![Tony Lindgren](/assets/img/avatar_default.png)
This will simplify the MMC low-level init, and make it more flexible to add support for a newer MMC controller in the following patches. The patch rearranges platform data and gets rid of slot vs controller confusion in the old data structures. Also fix device id numbering in the clock code. Some code snippets are based on an earlier patch by Russell King <linux@arm.linux.org.uk>. Cc: Pierre Ossman <drzeus-mmc@drzeus.cx> Signed-off-by: Tony Lindgren <tony@atomide.com>
477 lines
12 KiB
C
477 lines
12 KiB
C
/*
|
|
* linux/arch/arm/mach-omap1/board-h2.c
|
|
*
|
|
* Board specific inits for OMAP-1610 H2
|
|
*
|
|
* Copyright (C) 2001 RidgeRun, Inc.
|
|
* Author: Greg Lonnon <glonnon@ridgerun.com>
|
|
*
|
|
* Copyright (C) 2002 MontaVista Software, Inc.
|
|
*
|
|
* Separated FPGA interrupts from innovator1510.c and cleaned up for 2.6
|
|
* Copyright (C) 2004 Nokia Corporation by Tony Lindrgen <tony@atomide.com>
|
|
*
|
|
* H2 specific changes and cleanup
|
|
* Copyright (C) 2004 Nokia Corporation by Imre Deak <imre.deak@nokia.com>
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 as
|
|
* published by the Free Software Foundation.
|
|
*/
|
|
|
|
#include <linux/kernel.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/i2c.h>
|
|
#include <linux/mtd/mtd.h>
|
|
#include <linux/mtd/nand.h>
|
|
#include <linux/mtd/partitions.h>
|
|
#include <linux/input.h>
|
|
#include <linux/i2c/tps65010.h>
|
|
|
|
#include <mach/hardware.h>
|
|
#include <asm/gpio.h>
|
|
|
|
#include <asm/mach-types.h>
|
|
#include <asm/mach/arch.h>
|
|
#include <asm/mach/flash.h>
|
|
#include <asm/mach/map.h>
|
|
|
|
#include <mach/gpio-switch.h>
|
|
#include <mach/mux.h>
|
|
#include <mach/tc.h>
|
|
#include <mach/nand.h>
|
|
#include <mach/irda.h>
|
|
#include <mach/usb.h>
|
|
#include <mach/keypad.h>
|
|
#include <mach/common.h>
|
|
#include <mach/mcbsp.h>
|
|
#include <mach/omap-alsa.h>
|
|
|
|
static int h2_keymap[] = {
|
|
KEY(0, 0, KEY_LEFT),
|
|
KEY(0, 1, KEY_RIGHT),
|
|
KEY(0, 2, KEY_3),
|
|
KEY(0, 3, KEY_F10),
|
|
KEY(0, 4, KEY_F5),
|
|
KEY(0, 5, KEY_9),
|
|
KEY(1, 0, KEY_DOWN),
|
|
KEY(1, 1, KEY_UP),
|
|
KEY(1, 2, KEY_2),
|
|
KEY(1, 3, KEY_F9),
|
|
KEY(1, 4, KEY_F7),
|
|
KEY(1, 5, KEY_0),
|
|
KEY(2, 0, KEY_ENTER),
|
|
KEY(2, 1, KEY_6),
|
|
KEY(2, 2, KEY_1),
|
|
KEY(2, 3, KEY_F2),
|
|
KEY(2, 4, KEY_F6),
|
|
KEY(2, 5, KEY_HOME),
|
|
KEY(3, 0, KEY_8),
|
|
KEY(3, 1, KEY_5),
|
|
KEY(3, 2, KEY_F12),
|
|
KEY(3, 3, KEY_F3),
|
|
KEY(3, 4, KEY_F8),
|
|
KEY(3, 5, KEY_END),
|
|
KEY(4, 0, KEY_7),
|
|
KEY(4, 1, KEY_4),
|
|
KEY(4, 2, KEY_F11),
|
|
KEY(4, 3, KEY_F1),
|
|
KEY(4, 4, KEY_F4),
|
|
KEY(4, 5, KEY_ESC),
|
|
KEY(5, 0, KEY_F13),
|
|
KEY(5, 1, KEY_F14),
|
|
KEY(5, 2, KEY_F15),
|
|
KEY(5, 3, KEY_F16),
|
|
KEY(5, 4, KEY_SLEEP),
|
|
0
|
|
};
|
|
|
|
static struct mtd_partition h2_nor_partitions[] = {
|
|
/* bootloader (U-Boot, etc) in first sector */
|
|
{
|
|
.name = "bootloader",
|
|
.offset = 0,
|
|
.size = SZ_128K,
|
|
.mask_flags = MTD_WRITEABLE, /* force read-only */
|
|
},
|
|
/* bootloader params in the next sector */
|
|
{
|
|
.name = "params",
|
|
.offset = MTDPART_OFS_APPEND,
|
|
.size = SZ_128K,
|
|
.mask_flags = 0,
|
|
},
|
|
/* kernel */
|
|
{
|
|
.name = "kernel",
|
|
.offset = MTDPART_OFS_APPEND,
|
|
.size = SZ_2M,
|
|
.mask_flags = 0
|
|
},
|
|
/* file system */
|
|
{
|
|
.name = "filesystem",
|
|
.offset = MTDPART_OFS_APPEND,
|
|
.size = MTDPART_SIZ_FULL,
|
|
.mask_flags = 0
|
|
}
|
|
};
|
|
|
|
static struct flash_platform_data h2_nor_data = {
|
|
.map_name = "cfi_probe",
|
|
.width = 2,
|
|
.parts = h2_nor_partitions,
|
|
.nr_parts = ARRAY_SIZE(h2_nor_partitions),
|
|
};
|
|
|
|
static struct resource h2_nor_resource = {
|
|
/* This is on CS3, wherever it's mapped */
|
|
.flags = IORESOURCE_MEM,
|
|
};
|
|
|
|
static struct platform_device h2_nor_device = {
|
|
.name = "omapflash",
|
|
.id = 0,
|
|
.dev = {
|
|
.platform_data = &h2_nor_data,
|
|
},
|
|
.num_resources = 1,
|
|
.resource = &h2_nor_resource,
|
|
};
|
|
|
|
static struct mtd_partition h2_nand_partitions[] = {
|
|
#if 0
|
|
/* REVISIT: enable these partitions if you make NAND BOOT
|
|
* work on your H2 (rev C or newer); published versions of
|
|
* x-load only support P2 and H3.
|
|
*/
|
|
{
|
|
.name = "xloader",
|
|
.offset = 0,
|
|
.size = 64 * 1024,
|
|
.mask_flags = MTD_WRITEABLE, /* force read-only */
|
|
},
|
|
{
|
|
.name = "bootloader",
|
|
.offset = MTDPART_OFS_APPEND,
|
|
.size = 256 * 1024,
|
|
.mask_flags = MTD_WRITEABLE, /* force read-only */
|
|
},
|
|
{
|
|
.name = "params",
|
|
.offset = MTDPART_OFS_APPEND,
|
|
.size = 192 * 1024,
|
|
},
|
|
{
|
|
.name = "kernel",
|
|
.offset = MTDPART_OFS_APPEND,
|
|
.size = 2 * SZ_1M,
|
|
},
|
|
#endif
|
|
{
|
|
.name = "filesystem",
|
|
.size = MTDPART_SIZ_FULL,
|
|
.offset = MTDPART_OFS_APPEND,
|
|
},
|
|
};
|
|
|
|
/* dip switches control NAND chip access: 8 bit, 16 bit, or neither */
|
|
static struct omap_nand_platform_data h2_nand_data = {
|
|
.options = NAND_SAMSUNG_LP_OPTIONS,
|
|
.parts = h2_nand_partitions,
|
|
.nr_parts = ARRAY_SIZE(h2_nand_partitions),
|
|
};
|
|
|
|
static struct resource h2_nand_resource = {
|
|
.flags = IORESOURCE_MEM,
|
|
};
|
|
|
|
static struct platform_device h2_nand_device = {
|
|
.name = "omapnand",
|
|
.id = 0,
|
|
.dev = {
|
|
.platform_data = &h2_nand_data,
|
|
},
|
|
.num_resources = 1,
|
|
.resource = &h2_nand_resource,
|
|
};
|
|
|
|
static struct resource h2_smc91x_resources[] = {
|
|
[0] = {
|
|
.start = OMAP1610_ETHR_START, /* Physical */
|
|
.end = OMAP1610_ETHR_START + 0xf,
|
|
.flags = IORESOURCE_MEM,
|
|
},
|
|
[1] = {
|
|
.start = OMAP_GPIO_IRQ(0),
|
|
.end = OMAP_GPIO_IRQ(0),
|
|
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
|
|
},
|
|
};
|
|
|
|
static struct platform_device h2_smc91x_device = {
|
|
.name = "smc91x",
|
|
.id = 0,
|
|
.num_resources = ARRAY_SIZE(h2_smc91x_resources),
|
|
.resource = h2_smc91x_resources,
|
|
};
|
|
|
|
static struct resource h2_kp_resources[] = {
|
|
[0] = {
|
|
.start = INT_KEYBOARD,
|
|
.end = INT_KEYBOARD,
|
|
.flags = IORESOURCE_IRQ,
|
|
},
|
|
};
|
|
|
|
static struct omap_kp_platform_data h2_kp_data = {
|
|
.rows = 8,
|
|
.cols = 8,
|
|
.keymap = h2_keymap,
|
|
.keymapsize = ARRAY_SIZE(h2_keymap),
|
|
.rep = 1,
|
|
.delay = 9,
|
|
.dbounce = 1,
|
|
};
|
|
|
|
static struct platform_device h2_kp_device = {
|
|
.name = "omap-keypad",
|
|
.id = -1,
|
|
.dev = {
|
|
.platform_data = &h2_kp_data,
|
|
},
|
|
.num_resources = ARRAY_SIZE(h2_kp_resources),
|
|
.resource = h2_kp_resources,
|
|
};
|
|
|
|
#define H2_IRDA_FIRSEL_GPIO_PIN 17
|
|
|
|
#if defined(CONFIG_OMAP_IR) || defined(CONFIG_OMAP_IR_MODULE)
|
|
static int h2_transceiver_mode(struct device *dev, int state)
|
|
{
|
|
/* SIR when low, else MIR/FIR when HIGH */
|
|
gpio_set_value(H2_IRDA_FIRSEL_GPIO_PIN, !(state & IR_SIRMODE));
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
static struct omap_irda_config h2_irda_data = {
|
|
.transceiver_cap = IR_SIRMODE | IR_MIRMODE | IR_FIRMODE,
|
|
.rx_channel = OMAP_DMA_UART3_RX,
|
|
.tx_channel = OMAP_DMA_UART3_TX,
|
|
.dest_start = UART3_THR,
|
|
.src_start = UART3_RHR,
|
|
.tx_trigger = 0,
|
|
.rx_trigger = 0,
|
|
};
|
|
|
|
static struct resource h2_irda_resources[] = {
|
|
[0] = {
|
|
.start = INT_UART3,
|
|
.end = INT_UART3,
|
|
.flags = IORESOURCE_IRQ,
|
|
},
|
|
};
|
|
|
|
static u64 irda_dmamask = 0xffffffff;
|
|
|
|
static struct platform_device h2_irda_device = {
|
|
.name = "omapirda",
|
|
.id = 0,
|
|
.dev = {
|
|
.platform_data = &h2_irda_data,
|
|
.dma_mask = &irda_dmamask,
|
|
},
|
|
.num_resources = ARRAY_SIZE(h2_irda_resources),
|
|
.resource = h2_irda_resources,
|
|
};
|
|
|
|
static struct platform_device h2_lcd_device = {
|
|
.name = "lcd_h2",
|
|
.id = -1,
|
|
};
|
|
|
|
static struct omap_mcbsp_reg_cfg mcbsp_regs = {
|
|
.spcr2 = FREE | FRST | GRST | XRST | XINTM(3),
|
|
.spcr1 = RINTM(3) | RRST,
|
|
.rcr2 = RPHASE | RFRLEN2(OMAP_MCBSP_WORD_8) |
|
|
RWDLEN2(OMAP_MCBSP_WORD_16) | RDATDLY(1),
|
|
.rcr1 = RFRLEN1(OMAP_MCBSP_WORD_8) | RWDLEN1(OMAP_MCBSP_WORD_16),
|
|
.xcr2 = XPHASE | XFRLEN2(OMAP_MCBSP_WORD_8) |
|
|
XWDLEN2(OMAP_MCBSP_WORD_16) | XDATDLY(1) | XFIG,
|
|
.xcr1 = XFRLEN1(OMAP_MCBSP_WORD_8) | XWDLEN1(OMAP_MCBSP_WORD_16),
|
|
.srgr1 = FWID(15),
|
|
.srgr2 = GSYNC | CLKSP | FSGM | FPER(31),
|
|
|
|
.pcr0 = CLKXM | CLKRM | FSXP | FSRP | CLKXP | CLKRP,
|
|
/*.pcr0 = CLKXP | CLKRP,*/ /* mcbsp: slave */
|
|
};
|
|
|
|
static struct omap_alsa_codec_config alsa_config = {
|
|
.name = "H2 TSC2101",
|
|
.mcbsp_regs_alsa = &mcbsp_regs,
|
|
.codec_configure_dev = NULL, /* tsc2101_configure, */
|
|
.codec_set_samplerate = NULL, /* tsc2101_set_samplerate, */
|
|
.codec_clock_setup = NULL, /* tsc2101_clock_setup, */
|
|
.codec_clock_on = NULL, /* tsc2101_clock_on, */
|
|
.codec_clock_off = NULL, /* tsc2101_clock_off, */
|
|
.get_default_samplerate = NULL, /* tsc2101_get_default_samplerate, */
|
|
};
|
|
|
|
static struct platform_device h2_mcbsp1_device = {
|
|
.name = "omap_alsa_mcbsp",
|
|
.id = 1,
|
|
.dev = {
|
|
.platform_data = &alsa_config,
|
|
},
|
|
};
|
|
|
|
static struct platform_device *h2_devices[] __initdata = {
|
|
&h2_nor_device,
|
|
&h2_nand_device,
|
|
&h2_smc91x_device,
|
|
&h2_irda_device,
|
|
&h2_kp_device,
|
|
&h2_lcd_device,
|
|
&h2_mcbsp1_device,
|
|
};
|
|
|
|
static void __init h2_init_smc91x(void)
|
|
{
|
|
if (gpio_request(0, "SMC91x irq") < 0) {
|
|
printk("Error requesting gpio 0 for smc91x irq\n");
|
|
return;
|
|
}
|
|
}
|
|
|
|
static int tps_setup(struct i2c_client *client, void *context)
|
|
{
|
|
tps65010_config_vregs1(TPS_LDO2_ENABLE | TPS_VLDO2_3_0V |
|
|
TPS_LDO1_ENABLE | TPS_VLDO1_3_0V);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static struct tps65010_board tps_board = {
|
|
.base = H2_TPS_GPIO_BASE,
|
|
.outmask = 0x0f,
|
|
.setup = tps_setup,
|
|
};
|
|
|
|
static struct i2c_board_info __initdata h2_i2c_board_info[] = {
|
|
{
|
|
I2C_BOARD_INFO("tps65010", 0x48),
|
|
.irq = OMAP_GPIO_IRQ(58),
|
|
.platform_data = &tps_board,
|
|
}, {
|
|
I2C_BOARD_INFO("isp1301_omap", 0x2d),
|
|
.irq = OMAP_GPIO_IRQ(2),
|
|
},
|
|
};
|
|
|
|
static void __init h2_init_irq(void)
|
|
{
|
|
omap1_init_common_hw();
|
|
omap_init_irq();
|
|
omap_gpio_init();
|
|
h2_init_smc91x();
|
|
}
|
|
|
|
static struct omap_usb_config h2_usb_config __initdata = {
|
|
/* usb1 has a Mini-AB port and external isp1301 transceiver */
|
|
.otg = 2,
|
|
|
|
#ifdef CONFIG_USB_GADGET_OMAP
|
|
.hmc_mode = 19, /* 0:host(off) 1:dev|otg 2:disabled */
|
|
/* .hmc_mode = 21,*/ /* 0:host(off) 1:dev(loopback) 2:host(loopback) */
|
|
#elif defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
|
|
/* needs OTG cable, or NONSTANDARD (B-to-MiniB) */
|
|
.hmc_mode = 20, /* 1:dev|otg(off) 1:host 2:disabled */
|
|
#endif
|
|
|
|
.pins[1] = 3,
|
|
};
|
|
|
|
static struct omap_uart_config h2_uart_config __initdata = {
|
|
.enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
|
|
};
|
|
|
|
static struct omap_lcd_config h2_lcd_config __initdata = {
|
|
.ctrl_name = "internal",
|
|
};
|
|
|
|
static struct omap_board_config_kernel h2_config[] __initdata = {
|
|
{ OMAP_TAG_USB, &h2_usb_config },
|
|
{ OMAP_TAG_UART, &h2_uart_config },
|
|
{ OMAP_TAG_LCD, &h2_lcd_config },
|
|
};
|
|
|
|
#define H2_NAND_RB_GPIO_PIN 62
|
|
|
|
static int h2_nand_dev_ready(struct omap_nand_platform_data *data)
|
|
{
|
|
return gpio_get_value(H2_NAND_RB_GPIO_PIN);
|
|
}
|
|
|
|
static void __init h2_init(void)
|
|
{
|
|
/* Here we assume the NOR boot config: NOR on CS3 (possibly swapped
|
|
* to address 0 by a dip switch), NAND on CS2B. The NAND driver will
|
|
* notice whether a NAND chip is enabled at probe time.
|
|
*
|
|
* FIXME revC boards (and H3) support NAND-boot, with a dip switch to
|
|
* put NOR on CS2B and NAND (which on H2 may be 16bit) on CS3. Try
|
|
* detecting that in code here, to avoid probing every possible flash
|
|
* configuration...
|
|
*/
|
|
h2_nor_resource.end = h2_nor_resource.start = omap_cs3_phys();
|
|
h2_nor_resource.end += SZ_32M - 1;
|
|
|
|
h2_nand_resource.end = h2_nand_resource.start = OMAP_CS2B_PHYS;
|
|
h2_nand_resource.end += SZ_4K - 1;
|
|
if (gpio_request(H2_NAND_RB_GPIO_PIN, "NAND ready") < 0)
|
|
BUG();
|
|
gpio_direction_input(H2_NAND_RB_GPIO_PIN);
|
|
|
|
omap_cfg_reg(L3_1610_FLASH_CS2B_OE);
|
|
omap_cfg_reg(M8_1610_FLASH_CS2B_WE);
|
|
|
|
/* MMC: card detect and WP */
|
|
/* omap_cfg_reg(U19_ARMIO1); */ /* CD */
|
|
omap_cfg_reg(BALLOUT_V8_ARMIO3); /* WP */
|
|
|
|
/* Irda */
|
|
#if defined(CONFIG_OMAP_IR) || defined(CONFIG_OMAP_IR_MODULE)
|
|
omap_writel(omap_readl(FUNC_MUX_CTRL_A) | 7, FUNC_MUX_CTRL_A);
|
|
if (gpio_request(H2_IRDA_FIRSEL_GPIO_PIN, "IRDA mode") < 0)
|
|
BUG();
|
|
gpio_direction_output(H2_IRDA_FIRSEL_GPIO_PIN, 0);
|
|
h2_irda_data.transceiver_mode = h2_transceiver_mode;
|
|
#endif
|
|
|
|
platform_add_devices(h2_devices, ARRAY_SIZE(h2_devices));
|
|
omap_board_config = h2_config;
|
|
omap_board_config_size = ARRAY_SIZE(h2_config);
|
|
omap_serial_init();
|
|
omap_register_i2c_bus(1, 100, h2_i2c_board_info,
|
|
ARRAY_SIZE(h2_i2c_board_info));
|
|
h2_mmc_init();
|
|
}
|
|
|
|
static void __init h2_map_io(void)
|
|
{
|
|
omap1_map_common_io();
|
|
}
|
|
|
|
MACHINE_START(OMAP_H2, "TI-H2")
|
|
/* Maintainer: Imre Deak <imre.deak@nokia.com> */
|
|
.phys_io = 0xfff00000,
|
|
.io_pg_offst = ((0xfef00000) >> 18) & 0xfffc,
|
|
.boot_params = 0x10000100,
|
|
.map_io = h2_map_io,
|
|
.init_irq = h2_init_irq,
|
|
.init_machine = h2_init,
|
|
.timer = &omap_timer,
|
|
MACHINE_END
|