Since support for mxc91231 was introduced 2009 it only saw patches that
were part of (mxc or arm) global cleanups. The only supported machine
only had 4 devices (2x UART, sdhc, watchdog).
Cc: Dmitriy Taychenachev <dimichxp@gmail.com>
LAKML-Reference: 1302211482-17926-1-git-send-email-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Implement code for MX51 that allows the SoC to enter WFI when
arch_idle is called.
This patch is also necessary for correctly suspending the system.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Having the silicon revision to appear on the boot log is a useful information.
MX31 and MX35 already show the silicon revision on boot.
Add support for displaying such information for MX51 as well.
Tested on a MX51EVK, where it shows:
CPU identified as i.MX51, silicon rev 3.0
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Move to SOC_SOC_IMX3X.
Leave ARCH_MX31/35 definitions there, in case some place prevent multi-soc
single image.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Move to SOC_SOC_IMX5X. Leave only places which prevent multi-soc
using ARCH_MX5X.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Instead of reading the silicon version from ROM, we should
read the SREV register from the IIM.
Freescale has dropped all support for MX51 REV1.0, only MX51
REV 2.0 and 3.0 are valid.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Currently, only two operating points: 160Mhz and 800Mhz.
the operating points are tested on babbage 3.0
Signed-off-by: Yong Shen <yong.shen@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This has the addional effect that the macros CSCR_U, CSCR_L and CSCR_A
are not used anymore in mach-pcm038.c and mach-qong.c. These still use
the deprecated IO_ADDRESS macro and shouldn't be used in new code.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Holger Schurig <hs4233@mail.mn-solutions.de>
Cc: Dmitriy Taychenachev <dimichxp@gmail.com>
We had hardcoded cpu_is_ macros for mxc architectures till now. As we
want to run the same kernel on i.MX31 and i.MX35 this patch adds cpu_is_
macros which expand to 0 or 1 if only one architecture is compiled in and
only check for the cpu type if more than one architecture is compiled
in.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* define new CONFIG_ARCH_MX21 (this one is currently mutually exclusive to
CONFIG_ARCH_MX27, but this might change)
* splits one header file. Memory definitions, interrupt sources,
DMA channels are split into common part, i.MX27 specific and i.MX21
specific.
* guard access to UART5/UART6, which don't exist on i.MX21
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* adds Kconfig variables
* specifies different physical address for i.MX21 because of the
different memory layouts
* disables support for UART5/UART6 in the i.MX serial driver
(the i.MX21 doesn't have those modules)
Based on code from "Martin Fuzzey" <mfuzzey@gmail.com>
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds macros to get CSCR upper, lower and additional registers.
These registers are needed to configure a chip select line. The offset
layouts of these Registers are identical on mx27 and mx31, hence we can
use the macros in generic way
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sascha Hauer