ed. */
|
|
|
|
/* ACI (adjacent channel interference) flags. */
|
|
bool aci_enable;
|
|
bool aci_wlan_automatic;
|
|
bool aci_hw_rssi;
|
|
|
|
/* Radio switched on/off */
|
|
bool radio_on;
|
|
struct {
|
|
/* Values saved when turning the radio off.
|
|
* They are needed when turning it on again. */
|
|
bool valid;
|
|
u16 rfover;
|
|
u16 rfoverval;
|
|
} radio_off_context;
|
|
|
|
u16 minlowsig[2];
|
|
u16 minlowsigpos[2];
|
|
|
|
/* TSSI to dBm table in use */
|
|
const s8 *tssi2dbm;
|
|
/* Target idle TSSI */
|
|
int tgt_idle_tssi;
|
|
/* Current idle TSSI */
|
|
int cur_idle_tssi;
|
|
|
|
/* LocalOscillator control values. */
|
|
struct b43_txpower_lo_control *lo_control;
|
|
/* Values from b43_calc_loopback_gain() */
|
|
s16 max_lb_gain; /* Maximum Loopback gain in hdB */
|
|
s16 trsw_rx_gain; /* TRSW RX gain in hdB */
|
|
s16 lna_lod_gain; /* LNA lod */
|
|
s16 lna_gain; /* LNA */
|
|
s16 pga_gain; /* PGA */
|
|
|
|
/* Desired TX power level (in dBm).
|
|
* This is set by the user and adjusted in b43_phy_xmitpower(). */
|
|
u8 power_level;
|
|
/* A-PHY TX Power control value. */
|
|
u16 txpwr_offset;
|
|
|
|
/* Current TX power level attenuation control values */
|
|
struct b43_bbatt bbatt;
|
|
struct b43_rfatt rfatt;
|
|
u8 tx_control; /* B43_TXCTL_XXX */
|
|
|
|
/* Hardware Power Control enabled? */
|
|
bool hardware_power_control;
|
|
|
|
/* Current Interference Mitigation mode */
|
|
int interfmode;
|
|
/* Stack of saved values from the Interference Mitigation code.
|
|
* Each value in the stack is layed out as follows:
|
|
* bit 0-11: offset
|
|
* bit 12-15: register ID
|
|
* bit 16-32: value
|
|
* register ID is: 0x1 PHY, 0x2 Radio, 0x3 ILT
|
|
*/
|
|
#define B43_INTERFSTACK_SIZE 26
|
|
u32 interfstack[B43_INTERFSTACK_SIZE]; //FIXME: use a data structure
|
|
|
|
/* Saved values from the NRSSI Slope calculation */
|
|
s16 nrssi[2];
|
|
s32 nrssislope;
|
|
/* In memory nrssi lookup table. */
|
|
s8 nrssi_lt[64];
|
|
|
|
/* current channel */
|
|
u8 channel;
|
|
|
|
u16 lofcal;
|
|
|
|
u16 initval; //FIXME rename?
|
|
|
|
/* PHY TX errors counter. */
|
|
atomic_t txerr_cnt;
|
|
|
|
/* The device does address auto increment for the OFDM tables.
|
|
* We cache the previously used address here and omit the address
|
|
* write on the next table access, if possible. */
|
|
u16 ofdmtab_addr; /* The address currently set in hardware. */
|
|
enum { /* The last data flow direction. */
|
|
B43_OFDMTAB_DIRECTION_UNKNOWN = 0,
|
|
B43_OFDMTAB_DIRECTION_READ,
|
|
B43_OFDMTAB_DIRECTION_WRITE,
|
|
} ofdmtab_addr_direction;
|
|
|
|
#if B43_DEBUG
|
|
/* Manual TX-power control enabled? */
|
|
bool manual_txpower_control;
|
|
/* PHY registers locked by b43_phy_lock()? */
|
|
bool phy_locked;
|
|
#endif /* B43_DEBUG */
|
|
};
|
|
|
|
/* Data structures for DMA transmission, per 80211 core. */
|
|
struct b43_dma {
|
|
struct b43_dmaring *tx_ring_AC_BK; /* Background */
|
|
struct b43_dmaring *tx_ring_AC_BE; /* Best Effort */
|
|
struct b43_dmaring *tx_ring_AC_VI; /* Video */
|
|
struct b43_dmaring *tx_ring_AC_VO; /* Voice */
|
|
struct b43_dmaring *tx_ring_mcast; /* Multicast */
|
|
|
|
struct b43_dmaring *rx_ring;
|
|
};
|
|
|
|
struct b43_pio_txqueue;
|
|
struct b43_pio_rxqueue;
|
|
|
|
/* Data structures for PIO transmission, per 80211 core. */
|
|
struct b43_pio {
|
|
struct b43_pio_txqueue *tx_queue_AC_BK; /* Background */
|
|
struct b43_pio_txqueue *tx_queue_AC_BE; /* Best Effort */
|
|
struct b43_pio_txqueue *tx_queue_AC_VI; /* Video */
|
|
struct b43_pio_txqueue *tx_queue_AC_VO; /* Voice */
|
|
struct b43_pio_txqueue *tx_queue_mcast; /* Multicast */
|
|
|
|
struct b43_pio_rxqueue *rx_queue;
|
|
};
|
|
|
|
/* Context information for a noise calculation (Link Quality). */
|
|
struct b43_noise_calculation {
|
|
bool calculation_running;
|
|
u8 nr_samples;
|
|
s8 samples[8][4];
|
|
};
|
|
|
|
struct b43_stats {
|
|
u8 link_noise;
|
|
/* Store the last TX/RX times here for updating the leds. */
|
|
unsigned long last_tx;
|
|
unsigned long last_rx;
|
|
};
|
|
|
|
struct b43_key {
|
|
/* If keyconf is NULL, this key is disabled.
|
|
* keyconf is a cookie. Don't derefenrence it outside of the set_key
|
|
* path, because b43 doesn't own it. */
|
|
struct ieee80211_key_conf *keyconf;
|
|
u8 algorithm;
|
|
};
|
|
|
|
/* SHM offsets to the QOS data structures for the 4 different queues. */
|
|
#define B43_QOS_PARAMS(queue) (B43_SHM_SH_EDCFQ + \
|
|
(B43_NR_QOSPARAMS * sizeof(u16) * (queue)))
|
|
#define B43_QOS_BACKGROUND B43_QOS_PARAMS(0)
|
|
#define B43_QOS_BESTEFFORT B43_QOS_PARAMS(1)
|
|
#define B43_QOS_VIDEO B43_QOS_PARAMS(2)
|
|
#define B43_QOS_VOICE B43_QOS_PARAMS(3)
|
|
|
|
/* QOS parameter hardware data structure offsets. */
|
|
#define B43_NR_QOSPARAMS 22
|
|
enum {
|
|
B43_QOSPARAM_TXOP = 0,
|
|
B43_QOSPARAM_CWMIN,
|
|
B43_QOSPARAM_CWMAX,
|
|
B43_QOSPARAM_CWCUR,
|
|
B43_QOSPARAM_AIFS,
|
|
B43_QOSPARAM_BSLOTS,
|
|
B43_QOSPARAM_REGGAP,
|
|
B43_QOSPARAM_STATUS,
|
|
};
|
|
|
|
/* QOS parameters for a queue. */
|
|
struct b43_qos_params {
|
|
/* The QOS parameters */
|
|
struct ieee80211_tx_queue_params p;
|
|
/* Does this need to get uploaded to hardware? */
|
|
bool need_hw_update;
|
|
};
|
|
|
|
struct b43_wldev;
|
|
|
|
/* Data structure for the WLAN parts (802.11 cores) of the b43 chip. */
|
|
struct b43_wl {
|
|
/* Pointer to the active wireless device on this chip */
|
|
struct b43_wldev *current_dev;
|
|
/* Pointer to the ieee80211 hardware data structure */
|
|
struct ieee80211_hw *hw;
|
|
|
|
struct mutex mutex;
|
|
spinlock_t irq_lock;
|
|
/* R/W lock for data transmission.
|
|
* Transmissions on 2+ queues can run concurrently, but somebody else
|
|
* might sync with TX by write_lock_irqsave()'ing. */
|
|
rwlock_t tx_lock;
|
|
/* Lock for LEDs access. */
|
|
spinlock_t leds_lock;
|
|
/* Lock for SHM access. */
|
|
spinlock_t shm_lock;
|
|
|
|
/* We can only have one operating interface (802.11 core)
|
|
* at a time. General information about this interface follows.
|
|
*/
|
|
|
|
struct ieee80211_vif *vif;
|
|
/* The MAC address of the operating interface. */
|
|
u8 mac_addr[ETH_ALEN];
|
|
/* Current BSSID */
|
|
u8 bssid[ETH_ALEN];
|
|
/* Interface type. (IEEE80211_IF_TYPE_XXX) */
|
|
int if_type;
|
|
/* Is the card operating in AP, STA or IBSS mode? */
|
|
bool operating;
|
|
/* filter flags */
|
|
unsigned int filter_flags;
|
|
/* Stats about the wireless interface */
|
|
struct ieee80211_low_level_stats ieee_stats;
|
|
|
|
struct hwrng rng;
|
|
u8 rng_initialized;
|
|
char rng_name[30 + 1];
|
|
|
|
/* The RF-kill button */
|
|
struct b43_rfkill rfkill;
|
|
|
|
/* List of all wireless devices on this chip */
|
|
struct list_head devlist;
|
|
u8 nr_devs;
|
|
|
|
bool radiotap_enabled;
|
|
|
|
/* The beacon we are currently using (AP or IBSS mode).
|
|
* This beacon stuff is protected by the irq_lock. */
|
|
struct sk_buff *current_beacon;
|
|
bool beacon0_uploaded;
|
|
bool beacon1_uploaded;
|
|
bool beacon_templates_virgin; /* Never wrote the templates? */
|
|
struct work_struct beacon_update_trigger;
|
|
|
|
/* The current QOS parameters for the 4 queues.
|
|
* This is protected by the irq_lock. */
|
|
struct b43_qos_params qos_params[4];
|
|
/* Workqueue for updating QOS parameters in hardware. */
|
|
struct work_struct qos_update_work;
|
|
};
|
|
|
|
/* In-memory representation of a cached microcode file. */
|
|
struct b43_firmware_file {
|
|
const char *filename;
|
|
const struct firmware *data;
|
|
};
|
|
|
|
/* Pointers to the firmware data and meta information about it. */
|
|
struct b43_firmware {
|
|
/* Microcode */
|
|
struct b43_firmware_file ucode;
|
|
/* PCM code */
|
|
struct b43_firmware_file pcm;
|
|
/* Initial MMIO values for the firmware */
|
|
struct b43_firmware_file initvals;
|
|
/* Initial MMIO values for the firmware, band-specific */
|
|
struct b43_firmware_file initvals_band;
|
|
|
|
/* Firmware revision */
|
|
u16 rev;
|
|
/* Firmware patchlevel */
|
|
u16 patch;
|
|
|
|
/* Set to true, if we are using an opensource firmware. */
|
|
bool opensource;
|
|
/* Set to true, if the core needs a PCM firmware, but
|
|
* we failed to load one. This is always false for
|
|
* core rev > 10, as these don't need PCM firmware. */
|
|
bool pcm_request_failed;
|
|
};
|
|
|
|
/* Device (802.11 core) initialization status. */
|
|
enum {
|
|
B43_STAT_UNINIT = 0, /* Uninitialized. */
|
|
B43_STAT_INITIALIZED = 1, /* Initialized, but not started, yet. */
|
|
B43_STAT_STARTED = 2, /* Up and running. */
|
|
};
|
|
#define b43_status(wldev) atomic_read(&(wldev)->__init_status)
|
|
#define b43_set_status(wldev, stat) do { \
|
|
atomic_set(&(wldev)->__init_status, (stat)); \
|
|
smp_wmb(); \
|
|
} while (0)
|
|
|
|
/* XXX--- HOW LOCKING WORKS IN B43 ---XXX
|
|
*
|
|
* You should always acquire both, wl->mutex and wl->irq_lock unless:
|
|
* - You don't need to acquire wl->irq_lock, if the interface is stopped.
|
|
* - You don't need to acquire wl->mutex in the IRQ handler, IRQ tasklet
|
|
* and packet TX path (and _ONLY_ there.)
|
|
*/
|
|
|
|
/* Data structure for one wireless device (802.11 core) */
|
|
struct b43_wldev {
|
|
struct ssb_device *dev;
|
|
struct b43_wl *wl;
|
|
|
|
/* The device initialization status.
|
|
* Use b43_status() to query. */
|
|
atomic_t __init_status;
|
|
/* Saved init status for handling suspend. */
|
|
int suspend_init_status;
|
|
|
|
bool bad_frames_preempt; /* Use "Bad Frames Preemption" (default off) */
|
|
bool dfq_valid; /* Directed frame queue valid (IBSS PS mode, ATIM) */
|
|
bool short_slot; /* TRUE, if short slot timing is enabled. */
|
|
bool radio_hw_enable; /* saved state of radio hardware enabled state */
|
|
bool suspend_in_progress; /* TRUE, if we are in a suspend/resume cycle */
|
|
|
|
/* PHY/Radio device. */
|
|
struct b43_phy phy;
|
|
|
|
union {
|
|
/* DMA engines. */
|
|
struct b43_dma dma;
|
|
/* PIO engines. */
|
|
struct b43_pio pio;
|
|
};
|
|
/* Use b43_using_pio_transfers() to check whether we are using
|
|
* DMA or PIO data transfers. */
|
|
bool __using_pio_transfers;
|
|
|
|
/* Various statistics about the physical device. */
|
|
struct b43_stats stats;
|
|
|
|
/* The device LEDs. */
|
|
struct b43_led led_tx;
|
|
struct b43_led led_rx;
|
|
struct b43_led led_assoc;
|
|
struct b43_led led_radio;
|
|
|
|
/* Reason code of the last interrupt. */
|
|
u32 irq_reason;
|
|
u32 dma_reason[6];
|
|
/* saved irq enable/disable state bitfield. */
|
|
u32 irq_savedstate;
|
|
/* Link Quality calculation context. */
|
|
struct b43_noise_calculation noisecalc;
|
|
/* if > 0 MAC is suspended. if == 0 MAC is enabled. */
|
|
int mac_suspended;
|
|
|
|
/* Interrupt Service Routine tasklet (bottom-half) */
|
|
struct tasklet_struct isr_tasklet;
|
|
|
|
/* Periodic tasks */
|
|
struct delayed_work periodic_work;
|
|
unsigned int periodic_state;
|
|
|
|
struct work_struct restart_work;
|
|
|
|
/* encryption/decryption */
|
|
u16 ktp; /* Key table pointer */
|
|
u8 max_nr_keys;
|
|
struct b43_key key[58];
|
|
|
|
/* Firmware data */
|
|
struct b43_firmware fw;
|
|
|
|
/* Devicelist in struct b43_wl (all 802.11 cores) */
|
|
struct list_head list;
|
|
|
|
/* Debugging stuff follows. */
|
|
#ifdef CONFIG_B43_DEBUG
|
|
struct b43_dfsentry *dfsentry;
|
|
#endif
|
|
};
|
|
|
|
static inline struct b43_wl *hw_to_b43_wl(struct ieee80211_hw *hw)
|
|
{
|
|
return hw->priv;
|
|
}
|
|
|
|
static inline struct b43_wldev *dev_to_b43_wldev(struct device *dev)
|
|
{
|
|
struct ssb_device *ssb_dev = dev_to_ssb_dev(dev);
|
|
return ssb_get_drvdata(ssb_dev);
|
|
}
|
|
|
|
/* Is the device operating in a specified mode (IEEE80211_IF_TYPE_XXX). */
|
|
static inline int b43_is_mode(struct b43_wl *wl, int type)
|
|
{
|
|
return (wl->operating && wl->if_type == type);
|
|
}
|
|
|
|
static inline u16 b43_read16(struct b43_wldev *dev, u16 offset)
|
|
{
|
|
return ssb_read16(dev->dev, offset);
|
|
}
|
|
|
|
static inline void b43_write16(struct b43_wldev *dev, u16 offset, u16 value)
|
|
{
|
|
ssb_write16(dev->dev, offset, value);
|
|
}
|
|
|
|
static inline u32 b43_read32(struct b43_wldev *dev, u16 offset)
|
|
{
|
|
return ssb_read32(dev->dev, offset);
|
|
}
|
|
|
|
static inline void b43_write32(struct b43_wldev *dev, u16 offset, u32 value)
|
|
{
|
|
ssb_write32(dev->dev, offset, value);
|
|
}
|
|
|
|
static inline bool b43_using_pio_transfers(struct b43_wldev *dev)
|
|
{
|
|
#ifdef CONFIG_B43_PIO
|
|
return dev->__using_pio_transfers;
|
|
#else
|
|
return 0;
|
|
#endif
|
|
}
|
|
|
|
#ifdef CONFIG_B43_FORCE_PIO
|
|
# define B43_FORCE_PIO 1
|
|
#else
|
|
# define B43_FORCE_PIO 0
|
|
#endif
|
|
|
|
|
|
/* Message printing */
|
|
void b43info(struct b43_wl *wl, const char *fmt, ...)
|
|
__attribute__ ((format(printf, 2, 3)));
|
|
void b43err(struct b43_wl *wl, const char *fmt, ...)
|
|
__attribute__ ((format(printf, 2, 3)));
|
|
void b43warn(struct b43_wl *wl, const char *fmt, ...)
|
|
__attribute__ ((format(printf, 2, 3)));
|
|
#if B43_DEBUG
|
|
void b43dbg(struct b43_wl *wl, const char *fmt, ...)
|
|
__attribute__ ((format(printf, 2, 3)));
|
|
#else /* DEBUG */
|
|
# define b43dbg(wl, fmt...) do { /* nothing */ } while (0)
|
|
#endif /* DEBUG */
|
|
|
|
/* A WARN_ON variant that vanishes when b43 debugging is disabled.
|
|
* This _also_ evaluates the arg with debugging disabled. */
|
|
#if B43_DEBUG
|
|
# define B43_WARN_ON(x) WARN_ON(x)
|
|
#else
|
|
static inline bool __b43_warn_on_dummy(bool x) { return x; }
|
|
# define B43_WARN_ON(x) __b43_warn_on_dummy(unlikely(!!(x)))
|
|
#endif
|
|
|
|
/* Convert an integer to a Q5.2 value */
|
|
#define INT_TO_Q52(i) ((i) << 2)
|
|
/* Convert a Q5.2 value to an integer (precision loss!) */
|
|
#define Q52_TO_INT(q52) ((q52) >> 2)
|
|
/* Macros for printing a value in Q5.2 format */
|
|
#define Q52_FMT "%u.%u"
|
|
#define Q52_ARG(q52) Q52_TO_INT(q52), ((((q52) & 0x3) * 100) / 4)
|
|
|
|
#endif /* B43_H_ */
|