146 lines
2.6 KiB
Plaintext
146 lines
2.6 KiB
Plaintext
/*
|
|
* PHYTEC phyCORE-LPC3250 board
|
|
*
|
|
* Copyright 2012 Roland Stigge <stigge@antcom.de>
|
|
*
|
|
* The code contained herein is licensed under the GNU General Public
|
|
* License. You may obtain a copy of the GNU General Public License
|
|
* Version 2 or later at the following locations:
|
|
*
|
|
* http://www.opensource.org/licenses/gpl-license.html
|
|
* http://www.gnu.org/copyleft/gpl.html
|
|
*/
|
|
|
|
/dts-v1/;
|
|
/include/ "lpc32xx.dtsi"
|
|
|
|
/ {
|
|
model = "PHYTEC phyCORE-LPC3250 board based on NXP LPC3250";
|
|
compatible = "phytec,phy3250", "nxp,lpc3250";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
memory {
|
|
device_type = "memory";
|
|
reg = <0 0x4000000>;
|
|
};
|
|
|
|
ahb {
|
|
mac: ethernet@31060000 {
|
|
phy-mode = "rmii";
|
|
use-iram;
|
|
};
|
|
|
|
/* Here, choose exactly one from: ohci, usbd */
|
|
ohci@31020000 {
|
|
transceiver = <&isp1301>;
|
|
status = "okay";
|
|
};
|
|
|
|
/*
|
|
usbd@31020000 {
|
|
transceiver = <&isp1301>;
|
|
status = "okay";
|
|
};
|
|
*/
|
|
|
|
clcd@31040000 {
|
|
status = "okay";
|
|
};
|
|
|
|
/* 64MB Flash via SLC NAND controller */
|
|
slc: flash@20020000 {
|
|
status = "okay";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
mtd0@00000000 {
|
|
label = "phy3250-boot";
|
|
reg = <0x00000000 0x00064000>;
|
|
read-only;
|
|
};
|
|
|
|
mtd1@00064000 {
|
|
label = "phy3250-uboot";
|
|
reg = <0x00064000 0x00190000>;
|
|
read-only;
|
|
};
|
|
|
|
mtd2@001f4000 {
|
|
label = "phy3250-ubt-prms";
|
|
reg = <0x001f4000 0x00010000>;
|
|
};
|
|
|
|
mtd3@00204000 {
|
|
label = "phy3250-kernel";
|
|
reg = <0x00204000 0x00400000>;
|
|
};
|
|
|
|
mtd4@00604000 {
|
|
label = "phy3250-rootfs";
|
|
reg = <0x00604000 0x039fc000>;
|
|
};
|
|
};
|
|
|
|
apb {
|
|
i2c1: i2c@400A0000 {
|
|
clock-frequency = <100000>;
|
|
|
|
pcf8563: rtc@51 {
|
|
compatible = "nxp,pcf8563";
|
|
reg = <0x51>;
|
|
};
|
|
|
|
uda1380: uda1380@18 {
|
|
compatible = "nxp,uda1380";
|
|
reg = <0x18>;
|
|
power-gpio = <&gpio 0x59 0>;
|
|
reset-gpio = <&gpio 0x51 0>;
|
|
dac-clk = "wspll";
|
|
};
|
|
};
|
|
|
|
i2c2: i2c@400A8000 {
|
|
clock-frequency = <100000>;
|
|
};
|
|
|
|
i2cusb: i2c@31020300 {
|
|
clock-frequency = <100000>;
|
|
|
|
isp1301: usb-transceiver@2c {
|
|
compatible = "nxp,isp1301";
|
|
reg = <0x2c>;
|
|
};
|
|
};
|
|
|
|
ssp0: ssp@20084000 {
|
|
eeprom: at25@0 {
|
|
compatible = "atmel,at25";
|
|
};
|
|
};
|
|
};
|
|
|
|
fab {
|
|
tsc@40048000 {
|
|
status = "okay";
|
|
};
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led0 {
|
|
gpios = <&gpio 5 1 1>; /* GPO_P3 1, GPIO 80, active low */
|
|
linux,default-trigger = "heartbeat";
|
|
default-state = "off";
|
|
};
|
|
|
|
led1 {
|
|
gpios = <&gpio 5 14 1>; /* GPO_P3 14, GPIO 93, active low */
|
|
linux,default-trigger = "timer";
|
|
default-state = "off";
|
|
};
|
|
};
|
|
};
|