Let's nip the code duplication in the bud :)
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the output transform returns EINPROGRESS due to async operation we'll
free the skb the straight away as if it were an error. This patch fixes
that so that the skb is freed when the async operation completes.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to RFC4303, section 3.3.3 we need to drop outgoing packets which
cause the replay counter to overflow:
3.3.3. Sequence Number Generation
The sender's counter is initialized to 0 when an SA is established.
The sender increments the sequence number (or ESN) counter for this
SA and inserts the low-order 32 bits of the value into the Sequence
Number field. Thus, the first packet sent using a given SA will
contain a sequence number of 1.
If anti-replay is enabled (the default), the sender checks to ensure
that the counter has not cycled before inserting the new value in the
Sequence Number field. In other words, the sender MUST NOT send a
packet on an SA if doing so would cause the sequence number to cycle.
An attempt to transmit a packet that would result in sequence number
overflow is an auditable event. The audit log entry for this event
SHOULD include the SPI value, current date/time, Source Address,
Destination Address, and (in IPv6) the cleartext Flow ID.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a number of new IPsec audit events to meet the auditing
requirements of RFC4303. This includes audit hooks for the following events:
* Could not find a valid SA [sections 2.1, 3.4.2]
. xfrm_audit_state_notfound()
. xfrm_audit_state_notfound_simple()
* Sequence number overflow [section 3.3.3]
. xfrm_audit_state_replay_overflow()
* Replayed packet [section 3.4.3]
. xfrm_audit_state_replay()
* Integrity check failure [sections 3.4.4.1, 3.4.4.2]
. xfrm_audit_state_icvfail()
While RFC4304 deals only with ESP most of the changes in this patch apply to
IPsec in general, i.e. both AH and ESP. The one case, integrity check
failure, where ESP specific code had to be modified the same was done to the
AH code for the sake of consistency.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a number of small but potentially troublesome things in the
XFRM/IPsec code:
* Use the 'audit_enabled' variable already in include/linux/audit.h
Removed the need for extern declarations local to each XFRM audit fuction
* Convert 'sid' to 'secid' everywhere we can
The 'sid' name is specific to SELinux, 'secid' is the common naming
convention used by the kernel when refering to tokenized LSM labels,
unfortunately we have to leave 'ctx_sid' in 'struct xfrm_sec_ctx' otherwise
we risk breaking userspace
* Convert address display to use standard NIP* macros
Similar to what was recently done with the SPD audit code, this also also
includes the removal of some unnecessary memcpy() calls
* Move common code to xfrm_audit_common_stateinfo()
Code consolidation from the "less is more" book on software development
* Proper spacing around commas in function arguments
Minor style tweak since I was already touching the code
Signed-off-by: Paul Moore <paul.moore@hp.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This statistics is shown factor dropped by transformation
at /proc/net/xfrm_stat for developer.
It is a counter designed from current transformation source code
and defined as linux private MIB.
See Documentation/networking/xfrm_proc.txt for the detail.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 specific thing is wrongly removed from transformation at net-2.6.25.
This patch recovers it with current design.
o Update "path" of xfrm_dst since IPv6 transformation should
care about routing changes. It is required by MIPv6 and
off-link destined IPsec.
o Rename nfheader_len which is for non-fragment transformation used by
MIPv6 to rt6i_nfheader_len as IPv6 name space.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
While merging the IPsec output path I moved the encapsulation output
operation to the top of the loop so that it sits outside of the locked
section. Unfortunately in doing so it now sits in front of the space
check as well which could be a fatal error.
This patch rearranges the calls so that the space check happens as
the thing on the output path.
This patch also fixes an incorrect goto should the encapsulation output
fail.
Thanks to Kazunori MIYAZAWA for finding this bug.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The _find calls calculate the hash value using the
xfrm_state_hmask, without the xfrm_state_lock. But the
value of this mask can change in the _resize call under
the state_lock, so we risk to fail in finding the desired
entry in hash.
I think, that the hash value is better to calculate
under the state lock.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Further testing shows that my ICMP relookup patch can cause xfrm_lookup
to return zero on error which isn't very nice since it leads to the caller
dying on null pointer dereference. The bug is due to not setting err
to ENOENT just before we leave xfrm_lookup in case of no policy.
This patch moves the err setting to where it should be.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 4301 requires us to relookup ICMP traffic that does not match any
policies using the reverse of its payload. This patch implements this
for ICMP traffic that originates from or terminates on localhost.
This is activated on outbound with the new policy flag XFRM_POLICY_ICMP,
and on inbound by the new state flag XFRM_STATE_ICMP.
On inbound the policy check is now performed by the ICMP protocol so
that it can repeat the policy check where necessary.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 4301 requires us to relookup ICMP traffic that does not match any
policies using the reverse of its payload. This patch adds the functions
xfrm_decode_session_reverse and xfrmX_policy_check_reverse so we can get
the reverse flow to perform such a lookup.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces an enum for bits in the flags argument of xfrm_lookup.
This is so that we can cram more information into it later.
Since all current users use just the values 0 and 1, XFRM_LOOKUP_WAIT has
been added with the value 1 << 0 to represent the current meaning of flags.
The test in __xfrm_lookup has been changed accordingly.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the xfrm_input_state helper function which returns the
current xfrm state being processed on the input path given an sk_buff.
This is currently only used by xfrm_input but will be used by ESP upon
asynchronous resumption.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
single list_head variable initialized with LIST_HEAD_INIT could almost
always can be replaced with LIST_HEAD declaration, this shrinks the code
and looks better.
Signed-off-by: Denis Cheng <crquan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move dst entries to a namespace loopback to catch refcounting leaks.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When merging the input paths of IPsec I accidentally left a hard-coded
AF_INET for the state lookup call. This broke IPv6 obviously. This
patch fixes by getting the input callers to specify the family through
skb->cb.
Credit goes to Kazunori Miyazawa for diagnosing this and providing an
initial patch.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the netmask/prefix-length of an IPsec SPD entry is not included in
any of the SPD related audit messages. This can cause a problem when the
audit log is examined as the netmask/prefix-length is vital in determining
what network traffic is affected by a particular SPD entry. This patch fixes
this problem by adding two additional fields, "src_prefixlen" and
"dst_prefixlen", to the SPD audit messages to indicate the source and
destination netmasks. These new fields are only included in the audit message
when the netmask/prefix-length is less than the address length, i.e. the SPD
entry applies to a network address and not a host address.
Example audit message:
type=UNKNOWN[1415] msg=audit(1196105849.752:25): auid=0 \
subj=root:system_r:unconfined_t:s0-s0:c0.c1023 op=SPD-add res=1 \
src=192.168.0.0 src_prefixlen=24 dst=192.168.1.0 dst_prefixlen=24
In addition, this patch also fixes a few other things in the
xfrm_audit_common_policyinfo() function. The IPv4 string formatting was
converted to use the standard NIPQUAD_FMT constant, the memcpy() was removed
from the IPv6 code path and replaced with a typecast (the memcpy() was acting
as a slow, implicit typecast anyway), and two local variables were created to
make referencing the XFRM security context and selector information cleaner.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007/11/26, Patrick McHardy <kaber@trash.net>:
> How about also switching vmalloc/get_free_pages to GFP_ZERO
> and getting rid of the memset entirely while you're at it?
>
xfrm_hash: kmalloc + memset conversion to kzalloc
fix to avoid memset entirely.
Signed-off-by: Joonwoo Park <joonwpark81@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
After changeset:
[NETFILTER]: Introduce NF_INET_ hook values
It always evaluates to NF_INET_POST_ROUTING.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for async resumptions on input. To do so, the
transform would return -EINPROGRESS and subsequently invoke the
function xfrm_input_resume to resume processing.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nhoff field isn't actually necessary in xfrm_input. For tunnel
mode transforms we now throw away the output IP header so it makes no
sense to fill in the nexthdr field. For transport mode we can now let
the function transport_finish do the setting and it knows where the
nexthdr field is.
The only other thing that needs the nexthdr field to be set is the
header extraction code. However, we can simply move the protocol
extraction out of the generic header extraction.
We want to minimise the amount of info we have to carry around between
transforms as this simplifies the resumption process for async crypto.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently x->lastused is u64 which means that it cannot be
read/written atomically on all architectures. David Miller observed
that the value stored in it is only an unsigned long which is always
atomic.
So based on his suggestion this patch changes the internal
representation from u64 to unsigned long while the user-interface
still refers to it as u64.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch releases the lock on the state before calling
x->type->input. It also adds the lock to the spots where they're
currently needed.
Most of those places (all except mip6) are expected to disappear with
async crypto.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to the moving out of the replay processing on the output, this
patch moves the integrity stat collectin from x->type->input into
xfrm_input.
This would eventually allow transforms such as AH/ESP to be lockless.
The error value EBADMSG (currently unused in the crypto layer) is used
to indicate a failed integrity check. In future this error can be
directly returned by the crypto layer once we switch to aead
algorithms.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As it is xfrm_input first collects a list of xfrm states on the stack
before storing them in the packet's security path just before it
returns. For async crypto, this construction presents an obstacle
since we may need to leave the loop after each transform.
In fact, it's much easier to just skip the stack completely and always
store to the security path. This is proven by the fact that this
patch actually shrinks the code.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of the work on asynchronous cryptographic operations, we need
to be able to resume from the spot where they occur. As such, it
helps if we isolate them to one spot.
This patch moves most of the remaining family-specific processing into
the common input code.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for async resumptions on output. To do so,
the transform would return -EINPROGRESS and subsequently invoke the
function xfrm_output_resume to resume processing.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of the work on asynchrnous cryptographic operations, we need
to be able to resume from the spot where they occur. As such, it
helps if we isolate them to one spot.
This patch moves most of the remaining family-specific processing into
the common output code.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
With inter-family transforms the inner mode differs from the outer
mode. Attempting to handle both sides from the same function means
that it needs to handle both IPv4 and IPv6 which creates duplication
and confusion.
This patch separates the two parts on the input path so that each
function deals with one family only.
In particular, the functions xfrm4_extract_inut/xfrm6_extract_inut
moves the pertinent fields from the IPv4/IPv6 IP headers into a
neutral format stored in skb->cb. This is then used by the inner mode
input functions to modify the inner IP header. In this way the input
function no longer has to know about the outer address family.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
RO mode is the only one that requires a locked output function. So
it's easier to move the lock into that function rather than requiring
everyone else to run under the lock.
In particular, this allows us to move the size check into the output
function without causing a potential dead-lock should the ICMP error
somehow hit the same SA on transmission.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Half of the code in xfrm4_bundle_create and xfrm6_bundle_create are
common. This patch extracts that logic and puts it into
xfrm_bundle_create. The rest of it are then accessed through afinfo.
As a result this fixes the problem with inter-family transforms where
we treat every xfrm dst in the bundle as if it belongs to the top
family.
This patch also fixes a long-standing error-path bug where we may free
the xfrm states twice.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the flow construction from the callers of
xfrm_dst_lookup into that function. It also changes xfrm_dst_lookup
so that it takes an xfrm state as its argument instead of explicit
addresses.
This removes any address-specific logic from the callers of
xfrm_dst_lookup which is needed to correctly support inter-family
transforms.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we use x->props.header_len when resizing on output.
However, if we're resizing at all we might as well go the whole hog
and do it for the whole dst.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many-many code in the kernel initialized the timer->function
and timer->data together with calling init_timer(timer). There
is already a helper for this. Use it for networking code.
The patch is HUGE, but makes the code 130 lines shorter
(98 insertions(+), 228 deletions(-)).
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alg_key_len is the length in bits of the key, not in bytes.
Best way to fix this is to move alg_len() function from net/xfrm/xfrm_user.c
to include/net/xfrm.h, and to use it in xfrm_algo_clone()
alg_len() is renamed to xfrm_alg_len() because of its global exposition.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
In include/net/xfrm.h we find :
#ifdef CONFIG_XFRM_MIGRATE
extern int km_migrate(struct xfrm_selector *sel, u8 dir, u8 type,
struct xfrm_migrate *m, int num_bundles);
...
#endif
We can also guard the function body itself in net/xfrm/xfrm_state.c
with same condition.
(Problem spoted by sparse checker)
make C=2 net/xfrm/xfrm_state.o
...
net/xfrm/xfrm_state.c:1765:5: warning: symbol 'km_migrate' was not declared. Should it be static?
...
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In several places the arguments to the xfrm_audit_start() function are
in the wrong order resulting in incorrect user information being
reported. This patch corrects this by pacing the arguments in the
correct order.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the IPsec protocol SPI values are written to the audit log in
network byte order which is different from almost all other values which
are recorded in host byte order. This patch corrects this inconsistency
by writing the SPI values to the audit record in host byte order.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we get an error during the actual policy lookup we don't free the
original dst while the caller expects us to always free the original
dst in case of error.
This patch fixes that.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Morton reported that __xfrm_lookup generates this warning:
net/xfrm/xfrm_policy.c: In function '__xfrm_lookup':
net/xfrm/xfrm_policy.c:1449: warning: 'dst' may be used uninitialized in this function
This is because if policy->action is of an unexpected value then dst will
not be initialised. Of course, in practice this should never happen since
the input layer xfrm_user/af_key will filter out all illegal values. But
the compiler doesn't know that of course.
So this patch fixes this by taking the conservative approach and treat all
unknown actions the same as a blocking action.
Thanks to Andrew for finding this and providing an initial fix.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The xfrm_timer calls __xfrm_state_delete, which drops the final reference
manually without triggering destruction of the state. Change it to use
xfrm_state_put to add the state to the gc list when we're dropping the
last reference. The timer function may still continue to use the state
safely since the final destruction does a del_timer_sync().
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The change 050f009e16
[IPSEC]: Lock state when copying non-atomic fields to user-space
caused a regression.
Ingo Molnar reports that it causes a potential dead-lock found by the
lock validator as it tries to take x->lock within xfrm_state_lock while
numerous other sites take the locks in opposite order.
For 2.6.24, the best fix is to simply remove the added locks as that puts
us back in the same state as we've been in for years. For later kernels
a proper fix would be to reverse the locking order for every xfrm state
user such that if x->lock is taken together with xfrm_state_lock then
it is to be taken within it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Not architecture specific code should not #include <asm/scatterlist.h>.
This patch therefore either replaces them with
#include <linux/scatterlist.h> or simply removes them if they were
unused.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Most drivers need to set length and offset as well, so may as well fold
those three lines into one.
Add sg_assign_page() for those two locations that only needed to set
the page, where the offset/length is set outside of the function context.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
net/xfrm/xfrm_algo.c: In function 'skb_icv_walk':
net/xfrm/xfrm_algo.c:555: error: implicit declaration of function
'sg_set_page'
make[2]: *** [net/xfrm/xfrm_algo.o] Error 1
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch adds a new field to xfrm states called inner_mode. The existing
mode object is renamed to outer_mode.
This is the first part of an attempt to fix inter-family transforms. As it
is we always use the outer family when determining which mode to use. As a
result we may end up shoving IPv4 packets into netfilter6 and vice versa.
What we really want is to use the inner family for the first part of outbound
processing and the outer family for the second part. For inbound processing
we'd use the opposite pairing.
I've also added a check to prevent silly combinations such as transport mode
with inter-family transforms.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is convenient to have a pointer from xfrm_state to address-specific
functions such as the output function for a family. Currently the
address-specific policy code calls out to the xfrm state code to get
those pointers when we could get it in an easier way via the state
itself.
This patch adds an xfrm_state_afinfo to xfrm_mode (since they're
address-specific) and changes the policy code to use it. I've also
added an owner field to do reference counting on the module providing
the afinfo even though it isn't strictly necessary today since IPv6
can't be unloaded yet.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently BEET mode does not reinject the packet back into the stack
like tunnel mode does. Since BEET should behave just like tunnel mode
this is incorrect.
This patch fixes this by introducing a flags field to xfrm_mode that
tells the IPsec code whether it should terminate and reinject the packet
back into the stack.
It then sets the flag for BEET and tunnel mode.
I've also added a number of missing BEET checks elsewhere where we check
whether a given mode is a tunnel or not.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The type and mode maps are only used by SAs, not policies. So it makes
sense to move them from xfrm_policy.c into xfrm_state.c. This also allows
us to mark xfrm_get_type/xfrm_put_type/xfrm_get_mode/xfrm_put_mode as
static.
The only other change I've made in the move is to get rid of the casts
on the request_module call for types. They're unnecessary because C
will promote them to ints anyway.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently xfrm_parse_spi requires there to be 16 bytes for AH and ESP.
In contrived cases there may not actually be 16 bytes there since the
respective header sizes are less than that (8 and 12 currently).
This patch changes the test to use the actual header length instead of 16.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch make processing netlink user -> kernel messages synchronious.
This change was inspired by the talk with Alexey Kuznetsov about current
netlink messages processing. He says that he was badly wrong when introduced
asynchronious user -> kernel communication.
The call netlink_unicast is the only path to send message to the kernel
netlink socket. But, unfortunately, it is also used to send data to the
user.
Before this change the user message has been attached to the socket queue
and sk->sk_data_ready was called. The process has been blocked until all
pending messages were processed. The bad thing is that this processing
may occur in the arbitrary process context.
This patch changes nlk->data_ready callback to get 1 skb and force packet
processing right in the netlink_unicast.
Kernel -> user path in netlink_unicast remains untouched.
EINTR processing for in netlink_run_queue was changed. It forces rtnl_lock
drop, but the process remains in the cycle until the message will be fully
processed. So, there is no need to use this kludges now.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch releases the lock on the state before calling x->type->output.
It also adds the lock to the spots where they're currently needed.
Most of those places (all except mip6) are expected to disappear with
async crypto.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds locking so that when we're copying non-atomic fields such as
life-time or coaddr to user-space we don't get a partial result.
For af_key I've changed every instance of pfkey_xfrm_state2msg apart from
expiration notification to include the keys and life-times. This is in-line
with XFRM behaviour.
The actual cases affected are:
* pfkey_getspi: No change as we don't have any keys to copy.
* key_notify_sa:
+ ADD/UPD: This wouldn't work otherwise.
+ DEL: It can't hurt.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here's a good example of code duplication leading to code rot. The
notification patch did its own netlink message creation for xfrm states.
It duplicated code that was already in dump_one_state. Guess what, the
next time (and the time after) when someone updated dump_one_state the
notification path got zilch.
This patch moves that code from dump_one_state to copy_to_user_state_extra
and uses it in xfrm_notify_sa too. Unfortunately whoever updates this
still needs to update xfrm_sa_len since the notification path wants to
know the exact size for allocation.
At least I've added a comment saying so and if someone still forgest, we'll
have a WARN_ON telling us so.
I also changed the security size calculation to use xfrm_user_sec_ctx since
that's what we actually put into the skb. However it makes no practical
difference since it has the same size as xfrm_sec_ctx.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves some common code that conceptually belongs to the xfrm core
from af_key/xfrm_user into xfrm_alloc_spi.
In particular, the spin lock on the state is now taken inside xfrm_alloc_spi.
Previously it also protected the construction of the response PF_KEY/XFRM
messages to user-space. This is inconsistent as other identical constructions
are not protected by the state lock. This is bad because they in fact should
be protected but only in certain spots (so as not to hold the lock for too
long which may cause packet drops).
The SPI byte order conversion has also been moved.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no point in waking people up when creating/updating larval states
because they'll just go back to sleep again as larval states by definition
cannot be found by xfrm_state_find.
We should only wake them up when the larvals mature or die.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current the x->mode->output functions store the IPv6 nh pointer in the
skb network header. This is inconvenient because the network header then
has to be fixed up before the packet can leave the IPsec stack. The mac
header field is unused on output so we can use that to store this instead.
This patch does that and removes the network header fix-up in xfrm_output.
It also uses ipv6_hdr where appropriate in the x->type->output functions.
There is also a minor clean-up in esp4 to make it use the same code as
esp6 to help any subsequent effort to merge the two.
Lastly it kills two redundant skb_set_* statements in BEET that were
simply copied over from transport mode.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Constructs of the form
xfrm_state_hold(x);
foo(x);
xfrm_state_put(x);
tend to be broken because foo is either synchronous where this is totally
unnecessary or if foo is asynchronous then the reference count is in the
wrong spot.
In the case of xfrm_secpath_reject, the function is synchronous and therefore
we should just kill the reference count.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lastused update check in xfrm_output can be done just as well in
the mode output function which is specific to RO.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the only callers of xfrm_replay_notify are in xfrm, we can remove
the export.
This patch also removes xfrm_aevent_doreplay since it's now called in just
one spot.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The replay counter is one of only two remaining things in the output code
that requires a lock on the xfrm state (the other being the crypto). This
patch moves it into the generic xfrm_output so we can remove the lock from
the transforms themselves.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions xfrm_state_check and xfrm_state_check_space are only used by
the output code in xfrm_output.c so we can move them over.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the code in xfrm4_output_one and xfrm6_output_one are identical so
this patch moves them into a common xfrm_output function which will live
in net/xfrm.
In fact this would seem to fix a bug as on IPv4 we never reset the network
header after a transform which may upset netfilter later on.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes loopback_dev per network namespace. Adding
code to create a different loopback device for each network
namespace and adding the code to free a loopback device
when a network namespace exits.
This patch modifies all users the loopback_dev so they
access it as init_net.loopback_dev, keeping all of the
code compiling and working. A later pass will be needed to
update the users to use something other than the initial network
namespace.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces all occurences to the static variable
loopback_dev to a pointer loopback_dev. That provides the
mindless, trivial, uninteressting change part for the dynamic
allocation for the loopback.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Acked-By: Kirill Korotaev <dev@sw.ru>
Acked-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
I was looking at Patrick's fix to inet_diag and it occured
to me that we're using a pointer argument to return values
unnecessarily in netlink_run_queue. Changing it to return
the value will allow the compiler to generate better code
since the value won't have to be memory-backed.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each netlink socket will live in exactly one network namespace,
this includes the controlling kernel sockets.
This patch updates all of the existing netlink protocols
to only support the initial network namespace. Request
by clients in other namespaces will get -ECONREFUSED.
As they would if the kernel did not have the support for
that netlink protocol compiled in.
As each netlink protocol is updated to be multiple network
namespace safe it can register multiple kernel sockets
to acquire a presence in the rest of the network namespaces.
The implementation in af_netlink is a simple filter implementation
at hash table insertion and hash table look up time.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every user of the network device notifiers is either a protocol
stack or a pseudo device. If a protocol stack that does not have
support for multiple network namespaces receives an event for a
device that is not in the initial network namespace it quite possibly
can get confused and do the wrong thing.
To avoid problems until all of the protocol stacks are converted
this patch modifies all netdev event handlers to ignore events on
devices that are not in the initial network namespace.
As the rest of the code is made network namespace aware these
checks can be removed.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies the current ipsec audit layer
by breaking it up into purpose driven audit calls.
So far, the only audit calls made are when add/delete
an SA/policy. It had been discussed to give each
key manager it's own calls to do this, but I found
there to be much redundnacy since they did the exact
same things, except for how they got auid and sid, so I
combined them. The below audit calls can be made by any
key manager. Hopefully, this is ok.
Signed-off-by: Joy Latten <latten@austin.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions are only used once and are a lot easier to understand if
inlined directly into the function.
Fixes by Masahide NAKAMURA.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
nlmsg_parse() puts attributes at array[type] so the indexing
method can be simpilfied by removing the obscuring "- 1".
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds a policy defining the minimal payload lengths for all the attributes
allowing for most attribute validation checks to be removed from in
the middle of the code path. Makes updates more consistent as many format
errors are recognised earlier, before any changes have been attempted.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Uses nlmsg_parse() to parse the attributes. This actually changes
behaviour as unknown attributes (type > MAXTYPE) no longer cause
an error. Instead unknown attributes will be ignored henceforth
to keep older kernels compatible with more recent userspace tools.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moves all complex message size calculation into own inlined helper
functions and makes use of the type-safe netlink interface.
Using nlmsg_new() simplifies the calculation itself as it takes care
of the netlink header length by itself.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moves all of the SUB_POLICY ifdefs related to the attribute size
calculation into a function.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds alg_len() to calculate the properly padded length of an
algorithm attribute to simplify the code.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also makes use of copy_sec_ctx() in another place and removes
duplicated code.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up duplicate includes in
net/xfrm/
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The security_secid_to_secctx() function returns memory that must be freed
by a call to security_release_secctx() which was not always happening. This
patch fixes two of these problems (all that I could find in the kernel source
at present).
Signed-off-by: Paul Moore <paul.moore@hp.com>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: James Morris <jmorris@namei.org>
This patch modifies the xfrm state selection logic to use the inner
addresses where the outer have been (incorrectly) used. This is
required for beet mode in general and interfamily setups in both
tunnel and beet mode.
Signed-off-by: Joakim Koskela <jookos@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Diego Beltrami <diego.beltrami@gmail.com>
Signed-off-by: Miika Komu <miika@iki.fi>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to the issue we had with template families which
specified the inner families of policies, we need to set
the inner families of states as the main xfrm user Openswan
leaves it as zero.
af_key is unaffected because the inner family is set by it
and not the KM.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Slab destructors were no longer supported after Christoph's
c59def9f22 change. They've been
BUGs for both slab and slub, and slob never supported them
either.
This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
XFRM expects xfrm_dst->u.next to be same pointer as dst->next, which
was broken by the dst_entry reordering in commit 1e19e02c~, causing
an oops in xfrm_bundle_ok when walking the bundle upwards.
Kill xfrm_dst->u.next and change the only user to use dst->next instead.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows other in-kernel functions to do SAD lookups.
The only known user at the moment is pktgen.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
My IPsec MTU optimization patch introduced a regression in MTU calculation
for non-ESP SAs, the SA's header_len needs to be subtracted from the MTU if
the transform doesn't provide a ->get_mtu() function.
Reported-and-tested-by: Marco Berizzi <pupilla@hotmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we check for permission before deleting entries from SAD and
SPD, (see security_xfrm_policy_delete() security_xfrm_state_delete())
However we are not checking for authorization when flushing the SPD and
the SAD completely. It was perhaps missed in the original security hooks
patch.
This patch adds a security check when flushing entries from the SAD and
SPD. It runs the entire database and checks each entry for a denial.
If the process attempting the flush is unable to remove all of the
entries a denial is logged the the flush function returns an error
without removing anything.
This is particularly useful when a process may need to create or delete
its own xfrm entries used for things like labeled networking but that
same process should not be able to delete other entries or flush the
entire database.
Signed-off-by: Joy Latten<latten@austin.ibm.com>
Signed-off-by: Eric Paris <eparis@parisplace.org>
Signed-off-by: James Morris <jmorris@namei.org>
The current IPSEC rule resolution behavior we have does not work for a
lot of people, even though technically it's an improvement from the
-EAGAIN buisness we had before.
Right now we'll block until the key manager resolves the route. That
works for simple cases, but many folks would rather packets get
silently dropped until the key manager resolves the IPSEC rules.
We can't tell these folks to "set the socket non-blocking" because
they don't have control over the non-block setting of things like the
sockets used to resolve DNS deep inside of the resolver libraries in
libc.
With that in mind I coded up the patch below with some help from
Herbert Xu which provides packet-drop behavior during larval state
resolution, controllable via sysctl and off by default.
This lays the framework to either:
1) Make this default at some point or...
2) Move this logic into xfrm{4,6}_policy.c and implement the
ARP-like resolution queue we've all been dreaming of.
The idea would be to queue packets to the policy, then
once the larval state is resolved by the key manager we
re-resolve the route and push the packets out. The
packets would timeout if the rule didn't get resolved
in a certain amount of time.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds some casts to shut up the warnings introduced by my
last patch that added a common interator function for xfrm algorightms.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a natural extension of the changeset
[XFRM]: Probe selected algorithm only.
which only removed the probe call for xfrm_user. This patch does exactly
the same thing for af_key. In other words, we load the algorithm requested
by the user rather than everything when adding xfrm states in af_key.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multi-page allocations are always likely to fail. Since such failures
are expected and non-critical in xfrm_hash_alloc, we shouldn't warn about
them.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function xfrm_policy_byid takes a dir argument but finds the policy
using the index instead. We only use the dir argument to update the
policy count for that direction. Since the user can supply any value
for dir, this can corrupt our policy count.
I know this is the problem because a few days ago I was deleting
policies by hand using indicies and accidentally typed in the wrong
direction. It still deleted the policy and at the time I thought
that was cool. In retrospect it isn't such a good idea :)
I decided against letting it delete the policy anyway just in case
we ever remove the connection between indicies and direction.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aggregate the SPD info TLVs.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aggregate the SAD info TLVs.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
On MIPv6 usage, XFRM sub policy is enabled.
When main (IPsec) and sub (MIPv6) policy selectors have the same
address set but different upper layer information (i.e. protocol
number and its ports or type/code), multiple bundle should be created.
However, currently we have issue to use the same bundle created for
the first time with all flows covered by the case.
It is useful for the bundle to have the upper layer information
to be restructured correctly if it does not match with the flow.
1. Bundle was created by two policies
Selector from another policy is added to xfrm_dst.
If the flow does not match the selector, it goes to slow path to
restructure new bundle by single policy.
2. Bundle was created by one policy
Flow cache is added to xfrm_dst as originated one. If the flow does
not match the cache, it goes to slow path to try searching another
policy.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch you can use iproute2 in user space to efficiently see
how many policies exist in different directions.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts eefa390628
The simplification made in that change works with the assumption that
the 'offset' parameter to these functions is always positive or zero,
which is not true. It can be and often is negative in order to access
SKB header values in front of skb->data.
Signed-off-by: David S. Miller <davem@davemloft.net>
This brings the SAD info in sync with net-2.6.22/net-2.6
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
I noticed recently that, in skb_checksum(), "offset" and "start" are
essentially the same thing and have the same value throughout the
function, despite being computed differently. Using a single variable
allows some cleanups and makes the skb_checksum() function smaller,
more readable, and presumably marginally faster.
We appear to have many other "sk_buff walker" functions built on the
exact same model, so the cleanup applies to them, too. Here is a list
of the functions I found to be affected:
net/appletalk/ddp.c:atalk_sum_skb()
net/core/datagram.c:skb_copy_datagram_iovec()
net/core/datagram.c:skb_copy_and_csum_datagram()
net/core/skbuff.c:skb_copy_bits()
net/core/skbuff.c:skb_store_bits()
net/core/skbuff.c:skb_checksum()
net/core/skbuff.c:skb_copy_and_csum_bit()
net/core/user_dma.c:dma_skb_copy_datagram_iovec()
net/xfrm/xfrm_algo.c:skb_icv_walk()
net/xfrm/xfrm_algo.c:skb_to_sgvec()
OTOH, I admit I'm a bit surprised, the cleanup is rather obvious so I'm
really wondering if I am missing something. Can anyone please comment
on this?
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
On a system with a lot of SAs, counting SAD entries chews useful
CPU time since you need to dump the whole SAD to user space;
i.e something like ip xfrm state ls | grep -i src | wc -l
I have seen taking literally minutes on a 40K SAs when the system
is swapping.
With this patch, some of the SAD info (that was already being tracked)
is exposed to user space. i.e you do:
ip xfrm state count
And you get the count; you can also pass -s to the command line and
get the hash info.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spring cleaning time...
There seems to be a lot of places in the network code that have
extra bogus semicolons after conditionals. Most commonly is a
bogus semicolon after: switch() { }
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch cb_lock to mutex and allow netlink kernel users to override it
with a subsystem specific mutex for consistent locking in dump callbacks.
All netlink_dump_start users have been audited not to rely on any
side-effects of the previously used spinlock.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the probing based MTU estimation, which usually takes 2-3 iterations
to find a fitting value and may underestimate the MTU, by an exact calculation.
Also fix underestimation of the XFRM trailer_len, which causes unnecessary
reallocations.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move generic skbuff stuff from XFRM code to generic code so that
AF_RXRPC can use it too.
The kdoc comments I've attached to the functions needs to be checked
by whoever wrote them as I had to make some guesses about the workings
of these functions.
Signed-off-By: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all users of netlink_dump_start() use netlink_run_queue()
to process the receive queue, it is possible to return -EINTR from
netlink_dump_start() directly, therefore simplying the callers.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error pointer argument in netlink message handlers is used
to signal the special case where processing has to be interrupted
because a dump was started but no error happened. Instead it is
simpler and more clear to return -EINTR and have netlink_run_queue()
deal with getting the queue right.
nfnetlink passed on this error pointer to its subsystem handlers
but only uses it to signal the start of a netlink dump. Therefore
it can be removed there as well.
This patch also cleans up the error handling in the affected
message handlers to be consistent since it had to be touched anyway.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes netlink_rcv_skb() to skip netlink controll messages and don't
pass them on to the message handler.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
netlink_rcv_skb() is changed to skip messages which don't have the
NLM_F_REQUEST bit to avoid every netlink family having to perform this
check on their own.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
So that it is also an offset from skb->head, reduces its size from 8 to 4 bytes
on 64bit architectures, allowing us to combine the 4 bytes hole left by the
layer headers conversion, reducing struct sk_buff size to 256 bytes, i.e. 4
64byte cachelines, and since the sk_buff slab cache is SLAB_HWCACHE_ALIGN...
:-)
Many calculations that previously required that skb->{transport,network,
mac}_header be first converted to a pointer now can be done directly, being
meaningful as offsets or pointers.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the places where we need a pointer to the transport header, it is
still legal to touch skb->h.raw directly if just adding to,
subtracting from or setting it to another layer header.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Where appropriate, convert references to xtime.tv_sec to the
get_seconds() helper function.
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending a security context of 50+ characters in an ACQUIRE
message, following kernel panic occurred.
kernel BUG in xfrm_send_acquire at net/xfrm/xfrm_user.c:1781!
cpu 0x3: Vector: 700 (Program Check) at [c0000000421bb2e0]
pc: c00000000033b074: .xfrm_send_acquire+0x240/0x2c8
lr: c00000000033b014: .xfrm_send_acquire+0x1e0/0x2c8
sp: c0000000421bb560
msr: 8000000000029032
current = 0xc00000000fce8f00
paca = 0xc000000000464b00
pid = 2303, comm = ping
kernel BUG in xfrm_send_acquire at net/xfrm/xfrm_user.c:1781!
enter ? for help
3:mon> t
[c0000000421bb650] c00000000033538c .km_query+0x6c/0xec
[c0000000421bb6f0] c000000000337374 .xfrm_state_find+0x7f4/0xb88
[c0000000421bb7f0] c000000000332350 .xfrm_tmpl_resolve+0xc4/0x21c
[c0000000421bb8d0] c0000000003326e8 .xfrm_lookup+0x1a0/0x5b0
[c0000000421bba00] c0000000002e6ea0 .ip_route_output_flow+0x88/0xb4
[c0000000421bbaa0] c0000000003106d8 .ip4_datagram_connect+0x218/0x374
[c0000000421bbbd0] c00000000031bc00 .inet_dgram_connect+0xac/0xd4
[c0000000421bbc60] c0000000002b11ac .sys_connect+0xd8/0x120
[c0000000421bbd90] c0000000002d38d0 .compat_sys_socketcall+0xdc/0x214
[c0000000421bbe30] c00000000000869c syscall_exit+0x0/0x40
--- Exception: c00 (System Call) at 0000000007f0ca9c
SP (fc0ef8f0) is in userspace
We are using size of security context from xfrm_policy to determine
how much space to alloc skb and then putting security context from
xfrm_state into skb. Should have been using size of security context
from xfrm_state to alloc skb. Following fix does that
Signed-off-by: Joy Latten <latten@austin.ibm.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until this point we've accepted replay window settings greater than
32 but our bit mask can only accomodate 32 packets. Thus any packet
with a sequence number within the window but outside the bit mask would
be accepted.
This patch causes those packets to be rejected instead.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turning up the warnings on gcc makes it emit warnings
about the placement of 'inline' in function declarations.
Here's everything that was under net/
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a space between printing of the src and dst ipv6 addresses.
Otherwise, audit or other test tools may fail to process the audit
record properly because they cannot find the dst address.
Signed-off-by: Joy Latten <latten@austin.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I noticed that in xfrm_state_add we look for the larval SA in a few
places without checking for protocol match. So when using both
AH and ESP, whichever one gets added first, deletes the larval SA.
It seems AH always gets added first and ESP is always the larval
SA's protocol since the xfrm->tmpl has it first. Thus causing the
additional km_query()
Adding the check eliminates accidental double SA creation.
Signed-off-by: Joy Latten <latten@austin.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inside pfkey_delete and xfrm_del_sa the audit hooks were not called if
there was any permission/security failures in attempting to do the del
operation (such as permission denied from security_xfrm_state_delete).
This patch moves the audit hook to the exit path such that all failures
(and successes) will actually get audited.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Venkat Yekkirala <vyekkirala@trustedcs.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The security hooks to check permissions to remove an xfrm_policy were
actually done after the policy was removed. Since the unlinking and
deletion are done in xfrm_policy_by* functions this moves the hooks
inside those 2 functions. There we have all the information needed to
do the security check and it can be done before the deletion. Since
auditing requires the result of that security check err has to be passed
back and forth from the xfrm_policy_by* functions.
This patch also fixes a bug where a deletion that failed the security
check could cause improper accounting on the xfrm_policy
(xfrm_get_policy didn't have a put on the exit path for the hold taken
by xfrm_policy_by*)
It also fixes the return code when no policy is found in
xfrm_add_pol_expire. In old code (at least back in the 2.6.18 days) err
wasn't used before the return when no policy is found and so the
initialization would cause err to be ENOENT. But since err has since
been used above when we don't get a policy back from the xfrm_policy_by*
function we would always return 0 instead of the intended ENOENT. Also
fixed some white space damage in the same area.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Venkat Yekkirala <vyekkirala@trustedcs.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noted by Kent Yoder, this function will always return an
error. Make sure it returns zero on success.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the address family to refer encap_family
when comparing with a kernel generated xfrm_state
Signed-off-by: Kazunori MIYAZAWA <miyazawa@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure that this function is called correctly, and
add BUG() checking to ensure the arguments are sane.
Based upon a patch by Joy Latten.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add CONFIG_NET_KEY_MIGRATE option which makes it possible for user
application to send or receive MIGRATE message to/from PF_KEY socket.
Signed-off-by: Shinta Sugimoto <shinta.sugimoto@ericsson.com>
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add CONFIG_XFRM_MIGRATE option which makes it possible for for user
application to send or receive MIGRATE message to/from netlink socket.
Signed-off-by: Shinta Sugimoto <shinta.sugimoto@ericsson.com>
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add user interface for handling XFRM_MSG_MIGRATE. The message is issued
by user application. When kernel receives the message, procedure of
updating XFRM databases will take place.
Signed-off-by: Shinta Sugimoto <shinta.sugimoto@ericsson.com>
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the XFRM framework so that endpoint address(es) in the XFRM
databases could be dynamically updated according to a request (MIGRATE
message) from user application. Target XFRM policy is first identified
by the selector in the MIGRATE message. Next, the endpoint addresses
of the matching templates and XFRM states are updated according to
the MIGRATE message.
Signed-off-by: Shinta Sugimoto <shinta.sugimoto@ericsson.com>
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch exports xfrm_state_afinfo.
Signed-off-by: Miika Komu <miika@iki.fi>
Signed-off-by: Diego Beltrami <Diego.Beltrami@hiit.fi>
Signed-off-by: Kazunori Miyazawa <miyazawa@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the entry of Camellia cipher algorithm to ealg_list[].
Signed-off-by: Noriaki TAKAMIYA <takamiya@po.ntts.co.jp>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The recent hashing introduced an off-by-one bug in policy list insertion.
Instead of adding after the last entry with a lesser or equal priority,
we're adding after the successor of that entry.
This patch fixes this and also adds a warning if we detect a duplicate
entry in the policy list. This should never happen due to this if clause.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
All ->doit handlers want a struct rtattr **, so pass down the right
type.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Installing an IPsec SA using old algorithm names (.compat) does not work
if the algorithm is not already loaded. When not using the PF_KEY
interface, algorithms are not preloaded in xfrm_probe_algs() and
installing a IPsec SA fails.
Signed-off-by: Martin Willi <martin@strongswan.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all uses of kmem_cache_t with struct kmem_cache.
The patch was generated using the following script:
#!/bin/sh
#
# Replace one string by another in all the kernel sources.
#
set -e
for file in `find * -name "*.c" -o -name "*.h"|xargs grep -l $1`; do
quilt add $file
sed -e "1,\$s/$1/$2/g" $file >/tmp/$$
mv /tmp/$$ $file
quilt refresh
done
The script was run like this
sh replace kmem_cache_t "struct kmem_cache"
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_ATOMIC is an alias of GFP_ATOMIC
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Disables auditing in ipsec when CONFIG_AUDITSYSCALL is
disabled in the kernel.
Also includes a bug fix for xfrm_state.c as a result of
original ipsec audit patch.
Signed-off-by: Joy Latten <latten@austin.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
An audit message occurs when an ipsec SA
or ipsec policy is created/deleted.
Signed-off-by: Joy Latten <latten@austin.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change optimizes the dumping of Security policies.
1) Before this change ..
speedopolis:~# time ./ip xf pol
real 0m22.274s
user 0m0.000s
sys 0m22.269s
2) Turn off sub-policies
speedopolis:~# ./ip xf pol
real 0m13.496s
user 0m0.000s
sys 0m13.493s
i suppose the above is to be expected
3) With this change ..
speedopolis:~# time ./ip x policy
real 0m7.901s
user 0m0.008s
sys 0m7.896s
Conflicts:
drivers/ata/libata-scsi.c
include/linux/libata.h
Futher merge of Linus's head and compilation fixups.
Signed-Off-By: David Howells <dhowells@redhat.com>
Conflicts:
drivers/infiniband/core/iwcm.c
drivers/net/chelsio/cxgb2.c
drivers/net/wireless/bcm43xx/bcm43xx_main.c
drivers/net/wireless/prism54/islpci_eth.c
drivers/usb/core/hub.h
drivers/usb/input/hid-core.c
net/core/netpoll.c
Fix up merge failures with Linus's head and fix new compilation failures.
Signed-Off-By: David Howells <dhowells@redhat.com>
Since we never checked the ->family value of templates
before, many applications simply leave it at zero.
Detect this and fix it up to be the pol->family value.
Also, do not clobber xp->family while reading in templates,
that is not necessary.
Signed-off-by: David S. Miller <davem@davemloft.net>
aevents can not uniquely identify an SA. We break the ABI with this
patch, but consensus is that since it is not yet utilized by any
(known) application then it is fine (better do it now than later).
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Miika Komu <miika@iki.fi>
Signed-off-by: Diego Beltrami <Diego.Beltrami@hiit.fi>
Signed-off-by: Kazunori Miyazawa <miyazawa@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Miika Komu <miika@iki.fi>
Signed-off-by: Diego Beltrami <Diego.Beltrami@hiit.fi>
Signed-off-by: Kazunori Miyazawa <miyazawa@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Might as well make flush notifier prettier when subpolicy used
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
The destination PID is passed directly to netlink_unicast()
respectively netlink_multicast().
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make copy_to_user_policy_type take a type instead a policy and
fix its users to pass the type
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the selection of an SA for an outgoing packet to be at the same
context as the originating socket/flow. This eliminates the SELinux
policy's ability to use/sendto SAs with contexts other than the socket's.
With this patch applied, the SELinux policy will require one or more of the
following for a socket to be able to communicate with/without SAs:
1. To enable a socket to communicate without using labeled-IPSec SAs:
allow socket_t unlabeled_t:association { sendto recvfrom }
2. To enable a socket to communicate with labeled-IPSec SAs:
allow socket_t self:association { sendto };
allow socket_t peer_sa_t:association { recvfrom };
Signed-off-by: Venkat Yekkirala <vyekkirala@TrustedCS.com>
Signed-off-by: James Morris <jmorris@namei.org>
When application uses XFRM_MSG_GETSA to get state entry through
netlink socket and kernel has no matching one, the application expects
reply message with error status by kernel.
Kernel doesn't send the message back in the case of Mobile IPv6 route
optimization protocols (i.e. routing header or destination options
header). This is caused by incorrect return code "0" from
net/xfrm/xfrm_user.c(xfrm_user_state_lookup) and it makes kernel skip
to acknowledge at net/netlink/af_netlink.c(netlink_rcv_skb).
This patch fix to reply ESRCH to application.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: TAKAMIYA Noriaki <takamiya@po.ntts.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
I actually dont have a test case for these; i just found them by
inspection. Refer to patch "[XFRM]: Sub-policies broke policy events"
for more info
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Acked-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
XFRM policy events are broken when sub-policy feature is turned on.
A simple test to verify this:
run ip xfrm mon on one window and add then delete a policy on another
window ..
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Acked-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use memcpy() to move xfrm_address_t objects in and out
of netlink messages. The vast majority of xfrm_user was
doing this properly, except for copy_from_user_state()
and copy_to_user_state().
Signed-off-by: David S. Miller <davem@davemloft.net>
xfrm_state_num needs to be increased for XFRM_STATE_ACQ states created
by xfrm_state_find() to prevent the counter from going negative when
the state is destroyed.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Missing counter bump when hashing in a new ACQ
xfrm_state.
Now that we have two spots to do the hash grow
check, break it out into a helper function.
Signed-off-by: David S. Miller <davem@davemloft.net>
This treats the security errors encountered in the case of
socket policy matching, the same as how these are treated in
the case of main/sub policies, which is to return a full lookup
failure.
Signed-off-by: Venkat Yekkirala <vyekkirala@TrustedCS.com>
Signed-off-by: James Morris <jmorris@namei.org>
Currently when an IPSec policy rule doesn't specify a security
context, it is assumed to be "unlabeled" by SELinux, and so
the IPSec policy rule fails to match to a flow that it would
otherwise match to, unless one has explicitly added an SELinux
policy rule allowing the flow to "polmatch" to the "unlabeled"
IPSec policy rules. In the absence of such an explicitly added
SELinux policy rule, the IPSec policy rule fails to match and
so the packet(s) flow in clear text without the otherwise applicable
xfrm(s) applied.
The above SELinux behavior violates the SELinux security notion of
"deny by default" which should actually translate to "encrypt by
default" in the above case.
This was first reported by Evgeniy Polyakov and the way James Morris
was seeing the problem was when connecting via IPsec to a
confined service on an SELinux box (vsftpd), which did not have the
appropriate SELinux policy permissions to send packets via IPsec.
With this patch applied, SELinux "polmatching" of flows Vs. IPSec
policy rules will only come into play when there's a explicit context
specified for the IPSec policy rule (which also means there's corresponding
SELinux policy allowing appropriate domains/flows to polmatch to this context).
Secondly, when a security module is loaded (in this case, SELinux), the
security_xfrm_policy_lookup() hook can return errors other than access denied,
such as -EINVAL. We were not handling that correctly, and in fact
inverting the return logic and propagating a false "ok" back up to
xfrm_lookup(), which then allowed packets to pass as if they were not
associated with an xfrm policy.
The solution for this is to first ensure that errno values are
correctly propagated all the way back up through the various call chains
from security_xfrm_policy_lookup(), and handled correctly.
Then, flow_cache_lookup() is modified, so that if the policy resolver
fails (typically a permission denied via the security module), the flow
cache entry is killed rather than having a null policy assigned (which
indicates that the packet can pass freely). This also forces any future
lookups for the same flow to consult the security module (e.g. SELinux)
for current security policy (rather than, say, caching the error on the
flow cache entry).
This patch: Fix the selinux side of things.
This makes sure SELinux polmatching of flow contexts to IPSec policy
rules comes into play only when an explicit context is associated
with the IPSec policy rule.
Also, this no longer defaults the context of a socket policy to
the context of the socket since the "no explicit context" case
is now handled properly.
Signed-off-by: Venkat Yekkirala <vyekkirala@TrustedCS.com>
Signed-off-by: James Morris <jmorris@namei.org>
When a security module is loaded (in this case, SELinux), the
security_xfrm_policy_lookup() hook can return an access denied permission
(or other error). We were not handling that correctly, and in fact
inverting the return logic and propagating a false "ok" back up to
xfrm_lookup(), which then allowed packets to pass as if they were not
associated with an xfrm policy.
The way I was seeing the problem was when connecting via IPsec to a
confined service on an SELinux box (vsftpd), which did not have the
appropriate SELinux policy permissions to send packets via IPsec.
The first SYNACK would be blocked, because of an uncached lookup via
flow_cache_lookup(), which would fail to resolve an xfrm policy because
the SELinux policy is checked at that point via the resolver.
However, retransmitted SYNACKs would then find a cached flow entry when
calling into flow_cache_lookup() with a null xfrm policy, which is
interpreted by xfrm_lookup() as the packet not having any associated
policy and similarly to the first case, allowing it to pass without
transformation.
The solution presented here is to first ensure that errno values are
correctly propagated all the way back up through the various call chains
from security_xfrm_policy_lookup(), and handled correctly.
Then, flow_cache_lookup() is modified, so that if the policy resolver
fails (typically a permission denied via the security module), the flow
cache entry is killed rather than having a null policy assigned (which
indicates that the packet can pass freely). This also forces any future
lookups for the same flow to consult the security module (e.g. SELinux)
for current security policy (rather than, say, caching the error on the
flow cache entry).
Signed-off-by: James Morris <jmorris@namei.org>
This patch introduces the BEET mode (Bound End-to-End Tunnel) with as
specified by the ietf draft at the following link:
http://www.ietf.org/internet-drafts/draft-nikander-esp-beet-mode-06.txt
The patch provides only single family support (i.e. inner family =
outer family).
Signed-off-by: Diego Beltrami <diego.beltrami@gmail.com>
Signed-off-by: Miika Komu <miika@iki.fi>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Abhinav Pathak <abhinav.pathak@hiit.fi>
Signed-off-by: Jeff Ahrenholz <ahrenholz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we flush policies, we do a type match so we might not
actually delete all policies matching a certain direction.
So keep track of how many policies we actually kill and
subtract that number from xfrm_policy_count[dir] at the
end.
Based upon a patch by Masahide NAKAMURA.
Signed-off-by: David S. Miller <davem@davemloft.net>
Src hash is introduced for Mobile IPv6 route optimization usage.
On current kenrel code it is calculated with source address only.
It results we uses the same hash value for outbound state (when
the node has only one address for Mobile IPv6).
This patch use also destination address as peer information for
src hash to be dispersed.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
SPI=0 is used for acquired IPsec SA and MIPv6 RO state.
Such state should not be added to the SPI hash
because we do not care about it on deleting path.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
spi argument of xfrm_state_lookup() is net-endian
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hashing SAs by source address breaks templates with wildcards as tunnel
source since the source address used for hashing/lookup is still 0/0.
Move source address lookup to xfrm_tmpl_resolve_one() so we can use the
real address in the lookup.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems that during the MIPv6 respin, some code which was originally
conditionally compiled around CONFIG_XFRM_ADVANCED was accidently left
in after the config option was removed.
This patch removes an extraneous pointer (xerr_idxp) which is no
longer needed.
Signed-off-by: James Morris <jmorris@namei.org>
Acked-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if we find an exact match in the hash table,
we must inspect the inexact list to look for a match
with a better priority.
Noticed by Masahide NAKAMURA <nakam@linux-ipv6.org>.
Signed-off-by: David S. Miller <davem@davemloft.net>
This idea is from Alexey Kuznetsov.
It is common for policies to be non-prefixed. And for
that case we can optimize lookups, insert, etc. quite
a bit.
For each direction, we have a dynamically sized policy
hash table for non-prefixed policies. We also have a
hash table on policy->index.
For prefixed policies, we have a list per-direction which
we will consult on lookups when a non-prefix hashtable
lookup fails.
This still isn't as efficient as I would like it. There
are four immediate problems:
1) Lots of excessive refcounting, which can be fixed just
like xfrm_state was
2) We do 2 hash probes on insert, one to look for dups and
one to allocate a unique policy->index. Althought I wonder
how much this matters since xfrm_state inserts do up to
3 hash probes and that seems to perform fine.
3) xfrm_policy_insert() is very complex because of the priority
ordering and entry replacement logic.
4) Lots of counter bumping, in addition to policy refcounts,
in the form of xfrm_policy_count[]. This is merely used
to let code path(s) know that some IPSEC rules exist. So
this count is indexed per-direction, maybe that is overkill.
Signed-off-by: David S. Miller <davem@davemloft.net>
The source address is always non-prefixed so we should use
it to help give entropy to the bydst hash.
Signed-off-by: David S. Miller <davem@davemloft.net>
The refcounting done for timers and hash table insertions
are just wasted cycles. We can eliminate all of this
refcounting because:
1) The implicit refcount when the xfrm_state object is active
will always be held while the object is in the hash tables.
We never kfree() the xfrm_state until long after we've made
sure that it has been unhashed.
2) Timers are even easier. Once we mark that x->km.state as
anything other than XFRM_STATE_VALID (__xfrm_state_delete
sets it to XFRM_STATE_DEAD), any timer that fires will
do nothing and return without rearming the timer.
Therefore we can defer the del_timer calls until when the
object is about to be freed up during GC. We have to use
del_timer_sync() and defer it to GC because we can't do
a del_timer_sync() while holding x->lock which all callers
of __xfrm_state_delete hold.
This makes SA changes even more light-weight.
Signed-off-by: David S. Miller <davem@davemloft.net>
Just let GC and other normal mechanisms take care of getting
rid of DST cache references to deleted xfrm_state objects
instead of walking all the policy bundles.
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead, simply set all potentially aliasing existing xfrm_state
objects to have the current generation counter value.
This will make routes get relooked up the next time an existing
route mentioning these aliased xfrm_state objects gets used,
via xfrm_dst_check().
Signed-off-by: David S. Miller <davem@davemloft.net>
Each xfrm_state inserted gets a new generation counter
value. When a bundle is created, the xfrm_dst objects
get the current generation counter of the xfrm_state
they will attach to at dst->xfrm.
xfrm_bundle_ok() will return false if it sees an
xfrm_dst with a generation count different from the
generation count of the xfrm_state that dst points to.
This provides a facility by which to passively and
cheaply invalidate cached IPSEC routes during SA
database changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The grow algorithm is simple, we grow if:
1) we see a hash chain collision at insert, and
2) we haven't hit the hash size limit (currently 1*1024*1024 slots), and
3) the number of xfrm_state objects is > the current hash mask
All of this needs some tweaking.
Remove __initdata from "hashdist" so we can use it safely at run time.
Signed-off-by: David S. Miller <davem@davemloft.net>
Sub policy can be used through netlink socket.
PF_KEY uses main only and it is TODO to support sub.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under two transformation policies it is required to merge them.
This is a platform to sort state for outbound and templates
for inbound respectively.
It will be used when Mobile IPv6 and IPsec are used at the same time.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sub policy is introduced. Main and sub policy are applied the same flow.
(Policy that current kernel uses is named as main.)
It is required another transformation policy management to keep IPsec
and Mobile IPv6 lives separate.
Policy which lives shorter time in kernel should be a sub i.e. normally
main is for IPsec and sub is for Mobile IPv6.
(Such usage as two IPsec policies on different database can be used, too.)
Limitation or TODOs:
- Sub policy is not supported for per socket one (it is always inserted as main).
- Current kernel makes cached outbound with flowi to skip searching database.
However this patch makes it disabled only when "two policies are used and
the first matched one is bypass case" because neither flowi nor bundle
information knows about transformation template size.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Add Kconfig to support sub policy.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
XFRM_MSG_REPORT is a message as notification of state protocol and
selector from kernel to user-space.
Mobile IPv6 will use it when inbound reject is occurred at route
optimization to make user-space know a binding error requirement.
Based on MIPL2 kernel patch.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For Mobile IPv6 usage, it is required to trace which secpath state is
reject factor in order to notify it to user space (to know the address
which cannot be used route optimized communication).
Based on MIPL2 kernel patch.
This patch was also written by: Henrik Petander <petander@tcs.hut.fi>
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Mobile IPv6 route optimization protocols to netlink interface.
Route optimization states carry care-of address.
Based on MIPL2 kernel patch.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Transformation user interface is not only for IPsec.
Based on MIPL2 kernel patch.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For outbound transformation, bundle is checked whether it is
suitable for current flow to be reused or not. In such IPv6 case
as below, transformation may apply incorrect bundle for the flow instead
of creating another bundle:
- The policy selector has destination prefix length < 128
(Two or more addresses can be matched it)
- Its bundle holds dst entry of default route whose prefix length < 128
(Previous traffic was used such route as next hop)
- The policy and the bundle were used a transport mode state and
this time flow address is not matched the bundled state.
This issue is found by Mobile IPv6 usage to protect mobility signaling
by IPsec, but it is not a Mobile IPv6 specific.
This patch adds strict check to xfrm_bundle_ok() for each
state mode and address when prefix length is less than 128.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch transformation state is updated last used time
for each sending. Xtime is used for it like other state lifetime
expiration.
Mobile IPv6 enabled nodes will want to know traffic status of each
binding (e.g. judgement to request binding refresh by correspondent node,
or to keep home/care-of nonce alive by mobile node).
The last used timestamp is an important hint about it.
Based on MIPL2 kernel patch.
This patch was also written by: Henrik Petander <petander@tcs.hut.fi>
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Care-of address is carried by state as a transformation option like
IPsec encryption/authentication algorithm.
Based on MIPL2 kernel patch.
Signed-off-by: Noriaki TAKAMIYA <takamiya@po.ntts.co.jp>
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
On current kernel inbound transformation state is allowed transport and
disallowed tunnel mode when mismatch is occurred between tempates and states.
As the result of adding two more modes by Mobile IPv6, this function name
is misleading. Inbound transformation can allow only transport mode
when mismatch is occurred between template and secpath.
Based on MIPL2 kernel patch.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
XFRM_STATE_WILDRECV flag is introduced; the last resort state is set
it and receives packet which is not route optimized but uses such
extension headers i.e. Mobile IPv6 signaling (binding update and
acknowledgement). A node enabled Mobile IPv6 adds the state.
Based on MIPL2 kernel patch.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For Mobile IPv6 usage, routing header or destination options header is
used and it doesn't require this comparison. It is checked only for
IPsec template.
Based on MIPL2 kernel patch.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a support to search transformation states by its addresses
by using source address list for Mobile IPv6 usage.
To use it from user-space, it is also added a message type for
source address as a xfrm state option.
Based on MIPL2 kernel patch.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support source address based searching.
Mobile IPv6 will use it.
Based on MIPL2 kernel patch.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It will be added two more transformation protocols (routing header
and destination options header) for Mobile IPv6.
xfrm_id_proto_match() can be handle zero as all, IPSEC_PROTO_ANY as
all IPsec and otherwise as exact one.
Based on MIPL2 kernel patch.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put the helper to header for future use.
Based on MIPL2 kernel patch.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Transformation mode is used as either IPsec transport or tunnel.
It is required to add two more items, route optimization and inbound trigger
for Mobile IPv6.
Based on MIPL2 kernel patch.
This patch was also written by: Ville Nuorvala <vnuorval@tcs.hut.fi>
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This defaults the label of socket-specific IPSec policies to be the
same as the socket they are set on.
Signed-off-by: Venkat Yekkirala <vyekkirala@TrustedCS.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This labels the flows that could utilize IPSec xfrms at the points the
flows are defined so that IPSec policy and SAs at the right label can
be used.
The following protos are currently not handled, but they should
continue to be able to use single-labeled IPSec like they currently
do.
ipmr
ip_gre
ipip
igmp
sit
sctp
ip6_tunnel (IPv6 over IPv6 tunnel device)
decnet
Signed-off-by: Venkat Yekkirala <vyekkirala@TrustedCS.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This includes the security context of a security association created
for use by IKE in the acquire messages sent to IKE daemons using
netlink/xfrm_user. This would allow the daemons to include the
security context in the negotiation, so that the resultant association
is unique to that security context.
Signed-off-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements a seemless mechanism for xfrm policy selection and
state matching based on the flow sid. This also includes the necessary
SELinux enforcement pieces.
Signed-off-by: Venkat Yekkirala <vyekkirala@TrustedCS.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts IPsec to use the new HMAC template. The names of
existing simple digest algorithms may still be used to refer to their
HMAC composites.
The same structure can be used by other MACs such as AES-XCBC-MAC.
This patch also switches from the digest interface to hash.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts IPSec/ESP to use the new block cipher type where
applicable. Similar to the HMAC conversion, existing algorithm names
have been kept for compatibility.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds a compatibility name field for each IPsec algorithm. This
is needed when parameterised algorithms are used. For example, "md5" will
become "hmac(md5)", and "aes" will become "cbc(aes)".
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The header file linux/crypto.h is only needed by a few files so including
it in net/xfrm.h (which is included by half of the networking stack) is a
waste. This patch moves it out of net/xfrm.h and into the specific header
files that actually need it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If dst->obsolete is -1, this is a signal from the
bundle creator that we want the XFRM dst and the
dsts that it references to be validated on every
use.
I misunderstood this intention when I changed
xfrm_dst_check() to always return NULL.
Now, when we purge a dst entry, by running dst_free()
on it. This will set the dst->obsolete to a positive
integer, and we want to return NULL in that case so
that the socket does a relookup for the route.
Thus, if dst->obsolete<0, let stale_bundle() validate
the state, else always return NULL.
In general, we need to do things more intelligently
here because we flush too much state during rule
changes. Herbert Xu has some ideas wherein the key
manager gives us some help in this area. We can also
use smarter state management algorithms inside of
the kernel as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the unused EXPORT_SYMBOL(xfrm_state_mtu).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch encapsulates the usage of eff_cap (in netlink_skb_params) within
the security framework by extending security_netlink_recv to include a required
capability parameter and converting all direct usage of eff_caps outside
of the lsm modules to use the interface. It also updates the SELinux
implementation of the security_netlink_send and security_netlink_recv
hooks to take advantage of the sid in the netlink_skb_params struct.
This also enables SELinux to perform auditing of netlink capability checks.
Please apply, for 2.6.18 if possible.
Signed-off-by: Darrel Goeddel <dgoeddel@trustedcs.com>
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Assignment used as truth value in xfrm_del_sa()
and xfrm_get_policy().
Wrong argument type declared for security_xfrm_state_delete()
when SELINUX is disabled.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains a fix for the previous patch that adds security
contexts to IPsec policies and security associations. In the previous
patch, no authorization (besides the check for write permissions to
SAD and SPD) is required to delete IPsec policies and security
assocations with security contexts. Thus a user authorized to change
SAD and SPD can bypass the IPsec policy authorization by simply
deleteing policies with security contexts. To fix this security hole,
an additional authorization check is added for removing security
policies and security associations with security contexts.
Note that if no security context is supplied on add or present on
policy to be deleted, the SELinux module allows the change
unconditionally. The hook is called on deletion when no context is
present, which we may want to change. At present, I left it up to the
module.
LSM changes:
The patch adds two new LSM hooks: xfrm_policy_delete and
xfrm_state_delete. The new hooks are necessary to authorize deletion
of IPsec policies that have security contexts. The existing hooks
xfrm_policy_free and xfrm_state_free lack the context to do the
authorization, so I decided to split authorization of deletion and
memory management of security data, as is typical in the LSM
interface.
Use:
The new delete hooks are checked when xfrm_policy or xfrm_state are
deleted by either the xfrm_user interface (xfrm_get_policy,
xfrm_del_sa) or the pfkey interface (pfkey_spddelete, pfkey_delete).
SELinux changes:
The new policy_delete and state_delete functions are added.
Signed-off-by: Catherine Zhang <cxzhang@watson.ibm.com>
Signed-off-by: Trent Jaeger <tjaeger@cse.psu.edu>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the structure xfrm_mode. It is meant to represent
the operations carried out by transport/tunnel modes.
By doing this we allow additional encapsulation modes to be added
without clogging up the xfrm_input/xfrm_output paths.
Candidate modes include 4-to-6 tunnel mode, 6-to-4 tunnel mode, and
BEET modes.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of locks used to manage afinfo structures can easily be reduced
down to one each for policy and state respectively. This is based on the
observation that the write locks are only held by module insertion/removal
which are very rare events so there is no need to further differentiate
between the insertion of modules like ipv6 versus esp6.
The removal of the read locks in xfrm4_policy.c/xfrm6_policy.c might look
suspicious at first. However, after you realise that nobody ever takes
the corresponding write lock you'll feel better :)
As far as I can gather it's an attempt to guard against the removal of
the corresponding modules. Since neither module can be unloaded at all
we can leave it to whoever fixes up IPv6 unloading :)
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
xfrm_policy_afinfo_lock can be taken in bh context, at:
[<c013fe1a>] lockdep_acquire_read+0x54/0x6d
[<c0f6e024>] _read_lock+0x15/0x22
[<c0e8fcdb>] xfrm_policy_get_afinfo+0x1a/0x3d
[<c0e8fd10>] xfrm_decode_session+0x12/0x32
[<c0e66094>] ip_route_me_harder+0x1c9/0x25b
[<c0e770d3>] ip_nat_local_fn+0x94/0xad
[<c0e2bbc8>] nf_iterate+0x2e/0x7a
[<c0e2bc50>] nf_hook_slow+0x3c/0x9e
[<c0e3a342>] ip_push_pending_frames+0x2de/0x3a7
[<c0e53e19>] icmp_push_reply+0x136/0x141
[<c0e543fb>] icmp_reply+0x118/0x1a0
[<c0e54581>] icmp_echo+0x44/0x46
[<c0e53fad>] icmp_rcv+0x111/0x138
[<c0e36764>] ip_local_deliver+0x150/0x1f9
[<c0e36be2>] ip_rcv+0x3d5/0x413
[<c0df760f>] netif_receive_skb+0x337/0x356
[<c0df76c3>] process_backlog+0x95/0x110
[<c0df5fe2>] net_rx_action+0xa5/0x16d
[<c012d8a7>] __do_softirq+0x6f/0xe6
[<c0105ec2>] do_softirq+0x52/0xb1
this means that all write-locking of xfrm_policy_afinfo_lock must be
bh-safe. This patch fixes xfrm_policy_register_afinfo() and
xfrm_policy_unregister_afinfo().
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu
Patrick McHardy