mark this array as const because it is read-only
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mark the tables as const so that they end up in .rodata
section and don't cacheline share with things that get
written to.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
General cleanup on ir-usb module. Introduced
a common header that could be used also on
usb gadget framework.
Lot's of cleanups and now using macros from the header
file.
Signed-off-by: Felipe Balbi <me@felipebalbi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes some performance bugs observed with some workloads
when unlinking EHCI queue header (QH) descriptors from the async ring
(control/bulk schedule).
The mechanism intended to defer unlinking an empty QH (so there is no
penalty in common cases where it's quickly reused) was not working as
intended. Sometimes the unlink was scheduled:
- too quickly ... which can be a *strong* negative effect, since
that QH becomes unavailable for immediate re-use;
- too slowly ... wasting DMA cycles, usually a minor issue except
for increased bus contention and power usage;
Plus there was an extreme case of "too slowly": a logical error in the
IAA watchdog-timer conversion meant that sometimes the unlink never
got scheduled.
The fix replaces a simple counter with a timestamp derived from the
controller's 8 KHz microframe counter, and adjusts the timer usage
for some issues associated with HZ being less than 8K.
(Based on a patch originally by Alan Stern, and good troubleshooting
from Leonid.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Leonid <leonidv11@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We can't allow hubs on the 7th tier as they would allow
devices on the 8th tier.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we do rmmod ohci_hcd while an application is doing something, the
following may happen:
- a control URB completes (in finish_urb) and the ohci's endpoint is
set into ED_UNLINK in ed_deschedule
- same URB is (re)submitted because of the open/close loop or other
such application behaviour
- rmmod sets the state to HC_STATE_QUESCING
- finish_unlinks happens at next SOF; normally it would set ed into
ED_IDLE and immediately call ed_schedule (since URB had extra TDs
queued), which sets it into ED_OPER. But the check in ed_schedule
makes it fail with -EAGAIN (which is ignored)
- from now on we have a dead URB stuck; it cannot even be unlinked
because the ed status is not ED_OPER, and thus start_ed_unlink is
not invoked.
This patch removes the check. In 2.6.25, all callers check for
__ACTIVE bit before invoking ed_schedule, which is more appropriate.
Alan Stern and David Brownell approved of this (cautiously).
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As RMK pointed out, considering the fact that the _only_ platform with
a PXA and SA1111 is the Lubbock, and that SA1111 DMA doesn't work there,
(i.e. the SA1111 OHCI doesn't work there) the SA1111 OHCI driver should
really be made SA11x0 specific.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Looks like usb_put_hcd was missing. Also, make an always-zero function
return void.
Signed-off-by: Pete Zaitcev <zaitcev@yahoo.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i is used only as a for-loop index no need to declare another.
drivers/usb/atm/speedtch.c:832:7: warning: symbol 'i' shadows an earlier one
drivers/usb/atm/speedtch.c:766:6: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The get/set 2101_config helpers take an unsigned int rather than an
int. It is safe to change these in each case and may even produce
better code as it will be an unsigned divide rather than a signed
divide in places. All other manipulation was setting/masking bits
which will not be affected by the sign change.
Fixes the following sparse warnings:
drivers/usb/serial/cp2101.c:378:44: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:378:44: expected unsigned int *data
drivers/usb/serial/cp2101.c:378:44: got int *<noident>
drivers/usb/serial/cp2101.c:388:40: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:388:40: expected unsigned int *data
drivers/usb/serial/cp2101.c:388:40: got int *<noident>
drivers/usb/serial/cp2101.c:413:42: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:413:42: expected unsigned int *data
drivers/usb/serial/cp2101.c:413:42: got int *<noident>
drivers/usb/serial/cp2101.c:421:42: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:421:42: expected unsigned int *data
drivers/usb/serial/cp2101.c:421:42: got int *<noident>
drivers/usb/serial/cp2101.c:444:42: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:444:42: expected unsigned int *data
drivers/usb/serial/cp2101.c:444:42: got int *<noident>
drivers/usb/serial/cp2101.c:451:42: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:451:42: expected unsigned int *data
drivers/usb/serial/cp2101.c:451:42: got int *<noident>
drivers/usb/serial/cp2101.c:458:42: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:458:42: expected unsigned int *data
drivers/usb/serial/cp2101.c:458:42: got int *<noident>
drivers/usb/serial/cp2101.c:471:42: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:471:42: expected unsigned int *data
drivers/usb/serial/cp2101.c:471:42: got int *<noident>
drivers/usb/serial/cp2101.c:481:42: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:481:42: expected unsigned int *data
drivers/usb/serial/cp2101.c:481:42: got int *<noident>
drivers/usb/serial/cp2101.c:561:41: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:561:41: expected unsigned int *data
drivers/usb/serial/cp2101.c:561:41: got int *<noident>
drivers/usb/serial/cp2101.c:591:45: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:591:45: expected unsigned int *data
drivers/usb/serial/cp2101.c:591:45: got int *<noident>
drivers/usb/serial/cp2101.c:597:41: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:597:41: expected unsigned int *data
drivers/usb/serial/cp2101.c:597:41: got int *<noident>
drivers/usb/serial/cp2101.c:608:45: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:608:45: expected unsigned int *data
drivers/usb/serial/cp2101.c:608:45: got int *<noident>
drivers/usb/serial/cp2101.c:614:41: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:614:41: expected unsigned int *data
drivers/usb/serial/cp2101.c:614:41: got int *<noident>
drivers/usb/serial/cp2101.c:623:45: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:623:45: expected unsigned int *data
drivers/usb/serial/cp2101.c:623:45: got int *<noident>
drivers/usb/serial/cp2101.c:680:50: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:680:50: expected unsigned int *data
drivers/usb/serial/cp2101.c:680:50: got int *<noident>
drivers/usb/serial/cp2101.c:690:43: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:690:43: expected unsigned int *data
drivers/usb/serial/cp2101.c:690:43: got int *<noident>
drivers/usb/serial/cp2101.c:715:41: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:715:41: expected unsigned int *data
drivers/usb/serial/cp2101.c:715:41: got int *<noident>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is another case where the lock_kernel appears to be unneccessary and
could be removed with a bit more investigative work
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The BKL is actually probably not needed as the mutex seems sufficient. If
so then a further patch to drop it would be a good followup.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I'm pretty sure the mutex is sufficient for all locking but will come
back to that later if the USB folks don't beat me to it. For now get rid
of the old BKL ioctl method and wrap the ioctl handler
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I'm pretty sure this can be eliminated however I couldn't prove (or find)
what stopped the device vanishing mid IOCTL_GET_HARD_VERSION. Perhaps a
USB wizard could double check that and see if the lock_kernel can go
entirely.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ftdi has one ioctl, which is buggy and for debugging. Kill it off
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This keeps the gadget ioctl method wrapped but pushes the BKL down into
the gadget code so we can use unlocked_ioctl().
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Building on the previous patches which took code from this driver and
pakaged it in more-reusable network "function" components, this patch
gets rid of the original code and uses those components instead.
As seen with the other gadget driver conversions, the resulting code
is much easier to understand and (presumably) work with. In this case
that's especially true, since the Ethernet gadget had grown to handle
three (!) different Ethernet-over-USB protocols. This modularization
should make it much easier to add a fourth option for the newish CDC
"Ethernet Emulation Model" (or EEM).
Lightly tested, primarily at full speed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a simple example of a composite gadget, combining two
Communications Class Device (CDC) functions: ECM and ACM.
This provides a clear example of how the composite gadget framework
is intended to work. It's surprising that MS-Windows (or at least,
XP and previous) won't "just work" with something this simple...
One /proc/bus/usb/devices listing looks like:
T: Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 46 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=02(comm.) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0525 ProdID=a4aa Rev= 3.01
S: Manufacturer=Linux 2.6.26-rc6-pnut with net2280
S: Product=CDC Composite Gadget
C:* #Ifs= 4 Cfg#= 1 Atr=c0 MxPwr= 2mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
E: Ad=83(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=02 Prot=01 Driver=cdc_acm
E: Ad=86(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_acm
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Not all USB peripheral controller hardware can support this driver.
All the highspeed-capable peripheral controllers with drivers now in
the mainline kernel seem to support this, as does omap_udc. But
many full speed controllers don't have enough endpoints, or (as with
the PXA controllers) don't support altsettings.
Lightly tested.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a RNDIS function driver, extracted from the all-in-one
Ethernet gadget driver.
Lightly tested ... there seems to be a pre-existing problem when
talking to Windows XP SP2, not quite sure what's up with that yet.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a "CDC Ethernet" (ECM) function driver, extracted from the
all-in-one Ethernet gadget driver.
This is a good example of how to implement interface altsettings.
In fact it's currently the only such example in the gadget stack,
pending addition of OBEX support.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a simple "CDC Subset" (and MCCI "SAFE") function driver, extracted
from the all-in-one Ethernet gadget driver.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Abstract the peripheral side Ethernet-over-USB link layer code from
the all-in-one Ethernet gadget driver into a component that can be
called by various functions, so the various flavors can be split
apart and selectively reused.
A notable difference from the approach taken with the serial link
layer code (beyond talking to NET not TTY) is that because of the
initialization requirements, this only supports one network link.
(And one set of Ethernet link addresses.)
That is, each configuration may have only one instance of a network
function. This doesn't change behavior; the current code has that
same restriction. If you want multiple logical links, that can
easily be done using network layer tools.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some cleanup to the RNDIS code:
- Minor bugfix: rndis_unit() is supposed to put the link into the
RNDIS_UNINITIALIZED state, which does not mean "unused". There's
a separate method to stop using the link. (Bug doesn't affect
anything right now because of how the code is used.)
- Reduce coupling between RNDIS code and its user(s), in preparation
for updates in that code:
* Decouple RNDIS_RESPONSE_AVAILABLE notifications from net_device
by passing just a void* handle. (Also, remove the unused return
value of the notification callback.)
* When it needs a copy of net_device stats, just ask for it
- Remove unused/untested code backing various never-used OIDs:
* RNDIS_PM, RNDIS_WAKEUP ... "should" get implemented, but the
relevant docs were unclear, ambguous, and incomplete. Someone
with access to the Hidden Gospels (maybe in the EU?) might be
able to figure out what this should do.
* RNDIS_OPTIONAL_STATS ... as the name suggests, optional. Never
implemented in part because not all the semantics were clear.
* OID_GEN_RNDIS_CONFIG_PARAMETER, which has been #if 0 forever.
- A few small whitespace fixes
Plus switch the VERBOSE symbol over to the newer VERBOSE_DEBUG style.
There should be no functional changes because of this patch; it's a
net source code shrink (because of the dead/unused code removal) and
a small object code shrink (a couple hundred bytes on ARMv5).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This switches the serial gadget over to using the new "function"
versions of the serial port interfacing code. The remaining code
in the main source file is quite small...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Split out the generic serial support into a "function driver". This
closely mimics the ACM support, but with a MUCH simpler control model.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Split out CDC ACM parts of "gadget serial" to a "function driver".
Some key structural differences from the previous ACM support, shared
with with the generic serial function (next patch):
- As a function driver, it can be combined with other functions.
One gadget configuration could offer both serial and network
links, as an example.
- One serial port can be exposed in multiple configurations;
the /dev/ttyGS0 node could be exposed regardless of which
config the host selected.
- One configuration can expose multiple serial ports, such as
ttyGS0, ttyGS1, ttyGS2, and ttyGS3.
This code should be a lot easier to understand than the previous
all-in-one-big-file version of the driver.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update Gadget Zero to use the more modular versions of the loopback
and source/sink configuration drivers which build on the new gadget
framework code.
The core code is a LOT simpler, and it should be much easier now to
understand how the parts fit together. The conversion is an overall
source shrink in terms of this gadget, since it uses more midlayer
support. However, it's an overall increase in object size because
there's less sharing between the two configurations (improves code
clarity) and because the midlayer is a bit more functional than this
driver actually needs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This splits the gadget zero "loopback" configuration into a standalone
"configuration driver", building on the composite gadget framework code.
It doesn't yet pull the original code out of gadget zero or update how
that driver is built.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This splits the gadget zero "source/sink" configuration into a standalone
"configuration driver", building on the composite gadget framework code.
It doesn't yet pull the original code out of gadget zero or update how
that driver is built.
Neither this, nor its sibling "loopback" configuration, is a function
driver that can be combined with other functions. (The host "usbtest"
driver wouldn't know how to deal with that!) However the code becomes
simpler because of this conversion, so it's a net win.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add <linux/usb/composite.h> interfaces for composite gadget drivers, and
basic implementation support behind it:
- struct usb_function ... groups one or more interfaces into a function
managed as one unit within a configuration, to which it's added by
usb_add_function().
- struct usb_configuration ... groups one or more such functions into
a configuration managed as one unit by a driver, to which it's added
by usb_add_config(). These operate at either high or full/low speeds
and at a given bMaxPower.
- struct usb_composite_driver ... groups one or more such configurations
into a gadget driver, which may be registered or unregistered.
- struct usb_composite_dev ... a usb_composite_driver manages this; it
wraps the usb_gadget exposed by the controller driver.
This also includes some basic kerneldoc.
How to use it (the short version): provide a usb_composite_driver with a
bind() that calls usb_add_config() for each of the needed configurations.
The configurations in turn have bind() calls, which will usb_add_function()
for each function required. Each function's bind() allocates resources
needed to perform its tasks, like endpoints; sometimes configurations will
allocate resources too.
Separate patches will convert most gadget drivers to this infrastructure.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Define three new descriptor manipulation utilities, for use when
setting up functions that may have multiple instances:
usb_copy_descriptors() to copy a vector of descriptors
usb_free_descriptors() to free the copy
usb_find_endpoint() to find a copied version
These will be used as follows. Functions will continue to have static
tables of descriptors they update, now used as __initdata templates.
When a function creates a new instance, it patches those tables with
relevant interface and string IDs, plus endpoint assignments. Then it
copies those morphed descriptors, associates the copies with the new
function instance, and records the endpoint descriptors to use when
activating the endpoints. When initialization is done, only the copies
remain in memory. The copies are freed on driver removal.
This ensures that each instance has descriptors which hold the right
instance-specific data. Two instances in the same configuration will
obviously never share the same interface IDs or use the same endpoints.
Instances in different configurations won't do so either, which means
this is slightly less memory-efficient in some cases.
This also includes a bugfix to the epautoconf code that shows up with
this usage model. It must replace the previous endpoint number when
updating the template descriptors, not just mask in a few more bits.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Teach "gadget serial" to use the new abstracted (and bugfixed) TTY glue,
and remove all the orignal tangled-up code. Update the documentation
accordingly. This is a net object code shrink and cleanup; it should
make it a lot easier to see how the TTY glue should accomodate updates
to the TTY layer, be bugfixed, etc.
Notable behavior changes include: it can now support getty even when
there's no USB connection; it fits properly into the mdev/udev world;
and RX handling is better (throttling works, and low latency).
Configurations with scripts setting up the /dev/ttygserial device node
(with "experimental" major number) may want to change that to be a
symlink pointing to the /dev/ttyGS0 file, as a migration aid; else,
just switch entirely over to mdev/udev.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This abstracts the "gadget serial" driver TTY glue into a separate
component, cleaning it up and disentangling it from connection state.
It also changed some behaviors for the better:
- Stops using "experimental" major #127, and switches over to
having the TTY layer allocate the dev_t numbers.
- Provides /sys/class/tty/ttyGS* nodes, thus mdev/udev support.
(Note "mdev" hotplug bug in Busybox v1.7.2: /dev/ttyGS0 will
be a *block* device without CONFIG_SYSFS_DEPRECATED_V2.)
- The tty nodes no longer reject opens when there's no host.
Now they can support normal getty configs in /etc/inttab...
- Now implements RX throttling. When the line discipline says
it doesn't want any more data, only packets in flight will be
delivered (currently, max 1K/8K at full/high speeds) until it
unthrottles the data.
- Supports low_latency. This is a good policy for all USB serial
adapters, since it eliminates scheduler overhead on RX paths.
This also includes much cleanup including better comments, fixing
memory leaks and other bugs (including some locking fixes), messaging
cleanup, and an interface audit and tightening. This added up to a
significant object code shrinkage, on the order of 20% (!) depending
on CPU and compiler.
A separate patch actually kicks in this new code, using the functions
declared in this new header, and removes the previous glue.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It turns out newer versions of the AT91 UDC hardware have increased
sizes of some of the FIFOs. Reporting that is a Good Thing.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1092) implements "soft" unbinding for usb-storage. When
the disconnect routine is called, all commands and reset delays are
allowed to complete normally until after scsi_remove_host() returns.
This means that the commands needed for an orderly shutdown will be
sent through to the device.
Unlike before, the driver will now execute every command that it
accepts. Hence there's no need for special code to catch unexecuted
commands and fail them.
The new sequence of events when disconnect runs goes as follows:
If the device is truly unplugged, set the DISCONNECTING
flag so we won't try to access it any more.
If the SCSI-scanning thread hasn't started up yet, prevent
it from doing anything by setting the new DONT_SCAN flag.
Then wake it up and wait for it to terminate.
Remove the SCSI host. This unbinds the upper-level drivers,
doing an orderly shutdown. Commands sent to quiesce the
device will be transmitted normally, unless the device is
unplugged.
Set the DISCONNECTING flag so that we won't accept any new
commands that might get submitted (there aren't supposed to be
any) and we won't try to access the device for resets.
Tell the control thread to exit by waking it up with no
pending command, and wait for it to terminate.
Go on to do all the other normal stuff: releasing resources,
freeing memory, and so on.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1091) changes the way usbcore handles interface
unbinding. If the interface's driver supports "soft" unbinding (a new
flag in the driver structure) then in-flight URBs are not cancelled
and endpoints are not disabled. Instead the driver is allowed to
continue communicating with the device (although of course it should
stop before its disconnect routine returns).
The purpose of this change is to allow drivers to do a clean shutdown
when they get unbound from a device that is still plugged in. Killing
all the URBs and disabling the endpoints before calling the driver's
disconnect method doesn't give the driver any control over what
happens, and it can leave devices in indeterminate states. For
example, when usb-storage unbinds it doesn't want to stop while in the
middle of transmitting a SCSI command.
The soft_unbind flag is added because in the past, a number of drivers
have experienced problems related to ongoing I/O after their disconnect
routine returned. Hence "soft" unbinding is made available only to
drivers that claim to support it.
The patch also replaces "interface_to_usbdev(intf)" with "udev" in a
couple of places, a minor simplification.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes the following needlessly global functions static:
- enqueue_an_ATL_packet()
- enqueue_an_INT_packet()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1090) converts the one remaining semaphore in
usb-storage into a completion.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1089) separates out the dynamic atomic bitflags and the
static bitfields in usb-storage. Until now the two sorts of flags
have been sharing the same word; this has always been awkward.
To help prevent possible confusion, the two new fields each have a
different name from the original. us->fflags contains the fixed
bitfields (mostly taken from the USB ID table in unusual_devs.h), and
us->dflags contains the dynamic atomic bitflags (used with set_bit,
test_bit, and so on).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sort out the insane naming like "OperationalFirmwareVersion" which seems
designed to cause formatting problems and RSI
Merge various common code together
Clean up the pointlessly complex and spread about MCR handling
This is really just the low hanging fruit.
Needs lots of testing before it goes upstream so testers and reports
appreciated
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1083) combines hub_quiesce() and hub_stop() into a
single routine. There's no point keeping them separate since they are
usually called together.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1071) combines hub_activate() and hub_restart() into a
single routine. There's no point keeping them separate, since they
are always called together.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1082) makes a small optimization to the way the hub
driver carries out port debouncing immediately after a hub is
activated (i.e., initialized, reset, or resumed). If any port-change
statuses are observed, the code will delay for a minimal debounce
period -- thereby making a good start at debouncing all the ports at
once.
If this wasn't sufficient then khubd will debounce any port that still
requires attention. But in most cases it should suffice; it's rare
for a device to need more than a minimal debounce delay. (In the
cases of hub initialization or reset even that is most likely not
needed, since any devices plugged in at such times have probably been
attached for a while.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1073) adds to khubd a way to recover from power-session
interruption caused by transient connect-change or enable-change
events. After the debouncing period, khubd attempts to do a
USB-Persist-style reset or reset-resume. If it works, the connection
will remain unscathed.
The upshot is that we will be more immune to noise caused by EMI. The
grace period is on the order of 100 ms, so this won't permit recovery
from the "accidentally knocked the USB cable out of its socket" type
of event, but it's a start.
As an added bonus, if a device was suspended when the system goes to
sleep then we no longer need to check for power-session interruptions
when the system wakes up. Khubd will naturally see the status change
while processing the device's parent hub and will do the right thing.
The remote_wakeup() routine is changed; now it expects the caller to
acquire the device lock rather than acquiring the lock itself.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1081) straightens out the logic of the hub_restart()
routine. Each port of the hub is scanned and the driver makes sure
that ports which are supposed to be disabled really _are_ disabled.
Any ports with a significant change in status are flagged in
hub->change_bits, so that khubd can focus on them without the need to
scan all the ports a second time -- which means the hub->activating
flag is no longer needed.
Also, it is now recognized explicitly that the only reason for
resuming a port which was not suspended is to carry out a reset-resume
operation, which happens only in a non-CONFIG_USB_SUSPEND setting.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts Linus's previous patch that is in mainline to make it
easier for the USB hub.c patches that follow this to apply cleanly. The
functionality will be added back in a followon patch in this series.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1080) makes a significant change to the way khubd
handles port connect-change and enable-change events. Both types of
event are now debounced, and the debouncing is carried out _before_ an
existing usb_device is unregistered, instead of afterward.
This means that drivers will have to deal with longer runs of errors
when a device is unplugged, but they are supposed to be prepared for
that in any case.
The advantage is that when an enable-change occurs (caused for example
by electromagnetic interference), the debouncing period will provide
time for the cause of the problem to die away. A simple port reset
(added in a forthcoming patch) will then allow us to recover from the
fault.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1070) creates a new subroutine to check whether a device
can be resumed. This code is needed even when CONFIG_USB_SUSPEND
isn't set, because devices do suspend themselves when the root hub
(and hence the entire bus) is suspended, and power sessions can get
lost during a system sleep even without individual port suspends.
The patch also fixes a loose end in USB-Persist reset-resume handling.
When a low- or full-speed device is attached to an EHCI's companion
controller, the port handoff during resume will cause the companion
port's connect-status-change feature to be set. If that flag isn't
cleared, the port-reset code will think it indicates that the device
has been unplugged and the reset-resume will fail.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bus_id field is going away, use the dev_set_name() function
to set it properly.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bus_id field is going away, use the dev_name() function instead.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts Alan's previous patch so that the recent Hub changes will
apply cleanly. The above mentioned patch was needed for 2.6.26 to work
properly.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Lukas Hejtmanek <xhejtman@ics.muni.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This changes usb_create_hcd() to be able to handle the fact that
pci_name() has changed to a constant string.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6: (25 commits)
mmtimer: Push BKL down into the ioctl handler
[IA64] Remove experimental status of kdump
[IA64] Update ia64 mmr list for SGI uv
[IA64] Avoid overflowing ia64_cpu_to_sapicid in acpi_map_lsapic()
[IA64] adding parameter check to module_free()
[IA64] improper printk format in acpi-cpufreq
[IA64] pv_ops: move some functions in ivt.S to avoid lack of space.
[IA64] pvops: documentation on ia64/pv_ops
[IA64] pvops: add to hooks, pv_time_ops, for steal time accounting.
[IA64] pvops: add hooks, pv_irq_ops, to paravirtualized irq related operations.
[IA64] pvops: add hooks, pv_iosapic_ops, to paravirtualize iosapic.
[IA64] pvops: define initialization hooks, pv_init_ops, for paravirtualized environment.
[IA64] pvops: paravirtualize NR_IRQS
[IA64] pvops: paravirtualize entry.S
[IA64] pvops: paravirtualize ivt.S
[IA64] pvops: paravirtualize minstate.h.
[IA64] pvops: define paravirtualized instructions for native.
[IA64] pvops: preparation for paravirtulization of hand written assembly code.
[IA64] pvops: introduce pv_cpu_ops to paravirtualize privileged instructions.
[IA64] pvops: add an early setup hook for pv_ops.
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
netfilter: nf_conntrack_sctp: fix sparse warnings
netfilter: nf_nat_sip: c= is optional for session
netfilter: xt_TCPMSS: collapse tcpmss_reverse_mtu{4,6} into one function
netfilter: nfnetlink_log: send complete hardware header
netfilter: xt_time: fix time's time_mt()'s use of do_div()
netfilter: accounting rework: ct_extend + 64bit counters (v4)
netlink: add NLA_PUT_BE64 macro
netfilter: nf_nat_core: eliminate useless find_appropriate_src for IP_NAT_RANGE_PROTO_RANDOM
hdlcdrv: Fix CRC calculation.
Revert "pkt_sched: Make default qdisc nonshared-multiqueue safe."
net: In __netif_schedule() use WARN_ON instead of BUG_ON
net: Improve simple_tx_hash().
pkt_sched: Remove unused variable skb in dev_deactivate_queue function.
sunhme: Remove stop/wake TX queue calls in set-multicast-list handler.
ucc_geth: do not touch net queue in adjust_link phylib callback
gianfar: do not touch net queue in adjust_link phylib callback
atl1: Do not wake queue before queue has been started.
Fix kernel-doc comments so that they don't produce errors.
Also cut some extraneous copy-paste text.
Error(linhead//drivers/pci/pci.c:1133): duplicate section name 'Description'
Error(linhead//drivers/pci/pci.c:1189): duplicate section name 'Description'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'x86/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (160 commits)
x86: remove extra calling to get ext cpuid level
x86: use setup_clear_cpu_cap() when disabling the lapic
KVM: fix exception entry / build bug, on 64-bit
x86: add unknown_nmi_panic kernel parameter
x86, VisWS: turn into generic arch, eliminate leftover files
x86: add ->pre_time_init to x86_quirks
x86: extend and use x86_quirks to clean up NUMAQ code
x86: introduce x86_quirks
x86: improve debug printout: add target bootmem range in early_res_to_bootmem()
Subject: devmem, x86: fix rename of CONFIG_NONPROMISC_DEVMEM
x86: remove arch_get_ram_range
x86: Add a debugfs interface to dump PAT memtype
x86: Add a arch directory for x86 under debugfs
x86: i386: reduce boot fixmap space
i386/xen: add proper unwind annotations to xen_sysenter_target
x86: reduce force_mwait visibility
x86: reduce forbid_dac's visibility
x86: fix two modpost warnings
x86: check function status in EDD boot code
x86_64: ia32_signal.c: remove signal number conversion
...
* 'for-linus' of git://neil.brown.name/md: (52 commits)
md: Protect access to mddev->disks list using RCU
md: only count actual openers as access which prevent a 'stop'
md: linear: Make array_size sector-based and rename it to array_sectors.
md: Make mddev->array_size sector-based.
md: Make super_type->rdev_size_change() take sector-based sizes.
md: Fix check for overlapping devices.
md: Tidy up rdev_size_store a bit:
md: Remove some unused macros.
md: Turn rdev->sb_offset into a sector-based quantity.
md: Make calc_dev_sboffset() return a sector count.
md: Replace calc_dev_size() by calc_num_sectors().
md: Make update_size() take the number of sectors.
md: Better control of when do_md_stop is allowed to stop the array.
md: get_disk_info(): Don't convert between signed and unsigned and back.
md: Simplify restart_array().
md: alloc_disk_sb(): Return proper error value.
md: Simplify sb_equal().
md: Simplify uuid_equal().
md: sb_equal(): Fix misleading printk.
md: Fix a typo in the comment to cmd_match().
...
This is a trivial patch against the hdlcdrv module that fixes its CRC
calculation. The finished CRC was overwriting the first two bytes of
each packet rather than being appended to the end.
I've tested this with 2.6.8 and 2.6.10-rc1, but hdlcdrv hasn't changed
much recently so it should work with many other kernel versions.
Signed-off-by: Micah Dowty <micah@navi.cx>
Acked-by: Thomas Sailer <t.sailer@alumni.ethz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commits b02f5ad6a3 ("istallion: use
tty_port") and a352def21a ("tty: Ldisc
revamp") broke the istallion driver.
Fix the compile error and silence a warning.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Based upon a bug report by Alexander Beregalov and commentary
from Ben Hutchings.
These are totally unnecessary, in particular because this
driver's ->hard_start_xmit() handler takes the same driver
spinlock that the set-multicast-list handler uses.
Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon a bug report by Alexey Dobriyan, the patch is
also tested by him and confirmed to fix the problem.
Packet flow during link state events should not be done by
waking and stopping the TX queue anyways, that is handled
transparently by netif_carrier_{on,off}().
So, remove the netif_{wake,stop}_queue() calls in the link
check code, and add the necessary netif_start_queue() call
to atl1_up().
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements biovec merge function for crypt target.
If the underlying device has merge function defined, call it.
If not, keep precomputed value.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove max_sector restriction - merge function replaced it.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch implements biovec merge function for linear target.
If the underlying device has merge function defined, call it.
If not, keep precomputed value.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Introduce a bvec merge function for device mapper devices
for dynamic size restrictions.
This code ensures the requested biovec lies within a single
target and then calls a target-specific function to check
against any constraints imposed by underlying devices.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Change snapshot per-module mempool to per-device mempool.
Per-module mempools could cause a deadlock if multiple
snapshot devices are stacked above each other.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Fix a race condition that returns incorrect data when a write causes an
exception to be allocated whilst a read is still in flight.
The race condition happens as follows:
* A read to non-reallocated sector in the snapshot is submitted so that the
read is routed to the original device.
* A write to the original device is submitted. The write causes an exception
that reallocates the block. The write proceeds.
* The original read is dequeued and reads the wrong data.
This race can be triggered with CFQ scheduler and one thread writing and
multiple threads reading simultaneously.
(This patch relies upon the earlier dm-kcopyd-per-device.patch to avoid a
deadlock.)
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Whenever a snapshot read gets mapped through to the origin, track it in
a per-snapshot hash table indexed by chunk number, using memory allocated
from a new per-snapshot mempool.
We need to track these reads to avoid race conditions which will be fixed
by patches that follow.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Return a specific error message if there are an invalid number of multipath
arguments.
This invalid command returns an "Unknown error" because the ti->error field is
not set
dmsetup create --table '0 2 multipath 0 0 1 1 round-robin 0 1 1 /dev/sdh' mpath0
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
dm_dirty_log_{init,exit}() can now become static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Free path selector if the arguments are invalid.
This command (note that it is invalid) causes reference leak on module
"dm_round_robin" and prevents the module from being removed.
dmsetup create --table '0 2 multipath 0 0 1 1 round-robin /dev/sdh' mpath0
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
All modifications and most access to the mddev->disks list are made
under the reconfig_mutex lock. However there are three places where
the list is walked without any locking. If a reconfig happens at this
time, havoc (and oops) can ensue.
So use RCU to protect these accesses:
- wrap them in rcu_read_{,un}lock()
- use list_for_each_entry_rcu
- add to the list with list_add_rcu
- delete from the list with list_del_rcu
- delay the 'free' with call_rcu rather than schedule_work
Note that export_rdev did a list_del_init on this list. In almost all
cases the entry was not in the list anymore so it was a no-op and so
safe. It is no longer safe as after list_del_rcu we may not touch
the list_head.
An audit shows that export_rdev is called:
- after unbind_rdev_from_array, in which case the delete has
already been done,
- after bind_rdev_to_array fails, in which case the delete isn't needed.
- before the device has been put on a list at all (e.g. in
add_new_disk where reading the superblock fails).
- and in autorun devices after a failure when the device is on a
different list.
So remove the list_del_init call from export_rdev, and add it back
immediately before the called to export_rdev for that last case.
Note also that ->same_set is sometimes used for lists other than
mddev->list (e.g. candidates). In these cases rcu is not needed.
Signed-off-by: NeilBrown <neilb@suse.de>
Open isn't the only thing that increments ->active. e.g. reading
/proc/mdstat will increment it briefly. So to avoid false positives
in testing for concurrent access, introduce a new counter that counts
just the number of times the md device it open.
Signed-off-by: NeilBrown <neilb@suse.de>
This patch renames the array_size field of struct mddev_s to array_sectors
and converts all instances to use units of 512 byte sectors instead of 1k
blocks.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Also, change the type of the size parameter from unsigned long long to
sector_t and rename it to num_sectors.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
The checks in overlaps() expect all parameters either in block-based
or sector-based quantities. However, its single caller passes two
rdev->data_offset arguments as well as two rdev->size arguments, the
former being sector counts while the latter are measured in 1K blocks.
This could cause rdev_size_store() to accept an invalid size from user
space. Fix it by passing only sector-based quantities to overlaps().
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
- used strict_strtoull in place of simple_strtoull
- use my_mddev in place of rdev->mddev (they have the same value)
and more significantly,
- don't adjust mddev->size to fit, rather reject changes which make
rdev->size smaller than mddev->size
Adjusting mddev->size is a hangover from bind_rdev_to_array which
does a similar thing. But it really is a better design to insist that
mddev->size is set as required, then the rdev->sizes are set to allow
for that. The previous way invites confusion.
Signed-off-by: NeilBrown <neilb@suse.de>
* 'for-linus' of git://git.o-hand.com/linux-mfd:
mfd: let asic3 use mem resource instead of bus_shift
mfd: remove DS1WM register definitions from asic3.h
mfd: add ASIC3_CONFIG_GPIO templates
mfd: fix the asic3 irq demux code
mfd: asic3 should depend on gpiolib
mfd: fix asic3 config array initialisation
mfd: move asic3 probe functions into __init section
mfd: Use uppercase only for asic3 macros and defines
mfd: use dev_* macros for asic3 debugging
mfd: New asic3 gpio configuration code
mfd: asic3 children platform data removal
mfd: asic3 gpiolib support
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (1232 commits)
iucv: Fix bad merging.
net_sched: Add size table for qdiscs
net_sched: Add accessor function for packet length for qdiscs
net_sched: Add qdisc_enqueue wrapper
highmem: Export totalhigh_pages.
ipv6 mcast: Omit redundant address family checks in ip6_mc_source().
net: Use standard structures for generic socket address structures.
ipv6 netns: Make several "global" sysctl variables namespace aware.
netns: Use net_eq() to compare net-namespaces for optimization.
ipv6: remove unused macros from net/ipv6.h
ipv6: remove unused parameter from ip6_ra_control
tcp: fix kernel panic with listening_get_next
tcp: Remove redundant checks when setting eff_sacks
tcp: options clean up
tcp: Fix MD5 signatures for non-linear skbs
sctp: Update sctp global memory limit allocations.
sctp: remove unnecessary byteshifting, calculate directly in big-endian
sctp: Allow only 1 listening socket with SO_REUSEADDR
sctp: Do not leak memory on multiple listen() calls
sctp: Support ipv6only AF_INET6 sockets.
...
Looking at older kernel sources the APOLLO_ELPLUS option was added
somewhere during kernel 2.1, but even kernel 2.2.0 does not contain
any driver that would be enabled through it...
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Register the Atari-specific video modes with sysfs, so you can see them in
/sys/class/graphics/fb0/modes and change the video mode by writing to
/sys/class/graphics/fb0/mode.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Register the Amiga-specific video modes with sysfs, so you can see them in
/sys/class/graphics/fb0/modes and change the video mode by writing to
/sys/class/graphics/fb0/mode.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ZORRO: Replace deprecated __initcall with equivalent device_initcall.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to the tests in do_initcalls(), the proper error code in case no
device is found is -ENODEV, not -ENXIO or -EIO.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use net_device_stats from net_device structure instead of local.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'configfs-fixup-ptr-error' of git://oss.oracle.com/git/jlbec/linux-2.6:
configfs: Allow ->make_item() and ->make_group() to return detailed errors.
Revert "configfs: Allow ->make_item() and ->make_group() to return detailed errors."
commit d185705690 ("ACPI: don't walk
tables if ACPI was disabled") is another superfluous duplicate commit
caused by git -> quilt -> git conversion.
Revert it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit 816c2eda3c ("dock: bay: Don't call
acpi_walk_namespace() when ACPI is disabled.") was merged between
2.6.26-rc8 and -rc9)
Due to rebasing the ACPI tree via quilt the same patch got applied again
via commit cc7e51666d ("dock: bay: Don't
call acpi_walk_namespace() when ACPI is disabled.")
Revert it, as it is obviously bogus.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch cyclades to use the new tty_port structure
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reverse the order of one test and it gets much more readable
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch the synclink ports to use the new tty_port structure
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch the stallion driver to use the tty_port structure
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The tty pointer has been moved into a tty_port field, so we need to use
->info->port.tty instead of just ->info->tty. Fixes these build errors:
David Brownell <david-b@pacbell.net> wrote:
> drivers/serial/atmel_serial.c: In function 'atmel_rx_from_ring':
> drivers/serial/atmel_serial.c:665: error: 'struct uart_info' has no member named 'tty'
> drivers/serial/atmel_serial.c: In function 'atmel_rx_from_dma':
> drivers/serial/atmel_serial.c:672: error: 'struct uart_info' has no member named 'tty'
> drivers/serial/atmel_serial.c: In function 'atmel_startup':
> drivers/serial/atmel_serial.c:797: error: 'struct uart_info' has no member named 'tty'
> make[2]: *** [drivers/serial/atmel_serial.o] Error 1
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch the rocketport to use the new tty_port structure
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch istallion to use the new tty_port structure
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch isicom to use a tty_port structure for some fields
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Chris Malley posted a patch removing a NULL check in the riscom8 driver.
Further analysis shows that even more of the tests are irrelevant so we
can delete lots of stuff
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch riscom8 to use the new tty_port structure
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch drivers using the old "generic serial" driver to use the tty_port
structures
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch the EPCA driver to include and begin using a tty_port structure
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The below is the patch to replace blindly all possible places,
including Jack's fixes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
(Reviewed and checked rather than blindly added)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix compile errors in SGI console drivers caused by changes to the
tty_port structures in the linux-next tree.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Today's linux-next build (powerpc allyesconfig) failed like this:
drivers/serial/pmac_zilog.c: In function 'pmz_receive_chars':
drivers/serial/pmac_zilog.c:245: error: 'struct uart_info' has no member named 'tty'
drivers/serial/pmac_zilog.c:250: error: 'struct uart_info' has no member named 'tty'
I applied the patch below (which builds but may, or may not, be correct).
--
Cheers,
Stephen Rothwell sfr@canb.auug.org.auhttp://www.canb.auug.org.au/~sfr/
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Today's linux-next build (sparc64 defconfig) failed like this:
drivers/serial/sunhv.c: In function `receive_chars':
drivers/serial/sunhv.c:188: error: structure has no member named `tty'
drivers/serial/sunsu.c: In function `receive_chars':
drivers/serial/sunsu.c:314: error: structure has no member named `tty'
drivers/serial/sunsab.c: In function `receive_chars':
drivers/serial/sunsab.c:121: error: structure has no member named `tty'
I applied the following patch (which, again, may not be correct).
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch the serial_core based drivers to use the new tty_port structure.
We can't quite use all of it yet because of the dynamically allocated
extras in the serial_core layer.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Every tty driver has its own concept of a port structure and because
they all differ we cannot extract commonality. Begin fixing this by
creating a structure drivers can elect to use so that over time we can
push fields into this and create commonality and then introduce common
methods.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes CVS keywords that weren't updated for a long time in
comments, printk's and MODULE_DESCRIPTION's (no printk's or
MODULE_DESCRIPTION's are completely removed).
While doing this I also found and fixed a missing \n in a printk
in m32r_sio.c
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes ancient VCS tags (either protected
by #ifdef SCCS_LABELS or commented out).
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the line disciplines towards a conventional ->ops arrangement. For
the moment the actual 'tty_ldisc' struct in the tty is kept as part of
the tty struct but this can then be changed if it turns out that when it
all settles down we want to refcount ldiscs separately to the tty.
Pull the ldisc code out of /proc and put it with our ldisc code.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't forget to enable and disable PCI devices. The device might be
unusable without that.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Avoid dumping garbage to the serial port when the tty is flushed. This
tends to happen when rebooting from a serial console.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Serial drivers using DMA (like the atmel_serial driver) tend to get very
confused when the xmit buffer is flushed and nobody told them. They
also tend to spew a lot of garbage since the DMA engine keeps running
after the buffer is flushed and possibly refilled with unrelated data.
This patch adds a new flush_buffer operation to the uart_ops struct,
along with a call to it from uart_flush_buffer() right after the xmit
buffer has been cleared. The driver can implement this in order to
syncronize its internal DMA state with the xmit buffer when the buffer
is flushed.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The bus_shift parameter in platform_data is not needed
as we can tell the driver with the IOMEM_RESOURCE whether
the ASIC is located on a 16bit or 32bit memory bus.
The htc-egpio driver uses a more descriptive bus_width parameter,
but for drivers where the register map size fixed, we don't even
need this.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
