Driver checks received packet is too large in asix_rx_fixup() and fails if it is. Problem is
that MTU might be set larger than 1500 and asix fails to work correctly with VLAN tagged
packets. The check should be 'dev->net->mtu + ETH_HLEN' instead.
Tested with AX88772.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some configurations need delay between the "write completed" indication
and new write to work reliably.
Realtek driver seems to use longer delay when polling the "write complete"
bit, so it waits long enough between writes with high probability (but
could probably break too). This patch adds a new udelay to make sure we
wait unconditionally some time after the write complete indication.
This caused a regression with XID 18000000 boards when the board specific
phy configuration writing many mdio registers was added in commit
2e955856ff (r8169: phy init for the 8169scd). Some of the configration
mdio writes would almost always fail, and depending on failure might leave
the PHY in non-working state.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Acked-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port of internal scan to iwl3945 missed introduction
of iwl3945_get_single_channel_for_scan.
Fix the following bug by introducing the iwl3945_get_single_channel_for_scan
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2208
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (30 commits)
X25: remove duplicated #include
tcp: use correct net ns in cookie_v4_check()
rps: tcp: fix rps_sock_flow_table table updates
ppp_generic: fix multilink fragment sizes
syncookies: remove Kconfig text line about disabled-by-default
ixgbe: only check pfc bits in hang logic if pfc is enabled
net: check for refcount if pop a stacked dst_entry
ixgbe: return IXGBE_ERR_RAR_INDEX when out of range
act_pedit: access skb->data safely
sfc: Store port number in net_device::dev_id
epic100: Test __BIG_ENDIAN instead of (non-existent) CONFIG_BIG_ENDIAN
tehuti: return -EFAULT on copy_to_user errors
isdn/kcapi: return -EFAULT on copy_from_user errors
e1000e: change logical negate to bitwise
sfc: Get port number from CS_PORT_NUM, not PCI function number
cls_u32: use skb_header_pointer() to dereference data safely
TCP: tcp_hybla: Fix integer overflow in slow start increment
act_nat: fix the wrong checksum when addr isn't in old_addr/mask
net/fec: fix pm to survive to suspend/resume
korina: count RX DMA OVR as rx_fifo_error
...
Remove duplicated #include('s) in drivers/net/wan/x25_asy.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix bug in multilink fragment size calculation introduced by
commit 9c705260fe
"ppp: ppp_mp_explode() redesign"
Signed-off-by: Ben McKeegan <ben@netservers.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only check pfc bits in hang logic if PFC is enabled. Previously,
if DCB was enabled but PFC was disabled the incorrect pause
bits would be checked.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 56d1de0a21, "ath5k: clean up
filter flags setting" introduced a regression in monitor mode such
that the promisc filter flag would get lost.
Although we set the promisc flag when it changed, we did not
preserve it across subsequent calls to configure_filter. This patch
restores the original functionality.
Cc: stable@kernel.org
Bisected-by: weedy2887@gmail.com
Tested-by: weedy2887@gmail.com
Tested-by: Rick Farina <sidhayn@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When building a kernel with CONFIG_PM=y but neither suspend nor
hibernate support, the compiler complains about the static functions
ath5k_pci_suspend() and ath5k_pci_resume() not being used:
drivers/net/wireless/ath/ath5k/base.c:713:12: warning: ‘ath5k_pci_suspend’ defined but not used
drivers/net/wireless/ath/ath5k/base.c:722:12: warning: ‘ath5k_pci_resume’ defined but not used
Depending on CONFIG_PM_SLEEP rather than CONFIG_PM fixes the issue.
Signed-off-by: Tobias Doerffel <tobias.doerffel@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/macio: Fix probing of macio devices by using the right of match table
agp/uninorth: Fix oops caused by flushing too much
powerpc/pasemi: Update MAINTAINERS file
powerpc/cell: Fix integer constant warning
powerpc/kprobes: Remove resume_execution() in kprobes
powerpc/macio: Don't dereference pointer before null check
Based on original patch from Shirley Ma <xma@us.ibm.com>
Return IXGBE_ERR_RAR_INDEX when RAR index is out of range, instead of
returning IXGBE_SUCCESS.
CC: Shirley Ma <xma@us.ibm.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This exposes the port number to userland through sysfs.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Probably no one has used this driver on big-endian systems, since it was
setting up descriptor swapping if CONFIG_BIG_ENDIAN is set, which it
never is, since that symbol is not mentioned anywhere else in the kernel
source. Switch this test to a check for __BIG_ENDIAN so it has a chance
at working.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
copy_to_user() returns the number of bytes remaining but we want to
return a negative error code here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bitwise negate is intended here. With the logical negate the
condition is always false.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A single shared memory region used to communicate with firmware is
mapped into both PCI PFs of the SFC9020 and SFL9021. Drivers must be
able to identify which port they are addressing in order to use the
correct sub-region. Currently we use the PCI function number, but the
PCI address may be virtualised. Use the CS_PORT_NUM register field
defined for just this purpose.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes build error caused by the OF device_node
pointer being moved into struct device
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* in the actual driver, calling fec_stop and fec_enet_init doesn't
allow to have a working network interface at resume (where a
ifconfig down and up is required to recover the interface)
* by using fec_enet_close and fec_enet_open, this patch solves this
problem and handle the case where the link changed between suspend
and resume
* this patch also disable clock at suspend and reenable it at resume
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This way, RX DMA overruns (actually being caused by overrun of the
512byte input FIFO) show up in ifconfig output. The rx_fifo_errors
counter is unused otherwise.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch completes commit 89d71a66c4
which missed this spot, as it seems.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
By calling korina_restart(), the IRQ handler tries to disable the
interrupt it's currently serving. This leads to a deadlock since
disable_irq() waits for any running IRQ handlers to finish before
returning. This patch addresses the issue by turning korina_restart()
into a workqueue task, which is then scheduled when needed.
Reproducing the deadlock is easily done using e.g. GNU netcat to send
large amounts of UDP data to the host running this driver.
Note that the same problem (and fix) applies to TX FIFO underruns, but
apparently these are less easy to trigger.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make get/set netlink VF_PORT truly symmetrical, we need to keep track
of what items are set and only return those items on get. Previously, the
driver wasn't differentiating between a set of attr with a NULL string,
for example, and not setting the attr at all. We only want to return
the NULL string if the attr was actually set with a NULL string. Otherwise,
don't return the attr.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The regression is caused by:
commit 4327ba435a
bnx2: Fix netpoll crash.
If ->open() and ->close() are called multiple times, the same napi structs
will be added to dev->napi_list multiple times, corrupting the dev->napi_list.
This causes free_netdev() to hang during rmmod.
We fix this by calling netif_napi_del() during ->close().
Also, bnx2_init_napi() must not be in the __devinit section since it is
called by ->open().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grant patches added an of mach table to struct device_driver. However,
while he changed the macio device code to use that, he left the match
table pointer in struct macio_driver and didn't update drivers to use
the "new" one, thus breaking the probing.
This completes the change by moving all drivers to setup the "new"
one, removing all traces of the old one, and while at it (since it
changes the exact same locations), I also remove two other duplicates
from struct driver which are the name and owner fields.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We can wake all queues after a chip reset since everything should be set up and
we are ready to transmit. If we don't do that we might end up starting up with
stopped queues, not beeing able to transmit. (This started to happen after
"ath5k: clean up queue manipulation" but since periodic calibration also
stopped and started the queues this effect was hidden most of the time).
This way we can also get rid of the superfluous ath5k_reset_wake() function.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
virtio-net bounces buffer allocations off to
a thread if it can't allocate buffers from the atomic
pool. However, if posting buffers still requires atomic
buffers, this is unlikely to succeed.
Fix by passing in the proper gfp_t parameter.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code fails on ppc as hdr.timeout is not being converted
to le32.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes build error caused by the OF device_node pointer
being moved into struct device.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (47 commits)
mfd: Rename twl5031 sih modules
mfd: Storage class for timberdale should be before const qualifier
mfd: Remove unneeded and dangerous clearing of clientdata
mfd: New AB8500 driver
gpio: Fix inverted rdc321x gpio data out registers
mfd: Change rdc321x resources flags to IORESOURCE_IO
mfd: Move pcf50633 irq related functions to its own file.
mfd: Use threaded irq for pcf50633
mfd: pcf50633-adc: Fix potential race in pcf50633_adc_sync_read
mfd: Fix pcf50633 bitfield logic in interrupt handler
gpio: rdc321x needs to select MFD_CORE
mfd: Use menuconfig for quicker config editing
ARM: AB3550 board configuration and irq for U300
mfd: AB3550 core driver
mfd: AB3100 register access change to abx500 API
mfd: Renamed ab3100.h to abx500.h
gpio: Add TC35892 GPIO driver
mfd: Add Toshiba's TC35892 MFD core
mfd: Delay to mask tsc irq in max8925
mfd: Remove incorrect wm8350 kfree
...
This fixes some sparse warnings:
drivers/net/benet/be_cmds.c:1503:12: warning: function
'be_cmd_enable_magic_wol' with external linkage has definition
drivers/net/benet/be_cmds.c:1668:12: warning: function
'be_cmd_get_seeprom_data' with external linkage has definition
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The unlock accidentally got removed from the error path in dd131e76e5:
"be2net: Bug fix to avoid disabling bottom half during firmware upgrade."
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an occasional transmit lockup in the mac-fcc which
occurs after a tx error. The test scenario had the local port set
to autoneg and the other end fixed at 100FD, resulting in a large
number of late collisions.
According to the MPC8280RM 30.10.1.3 (also 8272RM 29.10.1.3), after
a tx error occurs, TBPTR may sometimes point beyond BDs still marked
as ready. This patch walks back through the BDs and points TBPTR to
the earliest one marked as ready.
Tested on a custom board with a MPC8280.
Signed-off-by: Mark Ware <mware@elphinstone.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes:
drivers/net/wireless/libertas/rx.c: In function process_rxed_802_11_packet:
drivers/net/wireless/libertas/rx.c:354: error: radiotap_hdr.flags may be used uninitialized in this function
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This bug was introduced by the following commit
Author: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Date: Thu Apr 15 17:38:46 2010 -0400
ath9k: Remove ATH9K_TX_SW_ABORTED and introduce a bool for this purpose
Wrong buffer is checked for bf_tx_aborted field in ath_tx_num_badfrms(),
this may result in a rate scaling with wrong feedback (number
of unacked frames in this case). It is the last one in the chain
of buffers for an aggregate frame that should be checked.
Also it misses the initialization of this field in the buffer,
this may lead to a situation where we stop the sw retransmission
of failed subframes associated to this buffer.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_print in xmit.c should say "Reseting hardware"
instead of Resetting HAL!(since HAL is being fazed out).
dmesg shows:
[ 8660.899624] ath: Failed to stop TX DMA in 100 msec after killing last frame
[ 8660.899676] ath: Unable to stop TxDMA. Reset HAL!
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (22 commits)
netlink: bug fix: wrong size was calculated for vfinfo list blob
netlink: bug fix: don't overrun skbs on vf_port dump
xt_tee: use skb_dst_drop()
netdev/fec: fix ifconfig eth0 down hang issue
cnic: Fix context memory init. on 5709.
drivers/net: Eliminate a NULL pointer dereference
drivers/net/hamradio: Eliminate a NULL pointer dereference
be2net: Patch removes redundant while statement in loop.
ipv6: Add GSO support on forwarding path
net: fix __neigh_event_send()
vhost: fix the memory leak which will happen when memory_access_ok fails
vhost-net: fix to check the return value of copy_to/from_user() correctly
vhost: fix to check the return value of copy_to/from_user() correctly
vhost: Fix host panic if ioctl called with wrong index
net: fix lock_sock_bh/unlock_sock_bh
net/iucv: Add missing spin_unlock
net: ll_temac: fix checksum offload logic
net: ll_temac: fix interrupt bug when interrupt 0 is used
sctp: dubious bitfields in sctp_transport
ipmr: off by one in __ipmr_fill_mroute()
...
BugLink: http://bugs.launchpad.net/bugs/559065
In fec open/close function, we need to use phy_connect and phy_disconnect
operation before we start/stop phy. Otherwise it will cause system hang.
Only call fec_enet_mii_probe() in open function, because the first open
action will cause NULL pointer error.
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to zero context memory on 5709 in the function cnic_init_context().
Without this, iscsid restart on 5709 will not work because of stale data.
TX context blocks should not be initialized by cnic_init_context() because
of the special remapping on 5709.
Update version to 2.1.2.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the point of the print, dev is NULL.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression E,E1;
identifier f;
statement S1,S2,S3;
@@
if ((E == NULL && ...) || ...)
{
... when != if (...) S1 else S2
when != E = E1
* E->f
... when any
return ...;
}
else S3
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the point of the print, dev is NULL.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression E,E1;
identifier f;
statement S1,S2,S3;
@@
if ((E == NULL && ...) || ...)
{
... when != if (...) S1 else S2
when != E = E1
* E->f
... when any
return ...;
}
else S3
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Janz VMOD-ICAN3 is a MODULbus daughterboard which fits onto any
MODULbus carrier board. It is an intelligent CAN controller with a
microcontroller and associated firmware.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The current checksum offload code does not work and this corrects
that functionality. It also updates the interrupt coallescing
initialization so than there are fewer interrupts and performance
is increased.
Signed-off-by: Brian Hill <brian.hill@xilinx.com>
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code is not checking the interrupt for DMA correctly so that an
interrupt number of 0 will cause a false error.
Signed-off-by: Brian Hill <brian.hill@xilinx.com>
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 663cb47cc2.
This patch was merged out of the proper order, so instead of fixing a
problem with a prior (unmerged) patch, it creates one. Ooops!
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes BE requires longer time for POST completion after an EEH
reset. Increasing the timeout value accordingly.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (63 commits)
drivers/net/usb/asix.c: Fix pointer cast.
be2net: Bug fix to avoid disabling bottom half during firmware upgrade.
proc_dointvec: write a single value
hso: add support for new products
Phonet: fix potential use-after-free in pep_sock_close()
ath9k: remove VEOL support for ad-hoc
ath9k: change beacon allocation to prefer the first beacon slot
sock.h: fix kernel-doc warning
cls_cgroup: Fix build error when built-in
macvlan: do proper cleanup in macvlan_common_newlink() V2
be2net: Bug fix in init code in probe
net/dccp: expansion of error code size
ath9k: Fix rx of mcast/bcast frames in PS mode with auto sleep
wireless: fix sta_info.h kernel-doc warnings
wireless: fix mac80211.h kernel-doc warnings
iwlwifi: testing the wrong variable in iwl_add_bssid_station()
ath9k_htc: rare leak in ath9k_hif_usb_alloc_tx_urbs()
ath9k_htc: dereferencing before check in hif_usb_tx_cb()
rt2x00: Fix rt2800usb TX descriptor writing.
rt2x00: Fix failed SLEEP->AWAKE and AWAKE->SLEEP transitions.
...
Stephen Rothwell reports the following new warning:
drivers/net/usb/asix.c: In function 'asix_rx_fixup':
drivers/net/usb/asix.c:325: warning: cast from pointer to integer of different size
drivers/net/usb/asix.c:354: warning: cast from pointer to integer of different size
The code just cares about the low alignment bits, so use
an "unsigned long" cast instead of one to "u32".
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain firmware commands/operations to upgrade firmware could take several
seconds to complete. The code presently disables bottom half during these
operations which could lead to unpredictable behaviour in certain cases. This
patch now does all firmware upgrade operations asynchronously using a
completion variable.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a few new product id's for the hso driver.
Signed-off-by: Filip Aben <f.aben@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds:
alias: devname:<name>
to some common kernel modules, which will allow the on-demand loading
of the kernel module when the device node is accessed.
Ideally all these modules would be compiled-in, but distros seems too
much in love with their modularization that we need to cover the common
cases with this new facility. It will allow us to remove a bunch of pretty
useless init scripts and modprobes from init scripts.
The static device node aliases will be carried in the module itself. The
program depmod will extract this information to a file in the module directory:
$ cat /lib/modules/2.6.34-00650-g537b60d-dirty/modules.devname
# Device nodes to trigger on-demand module loading.
microcode cpu/microcode c10:184
fuse fuse c10:229
ppp_generic ppp c108:0
tun net/tun c10:200
dm_mod mapper/control c10:235
Udev will pick up the depmod created file on startup and create all the
static device nodes which the kernel modules specify, so that these modules
get automatically loaded when the device node is accessed:
$ /sbin/udevd --debug
...
static_dev_create_from_modules: mknod '/dev/cpu/microcode' c10:184
static_dev_create_from_modules: mknod '/dev/fuse' c10:229
static_dev_create_from_modules: mknod '/dev/ppp' c108:0
static_dev_create_from_modules: mknod '/dev/net/tun' c10:200
static_dev_create_from_modules: mknod '/dev/mapper/control' c10:235
udev_rules_apply_static_dev_perms: chmod '/dev/net/tun' 0666
udev_rules_apply_static_dev_perms: chmod '/dev/fuse' 0666
A few device nodes are switched to statically allocated numbers, to allow
the static nodes to work. This might also useful for systems which still run
a plain static /dev, which is completely unsafe to use with any dynamic minor
numbers.
Note:
The devname aliases must be limited to the *common* and *single*instance*
device nodes, like the misc devices, and never be used for conceptually limited
systems like the loop devices, which should rather get fixed properly and get a
control node for losetup to talk to, instead of creating a random number of
device nodes in advance, regardless if they are ever used.
This facility is to hide the mess distros are creating with too modualized
kernels, and just to hide that these modules are not compiled-in, and not to
paper-over broken concepts. Thanks! :)
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Alasdair G Kergon <agk@redhat.com>
Cc: Tigran Aivazian <tigran@aivazian.fsnet.co.uk>
Cc: Ian Kent <raven@themaw.net>
Signed-Off-By: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/nes: Fix incorrect unlock in nes_process_mac_intr()
RDMA/nes: Async event for closed QP causes crash
RDMA/nes: Have ethtool read hardware registers for rx/tx stats
RDMA/cxgb4: Only insert sq qid in lookup table
RDMA/cxgb4: Support IB_WR_READ_WITH_INV opcode
RDMA/cxgb4: Set fence flag for inv-local-stag work requests
RDMA/cxgb4: Update some HW limits
RDMA/cxgb4: Don't limit fastreg page list depth
RDMA/cxgb4: Return proper errors in fastreg mr/pbl allocation
RDMA/cxgb4: Fix overflow bug in CQ arm
RDMA/cxgb4: Optimize CQ overflow detection
RDMA/cxgb4: CQ size must be IQ size - 2
RDMA/cxgb4: Register RDMA provider based on LLD state_change events
RDMA/cxgb4: Detach from the LLD after unregistering RDMA device
IB/ipath: Remove support for QLogic PCIe QLE devices
IB/qib: Add new qib driver for QLogic PCIe InfiniBand adapters
IB/mad: Make needlessly global mad_sendq_size/mad_recvq_size static
IB/core: Allow device-specific per-port sysfs files
mlx4_core: Clean up mlx4_alloc_icm() a bit
mlx4_core: Fix possible chunk sg list overflow in mlx4_alloc_icm()
With VEOL, Beacon transmission in ad-hoc does not currently work.
I believe for larger ad-hoc networks, VEOL is too unreliable, as
it can get beacon transmissions stuck during synchronization.
Use SWBA based beacon trasmission similar to AP mode instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes IBSS beacon transmissions without VEOL enabled
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of using own implementation involve hex_to_bin() function.
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes possible memory leak.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI function reset needs to invoked after fw init ioctl is issued.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functionality to keep the device awake until it is done with
the rx of any mcast/bcast frames which are pending on AP should
also be added to the hardwares which support auto sleep feature.
This patch fixes frequent failures in ARP resolution when it is
initiated by the other end. Currently auto sleep is enabled only
for ar9003 in ath9k.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The intent here is to test that "sta_id_r" is a valid pointer. We do
this same test later on in the function.
Btw iwl_add_bssid_station() is called from two places and "sta_id_r" is
a valid pointer from both callers.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is obviously a small picky thing. The original error handling code
doesn't free the most recent allocations which haven't been added to the
hif_dev->tx.tx_buf list yet.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After c11d8f89d3: "ath9k_htc: Simplify TX URB management" we no longer
assume that tx_buf is a non-null pointer.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The recent changes to skb handling introduced a bug in the rt2800usb
TX descriptor writing whereby the length of the USB packet wasn't
calculated correctly.
Found via code inspection, as the devices themselves didn't seem to mind.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(Based on a patch created by Ondrej Zary)
In some circumstances the Ralink devices do not properly go to sleep
or wake up, with timeouts occurring.
Fix this by retrying telling the device that it has to wake up or
sleep.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 03ceedea97.
This patch was reported to cause a regression in which connectivity is
lost and cannot be reestablished after a suspend/resume cycle.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implicit slab.h inclusion via percpu.h is about to go away. Make sure
gfp.h or slab.h is included as necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't use to_pci_dev in rt2x00pci_uninitialize to get the allocated irq
as it won't work for platform devices (SoC). Instead, use the irq field
that's already used everywhere else.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should use the same buffer size we set up for DMA also in the hardware
descriptor. Previously we used common->rx_bufsize for setting up the DMA
mapping, but used skb_tailroom(skb) for the size we tell to the hardware in the
descriptor itself. The problem is that skb_tailroom(skb) can give us a larger
value than the size we set up for DMA before. This allows the hardware to write
into memory locations not set up for DMA. In practice this should rarely happen
because all packets should be smaller than the maximum 802.11 packet size.
On the tested platform rx_bufsize is 2528, and we allocated an skb of 2559
bytes length (including padding for cache alignment) but sbk_tailroom() was
2592. Just consistently use rx_bufsize for all RX DMA memory sizes.
Also use the return value of the descriptor setup function.
Cc: stable@kernel.org
Signed-off-by: Bruno Randolf <br1@einfach.org>
Reviewed-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 03ceedea97, since it
breaks resume from suspend-to-ram on Rafael's Acer Ferrari One.
NetworkManager thinks everything is ok, but it can't connect to the AP
to get an IP address after the resume.
In fact, it even breaks resume for non-ath9k chipsets: reverting it also
fixes Rafael's Toshiba Protege R500 with the iwlagn driver. As Johannes
says:
"Indeed, this patch needs to be reverted. That mac80211 change is wrong
and completely unnecessary."
Reported-and-requested-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Daniel Yingqiang Ma <yma.cool@gmail.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The i.MX25 PDK uses RMII to communicate with its PHY. This patch adds
the ability to configure RMII, based on platform data.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes tun update its socket classid every time we
inject a packet into the network stack. This is so that any
updates made by the admin to the process writing packets to
tun is effected.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Anomaly 05000230 (over sampling of the UART STOP bit) applies only when
the peripheral is operating in UART mode. So drop the anomaly handling
in the IRDA code.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This assignment got deleted along with the checks by mistake. This
comes from: 8753d29fd "pppoe: remove unnecessary checks in
pppoe_flush_dev"
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan reported the patch 0baa080c75: "ethoc: use system memory
as buffer" introduced a potential null dereference.
1060 free:
1061 if (priv->dma_alloc)
^^^^^^^^^^^^^^^
priv can be null here.
He also suggested that the error handling is not complete.
This patch fixes the null priv issue and improves resources
releasing in ethoc_probe() and ethoc_remove().
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use random mac addr for interface when associating port-profile to
dynamic enic device, in the case no mac addr was previous assigned.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merging in current state of Linus' tree to deal with merge conflicts and
build failures in vio.c after merge.
Conflicts:
drivers/i2c/busses/i2c-cpm.c
drivers/i2c/busses/i2c-mpc.c
drivers/net/gianfar.c
Also fixed up one line in arch/powerpc/kernel/vio.c to use the
correct node pointer.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
.name, .match_table and .owner are duplicated in both of_platform_driver
and device_driver. This patch is a removes the extra copies from struct
of_platform_driver and converts all users to the device_driver members.
This patch is a pretty mechanical change. The usage model doesn't change
and if any drivers have been missed, or if anything has been fixed up
incorrectly, then it will fail with a compile time error, and the fixup
will be trivial. This patch looks big and scary because it touches so
many files, but it should be pretty safe.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
* 'virtio' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus: (27 commits)
drivers/char: Eliminate use after free
virtio: console: Accept console size along with resize control message
virtio: console: Store each console's size in the console structure
virtio: console: Resize console port 0 on config intr only if multiport is off
virtio: console: Add support for nonblocking write()s
virtio: console: Rename wait_is_over() to will_read_block()
virtio: console: Don't always create a port 0 if using multiport
virtio: console: Use a control message to add ports
virtio: console: Move code around for future patches
virtio: console: Remove config work handler
virtio: console: Don't call hvc_remove() on unplugging console ports
virtio: console: Return -EPIPE to hvc_console if we lost the connection
virtio: console: Let host know of port or device add failures
virtio: console: Add a __send_control_msg() that can send messages without a valid port
virtio: Revert "virtio: disable multiport console support."
virtio: add_buf_gfp
trans_virtio: use virtqueue_xxx wrappers
virtio-rng: use virtqueue_xxx wrappers
virtio_ring: remove a level of indirection
virtio_net: use virtqueue_xxx wrappers
...
Fix up conflicts in drivers/net/virtio_net.c due to new virtqueue_xxx
wrappers changes conflicting with some other cleanups.
Remove (hopefully) last use of WEXT in rndis_wlan. Replace wireless_send_event
with missing cfg80211_disconnected in rndis_wlan_do_link_down_work.
Reported-by: "Rogério Brito" <rbrito@ime.usp.br>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We tried to squeeze as much AR9003 support into this kernel
release cycle but there are a few features which are still
being tested and developed. Some of these features are critical
to the stable operation of AR9003 so for now disable AR9003 support
all together. This will get re-enabled once all necessary features
are in place but very likely will not happen for 2.6.35.
Reviewed-by: Don Breslin <don.breslin@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current frame length used by the driver for RX frames is the SPI bus
transfer length. This length has padding bytes, which do not belong to the
WLAN frame.
As there is no other length information in the WLAN frame except the skb
length this problem caused for instance extra ESSID's to be listed at the
end of scan results (IE id 0) with zero length.
Fix the frame length by removing padding.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is possible for internal scan to race against itself if the device is
not returning the scan results from first requests. What happens in this
case is the cleanup done during the abort of the first internal scan also
cleans up part of the new scan, causing it to access memory it shouldn't.
Here are details:
* First internal scan is triggered and scan command sent to device.
* After seven seconds there is no scan results so the watchdog timer
triggers a scan abort.
* The scan abort succeeds and a SCAN_COMPLETE_NOTIFICATION is received for
failed scan.
* During processing of SCAN_COMPLETE_NOTIFICATION we clear STATUS_SCANNING
and queue the "scan_completed" work.
** At this time, since the problem that caused the internal scan in first
place is still present, a new internal scan is triggered.
The behavior at this point is a bit different between 2.6.34 and 2.6.35
since 2.6.35 has a lot of this synchronized. The rest of the race
description will thus be generalized.
** As part of preparing for the scan "is_internal_short_scan" is set to
true.
* At this point the completion work for fist scan is run. As part of this
there is some locking missing around the "is_internal_short_scan"
variable and it is set to "false".
** Now the second scan runs and it considers itself a real (not internal0
scan and thus causes problems with wrong memory being accessed.
The fix is twofold.
* Since "is_internal_short_scan" should be protected by mutex, fix this in
scan completion work so that changes to it can be serialized.
* Do not queue a new internal scan if one is in progress.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=15824
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows bin_attr->read,write,mmap callbacks to check file specific data
(such as inode owner) as part of any privilege validation.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The semaphore is semantically a mutex. Convert it to a real mutex and
fix up a few places where code was relying on semaphore.h to be included
by device.h, as well as the users of the trylock function, as that value
is now reversed.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As remarked by Sam Ravnborg the spin_lock variable, that has been introduced
in commit 57c8a45664 ("can: Fix SJA1000 command
register writes on SMP systems") has not been initialized properly.
This patch adds the initialization to allow spinlock debugging.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
CC: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocated memory for IRQs should be freed when releasing the mii_bus
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for a new copper device for 82599, device id 0x151c.
This 82599 10GBase-T device uses the PHY's internal temperature sensor
to guard against over-temp conditions. In this scenario the PHY will be
put in a low power mode and link will no longer be able to transmit or
receive any data. When this occurs, the over-temp interrupt is latched
and driver logs this error message. A HW reset or power cycle is
required to clear this status.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits)
qlcnic: adding co maintainer
ixgbe: add support for active DA cables
ixgbe: dcb, do not tag tc_prio_control frames
ixgbe: fix ixgbe_tx_is_paused logic
ixgbe: always enable vlan strip/insert when DCB is enabled
ixgbe: remove some redundant code in setting FCoE FIP filter
ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
ixgbe: fix header len when unsplit packet overflows to data buffer
ipv6: Never schedule DAD timer on dead address
ipv6: Use POSTDAD state
ipv6: Use state_lock to protect ifa state
ipv6: Replace inet6_ifaddr->dead with state
cxgb4: notify upper drivers if the device is already up when they load
cxgb4: keep interrupts available when the ports are brought down
cxgb4: fix initial addition of MAC address
cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
cnic: Convert cnic_local_flags to atomic ops.
can: Fix SJA1000 command register writes on SMP systems
bridge: fix build for CONFIG_SYSFS disabled
ARCNET: Limit com20020 PCI ID matches for SOHARD cards
...
Fix up various conflicts with pcmcia tree drivers/net/
{pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and
wireless/orinoco/spectrum_cs.c} and feature removal
(Documentation/feature-removal-schedule.txt).
Also fix a non-content conflict due to pm_qos_requirement getting
renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c
Handle the allocation error case first, so that we don't have further
nested if for handling the common case of success.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If the number of sg entries in the ICM chunk reaches MLX4_ICM_CHUNK_LEN,
we must set chunk to NULL even for coherent mappings so that the next
time through the loop will allocate another chunk. Otherwise we'll
overflow the sg list the next time through the loop. This will lead to
memory corruption if this case is hit.
mthca does not have this bug.
Signed-off-by: Sebastien Dugue <sebastien.dugue@bull.net>
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch (as1373) fixes a couple of drivers outside the USB
subtree. Devices are now disabled or enabled for autosuspend by
calling a core function instead of setting a flag.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For more clearance what the functions actually do,
usb_buffer_alloc() is renamed to usb_alloc_coherent()
usb_buffer_free() is renamed to usb_free_coherent()
They should only be used in code which really needs DMA coherency.
All call sites have been changed accordingly, except for staging
drivers.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Pedro Ribeiro <pedrib@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The i2400m->rx_roq data structure is protected against race conditions
with a reference count (i2400m->rx_roq_refcount); the pointer can be
read-referenced under the i2400m->rx_lock spinlock.
The code in i2400m_rx_edata() wasn't properly following access
protocol, performing an invalid check on i2400m->rx_roq (which is
cleared to NULL when the refcount drops to zero). As such, it was
missing to detect when the data structure is no longer valid and
oopsing with a NULL pointer dereference.
This commit fixes said check by verifying, under the rx_lock spinlock,
that i2400m->rx_roq is non-NULL and then increasing the reference
count before dropping the spinlock.
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (44 commits)
vlynq: make whole Kconfig-menu dependant on architecture
add descriptive comment for TIF_MEMDIE task flag declaration.
EEPROM: max6875: Header file cleanup
EEPROM: 93cx6: Header file cleanup
EEPROM: Header file cleanup
agp: use NULL instead of 0 when pointer is needed
rtc-v3020: make bitfield unsigned
PCI: make bitfield unsigned
jbd2: use NULL instead of 0 when pointer is needed
cciss: fix shadows sparse warning
doc: inode uses a mutex instead of a semaphore.
uml: i386: Avoid redefinition of NR_syscalls
fix "seperate" typos in comments
cocbalt_lcdfb: correct sections
doc: Change urls for sparse
Powerpc: wii: Fix typo in comment
i2o: cleanup some exit paths
Documentation/: it's -> its where appropriate
UML: Fix compiler warning due to missing task_struct declaration
UML: add kernel.h include to signal.c
...
Switch virtio_net to new virtqueue_xxx wrappers.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This patch adds support of active DA cables. This is
renaming and adding some PHY type enumerations.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network stack indicate packets should not be DCB
tagged by setting the priority to TC_PRIO_CONTROL. One
usage for this is lldp frames which are not suppossed
to be tagged.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TFCS bits show the current XON state. Meaning that the
device is paused if these bits are 0. This fixes the logic
to work as it was intended.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when DCB mode is on, we want the HW VLAN stripping to be always enabled.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ETQS setup for FIP out side the if..else is enough for the ETQS
setup for FIP, so remove redundant code.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure we point to the right offset of the fc_frame_header when
VLAN header exists and HW has VLAN stripping disabled.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When in packet split mode, packet type is not recognized, and the packet is
larger than the header size, the 82599 overflows the packet into the data
area, but doesn't set the HDR_LEN field. We can safely assume the length
is the current header size. This fixes an obscure corner case that can be
triggered by non-ip packet headers or (more likely) by disabling the L2
packet recognition.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upper layer drivers aren't notified that a device is ready if their modules
load after the device becomes ready. Add the missing notification.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PF driver needs to remain alert while its ports are down to service
requests or errors from virtual functions or FW so keep interrupts and
queues available when the ports are brought down. The change makes
open_device_map unnecessary so remove it.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to add the MAC address during link initialization wasn't adding the
address to one of the HW tables. Fix.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Everytime the iSCSI ring finishes setup or shutdown, we need to return
the SPQ (slow path queue) credit to the bnx2x driver. Without this step,
the SPQ will eventually be full causing iSCSI to fail. This can happen
after 3 or 4 MTU changes for example.
Add code to wait for these slow path commands to complete in the RX ring
and return the SPQ credit to bnx2x.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is easier to expand the flags for other purposes because it does
not require a spin_lock. The next bug fix patch needs a flag in
cnic_local_flags.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following structure elements duplicate the information in
'struct device.of_node' and so are being eliminated. This patch
makes all readers of these elements use device.of_node instead.
(struct of_device *)->node
(struct dev_archdata *)->prom_node (sparc)
(struct dev_archdata *)->of_node (powerpc & microblaze)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The SJA1000 command register is concurrently written in the rx-path to free
the receive buffer _and_ in the tx-path to start the transmission.
The SJA1000 data sheet, 6.4.4 COMMAND REGISTER (CMR) states:
"Between two commands at least one internal clock cycle is needed in
order to proceed. The internal clock is half of the external oscillator
frequency."
On SMP systems the current implementation leads to a write stall in the
tx-path, which can be solved by adding some general locking and some time
to settle the write_reg() operation for the command register.
Thanks to Klaus Hitschler for the original fix and detailed problem
description.
This patch applies on net-2.6 and (with some offsets) on net-next-2.6 .
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SH SOHARD ARCNET cards are implemented using generic PLX Technology
PCI<->IOBus bridges. Subvendor and subdevice IDs were not specified,
causing the driver to attach to any such bridge and likely crash the
system by attempting to initialize an unrelated device.
Fix by specifying subvendor and subdevice according to the values found
in the PCI-ID Repository at http://pci-ids.ucw.cz/ .
Cc: stable@kernel.org
Signed-off-by: Andreas Bombe <aeb@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hi,
- This patch removes pppoe_ioctl() declaration in
drivers/net/pppoe.c as it is unneeded.
Regards,
Rami Rosen
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use kcalloc or kzalloc rather than the combination of kmalloc and memset.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,y,flags;
statement S;
type T;
@@
x =
- kmalloc
+ kcalloc
(
- y * sizeof(T),
+ y, sizeof(T),
flags);
if (x == NULL) S
-memset(x, 0, y * sizeof(T));
@@
expression x,size,flags;
statement S;
@@
-x = kmalloc(size,flags);
+x = kzalloc(size,flags);
if (x == NULL) S
-memset(x, 0, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use kzalloc rather than the combination of kmalloc and memset.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,size,flags;
statement S;
@@
-x = kmalloc(size,flags);
+x = kzalloc(size,flags);
if (x == NULL) S
-memset(x, 0, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use kzalloc rather than the combination of kmalloc and memset.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,size,flags;
statement S;
@@
-x = kmalloc(size,flags);
+x = kzalloc(size,flags);
if (x == NULL) S
-memset(x, 0, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add enic ndo_{set|get}_vf_port ops to support setting/getting
port-profile for enic dynamic devices. Enic dynamic devices are just like
normal enic eth devices except dynamic enics require an extra configuration
step to assign a port-profile identifier to the interface before the
interface is useable. Once a port-profile is assigned, link comes up on the
interface and is ready for I/O. The port-profile is used to configure the
network port assigned to the interface. The network port configuration
includes VLAN membership, QoS policies, and port security settings typical
of a data center network.
A dynamic enic initially has a zero-mac address. Before a port-profile is
assigned, a valid non-zero unicast mac address should be assign to the
dynamic enic interface.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
switch and while statements don't need semicolons at end of statement
[ Fixup minor conflicts with recent wimax merge... -DaveM ]
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The member "clock" of struct "sja1000_platform_data" is documented as
"CAN bus oscillator frequency in Hz" but it's actually used as the CAN
clock frequency, which is half of it. To avoid further confusion, this
patch fixes it by renaming the member to "osc_freq". That way, also
non mainline users will notice the change. The platform code for the
relevant boards is updated accordingly. Furthermore, pre-defined
values are now used for the members "ocr" and "cdr".
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
dm9000_set_rx_csum and dm9000_hash_table are called from atomic context (in
dm9000_init_dm9000), and from non-atomic context (via ethtool_ops and
net_device_ops respectively). This causes a spinlock recursion BUG. Fix this by
renaming these functions to *_unlocked for the atomic context, and make the
original functions locking wrappers for use in the non-atomic context.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use kmemdup when some other buffer is immediately copied into the
allocated region.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
statement S;
@@
- to = \(kmalloc\|kzalloc\)(size,flag);
+ to = kmemdup(from,size,flag);
if (to==NULL || ...) S
- memcpy(to, from, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use kmemdup when some other buffer is immediately copied into the
allocated region.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
statement S;
@@
- to = \(kmalloc\|kzalloc\)(size,flag);
+ to = kmemdup(from,size,flag);
if (to==NULL || ...) S
- memcpy(to, from, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use kmemdup when some other buffer is immediately copied into the
allocated region.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
statement S;
@@
- to = \(kmalloc\|kzalloc\)(size,flag);
+ to = kmemdup(from,size,flag);
if (to==NULL || ...) S
- memcpy(to, from, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver could return success code even if mdiobus_alloc() failed.
This patch fixes the issue.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current link checking logic only works for one port, which is not correct
for swiches were multiple ports can have different link status. As a result
we would only check for link status on port 1 of the switch. Move the calls
to mii_check_media in r6040_timer which will be polling a single PHY chip
correctly and assume link is up for switches.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
These callbacks were needed because dev_pm_ops support for OF
platform devices was in the powerpc tree, and the patch that
added dev_pm_ops for gianfar driver was in the netdev tree. Now
that netdev and powerpc trees have merged into Linus' tree, we
can remove the legacy hooks.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When stop device call netif_carrier_off() just after disabling TX queue to
avoid possibility of netdev watchdog warning and ->ndo_tx_timeout() invocation.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original patch from Stanislaw Gruszka <sgruszka@redhat.com>.
Using netif_carrier_off() is better than updating all the ->trans_start
on all the tx queues.
netif_carrier_off() needs to be called after bnx2_disable_int_sync()
to guarantee no race conditions with the serdes timers that can
modify the carrier state.
If the chip or phy is reset, carrier will turn back on when we get the
link interrupt. If there is no reset, we need to turn carrier back on
in bnx2_netif_start(). Again, the phy_lock prevents race conditions with
the serdes timers.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New firmware fixes a performance regression on small packets.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dump the correct MCP registers and add EMAC_RX_STATUS register during
NETDEV_WATCHDOG for debugging.
Signed-off-by: Eddie Wai <waie@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device state need to be mark as FAILED, if fail to start firmware.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing register defines which are not used by Qlgoic CNA device.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset/set DEV_UP bit during allocation and deallocation of resources.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>