652bcd8f72
Most of the omap1 MMC boards got broken by an earlier patch
138ab9f832. If you look closely,
the MMC init funtions are pretty much just stubs.
Remove broken init code to make room for cleaner MMC init code.
Cc: Pierre Ossman <drzeus-mmc@drzeus.cx>
Signed-off-by: Tony Lindgren <tony@atomide.com>
560 lines
13 KiB
C
560 lines
13 KiB
C
/*
|
|
* linux/arch/arm/mach-omap1/board-h3.c
|
|
*
|
|
* This file contains OMAP1710 H3 specific code.
|
|
*
|
|
* Copyright (C) 2004 Texas Instruments, Inc.
|
|
* Copyright (C) 2002 MontaVista Software, Inc.
|
|
* Copyright (C) 2001 RidgeRun, Inc.
|
|
* Author: RidgeRun, Inc.
|
|
* Greg Lonnon (glonnon@ridgerun.com) or info@ridgerun.com
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 as
|
|
* published by the Free Software Foundation.
|
|
*/
|
|
|
|
#include <linux/types.h>
|
|
#include <linux/init.h>
|
|
#include <linux/major.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/errno.h>
|
|
#include <linux/workqueue.h>
|
|
#include <linux/i2c.h>
|
|
#include <linux/mtd/mtd.h>
|
|
#include <linux/mtd/nand.h>
|
|
#include <linux/mtd/partitions.h>
|
|
#include <linux/input.h>
|
|
#include <linux/spi/spi.h>
|
|
#include <linux/i2c/tps65010.h>
|
|
|
|
#include <asm/setup.h>
|
|
#include <asm/page.h>
|
|
#include <mach/hardware.h>
|
|
#include <asm/gpio.h>
|
|
|
|
#include <asm/mach-types.h>
|
|
#include <asm/mach/arch.h>
|
|
#include <asm/mach/flash.h>
|
|
#include <asm/mach/map.h>
|
|
|
|
#include <mach/gpioexpander.h>
|
|
#include <mach/irqs.h>
|
|
#include <mach/mux.h>
|
|
#include <mach/tc.h>
|
|
#include <mach/nand.h>
|
|
#include <mach/irda.h>
|
|
#include <mach/usb.h>
|
|
#include <mach/keypad.h>
|
|
#include <mach/dma.h>
|
|
#include <mach/common.h>
|
|
#include <mach/mcbsp.h>
|
|
#include <mach/omap-alsa.h>
|
|
|
|
#define H3_TS_GPIO 48
|
|
|
|
static int h3_keymap[] = {
|
|
KEY(0, 0, KEY_LEFT),
|
|
KEY(0, 1, KEY_RIGHT),
|
|
KEY(0, 2, KEY_3),
|
|
KEY(0, 3, KEY_F10),
|
|
KEY(0, 4, KEY_F5),
|
|
KEY(0, 5, KEY_9),
|
|
KEY(1, 0, KEY_DOWN),
|
|
KEY(1, 1, KEY_UP),
|
|
KEY(1, 2, KEY_2),
|
|
KEY(1, 3, KEY_F9),
|
|
KEY(1, 4, KEY_F7),
|
|
KEY(1, 5, KEY_0),
|
|
KEY(2, 0, KEY_ENTER),
|
|
KEY(2, 1, KEY_6),
|
|
KEY(2, 2, KEY_1),
|
|
KEY(2, 3, KEY_F2),
|
|
KEY(2, 4, KEY_F6),
|
|
KEY(2, 5, KEY_HOME),
|
|
KEY(3, 0, KEY_8),
|
|
KEY(3, 1, KEY_5),
|
|
KEY(3, 2, KEY_F12),
|
|
KEY(3, 3, KEY_F3),
|
|
KEY(3, 4, KEY_F8),
|
|
KEY(3, 5, KEY_END),
|
|
KEY(4, 0, KEY_7),
|
|
KEY(4, 1, KEY_4),
|
|
KEY(4, 2, KEY_F11),
|
|
KEY(4, 3, KEY_F1),
|
|
KEY(4, 4, KEY_F4),
|
|
KEY(4, 5, KEY_ESC),
|
|
KEY(5, 0, KEY_F13),
|
|
KEY(5, 1, KEY_F14),
|
|
KEY(5, 2, KEY_F15),
|
|
KEY(5, 3, KEY_F16),
|
|
KEY(5, 4, KEY_SLEEP),
|
|
0
|
|
};
|
|
|
|
|
|
static struct mtd_partition nor_partitions[] = {
|
|
/* bootloader (U-Boot, etc) in first sector */
|
|
{
|
|
.name = "bootloader",
|
|
.offset = 0,
|
|
.size = SZ_128K,
|
|
.mask_flags = MTD_WRITEABLE, /* force read-only */
|
|
},
|
|
/* bootloader params in the next sector */
|
|
{
|
|
.name = "params",
|
|
.offset = MTDPART_OFS_APPEND,
|
|
.size = SZ_128K,
|
|
.mask_flags = 0,
|
|
},
|
|
/* kernel */
|
|
{
|
|
.name = "kernel",
|
|
.offset = MTDPART_OFS_APPEND,
|
|
.size = SZ_2M,
|
|
.mask_flags = 0
|
|
},
|
|
/* file system */
|
|
{
|
|
.name = "filesystem",
|
|
.offset = MTDPART_OFS_APPEND,
|
|
.size = MTDPART_SIZ_FULL,
|
|
.mask_flags = 0
|
|
}
|
|
};
|
|
|
|
static struct flash_platform_data nor_data = {
|
|
.map_name = "cfi_probe",
|
|
.width = 2,
|
|
.parts = nor_partitions,
|
|
.nr_parts = ARRAY_SIZE(nor_partitions),
|
|
};
|
|
|
|
static struct resource nor_resource = {
|
|
/* This is on CS3, wherever it's mapped */
|
|
.flags = IORESOURCE_MEM,
|
|
};
|
|
|
|
static struct platform_device nor_device = {
|
|
.name = "omapflash",
|
|
.id = 0,
|
|
.dev = {
|
|
.platform_data = &nor_data,
|
|
},
|
|
.num_resources = 1,
|
|
.resource = &nor_resource,
|
|
};
|
|
|
|
static struct mtd_partition nand_partitions[] = {
|
|
#if 0
|
|
/* REVISIT: enable these partitions if you make NAND BOOT work */
|
|
{
|
|
.name = "xloader",
|
|
.offset = 0,
|
|
.size = 64 * 1024,
|
|
.mask_flags = MTD_WRITEABLE, /* force read-only */
|
|
},
|
|
{
|
|
.name = "bootloader",
|
|
.offset = MTDPART_OFS_APPEND,
|
|
.size = 256 * 1024,
|
|
.mask_flags = MTD_WRITEABLE, /* force read-only */
|
|
},
|
|
{
|
|
.name = "params",
|
|
.offset = MTDPART_OFS_APPEND,
|
|
.size = 192 * 1024,
|
|
},
|
|
{
|
|
.name = "kernel",
|
|
.offset = MTDPART_OFS_APPEND,
|
|
.size = 2 * SZ_1M,
|
|
},
|
|
#endif
|
|
{
|
|
.name = "filesystem",
|
|
.size = MTDPART_SIZ_FULL,
|
|
.offset = MTDPART_OFS_APPEND,
|
|
},
|
|
};
|
|
|
|
/* dip switches control NAND chip access: 8 bit, 16 bit, or neither */
|
|
static struct omap_nand_platform_data nand_data = {
|
|
.options = NAND_SAMSUNG_LP_OPTIONS,
|
|
.parts = nand_partitions,
|
|
.nr_parts = ARRAY_SIZE(nand_partitions),
|
|
};
|
|
|
|
static struct resource nand_resource = {
|
|
.flags = IORESOURCE_MEM,
|
|
};
|
|
|
|
static struct platform_device nand_device = {
|
|
.name = "omapnand",
|
|
.id = 0,
|
|
.dev = {
|
|
.platform_data = &nand_data,
|
|
},
|
|
.num_resources = 1,
|
|
.resource = &nand_resource,
|
|
};
|
|
|
|
static struct resource smc91x_resources[] = {
|
|
[0] = {
|
|
.start = OMAP1710_ETHR_START, /* Physical */
|
|
.end = OMAP1710_ETHR_START + 0xf,
|
|
.flags = IORESOURCE_MEM,
|
|
},
|
|
[1] = {
|
|
.start = OMAP_GPIO_IRQ(40),
|
|
.end = OMAP_GPIO_IRQ(40),
|
|
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
|
|
},
|
|
};
|
|
|
|
static struct platform_device smc91x_device = {
|
|
.name = "smc91x",
|
|
.id = 0,
|
|
.num_resources = ARRAY_SIZE(smc91x_resources),
|
|
.resource = smc91x_resources,
|
|
};
|
|
|
|
#define GPTIMER_BASE 0xFFFB1400
|
|
#define GPTIMER_REGS(x) (0xFFFB1400 + (x * 0x800))
|
|
#define GPTIMER_REGS_SIZE 0x46
|
|
|
|
static struct resource intlat_resources[] = {
|
|
[0] = {
|
|
.start = GPTIMER_REGS(0), /* Physical */
|
|
.end = GPTIMER_REGS(0) + GPTIMER_REGS_SIZE,
|
|
.flags = IORESOURCE_MEM,
|
|
},
|
|
[1] = {
|
|
.start = INT_1610_GPTIMER1,
|
|
.end = INT_1610_GPTIMER1,
|
|
.flags = IORESOURCE_IRQ,
|
|
},
|
|
};
|
|
|
|
static struct platform_device intlat_device = {
|
|
.name = "omap_intlat",
|
|
.id = 0,
|
|
.num_resources = ARRAY_SIZE(intlat_resources),
|
|
.resource = intlat_resources,
|
|
};
|
|
|
|
static struct resource h3_kp_resources[] = {
|
|
[0] = {
|
|
.start = INT_KEYBOARD,
|
|
.end = INT_KEYBOARD,
|
|
.flags = IORESOURCE_IRQ,
|
|
},
|
|
};
|
|
|
|
static struct omap_kp_platform_data h3_kp_data = {
|
|
.rows = 8,
|
|
.cols = 8,
|
|
.keymap = h3_keymap,
|
|
.keymapsize = ARRAY_SIZE(h3_keymap),
|
|
.rep = 1,
|
|
.delay = 9,
|
|
.dbounce = 1,
|
|
};
|
|
|
|
static struct platform_device h3_kp_device = {
|
|
.name = "omap-keypad",
|
|
.id = -1,
|
|
.dev = {
|
|
.platform_data = &h3_kp_data,
|
|
},
|
|
.num_resources = ARRAY_SIZE(h3_kp_resources),
|
|
.resource = h3_kp_resources,
|
|
};
|
|
|
|
|
|
/* Select between the IrDA and aGPS module
|
|
*/
|
|
static int h3_select_irda(struct device *dev, int state)
|
|
{
|
|
unsigned char expa;
|
|
int err = 0;
|
|
|
|
if ((err = read_gpio_expa(&expa, 0x26))) {
|
|
printk(KERN_ERR "Error reading from I/O EXPANDER \n");
|
|
return err;
|
|
}
|
|
|
|
/* 'P6' enable/disable IRDA_TX and IRDA_RX */
|
|
if (state & IR_SEL) { /* IrDA */
|
|
if ((err = write_gpio_expa(expa | 0x40, 0x26))) {
|
|
printk(KERN_ERR "Error writing to I/O EXPANDER \n");
|
|
return err;
|
|
}
|
|
} else {
|
|
if ((err = write_gpio_expa(expa & ~0x40, 0x26))) {
|
|
printk(KERN_ERR "Error writing to I/O EXPANDER \n");
|
|
return err;
|
|
}
|
|
}
|
|
return err;
|
|
}
|
|
|
|
static void set_trans_mode(struct work_struct *work)
|
|
{
|
|
struct omap_irda_config *irda_config =
|
|
container_of(work, struct omap_irda_config, gpio_expa.work);
|
|
int mode = irda_config->mode;
|
|
unsigned char expa;
|
|
int err = 0;
|
|
|
|
if ((err = read_gpio_expa(&expa, 0x27)) != 0) {
|
|
printk(KERN_ERR "Error reading from I/O expander\n");
|
|
}
|
|
|
|
expa &= ~0x03;
|
|
|
|
if (mode & IR_SIRMODE) {
|
|
expa |= 0x01;
|
|
} else { /* MIR/FIR */
|
|
expa |= 0x03;
|
|
}
|
|
|
|
if ((err = write_gpio_expa(expa, 0x27)) != 0) {
|
|
printk(KERN_ERR "Error writing to I/O expander\n");
|
|
}
|
|
}
|
|
|
|
static int h3_transceiver_mode(struct device *dev, int mode)
|
|
{
|
|
struct omap_irda_config *irda_config = dev->platform_data;
|
|
|
|
irda_config->mode = mode;
|
|
cancel_delayed_work(&irda_config->gpio_expa);
|
|
PREPARE_DELAYED_WORK(&irda_config->gpio_expa, set_trans_mode);
|
|
schedule_delayed_work(&irda_config->gpio_expa, 0);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static struct omap_irda_config h3_irda_data = {
|
|
.transceiver_cap = IR_SIRMODE | IR_MIRMODE | IR_FIRMODE,
|
|
.transceiver_mode = h3_transceiver_mode,
|
|
.select_irda = h3_select_irda,
|
|
.rx_channel = OMAP_DMA_UART3_RX,
|
|
.tx_channel = OMAP_DMA_UART3_TX,
|
|
.dest_start = UART3_THR,
|
|
.src_start = UART3_RHR,
|
|
.tx_trigger = 0,
|
|
.rx_trigger = 0,
|
|
};
|
|
|
|
static struct resource h3_irda_resources[] = {
|
|
[0] = {
|
|
.start = INT_UART3,
|
|
.end = INT_UART3,
|
|
.flags = IORESOURCE_IRQ,
|
|
},
|
|
};
|
|
|
|
static u64 irda_dmamask = 0xffffffff;
|
|
|
|
static struct platform_device h3_irda_device = {
|
|
.name = "omapirda",
|
|
.id = 0,
|
|
.dev = {
|
|
.platform_data = &h3_irda_data,
|
|
.dma_mask = &irda_dmamask,
|
|
},
|
|
.num_resources = ARRAY_SIZE(h3_irda_resources),
|
|
.resource = h3_irda_resources,
|
|
};
|
|
|
|
static struct platform_device h3_lcd_device = {
|
|
.name = "lcd_h3",
|
|
.id = -1,
|
|
};
|
|
|
|
static struct spi_board_info h3_spi_board_info[] __initdata = {
|
|
[0] = {
|
|
.modalias = "tsc2101",
|
|
.bus_num = 2,
|
|
.chip_select = 0,
|
|
.irq = OMAP_GPIO_IRQ(H3_TS_GPIO),
|
|
.max_speed_hz = 16000000,
|
|
/* .platform_data = &tsc_platform_data, */
|
|
},
|
|
};
|
|
|
|
static struct omap_mcbsp_reg_cfg mcbsp_regs = {
|
|
.spcr2 = FREE | FRST | GRST | XRST | XINTM(3),
|
|
.spcr1 = RINTM(3) | RRST,
|
|
.rcr2 = RPHASE | RFRLEN2(OMAP_MCBSP_WORD_8) |
|
|
RWDLEN2(OMAP_MCBSP_WORD_16) | RDATDLY(1),
|
|
.rcr1 = RFRLEN1(OMAP_MCBSP_WORD_8) | RWDLEN1(OMAP_MCBSP_WORD_16),
|
|
.xcr2 = XPHASE | XFRLEN2(OMAP_MCBSP_WORD_8) |
|
|
XWDLEN2(OMAP_MCBSP_WORD_16) | XDATDLY(1) | XFIG,
|
|
.xcr1 = XFRLEN1(OMAP_MCBSP_WORD_8) | XWDLEN1(OMAP_MCBSP_WORD_16),
|
|
.srgr1 = FWID(15),
|
|
.srgr2 = GSYNC | CLKSP | FSGM | FPER(31),
|
|
|
|
.pcr0 = CLKRM | SCLKME | FSXP | FSRP | CLKXP | CLKRP,
|
|
/*.pcr0 = CLKXP | CLKRP,*/ /* mcbsp: slave */
|
|
};
|
|
|
|
static struct omap_alsa_codec_config alsa_config = {
|
|
.name = "H3 TSC2101",
|
|
.mcbsp_regs_alsa = &mcbsp_regs,
|
|
.codec_configure_dev = NULL, /* tsc2101_configure, */
|
|
.codec_set_samplerate = NULL, /* tsc2101_set_samplerate, */
|
|
.codec_clock_setup = NULL, /* tsc2101_clock_setup, */
|
|
.codec_clock_on = NULL, /* tsc2101_clock_on, */
|
|
.codec_clock_off = NULL, /* tsc2101_clock_off, */
|
|
.get_default_samplerate = NULL, /* tsc2101_get_default_samplerate, */
|
|
};
|
|
|
|
static struct platform_device h3_mcbsp1_device = {
|
|
.name = "omap_alsa_mcbsp",
|
|
.id = 1,
|
|
.dev = {
|
|
.platform_data = &alsa_config,
|
|
},
|
|
};
|
|
|
|
static struct platform_device *devices[] __initdata = {
|
|
&nor_device,
|
|
&nand_device,
|
|
&smc91x_device,
|
|
&intlat_device,
|
|
&h3_irda_device,
|
|
&h3_kp_device,
|
|
&h3_lcd_device,
|
|
&h3_mcbsp1_device,
|
|
};
|
|
|
|
static struct omap_usb_config h3_usb_config __initdata = {
|
|
/* usb1 has a Mini-AB port and external isp1301 transceiver */
|
|
.otg = 2,
|
|
|
|
#ifdef CONFIG_USB_GADGET_OMAP
|
|
.hmc_mode = 19, /* 0:host(off) 1:dev|otg 2:disabled */
|
|
#elif defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
|
|
/* NONSTANDARD CABLE NEEDED (B-to-Mini-B) */
|
|
.hmc_mode = 20, /* 1:dev|otg(off) 1:host 2:disabled */
|
|
#endif
|
|
|
|
.pins[1] = 3,
|
|
};
|
|
|
|
static struct omap_uart_config h3_uart_config __initdata = {
|
|
.enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
|
|
};
|
|
|
|
static struct omap_lcd_config h3_lcd_config __initdata = {
|
|
.ctrl_name = "internal",
|
|
};
|
|
|
|
static struct omap_board_config_kernel h3_config[] __initdata = {
|
|
{ OMAP_TAG_USB, &h3_usb_config },
|
|
{ OMAP_TAG_UART, &h3_uart_config },
|
|
{ OMAP_TAG_LCD, &h3_lcd_config },
|
|
};
|
|
|
|
static struct i2c_board_info __initdata h3_i2c_board_info[] = {
|
|
{
|
|
I2C_BOARD_INFO("tps65013", 0x48),
|
|
/* .irq = OMAP_GPIO_IRQ(??), */
|
|
},
|
|
{
|
|
I2C_BOARD_INFO("isp1301_omap", 0x2d),
|
|
.irq = OMAP_GPIO_IRQ(14),
|
|
},
|
|
};
|
|
|
|
static struct omap_gpio_switch h3_gpio_switches[] __initdata = {
|
|
{
|
|
.name = "mmc_slot",
|
|
.gpio = OMAP_MPUIO(1),
|
|
.type = OMAP_GPIO_SWITCH_TYPE_COVER,
|
|
.debounce_rising = 100,
|
|
.debounce_falling = 0,
|
|
.notify = h3_mmc_slot_cover_handler,
|
|
.notify_data = NULL,
|
|
},
|
|
};
|
|
|
|
#define H3_NAND_RB_GPIO_PIN 10
|
|
|
|
static int nand_dev_ready(struct omap_nand_platform_data *data)
|
|
{
|
|
return gpio_get_value(H3_NAND_RB_GPIO_PIN);
|
|
}
|
|
|
|
static void __init h3_init(void)
|
|
{
|
|
/* Here we assume the NOR boot config: NOR on CS3 (possibly swapped
|
|
* to address 0 by a dip switch), NAND on CS2B. The NAND driver will
|
|
* notice whether a NAND chip is enabled at probe time.
|
|
*
|
|
* H3 support NAND-boot, with a dip switch to put NOR on CS2B and NAND
|
|
* (which on H2 may be 16bit) on CS3. Try detecting that in code here,
|
|
* to avoid probing every possible flash configuration...
|
|
*/
|
|
nor_resource.end = nor_resource.start = omap_cs3_phys();
|
|
nor_resource.end += SZ_32M - 1;
|
|
|
|
nand_resource.end = nand_resource.start = OMAP_CS2B_PHYS;
|
|
nand_resource.end += SZ_4K - 1;
|
|
if (gpio_request(H3_NAND_RB_GPIO_PIN, "NAND ready") < 0)
|
|
BUG();
|
|
nand_data.dev_ready = nand_dev_ready;
|
|
|
|
/* GPIO10 Func_MUX_CTRL reg bit 29:27, Configure V2 to mode1 as GPIO */
|
|
/* GPIO10 pullup/down register, Enable pullup on GPIO10 */
|
|
omap_cfg_reg(V2_1710_GPIO10);
|
|
|
|
platform_add_devices(devices, ARRAY_SIZE(devices));
|
|
spi_register_board_info(h3_spi_board_info,
|
|
ARRAY_SIZE(h3_spi_board_info));
|
|
omap_board_config = h3_config;
|
|
omap_board_config_size = ARRAY_SIZE(h3_config);
|
|
omap_serial_init();
|
|
omap_register_i2c_bus(1, 100, h3_i2c_board_info,
|
|
ARRAY_SIZE(h3_i2c_board_info));
|
|
h3_mmc_init();
|
|
}
|
|
|
|
static void __init h3_init_smc91x(void)
|
|
{
|
|
omap_cfg_reg(W15_1710_GPIO40);
|
|
if (gpio_request(40, "SMC91x irq") < 0) {
|
|
printk("Error requesting gpio 40 for smc91x irq\n");
|
|
return;
|
|
}
|
|
}
|
|
|
|
static void __init h3_init_irq(void)
|
|
{
|
|
omap1_init_common_hw();
|
|
omap_init_irq();
|
|
omap_gpio_init();
|
|
h3_init_smc91x();
|
|
}
|
|
|
|
static void __init h3_map_io(void)
|
|
{
|
|
omap1_map_common_io();
|
|
}
|
|
|
|
MACHINE_START(OMAP_H3, "TI OMAP1710 H3 board")
|
|
/* Maintainer: Texas Instruments, Inc. */
|
|
.phys_io = 0xfff00000,
|
|
.io_pg_offst = ((0xfef00000) >> 18) & 0xfffc,
|
|
.boot_params = 0x10000100,
|
|
.map_io = h3_map_io,
|
|
.init_irq = h3_init_irq,
|
|
.init_machine = h3_init,
|
|
.timer = &omap_timer,
|
|
MACHINE_END
|