Rework the SuperH Mobile sleep code from including
board specific code to allowing each board to provide
pre/post code snippets. These snippets should contain
sdram management code to enter and leave self-refresh.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add code to allow boards registering self-contained
functions for going to/from self-refresh. At this
point the board code is unused. When all supported
boards have been converted then the new sleep code
will make use of these functions.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds atomic notifier chains for pre/post
sleep events. Useful for cpu code and boards that
need to save and restore register state before and
after entering a sleep mode.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds in preliminary support for the SH-4A performance counters.
Presently only the first 2 counters are supported, as these are the ones
of the most interest to the perf tool and end users. Counter chaining is
not presently handled, so these are simply implemented as 32-bit
counters.
This also establishes a perf event support framework for other hardware
counters, which the existing SH-4 oprofile code will migrate over to as
the SH-4A support evolves.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Leaving this configurable caused more trouble than it was ever worth, so
just make it explicit. Boards that are verified one way or the other can
fix up their selects accordingly. We presently default to non-coherent
for most platforms.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This moves the current dma_alloc/free_coherent() calls to a generic
variant and plugs them in for the nommu default. Other variants can
override the defaults in the dma mapping ops directly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
In the past these were simply wrapping to barrier() which was sufficient
on SH SMP platforms predating SH-4A. Unfortunately due to ll/sc semantics
an explicit synco is needed in these cases, which is sorted for us by
just switching these over to smp_mb(). smp_mb() also has the benefit of
being wrapped to barrier() in the UP and non-SH4A cases, so old behaviour
is maintained for those parts.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This simplifies the irqflags support by switching over to the asm-generic
version. The necessary support functions are brought out-of-line for both
SHcompact and SHmedia instruction sets.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This code was added for some ancient SH-4 solution engines with peculiar
boot ROMs that did silly things to the UBC MSTP bits. None of these have
been in the wild for years, and these days the clock framework wraps up
the MSTP bits, meaning that the UBC code is one of the few interfaces
that is stomping MSTP bits underneath the clock framework. At this point
the risks far outweigh any benefit this code provided, so just kill it
off.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This enables SCHED_MC support for SH-X3 multi-cores. Presently this is
just a simple wrapper around the possible map, but this allows for
tying in support for some of the more exotic NUMA clusters where we can
actually do something with the topology.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This does a bit of chainsawing of the idle loop code to get light sleep
working on SMP. Previously this was forcing secondary CPUs in to sleep
mode with them not coming back if they didn't have their own local
timers. Given that we use clockevents broadcasting by default, the CPU
managing the clockevents can't have IRQs disabled before entering its
sleep state.
This unfortunately leaves us with the age-old need_resched() race in
between local_irq_enable() and cpu_sleep(), but at present this is
unavoidable. After some more experimentation it may be possible to layer
on SR.BL bit manipulation over top of this scheme to inhibit the race
condition, but given the current potential for missing wakeups, this is
left as a future exercise.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This plugs in support for NMI counting per-CPU via irq_cpustat_t.
Modelled after the x86 implementation.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Replace TIF_RESTORE_SIGMASK with TS_RESTORE_SIGMASK and define our own
set_restore_sigmask() function. This saves the costly SMP-safe set_bit
operation, which we do not need for the sigmask flag since TIF_SIGPENDING
always has to be set too.
Based on the x86 and powerpc change.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Despite being located in the ftrace header, the CALLER_ADDRx definitions
are used by generic code. As such, we have to provide it generically, and
given that there is no real dependence on ftrace in the first place, the
definitions can just be moved out.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Extend the sh_eth driver to allow passing the mac address
using the platform data structure. This to simplify board
setup code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables us to build the dwarf unwinder both with modules enabled and
disabled in addition to reducing code size in the latter case. The
helpers are also consolidated, and modified to resemble the BUG module
helpers.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This splits out the unwinder implementation and adds a new
return_address() abstraction modelled after the ARM code. The DWARF
unwinder is tied in to this, returning NULL otherwise in the case of
being unable to support arbitrary depths.
This enables us to get correct behaviour with the unwinder enabled,
as well as disabling the arbitrary depth support when frame pointers are
enabled, as arbitrary depths with __builtin_return_address() are not
supported regardless.
With this abstraction it's also possible to layer on a simplified
implementation with frame pointers in the event that the unwinder isn't
enabled, although this is left as a future exercise.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The major reason for implementing the DWARF unwinder in the first place
was so that we could stop using __builtin_return_address(n), which
doesn't work on SH for n > 0.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
If we broke out of the while (1) loop because the return address of
"frame" was zero, then "frame" needs to be free'd before we return.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Pass a module's .eh_frame section to the DWARF unwinder at module load
time so that the section's FDEs and CIEs can be registered with the
DWARF unwinder. This allows us to unwind the stack through module code
when generating backtraces.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
The initialisation process differs for CONFIG_PMB and for
CONFIG_PMB_FIXED. For CONFIG_PMB_FIXED we need to register the PMB
entries that were allocated by the bootloader.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Eventually we'll have complete control over what physical memory gets
mapped where and we can probably do other interesting things. For now
though, when the MMU is in 32-bit mode, we map physical memory into the
P1 and P2 virtual address ranges with the same semantics as they have in
29-bit mode.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There's no need to export the internal PMB functions for allocating,
freeing and modifying PMB entries, etc. This way we can restrict the
interface for PMB.
Also remove the static from pmb_init() so that we have more freedom in
setting up the initial PMB entries and turning on MMU 32bit mode.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
To allow the MMU to be switched between 29bit and 32bit mode at runtime
some constants need to swapped for functions that return a runtime
value.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Replace the use of PHYSADDR() with __pa(). PHYSADDR() is based on the
idea that all addresses in P1SEG are untranslated, so we can access an
address's physical page as an offset from P1SEG. This doesn't work for
CONFIG_PMB/CONFIG_PMB_FIXED because pages in P1SEG and P2SEG are used
for PMB mappings and so can be translated to any physical address.
Likewise, replace a P1SEGADDR() use with virt_to_phys().
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'for-linus' of git://neil.brown.name/md: (97 commits)
md: raid-1/10: fix RW bits manipulation
md: remove unnecessary memset from multipath.
md: report device as congested when suspended
md: Improve name of threads created by md_register_thread
md: remove sparse warnings about lock context.
md: remove sparse waring "symbol xxx shadows an earlier one"
async_tx/raid6: add missing dma_unmap calls to the async fail case
ioat3: fix uninitialized var warnings
drivers/dma/ioat/dma_v2.c: fix warnings
raid6test: fix stack overflow
ioat2: clarify ring size limits
md/raid6: cleanup ops_run_compute6_2
md/raid6: eliminate BUG_ON with side effect
dca: module load should not be an error message
ioat: driver version 4.0
dca: registering requesters in multiple dca domains
async_tx: remove HIGHMEM64G restriction
dmaengine: sh: Add Support SuperH DMA Engine driver
dmaengine: Move all map_sg/unmap_sg for slave channel to its client
fsldma: Add DMA_SLAVE support
...
Bye-bye Performance Counters, welcome Performance Events!
In the past few months the perfcounters subsystem has grown out its
initial role of counting hardware events, and has become (and is
becoming) a much broader generic event enumeration, reporting, logging,
monitoring, analysis facility.
Naming its core object 'perf_counter' and naming the subsystem
'perfcounters' has become more and more of a misnomer. With pending
code like hw-breakpoints support the 'counter' name is less and
less appropriate.
All in one, we've decided to rename the subsystem to 'performance
events' and to propagate this rename through all fields, variables
and API names. (in an ABI compatible fashion)
The word 'event' is also a bit shorter than 'counter' - which makes
it slightly more convenient to write/handle as well.
Thanks goes to Stephane Eranian who first observed this misnomer and
suggested a rename.
User-space tooling and ABI compatibility is not affected - this patch
should be function-invariant. (Also, defconfigs were not touched to
keep the size down.)
This patch has been generated via the following script:
FILES=$(find * -type f | grep -vE 'oprofile|[^K]config')
sed -i \
-e 's/PERF_EVENT_/PERF_RECORD_/g' \
-e 's/PERF_COUNTER/PERF_EVENT/g' \
-e 's/perf_counter/perf_event/g' \
-e 's/nb_counters/nb_events/g' \
-e 's/swcounter/swevent/g' \
-e 's/tpcounter_event/tp_event/g' \
$FILES
for N in $(find . -name perf_counter.[ch]); do
M=$(echo $N | sed 's/perf_counter/perf_event/g')
mv $N $M
done
FILES=$(find . -name perf_event.*)
sed -i \
-e 's/COUNTER_MASK/REG_MASK/g' \
-e 's/COUNTER/EVENT/g' \
-e 's/\<event\>/event_id/g' \
-e 's/counter/event/g' \
-e 's/Counter/Event/g' \
$FILES
... to keep it as correct as possible. This script can also be
used by anyone who has pending perfcounters patches - it converts
a Linux kernel tree over to the new naming. We tried to time this
change to the point in time where the amount of pending patches
is the smallest: the end of the merge window.
Namespace clashes were fixed up in a preparatory patch - and some
stylistic fallout will be fixed up in a subsequent patch.
( NOTE: 'counters' are still the proper terminology when we deal
with hardware registers - and these sed scripts are a bit
over-eager in renaming them. I've undone some of that, but
in case there's something left where 'counter' would be
better than 'event' we can undo that on an individual basis
instead of touching an otherwise nicely automated patch. )
Suggested-by: Stephane Eranian <eranian@google.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Paul Mackerras <paulus@samba.org>
Reviewed-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: <linux-arch@vger.kernel.org>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (262 commits)
sh: mach-ecovec24: Add user debug switch support
sh: Kill off unused se_skipped in alignment trap notification code.
sh: Wire up HAVE_SYSCALL_TRACEPOINTS.
video: sh_mobile_lcdcfb: use both register sets for display panning
video: sh_mobile_lcdcfb: implement display panning
sh: Fix up sh7705 flush_dcache_page() build.
sh: kfr2r09: document the PLL/FLL <-> RF relationship.
sh: mach-ecovec24: need asm/clock.h.
sh: mach-ecovec24: deassert usb irq on boot.
sh: Add KEYSC support for EcoVec24
sh: add kycr2_delay for sh_keysc
sh: cpufreq: Include CPU id in info messages.
sh: multi-evt support for SH-X3 proto CPU.
sh: clkfwk: remove bogus set_bus_parent() from SH7709.
sh: Fix the indication point of the liquid crystal of AP-325RXA(AP3300)
sh: Add EcoVec24 romImage defconfig
sh: USB disable process is needed if romImage boot for EcoVec24
sh: EcoVec24: add HIZA setting for LED
sh: EcoVec24: write MAC address in boot
sh: Add romImage support for EcoVec24
...
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (37 commits)
sched: Fix SD_POWERSAVING_BALANCE|SD_PREFER_LOCAL vs SD_WAKE_AFFINE
sched: Stop buddies from hogging the system
sched: Add new wakeup preemption mode: WAKEUP_RUNNING
sched: Fix TASK_WAKING & loadaverage breakage
sched: Disable wakeup balancing
sched: Rename flags to wake_flags
sched: Clean up the load_idx selection in select_task_rq_fair
sched: Optimize cgroup vs wakeup a bit
sched: x86: Name old_perf in a unique way
sched: Implement a gentler fair-sleepers feature
sched: Add SD_PREFER_LOCAL
sched: Add a few SYNC hint knobs to play with
sched: Fix sync wakeups again
sched: Add WF_FORK
sched: Rename sync arguments
sched: Rename select_task_rq() argument
sched: Feature to disable APERF/MPERF cpu_power
x86: sched: Provide arch implementations using aperf/mperf
x86: Add generic aperf/mperf code
x86: Move APERF/MPERF into a X86_FEATURE
...
Fix up trivial conflict in arch/x86/include/asm/processor.h due to
nearby addition of amd_get_nb_id() declaration from the EDAC merge.
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (75 commits)
PCI hotplug: clean up acpi_run_hpp()
PCI hotplug: acpiphp: use generic pci_configure_slot()
PCI hotplug: shpchp: use generic pci_configure_slot()
PCI hotplug: pciehp: use generic pci_configure_slot()
PCI hotplug: add pci_configure_slot()
PCI hotplug: clean up acpi_get_hp_params_from_firmware() interface
PCI hotplug: acpiphp: don't cache hotplug_params in acpiphp_bridge
PCI hotplug: acpiphp: remove superfluous _HPP/_HPX evaluation
PCI: Clear saved_state after the state has been restored
PCI PM: Return error codes from pci_pm_resume()
PCI: use dev_printk in quirk messages
PCI / PCIe portdrv: Fix pcie_portdrv_slot_reset()
PCI Hotplug: convert acpi_pci_detect_ejectable() to take an acpi_handle
PCI Hotplug: acpiphp: find bridges the easy way
PCI: pcie portdrv: remove unused variable
PCI / ACPI PM: Propagate wake-up enable for devices w/o ACPI support
ACPI PM: Replace wakeup.prepared with reference counter
PCI PM: Introduce device flag wakeup_prepared
PCI / ACPI PM: Rework some debug messages
PCI PM: Simplify PCI wake-up code
...
Fixed up conflict in arch/powerpc/kernel/pci_64.c due to OF device tree
scanning having been moved and merged for the 32- and 64-bit cases. The
'needs_freset' initialization added in 6e19314cc ("PCI/powerpc: support
PCIe fundamental reset") is now in arch/powerpc/kernel/pci_of_scan.c.
Sysbench thinks SD_BALANCE_WAKE is too agressive and kbuild doesn't
really mind too much, SD_BALANCE_NEWIDLE picks up most of the
slack.
On a dual socket, quad core, dual thread nehalem system:
sysbench (--num_threads=16):
SD_BALANCE_WAKE-: 13982 tx/s
SD_BALANCE_WAKE+: 15688 tx/s
kbuild (-j16):
SD_BALANCE_WAKE-: 47.648295846 seconds time elapsed ( +- 0.312% )
SD_BALANCE_WAKE+: 47.608607360 seconds time elapsed ( +- 0.026% )
(same within noise)
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This is necessary to get ftrace syscall tracing working again.. a fairly
trivial and mechanical change. The one benefit is that this can also be
enabled on sh64, despite not having its own ftrace port.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
If we're looking to place a new task, we might as well find the
idlest position _now_, not 1 tick ago.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Make the idle balancer more agressive, to improve a
x264 encoding workload provided by Jason Garrett-Glaser:
NEXT_BUDDY NO_LB_BIAS
encoded 600 frames, 252.82 fps, 22096.60 kb/s
encoded 600 frames, 250.69 fps, 22096.60 kb/s
encoded 600 frames, 245.76 fps, 22096.60 kb/s
NO_NEXT_BUDDY LB_BIAS
encoded 600 frames, 344.44 fps, 22096.60 kb/s
encoded 600 frames, 346.66 fps, 22096.60 kb/s
encoded 600 frames, 352.59 fps, 22096.60 kb/s
NO_NEXT_BUDDY NO_LB_BIAS
encoded 600 frames, 425.75 fps, 22096.60 kb/s
encoded 600 frames, 425.45 fps, 22096.60 kb/s
encoded 600 frames, 422.49 fps, 22096.60 kb/s
Peter pointed out that this is better done via newidle_idx,
not via LB_BIAS, newidle balancing should look for where
there is load _now_, not where there was load 2 ticks ago.
Worst-case latencies are improved as well as no buddies
means less vruntime spread. (as per prior lkml discussions)
This change improves kbuild-peak parallelism as well.
Reported-by: Jason Garrett-Glaser <darkshikari@gmail.com>
Signed-off-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1253011667.9128.16.camel@marge.simson.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When merging select_task_rq_fair() and sched_balance_self() we lost
the use of wake_idx, restore that and set them to 0 to make wake
balancing more aggressive.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The problem with wake_idle() is that is doesn't respect things like
cpu_power, which means it doesn't deal well with SMT nor the recent
RT interaction.
To cure this, it needs to do what sched_balance_self() does, which
leads to the possibility of merging select_task_rq_fair() and
sched_balance_self().
Modify sched_balance_self() to:
- update_shares() when walking up the domain tree,
(it only called it for the top domain, but it should
have done this anyway), which allows us to remove
this ugly bit from try_to_wake_up().
- do wake_affine() on the smallest domain that contains
both this (the waking) and the prev (the wakee) cpu for
WAKE invocations.
Then use the top-down balance steps it had to replace wake_idle().
This leads to the dissapearance of SD_WAKE_BALANCE and
SD_WAKE_IDLE_FAR, with SD_WAKE_IDLE replaced with SD_BALANCE_WAKE.
SD_WAKE_AFFINE needs SD_BALANCE_WAKE to be effective.
Touch all topology bits to replace the old with new SD flags --
platforms might need re-tuning, enabling SD_BALANCE_WAKE
conditionally on a NUMA distance seems like a good additional
feature, magny-core and small nehalem systems would want this
enabled, systems with slow interconnects would not.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Early clock initialization sets up PLL/FLL values for optimal RF
behaviour. As this relationship is presently undocumented, we document
this in the script so the rationale is apparent.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
After KYCR2 is set, udelay might become necessary if there are only a
small number of keys attached. This patch introduces an optional delay
through the platform data to address this problem.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
when you use romImage on EcoVec24, 1st Linux will enable USB device.
But no-one disable it.
So re-started Linux will get interrupt before USB driver is attached.
This patch disable USB device at first
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
romimage macros which are used in kfr2r09 is very useful for other board.
This patch divides kfr2r09's romimage.h into
romimage-macros and partner-jet-setup.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This was #define'd as 0 on all platforms, so let's get rid of it.
This change makes pci_scan_slot() slightly easier to read.
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Tony Luck <tony.luck@intel.com>
Cc: David Howells <dhowells@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Russell King <linux@arm.linux.org.uk>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In the SMP VIPT case the page copy/clear ops still perform colouring,
care needs to be taken that CPUs don't end up stepping on each other,
so we give them a bit of room to work with.
At the same time, we reduce the worst-case colouring given that these
pages are always consumed.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This supported all DMA channels, and it was tested in SH7722,
SH7780, SH7785 and SH7763.
This can not use with SH DMA API.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Reviewed-by: Matt Fleming <matt@console-pimps.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This fixes up the kmap_coherent/kunmap_coherent() interface for recent
changes both in the page fault path and the shared cache flushers, as
well as adding in some optimizations.
One of the key things to note here is that the TLB flush itself is
deferred until the unmap, and the call in to update_mmu_cache() itself
goes away, relying on the regular page fault path to handle the lazy
dcache writeback if necessary.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The kgdb stub has traditionally tied in to the NMI slot, and manually
handled debounce. Now that we have a generic way to do this instead, all
of the stub-specific debounce silliness can be killed off.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements support for NMI debugging that was shamelessly copied
from the avr32 port. A bit of special magic is needed in the interrupt
exception path given that the NMI exception handler is stubbed in to the
regular exception handling table despite being reported in INTEVT. So we
mangle the lookup and kick off an EXPEVT-style exception dispatch from
the INTEVT path for exceptions that do_IRQ() has no chance of handling.
As a result, we also drop the evt2irq() conversion from the do_IRQ() path
and just do it in assembly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Some unaligned accesses are completely expected. For example, the
trapped_io code uses the unaligned access fixup code path so there's no
need to warn about having to fixup the unaligned access.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The method of ETHER_LINK pin is board dependence.
This patch adding paramters are:
- no_ether_link : If set to 1, do not use ETHER_LINK
- ether_link_active_low : If set to 1, ETHER_LINK is active low.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is supposed to be the equivalent of __NR_syscalls, not
__NR_syscalls -1. The x86 code this was based on had simply fallen
out of sync at the time this was implemented. Fix it up now.
As a result, tracing of __NR_perf_counter_open works as advertised.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
sys_cacheflush should return with EINVAL if the cache parameter is not
one of ICACHE, DCACHE or BCACHE.
So, we need to include 0 in the first check.
It also adds the three definitions above as wrapper of the existent macros.
PS: ltp cacheflush01 test now passes.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Adds a system call to allow user code to flush code from the cache.
You can use instructions for the data side, but the iside can
only be done by a flush ROM which really only works with a direct
mapped cache. The later SH4's have 2 way Iside, so this call allows
a portable way to flush the cache.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Reading from the ROM is not a good idea as it could disturb some
flash operation that it is in progress.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The SH instruction set has several instructions which accept an 8 bit
immediate operand. For logical instructions this operand is zero extended,
for arithmetic instructions the operand is sign extended. After adding an
option to the assembler to check this, it was found that several pieces
of assembly code were assuming this behaviour, and in one case
getting it wrong.
So this patch explicitly sign extends any immediate operands, which makes
it obvious what is happening, and fixes the one case which got it wrong.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The synopsys PCI cell used in the later STMicro chips requires code to
be run in order to do IO cycles, rather than just memory mapping the IO
space. Rather than extending the existing SH infrastructure to allow
this, use the GENERIC_IOMAP implmentation to save re-inventing the
wheel.
This set of changes allows the SH to be built with GENERIC_IOMAP
enabled, it just ifdef's out the functions provided by the GENERIC_IOMAP
implementation, and provides a few required missing functions.
Signed-off-by: David McKay <david.mckay@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch is V3 of the SuperH Mobile Runtime PM platform bus
implentation matching Rafael's Runtime PM v16.
The code gets invoked from the SuperH specific Runtime PM
platform bus functions that override the weak symbols for:
- platform_pm_runtime_suspend()
- platform_pm_runtime_resume()
- platform_pm_runtime_idle()
This Runtime PM implementation performs two levels of power
management. At the time of platform bus runtime suspend the
clock to the device is stopped instantly. Later on if all
devices within the power domain has their clocks stopped
then the device driver ->runtime_suspend() callbacks are
used to save hardware register state for each device.
Device driver ->runtime_suspend() calls are scheduled from
cpuidle context using platform_pm_runtime_suspend_idle().
When all devices have been fully suspended the processor
is allowed to enter deep sleep from cpuidle.
The runtime resume operation turns on clocks and also
restores registers if needed. It is worth noting that the
devices start in a suspended state and the device driver
is responsible for calling runtime resume before accessing
the actual hardware.
In this particular platform bus implementation runtime
resume is not allowed from interrupt context. Runtime
suspend is however allowed from interrupt context as
long as the synchronous functions are avoided.
[ updated for v17 -- PFM. ]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
sh64 does not yet support GENERIC_BUG, but still wants unwinder support.
Alias UNWINDER_BUG and UNWINDER_BUG_ON to their BUG counterparts until
the conversion to GENERIC_BUG is completed.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This simplifies the unwinder trap handling, dropping the use of the
special trapa vector and simply piggybacking on top of the BUG support. A
new BUGFLAG_UNWINDER is added for flagging the unwinder fault, before
continuing on with regular BUG dispatch.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Allow a DWARF register to have an undefined value. When applied to the
DWARF return address register this lets lets us label a function as
having no direct caller, e.g. kernel_thread_helper().
Signed-off-by: Matt Fleming <matt@console-pimps.org>
We can't assume that if we execute the unwinder code and the unwinder
was already running that it has faulted. Clearly two kernel threads can
invoke the unwinder at the same time and may be running simultaneously.
The previous approach used BUG() and BUG_ON() in the unwinder code to
detect whether the unwinder was incapable of unwinding the stack, and
that the next available unwinder should be used instead. A better
approach is to explicitly invoke a trap handler to switch unwinders when
the current unwinder cannot continue.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
The handling of DW_CFA_val_offset ops was incorrectly using the
DWARF_REG_OFFSET flag but the register's value cannot be calculated
using the DWARF_REG_OFFSET method. Create a new flag to indicate that a
different method must be used to calculate the register's value even
though there is no implementation for DWARF_VAL_OFFSET yet; it's mainly
just a place holder.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Plug a memory leak in dwarf_unwinder_dump() where we didn't free the
memory that we had previously allocated for the DWARF frames and DWARF
registers.
Now is also a opportune time to implement our own mempool and kmem
cache. It's a good idea to have a certain number of frame and register
objects in reserve at all times, so that we are guaranteed to have our
allocation satisfied even when memory is scarce. Since we have pools to
allocate from we can implement the registers for each frame as a linked
list as opposed to a sparsely populated array. Whilst it's true that the
lookup time for a linked list is larger than for arrays, there's only
usually a maximum of 8 registers per frame. So the overhead isn't that
much of a concern.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
This does a bit of rework for making the cache flushers SMP-aware. The
function pointer-based flushers are renamed to local variants with the
exported interface being commonly implemented and wrapping as necessary.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
All CPU-specific overloads are done at runtime now, so this common header
can go away and simply be folded back in to asm/ version.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a P1 jump to the the kfr2r09 romimage code. With this
patch applied the initial zImage assembly code will run
with instruction cache enabled.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add instruction cache and TLB invalidation code for the
the kfr2r09 romimage target.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When get_mmu_context() runs out of new ASIDs it flushes the TLB and
wraps around. Despite the fact the ASIDs are tracked per-CPU, a global
TLB flush was being used. Switch this over to a local one, as matches
the intent.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
As an excellent indicator of how much testing the DSP code gets, a couple
of rather glaring bugs in the DSP save/restore paths were found:
- In the DSP restore case a0 needs to be popped off before a0g,
or the value of a0g is clobbered by the MSB of a0 in the case
of sign extension.
- Beyond that, the save and restore orders were out of sync,
so this fixes that up as well. At the same time, we switch over
to using movs.l for both the save and restore of the general DSP
registers as opposed to using sts.l (which was initially put in
place to work around a bug in ancient binutils versions which
the kernel no longer supports).
Reported-by: Chee Soon Yip <yip.cheesoon@renesas.com>
Cc: Chu Lih Kwek <kwek.chulih@renesas.com>,
Cc: General Lai <general.lai@renesas.com>,
Cc: Robert Cozens <Robert.Cozens@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
While most platforms implement LED banks in sets of 8/16/32, some use
different configurations. This adds a LED mask to the heartbeat platform
data to allow platforms to constrain the bitmap, which is otherwise
derived from the register size.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
FLLFRQ setting is needed to use correct PLL clock for kfr2409.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This moves the initialization over to an early_initcall(). This fixes up
some lockdep interaction issues. At the same time, kill off some
superfluous locking in the init path.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Also, remove the "fix" to DW_CFA_def_cfa_register where we reset the
frame's cfa_offset to 0. This action is incorrect when handling
DW_CFA_def_cfa_register as the DWARF spec specifically states that the
previous contents of cfa_offset should be used with the new
register. The reason that I thought cfa_offset should be reset to 0 was
because it was being assigned a bogus value prior to executing the
DW_CFA_def_cfa_register op. It turns out that the bogus cfa_offset value
came from interpreting .cfi_escape pseudo-ops (those used by the GNU
extensions) as CFA_DW_def_cfa ops.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
The caches enabled case needs more work, but is presently broken
regardless, so this can be done incrementally.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm