The new prminst_xxx accessors based on partition and offset
is now used, so removed all the previous prcm_xxx accessors.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: remove fn prototypes also]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The warm reset function was still using the obsolete API.
Replace it by the new one and move the file to the proper c file.
Change the function names to stick to the file convention as
suggested by Paul Walmsley <paul@pwsan.com>:
prm_xxx -> prminst_xxx
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The RSTCTRL register was accessed using an absolute address.
The usage of hardcoded macros to calculate virtual address from physical
one should be avoided as much as possible.
The usage of an offset will allow future improvement like migration from
the current architecture code toward a module driver.
Update prm_xxx accessors, move definition to the proper header file and
update copyrights.
Change the s16 register offset parameter to u16.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: use '_prminst_' in function names that are part of the
prminst44xx.c file]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Move the OMAP4 global software reset function to the OMAP4-specific
prm44xx.c file, where it belongs. Part of the long-term process of
moving all of the direct PRCM register writes into lower-layer code.
Also add OCP barriers on OMAP2/3/4 to reduce the chance that the MPU
will continue executing while the system is supposed to be resetting
itself.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
In some ways, the OMAP4 PRCM register layout is quite different than
the OMAP2/3 PRCM register layout. For example, on OMAP2/3, from a
register layout point of view, all CM instances were located in the CM
subsystem, and all PRM instances were located in the PRM subsystem.
OMAP4 changes this. Now, for example, some CM instances, such as
WKUP_CM and EMU_CM, are located in the system PRM subsystem. And a
"local PRCM" exists for the MPU - this PRCM combines registers that
would normally appear in both CM and PRM instances, but uses its own
register layout which matches neither the OMAP2/3 PRCM layout nor the
OMAP4 PRCM layout.
To try to deal with this, introduce some new functions, omap4_cminst*
and omap4_prminst*. The former is to be used when writing to a CM
instance register (no matter what subsystem or hardware module it
exists in), and the latter, similarly, with PRM instance registers.
To determine which "PRCM partition" to write to, the functions take a
PRCM instance ID argument. Subsequent patches add these partition IDs
to the OMAP4 powerdomain and clockdomain definitions.
As far as I can see, there's really no good way to handle these types
of register access inconsistencies. This patch seemed like the least
bad approach.
Moving forward, the long-term goal is to remove all direct PRCM
register access from the PM code. PRCM register access should go
through layers such as the powerdomain and clockdomain code that can
hide the details of how to interact with the specific hardware
variant.
While here, rename cm4xxx.c to cm44xx.c to match the naming convention
of the other OMAP4 PRCM files.
Thanks to Santosh Shilimkar <santosh.shilimkar@ti.com>, Rajendra Nayak
<rnayak@ti.com>, and Benoît Cousson <b-cousson@ti.com> for some comments.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Split the existing cm44xx.h file into cm1_44xx.h and cm2_44xx.h files
so they match their underlying OMAP hardware modules. Add clockdomain
offset information.
Add header files for the MPU local PRCM, prcm_mpu44xx.h, and for the
SCRM, scrm44xx.h. SCRM register offsets still need to be added; TI
should do this.
Move the "_MOD" macros out of the prcm-common.h header file, into the
header file of the hardware module that they belong to. For example,
OMAP4430_PRM_*_MOD macros have been moved into the prm44xx.h header.
Adjust #includes of all files that used the old PRCM header file names
to point to the new filenames.
The autogeneration scripts have been updated accordingly.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Most processor modules (e.g., DSP, IVA, IPU) on OMAPs can be reset
under the control of the PRM. This patch adds an API for this purpose
for OMAP4 devices:
int omap4_prm_is_hardreset_asserted(void __iomem *rstctrl_reg, u8 shift);
int omap4_prm_assert_hardreset(void __iomem *rstctrl_reg, u8 shift);
int omap4_prm_deassert_hardreset(void __iomem *rstctrl_reg, u8 shift);
This API is intended to be used only by the hwmod code - a subsequent
patch will add that support to hwmod.
This patch is a collaboration between Benoît Cousson <b-cousson@ti.com>
and Paul Walmsley <paul@pwsan.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Benoit Cousson