![Bartlomiej Zolnierkiewicz](/assets/img/avatar_default.png)
* Add struct ide_io_ports and use it instead of `unsigned long io_ports[]` in ide_hwif_t. * Rename io_ports[] in hw_regs_t to io_ports_array[]. * Use un-named union for 'unsigned long io_ports_array[]' and 'struct ide_io_ports io_ports' in hw_regs_t. * Remove IDE_*_OFFSET defines. v2: * scc_pata.c build fix from Stephen Rothwell. v3: * Fix ctl_adrr typo in Sparc-specific part of ns87415.c. (Noticed by Andrew Morton) Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
368 lines
11 KiB
C
368 lines
11 KiB
C
/*
|
|
* Copyright (c) 1997-1998 Mark Lord
|
|
* Copyright (c) 2007 MontaVista Software, Inc. <source@mvista.com>
|
|
*
|
|
* May be copied or modified under the terms of the GNU General Public License
|
|
*
|
|
* June 22, 2004 - get rid of check_region
|
|
* - Jesper Juhl
|
|
*
|
|
*/
|
|
|
|
/*
|
|
* This module provides support for the bus-master IDE DMA function
|
|
* of the Tekram TRM290 chip, used on a variety of PCI IDE add-on boards,
|
|
* including a "Precision Instruments" board. The TRM290 pre-dates
|
|
* the sff-8038 standard (ide-dma.c) by a few months, and differs
|
|
* significantly enough to warrant separate routines for some functions,
|
|
* while re-using others from ide-dma.c.
|
|
*
|
|
* EXPERIMENTAL! It works for me (a sample of one).
|
|
*
|
|
* Works reliably for me in DMA mode (READs only),
|
|
* DMA WRITEs are disabled by default (see #define below);
|
|
*
|
|
* DMA is not enabled automatically for this chipset,
|
|
* but can be turned on manually (with "hdparm -d1") at run time.
|
|
*
|
|
* I need volunteers with "spare" drives for further testing
|
|
* and development, and maybe to help figure out the peculiarities.
|
|
* Even knowing the registers (below), some things behave strangely.
|
|
*/
|
|
|
|
#define TRM290_NO_DMA_WRITES /* DMA writes seem unreliable sometimes */
|
|
|
|
/*
|
|
* TRM-290 PCI-IDE2 Bus Master Chip
|
|
* ================================
|
|
* The configuration registers are addressed in normal I/O port space
|
|
* and are used as follows:
|
|
*
|
|
* trm290_base depends on jumper settings, and is probed for by ide-dma.c
|
|
*
|
|
* trm290_base+2 when WRITTEN: chiptest register (byte, write-only)
|
|
* bit7 must always be written as "1"
|
|
* bits6-2 undefined
|
|
* bit1 1=legacy_compatible_mode, 0=native_pci_mode
|
|
* bit0 1=test_mode, 0=normal(default)
|
|
*
|
|
* trm290_base+2 when READ: status register (byte, read-only)
|
|
* bits7-2 undefined
|
|
* bit1 channel0 busmaster interrupt status 0=none, 1=asserted
|
|
* bit0 channel0 interrupt status 0=none, 1=asserted
|
|
*
|
|
* trm290_base+3 Interrupt mask register
|
|
* bits7-5 undefined
|
|
* bit4 legacy_header: 1=present, 0=absent
|
|
* bit3 channel1 busmaster interrupt status 0=none, 1=asserted (read only)
|
|
* bit2 channel1 interrupt status 0=none, 1=asserted (read only)
|
|
* bit1 channel1 interrupt mask: 1=masked, 0=unmasked(default)
|
|
* bit0 channel0 interrupt mask: 1=masked, 0=unmasked(default)
|
|
*
|
|
* trm290_base+1 "CPR" Config Pointer Register (byte)
|
|
* bit7 1=autoincrement CPR bits 2-0 after each access of CDR
|
|
* bit6 1=min. 1 wait-state posted write cycle (default), 0=0 wait-state
|
|
* bit5 0=enabled master burst access (default), 1=disable (write only)
|
|
* bit4 PCI DEVSEL# timing select: 1=medium(default), 0=fast
|
|
* bit3 0=primary IDE channel, 1=secondary IDE channel
|
|
* bits2-0 register index for accesses through CDR port
|
|
*
|
|
* trm290_base+0 "CDR" Config Data Register (word)
|
|
* two sets of seven config registers,
|
|
* selected by CPR bit 3 (channel) and CPR bits 2-0 (index 0 to 6),
|
|
* each index defined below:
|
|
*
|
|
* Index-0 Base address register for command block (word)
|
|
* defaults: 0x1f0 for primary, 0x170 for secondary
|
|
*
|
|
* Index-1 general config register (byte)
|
|
* bit7 1=DMA enable, 0=DMA disable
|
|
* bit6 1=activate IDE_RESET, 0=no action (default)
|
|
* bit5 1=enable IORDY, 0=disable IORDY (default)
|
|
* bit4 0=16-bit data port(default), 1=8-bit (XT) data port
|
|
* bit3 interrupt polarity: 1=active_low, 0=active_high(default)
|
|
* bit2 power-saving-mode(?): 1=enable, 0=disable(default) (write only)
|
|
* bit1 bus_master_mode(?): 1=enable, 0=disable(default)
|
|
* bit0 enable_io_ports: 1=enable(default), 0=disable
|
|
*
|
|
* Index-2 read-ahead counter preload bits 0-7 (byte, write only)
|
|
* bits7-0 bits7-0 of readahead count
|
|
*
|
|
* Index-3 read-ahead config register (byte, write only)
|
|
* bit7 1=enable_readahead, 0=disable_readahead(default)
|
|
* bit6 1=clear_FIFO, 0=no_action
|
|
* bit5 undefined
|
|
* bit4 mode4 timing control: 1=enable, 0=disable(default)
|
|
* bit3 undefined
|
|
* bit2 undefined
|
|
* bits1-0 bits9-8 of read-ahead count
|
|
*
|
|
* Index-4 base address register for control block (word)
|
|
* defaults: 0x3f6 for primary, 0x376 for secondary
|
|
*
|
|
* Index-5 data port timings (shared by both drives) (byte)
|
|
* standard PCI "clk" (clock) counts, default value = 0xf5
|
|
*
|
|
* bits7-6 setup time: 00=1clk, 01=2clk, 10=3clk, 11=4clk
|
|
* bits5-3 hold time: 000=1clk, 001=2clk, 010=3clk,
|
|
* 011=4clk, 100=5clk, 101=6clk,
|
|
* 110=8clk, 111=12clk
|
|
* bits2-0 active time: 000=2clk, 001=3clk, 010=4clk,
|
|
* 011=5clk, 100=6clk, 101=8clk,
|
|
* 110=12clk, 111=16clk
|
|
*
|
|
* Index-6 command/control port timings (shared by both drives) (byte)
|
|
* same layout as Index-5, default value = 0xde
|
|
*
|
|
* Suggested CDR programming for PIO mode0 (600ns):
|
|
* 0x01f0,0x21,0xff,0x80,0x03f6,0xf5,0xde ; primary
|
|
* 0x0170,0x21,0xff,0x80,0x0376,0xf5,0xde ; secondary
|
|
*
|
|
* Suggested CDR programming for PIO mode3 (180ns):
|
|
* 0x01f0,0x21,0xff,0x80,0x03f6,0x09,0xde ; primary
|
|
* 0x0170,0x21,0xff,0x80,0x0376,0x09,0xde ; secondary
|
|
*
|
|
* Suggested CDR programming for PIO mode4 (120ns):
|
|
* 0x01f0,0x21,0xff,0x80,0x03f6,0x00,0xde ; primary
|
|
* 0x0170,0x21,0xff,0x80,0x0376,0x00,0xde ; secondary
|
|
*
|
|
*/
|
|
|
|
#include <linux/types.h>
|
|
#include <linux/module.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/ioport.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/blkdev.h>
|
|
#include <linux/init.h>
|
|
#include <linux/hdreg.h>
|
|
#include <linux/pci.h>
|
|
#include <linux/ide.h>
|
|
|
|
#include <asm/io.h>
|
|
|
|
static void trm290_prepare_drive (ide_drive_t *drive, unsigned int use_dma)
|
|
{
|
|
ide_hwif_t *hwif = HWIF(drive);
|
|
u16 reg = 0;
|
|
unsigned long flags;
|
|
|
|
/* select PIO or DMA */
|
|
reg = use_dma ? (0x21 | 0x82) : (0x21 & ~0x82);
|
|
|
|
local_irq_save(flags);
|
|
|
|
if (reg != hwif->select_data) {
|
|
hwif->select_data = reg;
|
|
/* set PIO/DMA */
|
|
outb(0x51 | (hwif->channel << 3), hwif->config_data + 1);
|
|
outw(reg & 0xff, hwif->config_data);
|
|
}
|
|
|
|
/* enable IRQ if not probing */
|
|
if (drive->present) {
|
|
reg = inw(hwif->config_data + 3);
|
|
reg &= 0x13;
|
|
reg &= ~(1 << hwif->channel);
|
|
outw(reg, hwif->config_data + 3);
|
|
}
|
|
|
|
local_irq_restore(flags);
|
|
}
|
|
|
|
static void trm290_selectproc (ide_drive_t *drive)
|
|
{
|
|
trm290_prepare_drive(drive, drive->using_dma);
|
|
}
|
|
|
|
static void trm290_dma_exec_cmd(ide_drive_t *drive, u8 command)
|
|
{
|
|
ide_execute_command(drive, command, &ide_dma_intr, WAIT_CMD, NULL);
|
|
}
|
|
|
|
static int trm290_dma_setup(ide_drive_t *drive)
|
|
{
|
|
ide_hwif_t *hwif = drive->hwif;
|
|
struct request *rq = hwif->hwgroup->rq;
|
|
unsigned int count, rw;
|
|
|
|
if (rq_data_dir(rq)) {
|
|
#ifdef TRM290_NO_DMA_WRITES
|
|
/* always use PIO for writes */
|
|
trm290_prepare_drive(drive, 0); /* select PIO xfer */
|
|
return 1;
|
|
#endif
|
|
rw = 1;
|
|
} else
|
|
rw = 2;
|
|
|
|
if (!(count = ide_build_dmatable(drive, rq))) {
|
|
/* try PIO instead of DMA */
|
|
trm290_prepare_drive(drive, 0); /* select PIO xfer */
|
|
return 1;
|
|
}
|
|
/* select DMA xfer */
|
|
trm290_prepare_drive(drive, 1);
|
|
outl(hwif->dmatable_dma | rw, hwif->dma_base);
|
|
drive->waiting_for_dma = 1;
|
|
/* start DMA */
|
|
outw(count * 2 - 1, hwif->dma_base + 2);
|
|
return 0;
|
|
}
|
|
|
|
static void trm290_dma_start(ide_drive_t *drive)
|
|
{
|
|
}
|
|
|
|
static int trm290_dma_end(ide_drive_t *drive)
|
|
{
|
|
u16 status;
|
|
|
|
drive->waiting_for_dma = 0;
|
|
/* purge DMA mappings */
|
|
ide_destroy_dmatable(drive);
|
|
status = inw(HWIF(drive)->dma_base + 2);
|
|
return status != 0x00ff;
|
|
}
|
|
|
|
static int trm290_dma_test_irq(ide_drive_t *drive)
|
|
{
|
|
u16 status;
|
|
|
|
status = inw(HWIF(drive)->dma_base + 2);
|
|
return status == 0x00ff;
|
|
}
|
|
|
|
static void trm290_dma_host_set(ide_drive_t *drive, int on)
|
|
{
|
|
}
|
|
|
|
static void __devinit init_hwif_trm290(ide_hwif_t *hwif)
|
|
{
|
|
struct pci_dev *dev = to_pci_dev(hwif->dev);
|
|
unsigned int cfg_base = pci_resource_start(dev, 4);
|
|
unsigned long flags;
|
|
u8 reg = 0;
|
|
|
|
if ((dev->class & 5) && cfg_base)
|
|
printk(KERN_INFO "TRM290: chip");
|
|
else {
|
|
cfg_base = 0x3df0;
|
|
printk(KERN_INFO "TRM290: using default");
|
|
}
|
|
printk(KERN_CONT " config base at 0x%04x\n", cfg_base);
|
|
hwif->config_data = cfg_base;
|
|
hwif->dma_base = (cfg_base + 4) ^ (hwif->channel ? 0x80 : 0);
|
|
|
|
printk(KERN_INFO " %s: BM-DMA at 0x%04lx-0x%04lx\n",
|
|
hwif->name, hwif->dma_base, hwif->dma_base + 3);
|
|
|
|
if (ide_allocate_dma_engine(hwif))
|
|
return;
|
|
|
|
local_irq_save(flags);
|
|
/* put config reg into first byte of hwif->select_data */
|
|
outb(0x51 | (hwif->channel << 3), hwif->config_data + 1);
|
|
/* select PIO as default */
|
|
hwif->select_data = 0x21;
|
|
outb(hwif->select_data, hwif->config_data);
|
|
/* get IRQ info */
|
|
reg = inb(hwif->config_data + 3);
|
|
/* mask IRQs for both ports */
|
|
reg = (reg & 0x10) | 0x03;
|
|
outb(reg, hwif->config_data + 3);
|
|
local_irq_restore(flags);
|
|
|
|
if (reg & 0x10)
|
|
/* legacy mode */
|
|
hwif->irq = hwif->channel ? 15 : 14;
|
|
else if (!hwif->irq && hwif->mate && hwif->mate->irq)
|
|
/* sharing IRQ with mate */
|
|
hwif->irq = hwif->mate->irq;
|
|
|
|
#if 1
|
|
{
|
|
/*
|
|
* My trm290-based card doesn't seem to work with all possible values
|
|
* for the control basereg, so this kludge ensures that we use only
|
|
* values that are known to work. Ugh. -ml
|
|
*/
|
|
u16 new, old, compat = hwif->channel ? 0x374 : 0x3f4;
|
|
static u16 next_offset = 0;
|
|
u8 old_mask;
|
|
|
|
outb(0x54 | (hwif->channel << 3), hwif->config_data + 1);
|
|
old = inw(hwif->config_data);
|
|
old &= ~1;
|
|
old_mask = inb(old + 2);
|
|
if (old != compat && old_mask == 0xff) {
|
|
/* leave lower 10 bits untouched */
|
|
compat += (next_offset += 0x400);
|
|
hwif->io_ports.ctl_addr = compat + 2;
|
|
outw(compat | 1, hwif->config_data);
|
|
new = inw(hwif->config_data);
|
|
printk(KERN_INFO "%s: control basereg workaround: "
|
|
"old=0x%04x, new=0x%04x\n",
|
|
hwif->name, old, new & ~1);
|
|
}
|
|
}
|
|
#endif
|
|
}
|
|
|
|
static const struct ide_port_ops trm290_port_ops = {
|
|
.selectproc = trm290_selectproc,
|
|
};
|
|
|
|
static struct ide_dma_ops trm290_dma_ops = {
|
|
.dma_host_set = trm290_dma_host_set,
|
|
.dma_setup = trm290_dma_setup,
|
|
.dma_exec_cmd = trm290_dma_exec_cmd,
|
|
.dma_start = trm290_dma_start,
|
|
.dma_end = trm290_dma_end,
|
|
.dma_test_irq = trm290_dma_test_irq,
|
|
.dma_lost_irq = ide_dma_lost_irq,
|
|
.dma_timeout = ide_dma_timeout,
|
|
};
|
|
|
|
static const struct ide_port_info trm290_chipset __devinitdata = {
|
|
.name = "TRM290",
|
|
.init_hwif = init_hwif_trm290,
|
|
.chipset = ide_trm290,
|
|
.port_ops = &trm290_port_ops,
|
|
.dma_ops = &trm290_dma_ops,
|
|
.host_flags = IDE_HFLAG_NO_ATAPI_DMA |
|
|
#if 0 /* play it safe for now */
|
|
IDE_HFLAG_TRUST_BIOS_FOR_DMA |
|
|
#endif
|
|
IDE_HFLAG_NO_AUTODMA |
|
|
IDE_HFLAG_NO_LBA48,
|
|
};
|
|
|
|
static int __devinit trm290_init_one(struct pci_dev *dev, const struct pci_device_id *id)
|
|
{
|
|
return ide_setup_pci_device(dev, &trm290_chipset);
|
|
}
|
|
|
|
static const struct pci_device_id trm290_pci_tbl[] = {
|
|
{ PCI_VDEVICE(TEKRAM, PCI_DEVICE_ID_TEKRAM_DC290), 0 },
|
|
{ 0, },
|
|
};
|
|
MODULE_DEVICE_TABLE(pci, trm290_pci_tbl);
|
|
|
|
static struct pci_driver driver = {
|
|
.name = "TRM290_IDE",
|
|
.id_table = trm290_pci_tbl,
|
|
.probe = trm290_init_one,
|
|
};
|
|
|
|
static int __init trm290_ide_init(void)
|
|
{
|
|
return ide_pci_register_driver(&driver);
|
|
}
|
|
|
|
module_init(trm290_ide_init);
|
|
|
|
MODULE_AUTHOR("Mark Lord");
|
|
MODULE_DESCRIPTION("PCI driver module for Tekram TRM290 IDE");
|
|
MODULE_LICENSE("GPL");
|