There is little motiviation for reclaim_mode_t once RECLAIM_MODE_[A]SYNC
and lumpy reclaim have been removed. This patch gets rid of
reclaim_mode_t as well and improves the documentation about what
reclaim/compaction is and when it is triggered.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ying Han <yinghan@google.com>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch stops reclaim/compaction entering sync reclaim as this was
only intended for lumpy reclaim and an oversight. Page migration has
its own logic for stalling on writeback pages if necessary and memory
compaction is already using it.
Waiting on page writeback is bad for a number of reasons but the primary
one is that waiting on writeback to a slow device like USB can take a
considerable length of time. Page reclaim instead uses
wait_iff_congested() to throttle if too many dirty pages are being
scanned.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ying Han <yinghan@google.com>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This series removes lumpy reclaim and some stalling logic that was
unintentionally being used by memory compaction. The end result is that
stalling on dirty pages during page reclaim now depends on
wait_iff_congested().
Four kernels were compared
3.3.0 vanilla
3.4.0-rc2 vanilla
3.4.0-rc2 lumpyremove-v2 is patch one from this series
3.4.0-rc2 nosync-v2r3 is the full series
Removing lumpy reclaim saves almost 900 bytes of text whereas the full
series removes 1200 bytes.
text data bss dec hex filename
6740375 1927944 2260992 10929311 a6c49f vmlinux-3.4.0-rc2-vanilla
6739479 1927944 2260992 10928415 a6c11f vmlinux-3.4.0-rc2-lumpyremove-v2
6739159 1927944 2260992 10928095 a6bfdf vmlinux-3.4.0-rc2-nosync-v2
There are behaviour changes in the series and so tests were run with
monitoring of ftrace events. This disrupts results so the performance
results are distorted but the new behaviour should be clearer.
fs-mark running in a threaded configuration showed little of interest as
it did not push reclaim aggressively
FS-Mark Multi Threaded
3.3.0-vanilla rc2-vanilla lumpyremove-v2r3 nosync-v2r3
Files/s min 3.20 ( 0.00%) 3.20 ( 0.00%) 3.20 ( 0.00%) 3.20 ( 0.00%)
Files/s mean 3.20 ( 0.00%) 3.20 ( 0.00%) 3.20 ( 0.00%) 3.20 ( 0.00%)
Files/s stddev 0.00 ( 0.00%) 0.00 ( 0.00%) 0.00 ( 0.00%) 0.00 ( 0.00%)
Files/s max 3.20 ( 0.00%) 3.20 ( 0.00%) 3.20 ( 0.00%) 3.20 ( 0.00%)
Overhead min 508667.00 ( 0.00%) 521350.00 (-2.49%) 544292.00 (-7.00%) 547168.00 (-7.57%)
Overhead mean 551185.00 ( 0.00%) 652690.73 (-18.42%) 991208.40 (-79.83%) 570130.53 (-3.44%)
Overhead stddev 18200.69 ( 0.00%) 331958.29 (-1723.88%) 1579579.43 (-8578.68%) 9576.81 (47.38%)
Overhead max 576775.00 ( 0.00%) 1846634.00 (-220.17%) 6901055.00 (-1096.49%) 585675.00 (-1.54%)
MMTests Statistics: duration
Sys Time Running Test (seconds) 309.90 300.95 307.33 298.95
User+Sys Time Running Test (seconds) 319.32 309.67 315.69 307.51
Total Elapsed Time (seconds) 1187.85 1193.09 1191.98 1193.73
MMTests Statistics: vmstat
Page Ins 80532 82212 81420 79480
Page Outs 111434984 111456240 111437376 111582628
Swap Ins 0 0 0 0
Swap Outs 0 0 0 0
Direct pages scanned 44881 27889 27453 34843
Kswapd pages scanned 25841428 25860774 25861233 25843212
Kswapd pages reclaimed 25841393 25860741 25861199 25843179
Direct pages reclaimed 44881 27889 27453 34843
Kswapd efficiency 99% 99% 99% 99%
Kswapd velocity 21754.791 21675.460 21696.029 21649.127
Direct efficiency 100% 100% 100% 100%
Direct velocity 37.783 23.375 23.031 29.188
Percentage direct scans 0% 0% 0% 0%
ftrace showed that there was no stalling on writeback or pages submitted
for IO from reclaim context.
postmark was similar and while it was more interesting, it also did not
push reclaim heavily.
POSTMARK
3.3.0-vanilla rc2-vanilla lumpyremove-v2r3 nosync-v2r3
Transactions per second: 16.00 ( 0.00%) 20.00 (25.00%) 18.00 (12.50%) 17.00 ( 6.25%)
Data megabytes read per second: 18.80 ( 0.00%) 24.27 (29.10%) 22.26 (18.40%) 20.54 ( 9.26%)
Data megabytes written per second: 35.83 ( 0.00%) 46.25 (29.08%) 42.42 (18.39%) 39.14 ( 9.24%)
Files created alone per second: 28.00 ( 0.00%) 38.00 (35.71%) 34.00 (21.43%) 30.00 ( 7.14%)
Files create/transact per second: 8.00 ( 0.00%) 10.00 (25.00%) 9.00 (12.50%) 8.00 ( 0.00%)
Files deleted alone per second: 556.00 ( 0.00%) 1224.00 (120.14%) 3062.00 (450.72%) 6124.00 (1001.44%)
Files delete/transact per second: 8.00 ( 0.00%) 10.00 (25.00%) 9.00 (12.50%) 8.00 ( 0.00%)
MMTests Statistics: duration
Sys Time Running Test (seconds) 113.34 107.99 109.73 108.72
User+Sys Time Running Test (seconds) 145.51 139.81 143.32 143.55
Total Elapsed Time (seconds) 1159.16 899.23 980.17 1062.27
MMTests Statistics: vmstat
Page Ins 13710192 13729032 13727944 13760136
Page Outs 43071140 42987228 42733684 42931624
Swap Ins 0 0 0 0
Swap Outs 0 0 0 0
Direct pages scanned 0 0 0 0
Kswapd pages scanned 9941613 9937443 9939085 9929154
Kswapd pages reclaimed 9940926 9936751 9938397 9928465
Direct pages reclaimed 0 0 0 0
Kswapd efficiency 99% 99% 99% 99%
Kswapd velocity 8576.567 11051.058 10140.164 9347.109
Direct efficiency 100% 100% 100% 100%
Direct velocity 0.000 0.000 0.000 0.000
It looks like here that the full series regresses performance but as
ftrace showed no usage of wait_iff_congested() or sync reclaim I am
assuming it's a disruption due to monitoring. Other data such as memory
usage, page IO, swap IO all looked similar.
Running a benchmark with a plain DD showed nothing very interesting.
The full series stalled in wait_iff_congested() slightly less but stall
times on vanilla kernels were marginal.
Running a benchmark that hammered on file-backed mappings showed stalls
due to congestion but not in sync writebacks
MICRO
3.3.0-vanilla rc2-vanilla lumpyremove-v2r3 nosync-v2r3
MMTests Statistics: duration
Sys Time Running Test (seconds) 308.13 294.50 298.75 299.53
User+Sys Time Running Test (seconds) 330.45 316.28 318.93 320.79
Total Elapsed Time (seconds) 1814.90 1833.88 1821.14 1832.91
MMTests Statistics: vmstat
Page Ins 108712 120708 97224 110344
Page Outs 155514576 156017404 155813676 156193256
Swap Ins 0 0 0 0
Swap Outs 0 0 0 0
Direct pages scanned 2599253 1550480 2512822 2414760
Kswapd pages scanned 69742364 71150694 68839041 69692533
Kswapd pages reclaimed 34824488 34773341 34796602 34799396
Direct pages reclaimed 53693 94750 61792 75205
Kswapd efficiency 49% 48% 50% 49%
Kswapd velocity 38427.662 38797.901 37799.972 38022.889
Direct efficiency 2% 6% 2% 3%
Direct velocity 1432.174 845.464 1379.807 1317.446
Percentage direct scans 3% 2% 3% 3%
Page writes by reclaim 0 0 0 0
Page writes file 0 0 0 0
Page writes anon 0 0 0 0
Page reclaim immediate 0 0 0 1218
Page rescued immediate 0 0 0 0
Slabs scanned 15360 16384 13312 16384
Direct inode steals 0 0 0 0
Kswapd inode steals 4340 4327 1630 4323
FTrace Reclaim Statistics: congestion_wait
Direct number congest waited 0 0 0 0
Direct time congest waited 0ms 0ms 0ms 0ms
Direct full congest waited 0 0 0 0
Direct number conditional waited 900 870 754 789
Direct time conditional waited 0ms 0ms 0ms 20ms
Direct full conditional waited 0 0 0 0
KSwapd number congest waited 2106 2308 2116 1915
KSwapd time congest waited 139924ms 157832ms 125652ms 132516ms
KSwapd full congest waited 1346 1530 1202 1278
KSwapd number conditional waited 12922 16320 10943 14670
KSwapd time conditional waited 0ms 0ms 0ms 0ms
KSwapd full conditional waited 0 0 0 0
Reclaim statistics are not radically changed. The stall times in kswapd
are massive but it is clear that it is due to calls to congestion_wait()
and that is almost certainly the call in balance_pgdat(). Otherwise
stalls due to dirty pages are non-existant.
I ran a benchmark that stressed high-order allocation. This is very
artifical load but was used in the past to evaluate lumpy reclaim and
compaction. Generally I look at allocation success rates and latency
figures.
STRESS-HIGHALLOC
3.3.0-vanilla rc2-vanilla lumpyremove-v2r3 nosync-v2r3
Pass 1 81.00 ( 0.00%) 28.00 (-53.00%) 24.00 (-57.00%) 28.00 (-53.00%)
Pass 2 82.00 ( 0.00%) 39.00 (-43.00%) 38.00 (-44.00%) 43.00 (-39.00%)
while Rested 88.00 ( 0.00%) 87.00 (-1.00%) 88.00 ( 0.00%) 88.00 ( 0.00%)
MMTests Statistics: duration
Sys Time Running Test (seconds) 740.93 681.42 685.14 684.87
User+Sys Time Running Test (seconds) 2922.65 3269.52 3281.35 3279.44
Total Elapsed Time (seconds) 1161.73 1152.49 1159.55 1161.44
MMTests Statistics: vmstat
Page Ins 4486020 2807256 2855944 2876244
Page Outs 7261600 7973688 7975320 7986120
Swap Ins 31694 0 0 0
Swap Outs 98179 0 0 0
Direct pages scanned 53494 57731 34406 113015
Kswapd pages scanned 6271173 1287481 1278174 1219095
Kswapd pages reclaimed 2029240 1281025 1260708 1201583
Direct pages reclaimed 1468 14564 16649 92456
Kswapd efficiency 32% 99% 98% 98%
Kswapd velocity 5398.133 1117.130 1102.302 1049.641
Direct efficiency 2% 25% 48% 81%
Direct velocity 46.047 50.092 29.672 97.306
Percentage direct scans 0% 4% 2% 8%
Page writes by reclaim 1616049 0 0 0
Page writes file 1517870 0 0 0
Page writes anon 98179 0 0 0
Page reclaim immediate 103778 27339 9796 17831
Page rescued immediate 0 0 0 0
Slabs scanned 1096704 986112 980992 998400
Direct inode steals 223 215040 216736 247881
Kswapd inode steals 175331 61548 68444 63066
Kswapd skipped wait 21991 0 1 0
THP fault alloc 1 135 125 134
THP collapse alloc 393 311 228 236
THP splits 25 13 7 8
THP fault fallback 0 0 0 0
THP collapse fail 3 5 7 7
Compaction stalls 865 1270 1422 1518
Compaction success 370 401 353 383
Compaction failures 495 869 1069 1135
Compaction pages moved 870155 3828868 4036106 4423626
Compaction move failure 26429 23865 29742 27514
Success rates are completely hosed for 3.4-rc2 which is almost certainly
due to commit fe2c2a1066 ("vmscan: reclaim at order 0 when compaction
is enabled"). I expected this would happen for kswapd and impair
allocation success rates (https://lkml.org/lkml/2012/1/25/166) but I did
not anticipate this much a difference: 80% less scanning, 37% less
reclaim by kswapd
In comparison, reclaim/compaction is not aggressive and gives up easily
which is the intended behaviour. hugetlbfs uses __GFP_REPEAT and would
be much more aggressive about reclaim/compaction than THP allocations
are. The stress test above is allocating like neither THP or hugetlbfs
but is much closer to THP.
Mainline is now impaired in terms of high order allocation under heavy
load although I do not know to what degree as I did not test with
__GFP_REPEAT. Keep this in mind for bugs related to hugepage pool
resizing, THP allocation and high order atomic allocation failures from
network devices.
In terms of congestion throttling, I see the following for this test
FTrace Reclaim Statistics: congestion_wait
Direct number congest waited 3 0 0 0
Direct time congest waited 0ms 0ms 0ms 0ms
Direct full congest waited 0 0 0 0
Direct number conditional waited 957 512 1081 1075
Direct time conditional waited 0ms 0ms 0ms 0ms
Direct full conditional waited 0 0 0 0
KSwapd number congest waited 36 4 3 5
KSwapd time congest waited 3148ms 400ms 300ms 500ms
KSwapd full congest waited 30 4 3 5
KSwapd number conditional waited 88514 197 332 542
KSwapd time conditional waited 4980ms 0ms 0ms 0ms
KSwapd full conditional waited 49 0 0 0
The "conditional waited" times are the most interesting as this is
directly impacted by the number of dirty pages encountered during scan.
As lumpy reclaim is no longer scanning contiguous ranges, it is finding
fewer dirty pages. This brings wait times from about 5 seconds to 0.
kswapd itself is still calling congestion_wait() so it'll still stall but
it's a lot less.
In terms of the type of IO we were doing, I see this
FTrace Reclaim Statistics: mm_vmscan_writepage
Direct writes anon sync 0 0 0 0
Direct writes anon async 0 0 0 0
Direct writes file sync 0 0 0 0
Direct writes file async 0 0 0 0
Direct writes mixed sync 0 0 0 0
Direct writes mixed async 0 0 0 0
KSwapd writes anon sync 0 0 0 0
KSwapd writes anon async 91682 0 0 0
KSwapd writes file sync 0 0 0 0
KSwapd writes file async 822629 0 0 0
KSwapd writes mixed sync 0 0 0 0
KSwapd writes mixed async 0 0 0 0
In 3.2, kswapd was doing a bunch of async writes of pages but
reclaim/compaction was never reaching a point where it was doing sync
IO. This does not guarantee that reclaim/compaction was not calling
wait_on_page_writeback() but I would consider it unlikely. It indicates
that merging patches 2 and 3 to stop reclaim/compaction calling
wait_on_page_writeback() should be safe.
This patch:
Lumpy reclaim had a purpose but in the mind of some, it was to kick the
system so hard it trashed. For others the purpose was to complicate
vmscan.c. Over time it was giving softer shoes and a nicer attitude but
memory compaction needs to step up and replace it so this patch sends
lumpy reclaim to the farm.
The tracepoint format changes for isolating LRU pages with this patch
applied. Furthermore reclaim/compaction can no longer queue dirty pages
in pageout() if the underlying BDI is congested. Lumpy reclaim used
this logic and reclaim/compaction was using it in error.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ying Han <yinghan@google.com>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The swap token code no longer fits in with the current VM model. It
does not play well with cgroups or the better NUMA placement code in
development, since we have only one swap token globally.
It also has the potential to mess with scalability of the system, by
increasing the number of non-reclaimable pages on the active and
inactive anon LRU lists.
Last but not least, the swap token code has been broken for a year
without complaints, as reported by Konstantin Khlebnikov. This suggests
we no longer have much use for it.
The days of sub-1G memory systems with heavy use of swap are over. If
we ever need thrashing reducing code in the future, we will have to
implement something that does scale.
Signed-off-by: Rik van Riel <riel@redhat.com>
Cc: Konstantin Khlebnikov <khlebnikov@openvz.org>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Hugh Dickins <hughd@google.com>
Acked-by: Bob Picco <bpicco@meloft.net>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The transparent hugepages feature is careful to not invoke the oom
killer when a hugepage cannot be allocated.
pte_alloc_one() failing in __do_huge_pmd_anonymous_page(), however,
currently results in VM_FAULT_OOM which invokes the pagefault oom killer
to kill a memory-hogging task.
This is unnecessary since it's possible to drop the reference to the
hugepage and fallback to allocating a small page.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The "ret" variable is unnecessary in __do_huge_pmd_anonymous_page(), so
remove it.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The arguments f & t and fields from & to of struct file_region are
defined as long. So use long instead of int to type the temp vars.
Signed-off-by: Wang Sheng-Hui <shhuiw@gmail.com>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have enum definition in mempolicy.h: MPOL_REBIND_ONCE. It should
replace the magic number 0 for step comparison in function
mpol_rebind_policy.
Signed-off-by: Wang Sheng-Hui <shhuiw@gmail.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These things tend to get out of sync with time so let the compiler
automatically enter the current function name using __func__.
No functional change.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Acked-by: Andi Kleen <andi@firstfloor.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPw2J/AAoJECvKgwp+S8Ja5jkP/3uMxkhf8XQpXCI3O1QVfaQr
uZFfM8sINqIPDVm1dtFjFj7f8Bw9mhE2KAnnJ1rKT8tQwqq9yAse1QPlhCG1ZqoP
+AnMDDXHtx7WmQZXhBvS9b+unpZ7Jr6r6pO5XrmTL2kRL3YJPUhZ2+xbTT5belTB
KoAu4WqORZRxfXoC76S7U8K+D4NcAGhAOxCClsIjmY+oocCiCag4FZOyzYIFViqc
ghUN/+rLQ3fqGGv2yO7Ylx1gUM7sxIwkZQ/h962jFAtxz9czImr2NmRoMliOaOkS
tvcnIf+E3u0n/zIjzFvzhxKgHJPP8PkcPMk60d3jKmFngBkqFTzNUeVTP8md7HrV
4DlXisWr+z7YVyWUCFaNcJLmjiWSwQ8DV/clRLobeBf9EJKan5F1PjFgl6PLJM5F
Qr1+LHMNaetdulBwMRTyveZTzYqw9RmDnD9dWMo4mX/kTpvtC4jTPVV7hkRD+Qlv
5vTRR+VXL3Q50yClLf0AQMSKTnH2gBuepM/b+7cShLGfsMln8DtUjmbigv+niL63
BibcCIbIlP2uWGnl37VhsC34AT+RKt3lggrBOpn/7XJMq/wKR7IRP/7V9TfYgaUN
NBa+wtnLDa1pZEn/X7izdcQP62PzDtmB+ObvYT0Yb40A4+2ud3qF/lB53c1A1ewF
/9c4zxxekjHZnn2oooEa
=oLXf
-----END PGP SIGNATURE-----
Merge tag 'writeback' of git://git.kernel.org/pub/scm/linux/kernel/git/wfg/linux
Pull writeback tree from Wu Fengguang:
"Mainly from Jan Kara to avoid iput() in the flusher threads."
* tag 'writeback' of git://git.kernel.org/pub/scm/linux/kernel/git/wfg/linux:
writeback: Avoid iput() from flusher thread
vfs: Rename end_writeback() to clear_inode()
vfs: Move waiting for inode writeback from end_writeback() to evict_inode()
writeback: Refactor writeback_single_inode()
writeback: Remove wb->list_lock from writeback_single_inode()
writeback: Separate inode requeueing after writeback
writeback: Move I_DIRTY_PAGES handling
writeback: Move requeueing when I_SYNC set to writeback_sb_inodes()
writeback: Move clearing of I_SYNC into inode_sync_complete()
writeback: initialize global_dirty_limit
fs: remove 8 bytes of padding from struct writeback_control on 64 bit builds
mm: page-writeback.c: local functions should not be exposed globally
Pull tile updates from Chris Metcalf:
"These changes cover a range of new arch/tile features and
optimizations. They've been through LKML review and on linux-next for
a month or so. There's also one bug-fix that just missed 3.4, which
I've marked for stable."
Fixed up trivial conflict in arch/tile/Kconfig (new added tile Kconfig
entries clashing with the generic timer/clockevents changes).
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: default to tilegx_defconfig for ARCH=tile
tile: fix bug where fls(0) was not returning 0
arch/tile: mark TILEGX as not EXPERIMENTAL
tile/mm/fault.c: Port OOM changes to handle_page_fault
arch/tile: add descriptive text if the kernel reports a bad trap
arch/tile: allow querying cpu module information from the hypervisor
arch/tile: fix hardwall for tilegx and generalize for idn and ipi
arch/tile: support multiple huge page sizes dynamically
mm: add new arch_make_huge_pte() method for tile support
arch/tile: support kexec() for tilegx
arch/tile: support <asm/cachectl.h> header for cacheflush() syscall
arch/tile: Allow tilegx to build with either 16K or 64K page size
arch/tile: optimize get_user/put_user and friends
arch/tile: support building big-endian kernel
arch/tile: allow building Linux with transparent huge pages enabled
arch/tile: use interrupt critical sections less
The tile support for multiple-size huge pages requires tagging
the hugetlb PTE with a "super" bit for PTEs that are multiples of
the basic size of a pagetable span. To set that bit properly
we need to tweak the PTe in make_huge_pte() based on the vma.
This change provides the API for a subsequent tile-specific
change to use.
Reviewed-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
The change adds some infrastructure for managing tile pmd's more generally,
using pte_pmd() and pmd_pte() methods to translate pmd values to and
from ptes, since on TILEPro a pmd is really just a nested structure
holding a pgd (aka pte). Several existing pmd methods are moved into
this framework, and a whole raft of additional pmd accessors are defined
that are used by the transparent hugepage framework.
The tile PTE now has a "client2" bit. The bit is used to indicate a
transparent huge page is in the process of being split into subpages.
This change also fixes a generic bug where the return value of the
generic pmdp_splitting_flush() was incorrect.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Pull CMA and ARM DMA-mapping updates from Marek Szyprowski:
"These patches contain two major updates for DMA mapping subsystem
(mainly for ARM architecture). First one is Contiguous Memory
Allocator (CMA) which makes it possible for device drivers to allocate
big contiguous chunks of memory after the system has booted.
The main difference from the similar frameworks is the fact that CMA
allows to transparently reuse the memory region reserved for the big
chunk allocation as a system memory, so no memory is wasted when no
big chunk is allocated. Once the alloc request is issued, the
framework migrates system pages to create space for the required big
chunk of physically contiguous memory.
For more information one can refer to nice LWN articles:
- 'A reworked contiguous memory allocator':
http://lwn.net/Articles/447405/
- 'CMA and ARM':
http://lwn.net/Articles/450286/
- 'A deep dive into CMA':
http://lwn.net/Articles/486301/
- and the following thread with the patches and links to all previous
versions:
https://lkml.org/lkml/2012/4/3/204
The main client for this new framework is ARM DMA-mapping subsystem.
The second part provides a complete redesign in ARM DMA-mapping
subsystem. The core implementation has been changed to use common
struct dma_map_ops based infrastructure with the recent updates for
new dma attributes merged in v3.4-rc2. This allows to use more than
one implementation of dma-mapping calls and change/select them on the
struct device basis. The first client of this new infractructure is
dmabounce implementation which has been completely cut out of the
core, common code.
The last patch of this redesign update introduces a new, experimental
implementation of dma-mapping calls on top of generic IOMMU framework.
This lets ARM sub-platform to transparently use IOMMU for DMA-mapping
calls if one provides required IOMMU hardware.
For more information please refer to the following thread:
http://www.spinics.net/lists/arm-kernel/msg175729.html
The last patch merges changes from both updates and provides a
resolution for the conflicts which cannot be avoided when patches have
been applied on the same files (mainly arch/arm/mm/dma-mapping.c)."
Acked by Andrew Morton <akpm@linux-foundation.org>:
"Yup, this one please. It's had much work, plenty of review and I
think even Russell is happy with it."
* 'for-linus' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping: (28 commits)
ARM: dma-mapping: use PMD size for section unmap
cma: fix migration mode
ARM: integrate CMA with DMA-mapping subsystem
X86: integrate CMA with DMA-mapping subsystem
drivers: add Contiguous Memory Allocator
mm: trigger page reclaim in alloc_contig_range() to stabilise watermarks
mm: extract reclaim code from __alloc_pages_direct_reclaim()
mm: Serialize access to min_free_kbytes
mm: page_isolation: MIGRATE_CMA isolation functions added
mm: mmzone: MIGRATE_CMA migration type added
mm: page_alloc: change fallbacks array handling
mm: page_alloc: introduce alloc_contig_range()
mm: compaction: export some of the functions
mm: compaction: introduce isolate_freepages_range()
mm: compaction: introduce map_pages()
mm: compaction: introduce isolate_migratepages_range()
mm: page_alloc: remove trailing whitespace
ARM: dma-mapping: add support for IOMMU mapper
ARM: dma-mapping: use alloc, mmap, free from dma_ops
ARM: dma-mapping: remove redundant code and do the cleanup
...
Conflicts:
arch/x86/include/asm/dma-mapping.h
Pull more networking updates from David Miller:
"Ok, everything from here on out will be bug fixes."
1) One final sync of wireless and bluetooth stuff from John Linville.
These changes have all been in his tree for more than a week, and
therefore have had the necessary -next exposure. John was just away
on a trip and didn't have a change to send the pull request until a
day or two ago.
2) Put back some defines in user exposed header file areas that were
removed during the tokenring purge. From Stephen Hemminger and Paul
Gortmaker.
3) A bug fix for UDP hash table allocation got lost in the pile due to
one of those "you got it.. no I've got it.." situations. :-)
From Tim Bird.
4) SKB coalescing in TCP needs to have stricter checks, otherwise we'll
try to coalesce overlapping frags and crash. Fix from Eric Dumazet.
5) RCU routing table lookups can race with free_fib_info(), causing
crashes when we deref the device pointers in the route. Fix by
releasing the net device in the RCU callback. From Yanmin Zhang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (293 commits)
tcp: take care of overlaps in tcp_try_coalesce()
ipv4: fix the rcu race between free_fib_info and ip_route_output_slow
mm: add a low limit to alloc_large_system_hash
ipx: restore token ring define to include/linux/ipx.h
if: restore token ring ARP type to header
xen: do not disable netfront in dom0
phy/micrel: Fix ID of KSZ9021
mISDN: Add X-Tensions USB ISDN TA XC-525
gianfar:don't add FCB length to hard_header_len
Bluetooth: Report proper error number in disconnection
Bluetooth: Create flags for bt_sk()
Bluetooth: report the right security level in getsockopt
Bluetooth: Lock the L2CAP channel when sending
Bluetooth: Restore locking semantics when looking up L2CAP channels
Bluetooth: Fix a redundant and problematic incoming MTU check
Bluetooth: Add support for Foxconn/Hon Hai AR5BBU22 0489:E03C
Bluetooth: Fix EIR data generation for mgmt_device_found
Bluetooth: Fix Inquiry with RSSI event mask
Bluetooth: improve readability of l2cap_seq_list code
Bluetooth: Fix skb length calculation
...
Pull user-space probe instrumentation from Ingo Molnar:
"The uprobes code originates from SystemTap and has been used for years
in Fedora and RHEL kernels. This version is much rewritten, reviews
from PeterZ, Oleg and myself shaped the end result.
This tree includes uprobes support in 'perf probe' - but SystemTap
(and other tools) can take advantage of user probe points as well.
Sample usage of uprobes via perf, for example to profile malloc()
calls without modifying user-space binaries.
First boot a new kernel with CONFIG_UPROBE_EVENT=y enabled.
If you don't know which function you want to probe you can pick one
from 'perf top' or can get a list all functions that can be probed
within libc (binaries can be specified as well):
$ perf probe -F -x /lib/libc.so.6
To probe libc's malloc():
$ perf probe -x /lib64/libc.so.6 malloc
Added new event:
probe_libc:malloc (on 0x7eac0)
You can now use it in all perf tools, such as:
perf record -e probe_libc:malloc -aR sleep 1
Make use of it to create a call graph (as the flat profile is going to
look very boring):
$ perf record -e probe_libc:malloc -gR make
[ perf record: Woken up 173 times to write data ]
[ perf record: Captured and wrote 44.190 MB perf.data (~1930712
$ perf report | less
32.03% git libc-2.15.so [.] malloc
|
--- malloc
29.49% cc1 libc-2.15.so [.] malloc
|
--- malloc
|
|--0.95%-- 0x208eb1000000000
|
|--0.63%-- htab_traverse_noresize
11.04% as libc-2.15.so [.] malloc
|
--- malloc
|
7.15% ld libc-2.15.so [.] malloc
|
--- malloc
|
5.07% sh libc-2.15.so [.] malloc
|
--- malloc
|
4.99% python-config libc-2.15.so [.] malloc
|
--- malloc
|
4.54% make libc-2.15.so [.] malloc
|
--- malloc
|
|--7.34%-- glob
| |
| |--93.18%-- 0x41588f
| |
| --6.82%-- glob
| 0x41588f
...
Or:
$ perf report -g flat | less
# Overhead Command Shared Object Symbol
# ........ ............. ............. ..........
#
32.03% git libc-2.15.so [.] malloc
27.19%
malloc
29.49% cc1 libc-2.15.so [.] malloc
24.77%
malloc
11.04% as libc-2.15.so [.] malloc
11.02%
malloc
7.15% ld libc-2.15.so [.] malloc
6.57%
malloc
...
The core uprobes design is fairly straightforward: uprobes probe
points register themselves at (inode:offset) addresses of
libraries/binaries, after which all existing (or new) vmas that map
that address will have a software breakpoint injected at that address.
vmas are COW-ed to preserve original content. The probe points are
kept in an rbtree.
If user-space executes the probed inode:offset instruction address
then an event is generated which can be recovered from the regular
perf event channels and mmap-ed ring-buffer.
Multiple probes at the same address are supported, they create a
dynamic callback list of event consumers.
The basic model is further complicated by the XOL speedup: the
original instruction that is probed is copied (in an architecture
specific fashion) and executed out of line when the probe triggers.
The XOL area is a single vma per process, with a fixed number of
entries (which limits probe execution parallelism).
The API: uprobes are installed/removed via
/sys/kernel/debug/tracing/uprobe_events, the API is integrated to
align with the kprobes interface as much as possible, but is separate
to it.
Injecting a probe point is privileged operation, which can be relaxed
by setting perf_paranoid to -1.
You can use multiple probes as well and mix them with kprobes and
regular PMU events or tracepoints, when instrumenting a task."
Fix up trivial conflicts in mm/memory.c due to previous cleanup of
unmap_single_vma().
* 'perf-uprobes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
perf probe: Detect probe target when m/x options are absent
perf probe: Provide perf interface for uprobes
tracing: Fix kconfig warning due to a typo
tracing: Provide trace events interface for uprobes
tracing: Extract out common code for kprobes/uprobes trace events
tracing: Modify is_delete, is_return from int to bool
uprobes/core: Decrement uprobe count before the pages are unmapped
uprobes/core: Make background page replacement logic account for rss_stat counters
uprobes/core: Optimize probe hits with the help of a counter
uprobes/core: Allocate XOL slots for uprobes use
uprobes/core: Handle breakpoint and singlestep exceptions
uprobes/core: Rename bkpt to swbp
uprobes/core: Make order of function parameters consistent across functions
uprobes/core: Make macro names consistent
uprobes: Update copyright notices
uprobes/core: Move insn to arch specific structure
uprobes/core: Remove uprobe_opcode_sz
uprobes/core: Make instruction tables volatile
uprobes: Move to kernel/events/
uprobes/core: Clean up, refactor and improve the code
...
UDP stack needs a minimum hash size value for proper operation and also
uses alloc_large_system_hash() for proper NUMA distribution of its hash
tables and automatic sizing depending on available system memory.
On some low memory situations, udp_table_init() must ignore the
alloc_large_system_hash() result and reallocs a bigger memory area.
As we cannot easily free old hash table, we leak it and kmemleak can
issue a warning.
This patch adds a low limit parameter to alloc_large_system_hash() to
solve this problem.
We then specify UDP_HTABLE_SIZE_MIN for UDP/UDPLite hash table
allocation.
Reported-by: Mark Asselstine <mark.asselstine@windriver.com>
Reported-by: Tim Bird <tim.bird@am.sony.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Jones' system call fuzz testing tool "trinity" triggered the
following bug error with slab debugging enabled
=============================================================================
BUG numa_policy (Not tainted): Poison overwritten
-----------------------------------------------------------------------------
INFO: 0xffff880146498250-0xffff880146498250. First byte 0x6a instead of 0x6b
INFO: Allocated in mpol_new+0xa3/0x140 age=46310 cpu=6 pid=32154
__slab_alloc+0x3d3/0x445
kmem_cache_alloc+0x29d/0x2b0
mpol_new+0xa3/0x140
sys_mbind+0x142/0x620
system_call_fastpath+0x16/0x1b
INFO: Freed in __mpol_put+0x27/0x30 age=46268 cpu=6 pid=32154
__slab_free+0x2e/0x1de
kmem_cache_free+0x25a/0x260
__mpol_put+0x27/0x30
remove_vma+0x68/0x90
exit_mmap+0x118/0x140
mmput+0x73/0x110
exit_mm+0x108/0x130
do_exit+0x162/0xb90
do_group_exit+0x4f/0xc0
sys_exit_group+0x17/0x20
system_call_fastpath+0x16/0x1b
INFO: Slab 0xffffea0005192600 objects=27 used=27 fp=0x (null) flags=0x20000000004080
INFO: Object 0xffff880146498250 @offset=592 fp=0xffff88014649b9d0
This implied a reference counting bug and the problem happened during
mbind().
mbind() applies a new memory policy to a range and uses mbind_range() to
merge existing VMAs or split them as necessary. In the event of splits,
mpol_dup() will allocate a new struct mempolicy and maintain existing
reference counts whose rules are documented in
Documentation/vm/numa_memory_policy.txt .
The problem occurs with shared memory policies. The vm_op->set_policy
increments the reference count if necessary and split_vma() and
vma_merge() have already handled the existing reference counts.
However, policy_vma() screws it up by replacing an existing
vma->vm_policy with one that potentially has the wrong reference count
leading to a premature free. This patch removes the damage caused by
policy_vma().
With this patch applied Dave's trinity tool runs an mbind test for 5
minutes without error. /proc/slabinfo reported that there are no
numa_policy or shared_policy_node objects allocated after the test
completed and the shared memory region was deleted.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Cc: Dave Jones <davej@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Stephen Wilson <wilsons@start.ca>
Cc: Christoph Lameter <cl@linux.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull user namespace enhancements from Eric Biederman:
"This is a course correction for the user namespace, so that we can
reach an inexpensive, maintainable, and reasonably complete
implementation.
Highlights:
- Config guards make it impossible to enable the user namespace and
code that has not been converted to be user namespace safe.
- Use of the new kuid_t type ensures the if you somehow get past the
config guards the kernel will encounter type errors if you enable
user namespaces and attempt to compile in code whose permission
checks have not been updated to be user namespace safe.
- All uids from child user namespaces are mapped into the initial
user namespace before they are processed. Removing the need to add
an additional check to see if the user namespace of the compared
uids remains the same.
- With the user namespaces compiled out the performance is as good or
better than it is today.
- For most operations absolutely nothing changes performance or
operationally with the user namespace enabled.
- The worst case performance I could come up with was timing 1
billion cache cold stat operations with the user namespace code
enabled. This went from 156s to 164s on my laptop (or 156ns to
164ns per stat operation).
- (uid_t)-1 and (gid_t)-1 are reserved as an internal error value.
Most uid/gid setting system calls treat these value specially
anyway so attempting to use -1 as a uid would likely cause
entertaining failures in userspace.
- If setuid is called with a uid that can not be mapped setuid fails.
I have looked at sendmail, login, ssh and every other program I
could think of that would call setuid and they all check for and
handle the case where setuid fails.
- If stat or a similar system call is called from a context in which
we can not map a uid we lie and return overflowuid. The LFS
experience suggests not lying and returning an error code might be
better, but the historical precedent with uids is different and I
can not think of anything that would break by lying about a uid we
can't map.
- Capabilities are localized to the current user namespace making it
safe to give the initial user in a user namespace all capabilities.
My git tree covers all of the modifications needed to convert the core
kernel and enough changes to make a system bootable to runlevel 1."
Fix up trivial conflicts due to nearby independent changes in fs/stat.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (46 commits)
userns: Silence silly gcc warning.
cred: use correct cred accessor with regards to rcu read lock
userns: Convert the move_pages, and migrate_pages permission checks to use uid_eq
userns: Convert cgroup permission checks to use uid_eq
userns: Convert tmpfs to use kuid and kgid where appropriate
userns: Convert sysfs to use kgid/kuid where appropriate
userns: Convert sysctl permission checks to use kuid and kgids.
userns: Convert proc to use kuid/kgid where appropriate
userns: Convert ext4 to user kuid/kgid where appropriate
userns: Convert ext3 to use kuid/kgid where appropriate
userns: Convert ext2 to use kuid/kgid where appropriate.
userns: Convert devpts to use kuid/kgid where appropriate
userns: Convert binary formats to use kuid/kgid where appropriate
userns: Add negative depends on entries to avoid building code that is userns unsafe
userns: signal remove unnecessary map_cred_ns
userns: Teach inode_capable to understand inodes whose uids map to other namespaces.
userns: Fail exec for suid and sgid binaries with ids outside our user namespace.
userns: Convert stat to return values mapped from kuids and kgids
userns: Convert user specfied uids and gids in chown into kuids and kgid
userns: Use uid_eq gid_eq helpers when comparing kuids and kgids in the vfs
...
Pull cgroup updates from Tejun Heo:
"cgroup file type addition / removal is updated so that file types are
added and removed instead of individual files so that dynamic file
type addition / removal can be implemented by cgroup and used by
controllers. blkio controller changes which will come through block
tree are dependent on this. Other changes include res_counter cleanup
and disallowing kthread / PF_THREAD_BOUND threads to be attached to
non-root cgroups.
There's a reported bug with the file type addition / removal handling
which can lead to oops on cgroup umount. The issue is being looked
into. It shouldn't cause problems for most setups and isn't a
security concern."
Fix up trivial conflict in Documentation/feature-removal-schedule.txt
* 'for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: (21 commits)
res_counter: Account max_usage when calling res_counter_charge_nofail()
res_counter: Merge res_counter_charge and res_counter_charge_nofail
cgroups: disallow attaching kthreadd or PF_THREAD_BOUND threads
cgroup: remove cgroup_subsys->populate()
cgroup: get rid of populate for memcg
cgroup: pass struct mem_cgroup instead of struct cgroup to socket memcg
cgroup: make css->refcnt clearing on cgroup removal optional
cgroup: use negative bias on css->refcnt to block css_tryget()
cgroup: implement cgroup_rm_cftypes()
cgroup: introduce struct cfent
cgroup: relocate __d_cgrp() and __d_cft()
cgroup: remove cgroup_add_file[s]()
cgroup: convert memcg controller to the new cftype interface
memcg: always create memsw files if CONFIG_CGROUP_MEM_RES_CTLR_SWAP
cgroup: convert all non-memcg controllers to the new cftype interface
cgroup: relocate cftype and cgroup_subsys definitions in controllers
cgroup: merge cft_release_agent cftype array into the base files array
cgroup: implement cgroup_add_cftypes() and friends
cgroup: build list of all cgroups under a given cgroupfs_root
cgroup: move cgroup_clear_directory() call out of cgroup_populate_dir()
...
Here's the driver core, and other driver subsystems, pull request for
the 3.5-rc1 merge window.
Outside of a few minor driver core changes, we ended up with the
following different subsystem and core changes as well, due to
interdependancies on the driver core:
- hyperv driver updates
- drivers/memory being created and some drivers moved into it
- extcon driver subsystem created out of the old Android staging switch
driver code
- dynamic debug updates
- printk rework, and /dev/kmsg changes
All of this has been tested in the linux-next releases for a few weeks
with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+7q28ACgkQMUfUDdst+ykXmwCfcPASzC+/bDkuqdWsqzxlWZ7+
VOQAnAriySv397St36J6Hz5bMQZwB1Yq
=SQc+
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg Kroah-Hartman:
"Here's the driver core, and other driver subsystems, pull request for
the 3.5-rc1 merge window.
Outside of a few minor driver core changes, we ended up with the
following different subsystem and core changes as well, due to
interdependancies on the driver core:
- hyperv driver updates
- drivers/memory being created and some drivers moved into it
- extcon driver subsystem created out of the old Android staging
switch driver code
- dynamic debug updates
- printk rework, and /dev/kmsg changes
All of this has been tested in the linux-next releases for a few weeks
with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fix up conflicts in drivers/extcon/extcon-max8997.c where git noticed
that a patch to the deleted drivers/misc/max8997-muic.c driver needs to
be applied to this one.
* tag 'driver-core-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (90 commits)
uio_pdrv_genirq: get irq through platform resource if not set otherwise
memory: tegra{20,30}-mc: Remove empty *_remove()
printk() - isolate KERN_CONT users from ordinary complete lines
sysfs: get rid of some lockdep false positives
Drivers: hv: util: Properly handle version negotiations.
Drivers: hv: Get rid of an unnecessary check in vmbus_prep_negotiate_resp()
memory: tegra{20,30}-mc: Use dev_err_ratelimited()
driver core: Add dev_*_ratelimited() family
Driver Core: don't oops with unregistered driver in driver_find_device()
printk() - restore prefix/timestamp printing for multi-newline strings
printk: add stub for prepend_timestamp()
ARM: tegra30: Make MC optional in Kconfig
ARM: tegra20: Make MC optional in Kconfig
ARM: tegra30: MC: Remove unnecessary BUG*()
ARM: tegra20: MC: Remove unnecessary BUG*()
printk: correctly align __log_buf
ARM: tegra30: Add Tegra Memory Controller(MC) driver
ARM: tegra20: Add Tegra Memory Controller(MC) driver
printk() - restore timestamp printing at console output
printk() - do not merge continuation lines of different threads
...
This series sanitizes the interface to unmap_vma(). The crazy interface
annoyed me no end when I was looking at unmap_single_vma(), which we can
spend quite a lot of time in (especially with loads that have a lot of
small fork/exec's: shell scripts etc).
Moving the nr_accounted calculations to where they belong at least
clarifies things a little. I hope to come back to look at the
performance of this later, but if/when I get back to it I at least don't
have to see the crazy interfaces any more.
* vm-cleanups:
vm: remove 'nr_accounted' calculations from the unmap_vmas() interfaces
vm: simplify unmap_vmas() calling convention
__alloc_contig_migrate_range calls migrate_pages with wrong argument
for migrate_mode. Fix it.
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Minchan Kim <minchan@kernel.org>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
alloc_contig_range() performs memory allocation so it also should keep
track on keeping the correct level of memory watermarks. This commit adds
a call to *_slowpath style reclaim to grab enough pages to make sure that
the final collection of contiguous pages from freelists will not starve
the system.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Michal Nazarewicz <mina86@mina86.com>
Tested-by: Rob Clark <rob.clark@linaro.org>
Tested-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Tested-by: Barry Song <Baohua.Song@csr.com>
This patch extracts common reclaim code from __alloc_pages_direct_reclaim()
function to separate function: __perform_reclaim() which can be later used
by alloc_contig_range().
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Tested-by: Rob Clark <rob.clark@linaro.org>
Tested-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Tested-by: Barry Song <Baohua.Song@csr.com>
There is a race between the min_free_kbytes sysctl, memory hotplug
and transparent hugepage support enablement. Memory hotplug uses a
zonelists_mutex to avoid a race when building zonelists. Reuse it to
serialise watermark updates.
[a.p.zijlstra@chello.nl: Older patch fixed the race with spinlock]
Signed-off-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Tested-by: Barry Song <Baohua.Song@csr.com>
This commit changes various functions that change pages and
pageblocks migrate type between MIGRATE_ISOLATE and
MIGRATE_MOVABLE in such a way as to allow to work with
MIGRATE_CMA migrate type.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Tested-by: Rob Clark <rob.clark@linaro.org>
Tested-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Tested-by: Barry Song <Baohua.Song@csr.com>
The MIGRATE_CMA migration type has two main characteristics:
(i) only movable pages can be allocated from MIGRATE_CMA
pageblocks and (ii) page allocator will never change migration
type of MIGRATE_CMA pageblocks.
This guarantees (to some degree) that page in a MIGRATE_CMA page
block can always be migrated somewhere else (unless there's no
memory left in the system).
It is designed to be used for allocating big chunks (eg. 10MiB)
of physically contiguous memory. Once driver requests
contiguous memory, pages from MIGRATE_CMA pageblocks may be
migrated away to create a contiguous block.
To minimise number of migrations, MIGRATE_CMA migration type
is the last type tried when page allocator falls back to other
migration types when requested.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Tested-by: Rob Clark <rob.clark@linaro.org>
Tested-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Tested-by: Barry Song <Baohua.Song@csr.com>
This commit adds a row for MIGRATE_ISOLATE type to the fallbacks array
which was missing from it. It also, changes the array traversal logic
a little making MIGRATE_RESERVE an end marker. The letter change,
removes the implicit MIGRATE_UNMOVABLE from the end of each row which
was read by __rmqueue_fallback() function.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Tested-by: Rob Clark <rob.clark@linaro.org>
Tested-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Tested-by: Barry Song <Baohua.Song@csr.com>
This commit adds the alloc_contig_range() function which tries
to allocate given range of pages. It tries to migrate all
already allocated pages that fall in the range thus freeing them.
Once all pages in the range are freed they are removed from the
buddy system thus allocated for the caller to use.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Tested-by: Rob Clark <rob.clark@linaro.org>
Tested-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Tested-by: Barry Song <Baohua.Song@csr.com>
This commit exports some of the functions from compaction.c file
outside of it adding their declaration into internal.h header
file so that other mm related code can use them.
This forced compaction.c to always be compiled (as opposed to being
compiled only if CONFIG_COMPACTION is defined) but as to avoid
introducing code that user did not ask for, part of the compaction.c
is now wrapped in on #ifdef.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Tested-by: Rob Clark <rob.clark@linaro.org>
Tested-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Tested-by: Barry Song <Baohua.Song@csr.com>
This commit introduces isolate_freepages_range() function which
generalises isolate_freepages_block() so that it can be used on
arbitrary PFN ranges.
isolate_freepages_block() is left with only minor changes.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Tested-by: Rob Clark <rob.clark@linaro.org>
Tested-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Tested-by: Barry Song <Baohua.Song@csr.com>
This commit creates a map_pages() function which map pages freed
using split_free_pages(). This merely moves some code from
isolate_freepages() so that it can be reused in other places.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Tested-by: Barry Song <Baohua.Song@csr.com>
This commit introduces isolate_migratepages_range() function which
extracts functionality from isolate_migratepages() so that it can be
used on arbitrary PFN ranges.
isolate_migratepages() function is implemented as a simple wrapper
around isolate_migratepages_range().
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Tested-by: Rob Clark <rob.clark@linaro.org>
Tested-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Tested-by: Barry Song <Baohua.Song@csr.com>
Occasionally, testing memcg's move_charge_at_immigrate on rc7 shows
a flurry of hundreds of warnings at kernel/res_counter.c:96, where
res_counter_uncharge_locked() does WARN_ON(counter->usage < val).
The first trace of each flurry implicates __mem_cgroup_cancel_charge()
of mc.precharge, and an audit of mc.precharge handling points to
mem_cgroup_move_charge_pte_range()'s THP handling in commit 12724850e8
("memcg: avoid THP split in task migration").
Checking !mc.precharge is good everywhere else, when a single page is to
be charged; but here the "mc.precharge -= HPAGE_PMD_NR" likely to
follow, is liable to result in underflow (a lot can change since the
precharge was estimated).
Simply check against HPAGE_PMD_NR: there's probably a better
alternative, trying precharge for more, splitting if unsuccessful; but
this one-liner is safer for now - no kernel/res_counter.c:96 warnings
seen in 26 hours.
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I found some kernel messages such as:
SLUB raid5-md127: kmem_cache_destroy called for cache that still has objects.
Pid: 6143, comm: mdadm Tainted: G O 3.4.0-rc6+ #75
Call Trace:
kmem_cache_destroy+0x328/0x400
free_conf+0x2d/0xf0 [raid456]
stop+0x41/0x60 [raid456]
md_stop+0x1a/0x60 [md_mod]
do_md_stop+0x74/0x470 [md_mod]
md_ioctl+0xff/0x11f0 [md_mod]
blkdev_ioctl+0xd8/0x7a0
block_ioctl+0x3b/0x40
do_vfs_ioctl+0x96/0x560
sys_ioctl+0x91/0xa0
system_call_fastpath+0x16/0x1b
Then using kmemleak I found these messages:
unreferenced object 0xffff8800b6db7380 (size 112):
comm "mdadm", pid 5783, jiffies 4294810749 (age 90.589s)
hex dump (first 32 bytes):
01 01 db b6 ad 4e ad de ff ff ff ff ff ff ff ff .....N..........
ff ff ff ff ff ff ff ff 98 40 4a 82 ff ff ff ff .........@J.....
backtrace:
kmemleak_alloc+0x21/0x50
kmem_cache_alloc+0xeb/0x1b0
kmem_cache_open+0x2f1/0x430
kmem_cache_create+0x158/0x320
setup_conf+0x649/0x770 [raid456]
run+0x68b/0x840 [raid456]
md_run+0x529/0x940 [md_mod]
do_md_run+0x18/0xc0 [md_mod]
md_ioctl+0xba8/0x11f0 [md_mod]
blkdev_ioctl+0xd8/0x7a0
block_ioctl+0x3b/0x40
do_vfs_ioctl+0x96/0x560
sys_ioctl+0x91/0xa0
system_call_fastpath+0x16/0x1b
This bug was introduced by commit a8364d5555 ("slub: only IPI CPUs that
have per cpu obj to flush"), which did not include checks for per cpu
partial pages being present on a cpu.
Signed-off-by: majianpeng <majianpeng@gmail.com>
Cc: Gilad Ben-Yossef <gilad@benyossef.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Tested-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Why is there less MemFree than there used to be? It perturbed a test,
so I've just been bisecting linux-next, and now find the offender went
upstream yesterday.
Commit 93278814d3 "mm: fix division by 0 in percpu_pagelist_fraction()"
mistakenly initialized percpu_pagelist_fraction to the sysctl's minimum 8,
which leaves 1/8th of memory on percpu lists (on each cpu??); but most of
us expect it to be left unset at 0 (and it's not then used as a divisor).
MemTotal: 8061476kB 8061476kB 8061476kB 8061476kB 8061476kB 8061476kB
Repetitive test with percpu_pagelist_fraction 8:
MemFree: 6948420kB 6237172kB 6949696kB 6840692kB 6949048kB 6862984kB
Same test with percpu_pagelist_fraction back to 0:
MemFree: 7945000kB 7944908kB 7948568kB 7949060kB 7948796kB 7948812kB
Signed-off-by: Hugh Dickins <hughd@google.com>
[ We really should fix the crazy sysctl interface too, but that's a
separate thing - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge misc fixes from Andrew Morton.
* emailed from Andrew Morton <akpm@linux-foundation.org>: (8 patches)
MAINTAINERS: add maintainer for LED subsystem
mm: nobootmem: fix sign extend problem in __free_pages_memory()
drivers/leds: correct __devexit annotations
memcg: free spare array to avoid memory leak
namespaces, pid_ns: fix leakage on fork() failure
hugetlb: prevent BUG_ON in hugetlb_fault() -> hugetlb_cow()
mm: fix division by 0 in percpu_pagelist_fraction()
proc/pid/pagemap: correctly report non-present ptes and holes between vmas
Systems with 8 TBytes of memory or greater can hit a problem where only
the the first 8 TB of memory shows up. This is due to "int i" being
smaller than "unsigned long start_aligned", causing the high bits to be
dropped.
The fix is to change `i' to unsigned long to match start_aligned
and end_aligned.
Thanks to Jack Steiner for assistance tracking this down.
Signed-off-by: Russ Anderson <rja@sgi.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Gavin Shan <shangw@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When the last event is unregistered, there is no need to keep the spare
array anymore. So free it to avoid memory leak.
Signed-off-by: Sha Zhengju <handai.szj@taobao.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Reviewed-by: Kirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 66aebce747 ("hugetlb: fix race condition in hugetlb_fault()")
added code to avoid a race condition by elevating the page refcount in
hugetlb_fault() while calling hugetlb_cow().
However, one code path in hugetlb_cow() includes an assertion that the
page count is 1, whereas it may now also have the value 2 in this path.
The consensus is that this BUG_ON has served its purpose, so rather than
extending it to cover both cases, we just remove it.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Acked-by: Hillf Danton <dhillf@gmail.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: <stable@vger.kernel.org> [3.0.29+, 3.2.16+, 3.3.3+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
percpu_pagelist_fraction_sysctl_handler() has only considered -EINVAL as
a possible error from proc_dointvec_minmax().
If any other error is returned, it would proceed to divide by zero since
percpu_pagelist_fraction wasn't getting initialized at any point. For
example, writing 0 bytes into the proc file would trigger the issue.
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Reviewed-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kmemleak tracks the percpu allocations via a specific API and the
originally allocated areas must be removed from kmemleak (via
kmemleak_free). The code was already doing this for SMP systems.
Reported-by: Sami Liedes <sami.liedes@iki.fi>
Cc: Tejun Heo <tj@kernel.org>
Cc: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
pcpu_embed_first_chunk() allocates memory for each node, copies percpu
data and frees unused portions of it before proceeding to the next
group. This assumes that allocations for different nodes doesn't
overlap; however, depending on memory topology, the bootmem allocator
may end up allocating memory from a different node than the requested
one which may overlap with the portion freed from one of the previous
percpu areas. This leads to percpu groups for different nodes
overlapping which is a serious bug.
This patch separates out copy & partial free from the allocation loop
such that all allocations are complete before partial frees happen.
This also fixes overlapping frees which could happen on allocation
failure path - out_free_areas path frees whole groups but the groups
could have portions freed at that point.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Reported-by: "Pavel V. Panteleev" <pp_84@mail.ru>
Tested-by: "Pavel V. Panteleev" <pp_84@mail.ru>
LKML-Reference: <E1SNhwY-0007ui-V7.pp_84-mail-ru@f220.mail.ru>
Pull two percpu fixes from Tejun Heo:
"One adds missing KERN_CONT on split printk()s and the other makes
the percpu allocator avoid using PMD_SIZE as atom_size on x86_32.
Using PMD_SIZE led to vmalloc area exhaustion on certain
configurations (x86_32 android) and the only cost of using PAGE_SIZE
instead is static percpu area not being aligned to large page
mapping."
* 'for-3.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu, x86: don't use PMD_SIZE as embedded atom_size on 32bit
percpu: use KERN_CONT in pcpu_dump_alloc_info()