a4d9f179cc
Adding flag on fixed regulator board configuration structure to specify whether gpio is open drain type or not. Passing this information to gpio library when requesting gpio so that gpio driver can set the pin state accordingly, for open drain type: - Pin can be set HIGH as setting as input, PULL UP on pin make this as HIGH. - Pin can be set LOW as setting it as output and drive to LOW. The non-open drain pin can be set HIGH/LOW by setting it to output and driving it to HIGH/LOW. Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
72 lines
2.2 KiB
C
72 lines
2.2 KiB
C
/*
|
|
* fixed.h
|
|
*
|
|
* Copyright 2008 Wolfson Microelectronics PLC.
|
|
*
|
|
* Author: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
*
|
|
* Copyright (c) 2009 Nokia Corporation
|
|
* Roger Quadros <ext-roger.quadros@nokia.com>
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License as
|
|
* published by the Free Software Foundation; either version 2 of the
|
|
* License, or (at your option) any later version.
|
|
*/
|
|
|
|
#ifndef __REGULATOR_FIXED_H
|
|
#define __REGULATOR_FIXED_H
|
|
|
|
struct regulator_init_data;
|
|
|
|
/**
|
|
* struct fixed_voltage_config - fixed_voltage_config structure
|
|
* @supply_name: Name of the regulator supply
|
|
* @microvolts: Output voltage of regulator
|
|
* @gpio: GPIO to use for enable control
|
|
* set to -EINVAL if not used
|
|
* @startup_delay: Start-up time in microseconds
|
|
* @gpio_is_open_drain: Gpio pin is open drain or normal type.
|
|
* If it is open drain type then HIGH will be set
|
|
* through PULL-UP with setting gpio as input
|
|
* and low will be set as gpio-output with driven
|
|
* to low. For non-open-drain case, the gpio will
|
|
* will be in output and drive to low/high accordingly.
|
|
* @enable_high: Polarity of enable GPIO
|
|
* 1 = Active high, 0 = Active low
|
|
* @enabled_at_boot: Whether regulator has been enabled at
|
|
* boot or not. 1 = Yes, 0 = No
|
|
* This is used to keep the regulator at
|
|
* the default state
|
|
* @init_data: regulator_init_data
|
|
*
|
|
* This structure contains fixed voltage regulator configuration
|
|
* information that must be passed by platform code to the fixed
|
|
* voltage regulator driver.
|
|
*/
|
|
struct fixed_voltage_config {
|
|
const char *supply_name;
|
|
int microvolts;
|
|
int gpio;
|
|
unsigned startup_delay;
|
|
unsigned gpio_is_open_drain:1;
|
|
unsigned enable_high:1;
|
|
unsigned enabled_at_boot:1;
|
|
struct regulator_init_data *init_data;
|
|
};
|
|
|
|
struct regulator_consumer_supply;
|
|
|
|
#if IS_ENABLED(CONFIG_REGULATOR)
|
|
struct platform_device *regulator_register_fixed(int id,
|
|
struct regulator_consumer_supply *supplies, int num_supplies);
|
|
#else
|
|
static inline struct platform_device *regulator_register_fixed(int id,
|
|
struct regulator_consumer_supply *supplies, int num_supplies)
|
|
{
|
|
return NULL;
|
|
}
|
|
#endif
|
|
|
|
#endif
|