There is no need to have two snd_soc_dai_link structure for the two setup
the machine driver supports.
We can just tell core to register only the first link if the DMIC link is
not in use on the device.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Device tree support for OMAP4+ dmic cpu dai driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Device tree support for OMAP4+ McPDM cpu dai driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
In capture stream the buffer size does not need to be constrained to be
bigger then the McBSP FIFO.
In capture the FIFO content is taken out in period length burst, this
enusres that the FIFO is not going to overflow.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
With the common irq the driver only needs to use one interrupt line, and
it provides better debugging possibilites compared to the legacy TX/RX
interrupt lines.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
The frame dma_op_mode has never been used, and it is just creating
confusion for users/developers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Take the DMA packet mode into use when the McBSP is configured in element
dma_op_mode if the stream is not mono.
In this way we transfer one sample from/to McBSP FIFO upon DMA request.
This change only affects OMAP3+ versions, where the McBSP ports have FIFO.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
These are all new code, they've been in -next already so should be OK
for merge this time round. I'd been planning to send a pull request
today after they'd had a bit of exposure there to make sure breakage
didn't propagate into your tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=5L34
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Last minute updates
These are all new code, they've been in -next already so should be OK
for merge this time round. I'd been planning to send a pull request
today after they'd had a bit of exposure there to make sure breakage
didn't propagate into your tree.
The major thing here is the addition of some helpers to factor code out
of drivers, making a fair proportion of regulators much more just data
rather than code which is nice.
- Helpers in the core for regulators using regmap, providing generic
implementations of the enable and voltage selection operations which
just need data to describe them in the drivers.
- Split out voltage mapping and voltage setting, allowing many more
drivers to take advantage of the infrastructure for selectors.
- Loads and loads of cleanups from Axel Lin once again, including many
changes to take advantage of the above new framework features
- New drivers for Ricoh RC5T583, TI TPS62362, TI TPS62363, TI TPS65913,
TI TWL6035 and TI TWL6037.
Some of the registration changes to support the core refactoring caused
so many conflicts that eventually topic branches were abandoned for this
release.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=UR7s
-----END PGP SIGNATURE-----
Merge tag 'regulator-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"The major thing here is the addition of some helpers to factor code
out of drivers, making a fair proportion of regulators much more just
data rather than code which is nice.
- Helpers in the core for regulators using regmap, providing generic
implementations of the enable and voltage selection operations which
just need data to describe them in the drivers.
- Split out voltage mapping and voltage setting, allowing many more
drivers to take advantage of the infrastructure for selectors.
- Loads and loads of cleanups from Axel Lin once again, including many
changes to take advantage of the above new framework features
- New drivers for Ricoh RC5T583, TI TPS62362, TI TPS62363, TI
TPS65913, TI TWL6035 and TI TWL6037.
Some of the registration changes to support the core refactoring
caused so many conflicts that eventually topic branches were abandoned
for this release."
* tag 'regulator-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (227 commits)
regulator: tps65910: use of_node of matched regulator being register
regulator: tps65910: dt: support when "regulators" node found
regulator: tps65910: add error message in case of failure
regulator: tps62360: dt: initialize of_node param for regulator register.
regulator: tps65910: use devm_* for memory allocation
regulator: tps65910: use small letter for regulator names
mfd: tpx6586x: Depend on regulator
regulator: regulator for Palmas Kconfig
regulator: regulator driver for Palmas series chips
regulator: Enable Device Tree for the db8500-prcmu regulator driver
regulator: db8500-prcmu: Separate regulator registration from probe
regulator: ab3100: Use regulator_map_voltage_iterate()
regulator: tps65217: Convert to set_voltage_sel and map_voltage
regulator: Enable the ab8500 for Device Tree
regulator: ab8500: Split up probe() into manageable pieces
regulator: max8925: Remove check_range function and max_uV from struct rc5t583_regulator_info
regulator: max8649: Remove unused check_range() function
regulator: rc5t583: Remove max_uV from struct rc5t583_regulator_info
regulator: da9052: Convert to set_voltage_sel and map_voltage
regulator: max8952: Use devm_kzalloc
...
Set some substream struct members to make the proc interface code work
again.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Felix Homann <linuxaudio@showlabor.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The handling for some PCM states is missing for snd_pcm_drain().
At least, XRUN streams should be simply dropped to SETUP, and a few
initial invalid states should be rejected.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The module_platform_driver() conversion ended up tripping over the driver
name, leading to confusion in the macro with regards to 'driver' being
redefined. rename it to something slightly more suitable to avoid
namespace collisions.
sound/sh/sh_dac_audio.c:444:122: error: conflicting types for 'driver_init'
include/linux/device.h:773:6: note: previous declaration of 'driver_init' was here
make[3]: *** [sound/sh/sh_dac_audio.o] Error 1
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SupherH FSI2 can use special data transfer,
but it depends on CPU-FSI2 connection style.
We can use 16bit data stream mode if it was valid connection,
and it is required for 16bit data DMA transfer / SPDIF sound output.
We can use 24bit data transfer if it was invalid connection.
We can select connection type if CPU is SH7372,
and it is always valid connection if latest SuperH.
This patch adds new bus_option and fsi_bus_setup()
for supporting these feature.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
fsi_hw_startup/shutdown() needs the setup of bus width,
but it is impossible to get parameter of snd_pcm_runtime at this timing.
So, these functions are changed so that be called from fsi_dai_trigger().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds fsi_version() function for accessing version.
And there were some meaningless version check which never hit.
This patch removed it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Like the previous fixes for cache hash accesses, a protection over
accesses to the widget connection list array must be provided.
Together with this action, remove snd_hda_get_conn_list() which can be
always race, and replace it with either snd_hda_get_num_conns() or
snd_hda_get_connections() calls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Introduce codec for HDMI. At the moment, this is a dummy codec. In the
future it will parse the EDID to modify the supported parameters, such
as the number of channels and the sample rates. At the moment, it blindly
supports all the sample rates and audio channels described in the HDMI
1.4a specification.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is an spin_unlock() missing on this error path.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few last-minute regression fixes for 3.4 final kernel.
All trivial, and Cc'ed to stable kernel.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQIcBAABAgAGBQJPs5nDAAoJEGwxgFQ9KSmkKqAP/AxbPIMOhYtwJXSLIBJdDTBy
QIh7SUZTDF7m3h3pElFIUzb6NXftBOktwNBCYjYrtWH3hv6a0XwAG/zs2ysvHo4O
1iIEIT61ojckSC2OXqdCLSnZrLZmysuBUJEt8JdpHKoGnfxt8xUUSOqtIggur6s+
T34u1pqJr7gcaU0/51XXqGqR2s4qui8LkSyPVx+s3Pz4+mfh+um1SBcYz5bYpkXe
04gwCR6qrxwvqn1gGUiwFw1KtWNuD+BwWyLN+WNWLrm7NVipVLPaAaCjvnouxYwU
Z9psy3QgwgFyJ0k27lWf+NkP25/9NXuj0yaV0++dUHR4QP3+P9IJpvpyFLvkyXBe
EPjLsAdW9WQKlp/0eN/b2k8825Ip5on3UNrQhTmXc0QLC6bCyoRlznSI2nKC7rZw
eYcFUv37pka3iL9i/cNQKwhY8iRwts6vAuHdqONA3iDyCoBIYWsZZDzs+tjc3xYN
f1cI+vbDLatzpn6ut2yXIqCHJLLUROL6DnKC6l86+7DNXo7hJ9CZOSgedhvdPRc6
sayOsbWwG8RX7vLsbp4SvfpaGwI+GtfFoaECKcLW5Tem8xLuTbUcuIavAyjqxzrk
Shp7TGDmM5U1JFcXK3ZtvUcumBFjTa2rl9OB5dHMzLQV8KZAzeVUNqSHm4pma3SX
NpdEX7QxM83K0zSnppjh
=e/ZS
-----END PGP SIGNATURE-----
Merge tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A few last-minute regression fixes for 3.4 final kernel. All trivial,
and Cc'ed to stable kernel."
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: wm8994: Fix AIF2ADC power down
ALSA: hda/idt - Fix power-map for speaker-pins with some HP laptops
ASoC: cs42l73: Sync digital mixer kcontrols to allow for 0dB
* 'clk-next' of git://git.linaro.org/people/mturquette/linux:
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
ARM: Orion: SDIO: Add support for clk.
ARM: Orion: NAND: Add support for clk, if there is one.
ARM: Orion: EHCI: Add support for enabling clocks
ARM: Orion: SATA: Add per channel clk/clkdev support.
ARM: Orion: UART: Get the clock rate via clk_get_rate().
ARM: Orion: WDT: Add clk/clkdev support
ARM: Orion: Eth: Add clk/clkdev support.
ARM: Orion: SPI: Add clk/clkdev support.
ARM: Orion: Add clocks using the generic clk infrastructure.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit 4924082 "ASoC: core: Flip master for CODECs in the CPU slot of a
CODEC<->CODEC link" added code that was conditional on there being no
PCM/DMA driver for the link. However, it failed to cover the case where
the link was instantiated from device tree, and hence was specified by
DT node rather than name.
This prevents the following error on Toshiba AC100:
aplay: pcm_write:1603: write error: Input/output error
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some last minute fixes for ASoC. Small, focused changes to specific
drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=iqgt
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Last minute fixes
Some last minute fixes for ASoC. Small, focused changes to specific
drivers.
* linus/master: (805 commits)
tty: Fix LED error return
openvswitch: checking wrong variable in queue_userspace_packet()
bonding: Fix LACPDU rx_dropped commit.
Linux 3.4-rc7
ARM: EXYNOS: fix ctrlbit for exynos5_clk_pdma1
ARM: EXYNOS: use s5p-timer for UniversalC210 board
ARM / mach-shmobile: Invalidate caches when booting secondary cores
ARM / mach-shmobile: sh73a0 SMP TWD boot regression fix
ARM / mach-shmobile: r8a7779 SMP TWD boot regression fix
ARM: mach-shmobile: convert ag5evm to use the generic MMC GPIO hotplug helper
ARM: mach-shmobile: convert mackerel to use the generic MMC GPIO hotplug helper
MAINTAINERS: Add myself as the cpufreq maintainer
dm mpath: check if scsi_dh module already loaded before trying to load
dm thin: correct module description
dm thin: fix unprotected use of prepared_discards list
dm thin: reinstate missing mempool_free in cell_release_singleton
gpio/exynos: Fix compiler warnings when non-exynos machines are selected
gpio: pch9: Use proper flow type handlers
powerpc/irq: Fix another case of lazy IRQ state getting out of sync
ks8851: Update link status during link change interrupt
...
Conflicts:
drivers/media/common/tuners/xc5000.c
drivers/media/common/tuners/xc5000.h
drivers/usb/gadget/uvc_queue.c
get_min_max_with_quirks() must be called after the control id name
string is determined, but the current code changes the id name string
after calling the function.
Reported-by: Christian Melki <christian.melki@ericsson.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch just sets the codec probe_mask=0x101 value for the WinFast VP200 H
PCoIP card based on Teradici hardware matching the PCI subsystem vendor/device
IDs 3a21:040d. The user reported no codec detection issues without this
explicit codec configuration.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Maintain both streams (playback, capture) synchronized. Previous code
didn't take in account the small byte count drifts caused by the irq
position rounding.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BIOS on some HP laptops don't set the speaker-pins as fixed but expose
as jacks, and this confuses the driver as if these pins are
jack-detectable. As a result, the machine doesn't get sounds from
speakers because the driver prepares the power-map update via jack
unsol events which never come up in reality. The bug was introduced
in some time in 3.2 for enabling the power-mapping feature.
This patch fixes the problem by replacing the check of the persistent
power-map bits with a proper is_jack_detectable() call.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43240
Cc: <stable@vger.kernel.org> [v3.2+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Rename the function v4l2_dont_use_lock to v4l2_disable_ioctl_locking,
and rename v4l2_dont_use_cmd to v4l2_disable_ioctl.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
aic3x_set_headset_detection() isn't made available outside the driver or
referenced within the driver which sparse notices and complains about.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add the support for VGA-switcheroo in the HD-audio controller side.
When the graphics controller is disabled, the HD-audio driver also delays
the initialization until it's activated by VGA-switcheroo.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43155
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It's a preliminary work for the vga-switcher support.
Export the function to do pseudo-lock for the sound card to be used
in other places.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a discrete-GPU is disabled by the VGA switcheroo, the
corresponding HD-audio controller for HDMI output is also disabled.
Such a dead controller still appears in the PCI device list, but you
can't access properly any longer (even calling pci_read_config_*()
triggers Oops!) which leads the stall of the whole communication of
the driver.
This patch adds a check of graphics controller at the probe time to
see whether it's disabled by vga-switcheroo. If disabled, skip the
whole initialization of this controller.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43155
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The tea575x-tuner framework can support the VIDIOC_S_HW_FREQ_SEEK for only
some of the tea575x-based boards. Mark this ioctl as invalid if the board
doesn't support it.
This fixes an issue with S_HW_FREQ_SEEK in combination with priority handling:
since the priority check is done first it could return -EBUSY, even though
calling the S_HW_FREQ_SEEK ioctl would return -ENOTTY. It should always return
ENOTTY in such a case.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Trying to flush completed packets is pointless when the pointer
callback was called from the packet completion callback; avoid it.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
By flushing all completed but not yet reported packets before reading
the PCM hardware position, the granularity of the pointer is improved
from the interrupt interval to the packet size.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The following patch might introduce this call chain:
PCM .pointer callback
+ fw_iso_context_flush_completions
+ packet callback
+ snd_pcm_period_elapsed
+ PCM .pointer callback
Recursive calls to the pointer callback are not possible due to the PCM
group locking, so avoid this by moving the period notification into
a separate tasklet.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In preparation for irq_domain support change the code to the not switch
based on the irq number. This actually makes things simpler, if slightly
repetitive.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the devm_ versions of the regmap and memory allocation functions,
saving some error handling code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since we only need to clock AIF2 when it's actively in use start up the
FLL for it using a supply widget which supplies AIF2CLK. This both makes
the sequencing more robust and ensures we minimise power consumption.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add device tree probe for mxs-sgtl5000 machine driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add device tree probe for mxs-saif driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Same as the commit 518de86 (ASoC: tegra: register 'platform' from DAIs,
get rid of pdev), it makes mxs-pcm not a platform_driver but helper to
register "platform", so that the platform_device for mxs-pcm can be
saved completely.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It turned out that the FLOAT format on CS4206 results in simple
noises, which implies that this is no right format as is.
Since CS4206 is the only codec supporting the float, let's disable it
until we find the correct format.
Reported-and-tested-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some of the Digital mixer kcontrol max values were off by 1 not allowing a max of 0dB.
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Explained by Takashi in <s5hfwbtmz0q.wl%tiwai@suse.de>
> The reason is because get_min_max*() isn't called in the place you
> created these controls, and get_min_max() would be called only for
> integer volumes later even if uninitialized. A short cut for booleans.
Signed-off-by: Mark Hills <mark@pogo.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the PCM read/write loop, the driver calls snd_pcm_update_hw_ptr()
at each time at the beginning of the loop. Russell King reported that
this hogs CPU significantly.
The current code assumes that the pointer callback is very fast and
cheap, also not too much fine grained. It's not true in all cases.
When the pointer advances short samples while the read/write copy has
been performed, the driver updates the hw_ptr and gets avail > 0
again. Then it tries to read/write these small chunks. This repeats
until the avail really gets to zero.
For avoiding this situation, a simple workaround is to call
snd_pcm_update_hw_ptr() only once at starting the loop, assuming that
the read/write copy is performed fast enough. If the available count
becomes short, it goes to snd_pcm_wait_avail() anyway, and this
processes right.
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When pdata->reset_pin is passed with a negative value (means gpio
is invalid), then chip->reset_pin will not be assigned to a vaule,
it will use default value 0. This will cause unexpected behavior.
So, add this patch to correct.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Slightly more than expected as rc7, but all are reasonablly small fixes.
A few additions of HD-audio fixup entries, a couple of other regression
fixes including a revert, and a few other trivial oneliners.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=7Zz7
-----END PGP SIGNATURE-----
Merge tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Slightly more than expected as rc7, but all are reasonablly small
fixes. A few additions of HD-audio fixup entries, a couple of other
regression fixes including a revert, and a few other trivial
oneliners."
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: sh: fix migor.c compilation
ALSA: HDA: Lessen CPU usage when waiting for chip to respond
Revert "ALSA: hda - Set codec to D3 forcibly even if not used"
ALSA: hda/realtek - Call alc_auto_parse_customize_define() always after fixup
ALSA: hdsp - Provide ioctl_compat
ALSA: hda/realtek - Add missing CD-input pin for MSI-7350 mobo
ALSA: hda/realtek - Add a fixup for Acer Aspire 5739G
ALSA: echoaudio: Remove incorrect part of assertion
The amp and caps hashes aren't protected properly for concurrent
accesses. Protect them via a new mutex now.
But it can't be so simple as originally thought: since the update of a
hash table entry itself might trigger the power-up sequence which
again accesses the hash table, we can't cover the whole function
simply via mutex. Thus the update part has to be split from the mutex
and revalidated.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
They pollute the global namespace and cause sparse to complain.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
It can only be used with a machine driver so the idiomatic thing for
ASoC is to select this driver from the machine driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The controller is compatible with HD-audio 1.0a with some specific
restrictions.
- The BDLE entries can't be over 4k boundary
- No position-buffer and no MSI
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Makes sparse happy and avoids polluting the global namespace.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
We need to read the real register values
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
An API update which wasn't sufficiently thorough in updating the tree...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=HF38
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Build fix for SH in 3.4
An API update which wasn't sufficiently thorough in updating the tree...
We're trying to remove all usage of the ASoc level cache and I/O code and
for a device like this with a pretty sparse register map the rbtree cache
is a better idea anyway.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add driver for running I2S with the MSP-block.
Signed-off-by: Ola Lilja <ola.o.lilja@stericsson.com>
[Fixed trailing whitespace -- broonie]
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix a recent compilation breakage, caused by a change in SH clock API.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Check the power_transition up/down state instead of boolean bit, so
that the power-up sequence can cancel the pending power-down work
properly. Also, by moving cancel_delayed_work_sync() before the
actual power-up sequence, make sure that the delayed power-down is
completed.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the recent commit, the resume procedure is always performed at
the resume time. This makes the pre_resume hack for VREF mute LED on
some HP laptops superfluous. As this is the only user of pre_resume
(and there is no user of post_suspend) ops, let's kill them again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When an IRQ for some reason gets lost, we wait up to a second using
udelay, which is CPU intensive. This patch improves the situation by
waiting about 30 ms in the CPU intensive mode, then stepping down to
using msleep(2) instead. In essence, we trade some granularity in
exchange for less CPU consumption when the waiting time is a bit longer.
As a result, PulseAudio should no longer be killed by the kernel
for taking up to much RT-prio CPU time. At least not for *this* reason.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Tested-by: Arun Raghavan <arun.raghavan@collabora.co.uk>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the fixup helper functions in patch_realtek.c to hda_auto_parser.c
so that they can be used in other codec drivers like patch_conexant.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some power-saving states have been left unchanged in
snd_hda_codec_reset(), and this is a potential danger because the
function may be called in various situations including the continuous
operation after that call.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a fix for the problem in commit 785f857d1c, the pop noise
issue on some machines with ALC269. The problem was the uninitialized
state after the resume due to the delayed resume of the codec chips.
In that commit, we tried to fix by forcibly putting the codec to D3 at
suspend. But, this still also leaves the uninitialized state after
resume, and it _might_ be still problematic with some BIOS. Since the
commit turned out to regress another issues, we reverted it in the
end.
Now, in this fix, try to fix by turning on the codec immediately at
the resume path. We need to take care of the power-saving in this
case. When the device is woken up at the power-saved state, it should
go power-saving again after the resume.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The upper limit of the available minors isn't necessarily 128 + unit,
but it's rather up to 256. Fixing this allows more than 8 devices.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are left-over codes from the ancient days with the static device
number limitation of 8. Actaully OSS can support up to 16 cards.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit 785f857d1c.
The commit causes a problem with the wrong D3 state after suspend
because the call of hda_set_power_state() involves with the power-up
sequence, which changes the power_count, and this confuses the resume
sequence that checks the power_count as well.
Originally, this go-to-D3 sequence should be a simple task without the
power-up sequence. But, it'd need some proper sanity checks in the
case of power-saved state, so it's not too easy to write now in the
3.4-rc cycle.
In short, the safest option now is to revert this affecting commit.
Of course, we need to clean up and robustify the power-saving code
better for 3.5 kernel.
Reported-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The call for alc_auto_parse_customize_define() must be done after the
fixup pre-probe initialization. Otherwise SKU_IGNORE fixup won't work
properly (e.g. HP RP5800 with ALC662 codec).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When we instantiate an aux_dev we use a fake rtd as part of the process
which doesn't have a dai_link associated with it. Fix the dpcm startup
code to cope with this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
snd_hdsp uses its own ioctls to acquire config- and status information.
Expose the corresponding ioctl handler via ioctl_compat, so that 32bit applications can use it on 64bit kernels.
Signed-off-by: Andre Schramm <andre.schramm@iosono-sound.com>
Reviewed-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
None of the machines uses the gain ramp possibility for HS/HF.
This code path is mostly unused and it does not reduces the pop
noise on the output (it alters it to sound a bit different).
The preferred method to reduce pop noise is to use ABE.
Remove the gain ramp, and related features form the driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since this is a generic API which should support any userspace interface
for reporting jacks update the documentation a little to make that a bit
clearer.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allocating the SSP DMA parameters in startup, freeing it in
shutdown instead of freeing and re-allocating it in hw_params.
After doing that, the logic is clear and more safe.
Signed-off-by: guoyh <guoyh@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acer Aspire 5739G requires the same fix-up for 4930G to support the
surround / bass speakers.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43180
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This assertion seems to imply that chip->dsp_code_to_load is a pointer.
It's actually an integer handle on the actual firmware, and 0 has no
special meaning.
The assertion prevents initialisation of a Darla20 card, but would also
affect other models. It seems it was introduced in commit dd7b254d.
ALSA sound/pci/echoaudio/echoaudio.c:2061 Echoaudio driver starting...
ALSA sound/pci/echoaudio/echoaudio.c:1969 chip=ebe4e000
ALSA sound/pci/echoaudio/echoaudio.c:2007 pci=ed568000 irq=19 subdev=0010 Init hardware...
ALSA sound/pci/echoaudio/darla20_dsp.c:36 init_hw() - Darla20
------------[ cut here ]------------
WARNING: at sound/pci/echoaudio/echoaudio_dsp.c:478 init_hw+0x1d1/0x86c [snd_darla20]()
Hardware name: Dell DM051
BUG? (!chip->dsp_code_to_load || !chip->comm_page)
Signed-off-by: Mark Hills <mark@pogo.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As good as nothing exciting here; just a few trivial fixes for
various ASoC stuff.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=ZPkR
-----END PGP SIGNATURE-----
Merge tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound sound fixes from Takashi Iwai:
"As good as nothing exciting here; just a few trivial fixes for various
ASoC stuff."
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: omap-pcm: Free dma buffers in case of error.
ASoC: s3c2412-i2s: Fix dai registration
ASoC: wm8350: Don't use locally allocated codec struct
ASoC: tlv312aic23: unbreak resume
ASoC: bf5xx-ssm2602: Set DAI format
ASoC: core: check of_property_count_strings failure
ASoC: dt: sgtl5000.txt: Add description for 'reg' field
ASoC: wm_hubs: Make sure we don't disable differential line outputs
Add the PCI ID of the Asus Xonar DGX card; it's otherwise
identical with the DG.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Nothing terribly exciting here, a bunch of small and simple fixes
scattered around the place.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Z1L5
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for 3.4
Nothing terribly exciting here, a bunch of small and simple fixes
scattered around the place.
Signed-off-by: Oleg Matcovschi <oleg.matcovschi@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
This patch improves playback quality for few sample rates like 8000 and
11025 Hz.
This also fixes an issue observed during testing of pll slave mode. Due
to the issue, on some rare occasions there was no sound output for first
time playback after system boot, though all subsequent playbacks were
fine. It was mainly because of the sequence in which SRM bit was
enabled.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than invalidating the cached DCS value every time the headphone
gain changes store multiple values, indexed by gain. This allows the
optimisation we get from the cache to take effect more often.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This binding doesn't include the nvidia,model or nvidia,audio-routing
properties the other Tegra audio DT bindings have, because this binding
is targetted at a single machine, rather than for any machine using the
tlv320aic23 codec.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As s3c2412-i2s is using the s3c_i2sv2 it should call the more specialised
s3c_i2sv2_register_dai instead of simply calling snd_soc_register_dai.
Without this call the snd_soc_dai_ops structure isn't initialised correctly.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is now very standard behaviour for CODECs so shouldn't be device
specific and we shouldn't really be trying to peer into the register
cache from atomic context anyway.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In the conversion to module_init_i2c() the original open coded module
exit function was left. Remove it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for Cirrus Logic CS42L52 Low Power Stereo Codec
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Georgi Vlaev <joe@nucleusys.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The core allocates the live copies, we shouldn't try to duplicate it and
were buggy trying to do so as we were using uninitialised data for the
control data.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We should check dailess before dereferencing.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* commit f9dfbf9 "ASoC: tlv320aic23: convert to soc-cache" leads to
a bug preventing resumeof the codec as regmap expects a 9 bits data
register but 0xFFFF is passed in tlv320aic23_set_bias_level and this
values gets cached preventing any write to the TLV320AIC23_PWR
register as the final value produced by regmap is (register << 9) | value
* this patch solves the problem by only working on the 9 bits the
register contains.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
It tries to clk_get the clock. And if it failed, it assumes the clock
by default enabled.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Class W can be used for any path where only data from the DAC is routed
to the headphones. Currently we only enable it when the direct DAC to
headphone path is used but it can also be enabled for paths that go via
the output mixer providing the DAC is the only input to the output mixer.
Implement support for this, including updates to the class W status when
the output mixer configuration is changed. This also allows us to enable
the DC servo optimisations for DAC to headphone paths where the output
mixer is used.
In general the direct DAC path is still preferred as this will offer
better performance on most wm_hubs devices but these additional paths
can simplify use case management.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since the analogue portions of the checks for class W are the same over
all the devices factor out these checks into wm_hubs and while we're at
it also use wm_hubs_dac_hp_direct() to enable class W optimisations on
more paths.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The optimisations which we can do with caching the headphone DCS result in
wm_hubs have only been enabled in cases where class W is enabled. However,
there are more use cases which can benefit from the cache, especially with
WM8994 series devices with their more advanced digital routing.
Rather than keying off the class W information from the CODECs have a
check in wm_hubs for a suitable path and use that to determine if we can
deploy our headphone optimisations.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remove writable debugFS permission, use simple_open() and
fix indentation.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch fixes a bug discovered during testing of non pll slave mode.
Due to the bug chip was not getting correctly configured and as a result
there was no sound output while playback. After applying this patch,
both pll and non pll modes work fine.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
