This is bad for two reasons:
1. If they're returned to outside applications, no-one knows what
they mean.
2. Eventually they'll clash with the ever expanding standard error
codes.
The problem error code in question is ETASK. I've replaced this by
ECOMM (communications error on send) a network error code that seems to
most closely relay what ETASK meant.
Acked-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
All SMP tasks sent through bsg generate messages like:
sas: smp_execute_task: task to dev 500605b000001450 response: 0x0 status 0x81
Three times (because the task gets retried). Firstly, don't retry
either overrun or underrun (the data buffer isn't going to change size)
and secondly, just report the underrun but don't set an error for it.
This is necessary so bsg can report back the residual.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This adds support for host side SMP processing, via a separate
SMP interpreter file.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Annotate sas_queuecommand with locking details, and clean up a few
more sparse warnings about static/non-static declarations.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
sparse complains about the mixing of enums in libsas. Since the
underlying numeric values of both enums are the same, combine them
to get rid of the warning.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The task_struct->pid member is going to be deprecated, so start
using the helpers (task_pid_nr/task_pid_vnr/task_pid_nr_ns) in
the kernel.
The first thing to start with is the pid, printed to dmesg - in
this case we may safely use task_pid_nr(). Besides, printks produce
more (much more) than a half of all the explicit pid usage.
[akpm@linux-foundation.org: git-drm went and changed lots of stuff]
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It was always set to ata_port_disable(). Removed the hook, and replaced
the very few ap->ops->port_disable() callsites with direct calls to
ata_port_disable().
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Introduce ata_link. It abstracts PHY and sits between ata_port and
ata_device. This new level of abstraction is necessary to support
SATA Port Multiplier, which basically adds a bunch of links (PHYs) to
a ATA host port. Fields related to command execution, spd_limit and
EH are per-link and thus moved to ata_link.
This patch only defines the host link. Multiple link handling will be
added later. Also, a lot of ap->link derefences are added but many of
them will be removed as each part is converted to deal directly with
ata_link instead of ata_port.
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If you have the libsas with ATA support, it needs libata to function.
The problem is that if you compile in libsas, you can't build libata
as a module (however, vice versa you can).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In sas_smp_get_phy_events() we never test if the call to
alloc_smp_req(RPEL_REQ_SIZE) succeeds or fails. That means we run
the risk of dereferencing a NULL pointer if it does fail. Far
better to test if we got NULL back and in that case return -ENOMEM
just as we already do for the other memory allocation in that
function.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Eliminate unnecessary PCI dependencies in libsas. It should use generic
DMA and struct device like other subsystems.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
sas_smp_handler crashes when smp utils are used with an aic94xx host
because certain devices (the sas_host itself, specifically) lack rphy
structures. No rphy means no SMP target support, but we shouldn't crash
here.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Not everyone wants libsas automatically to pull in libata. This patch
makes the behaviour configurable, so you can build libsas with or
without ATA support.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This fixes up the usage in libsas (which are easy to miss, since they're
only in the scsi-misc tree) ... and also corrects the documentation on
the point of what these two function pointers actually return.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Slab destructors were no longer supported after Christoph's
c59def9f22 change. They've been
BUGs for both slab and slub, and slob never supported them
either.
This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for SAS Management Protocol (SMP) passthrough
support via bsg. aic94xx can use this.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
lockdep noticed that with ATA support the port->dev_list_lock was
entangled at irq context, so it now needs to become IRQ safe
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This one was noticed by Gilbert Wu of Adaptec:
The libata core actually does the DMA mapping for you, so there has to
be an exception in the device drivers that *don't* do dma mapping for
ATA commands. However, since we've already done this, libsas must now
dma map any ATA commands that it wishes to issue ... and yes, this is a
horrible mess.
Additionally, the test in aic94xx for ATA protocols isn't quite right.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
ATA devices need special handling for sas_task_abort. If the ATA command
came from SCSI, then we merely need to tell SCSI to abort the scsi_cmnd.
However, internal commands require a bit more work--we need to fill the qc
with the appropriate error status and complete the command, and eventually
post_internal will issue the actual ABORT TASK.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The SATL should connect the scsi_cmnd to the sas_task (despite the presence
of libata) so that requests to abort scsi_cmnds headed to the ATA device
can be processed by the EH and aborted correctly. The abort status should
still be propagated from sas -> ata -> scsi.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When libsas encounters a STP device whose protocol isn't recognized (i.e.
not ATA or ATAPI), we should set the ata_device's class to ATA_DEV_UNKNOWN
instead of ATA_DEV_ATA.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A sas_task sent to an ATAPI devices returns SAM_GOOD if successful.
Therefore, we should treat this the same way we treat ATA commands
that succeed.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Since the aic94xx sequencer assigns its own NCQ tags to ATA commands, it
no longer makes any sense to copy the sactive field in the STP response
to ata_port->sactive, as that will confuse libata. Also, libata seems
to be capable of managing sactive on its own.
The attached patch gets rid of one of the causes of the BUG messages in
ata_qc_new, and seems to work without problems on an IBM x206m.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds a new field, lldd_task, to ata_queued_cmd so that libata
users such as libsas can associate some data with a qc. The particular
ambition with this patch is to associate a sas_task with a qc; that way,
if libata decides to timeout a command, we can come back (in
sas_ata_post_internal) and abort the sas task.
One question remains: Is it necessary to reset the phy on error, or will
the libata error handler take care of it? (Assuming that one is written,
of course.) This patch, as it is today, works well enough to clean
things up when an ATA device probe attempt fails halfway through the probe,
though I'm not sure this is always the right thing to do.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The sas_ata_qc_issue function was incorrectly written to return error
codes such as -ENOMEM. Since libata OR's qc->err_mask with the
return value, It is necessary to make my code return one of the
AC_ERR_ codes instead. For now, use AC_ERR_SYSTEM because an error
here means that the OS couldn't send the command to the controller.
If anybody has a suggestion for a better AC_ERR_ code to use, please
suggest it.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
ata_qc_complete and ata_sas_queuecmd require that the port lock be held
when they are called. sas_ata doesn't do this, leading to BUG messages
about qc tags newly allocated qc tags already being in use. This patch
fixes the locking, which should clean up the rest of those messages.
So far I've tested this against an IBM x206m with two SATA disks with no
BUG messages and no other signs of things going wrong, and the machine
finally passed the pounder stress test.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is a respin of my earlier patch that migrates the ATA support code
into a separate file. For now, the controversial linking bits have
been removed per James Bottomley's request for a patch that contains
only the migration diffs, which means that libsas continues to require
libata. I intend to address that problem in a separate patch.
This patch is against the aic94xx-sas-2.6 git tree, and it has been
sanity tested on my x206m with Seagate SATA and SAS disks without
uncovering any new problems.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We actually had two problems: the one with the tag (which is fixed by
zeroing the tag before sending the taskfile to the sequencer) but the
other with the fact that we sent our first NCQ command to the device
before the sequencer had been informed of the NCQ tagging
capabilities. I fixed the latter by moving the rphy_add() to the
correct point in the code after the NCQ capabilities are set up.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This replaces a few BUG_ON() statements with the correct failure error
handling. There are still many more to do.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It turns out this is fairly easy to plumb in by recognising the three
command types and copying the CDB. The protocol response path needs to
be amended to cope with SAS_PROTO_RESPONSE.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds SATAII NCQ support to libsas. Both the use_ncq and the
dma_xfer flags in ata_task must be set for NCQ to work correctly on the
Adaptec SAS controller. The rest of the patch adds ATA_FLAG_NCQ to
sata_port_info and sets up ap->scsi_host so that ata_setup_ncq doesn't
crash. Please note that this patch is against the aic94xx-sas git tree,
not scsi-misc. Thanks also to James Bottomley for providing an earlier
version of this patch from which to work.
I've tested this patch on a x206m with a ST380819AS SATA2 disk plugged
into the Adaptec SAS controller. The drive came up with a queue depth
of 31, and I successfully ran an I/O flood test to coerce libata into
sending multiple commands simultaneously. A kernel probe recorded the
maximum tag number that had been seen before and after the flood test;
before the test it was 2 and after it was 30, as I expected.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The prototype of this has changed for the link speed setting patch.
Need to update the SATA use of this.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds support for SATA over SAS expanders to the previous two
SATA support in libsas patches.
There were a couple of nasty non trivial things to sort out before this
one could be made to work.
Firstly, I'd like to thank Doug Gilbert for diagnosing a problem with
the LSI expanders where the REPORT_SATA_PHY command was returning the
D2H FIS in the wrong order (Although, here, I think I have to blame the
SAS standards which specifies the FIS "shall be returned in little
endian format" and later on "which means resp[24] shall be FIS type"
The latter, of course, implying big endian format). Just to make sure,
I put a check for the D2H FIS type being in the wrong position and
reverse the FIS data if it is.
The second is a problem outlined in Annex G of the SAS standard (again,
a technical point with D2H FIS ... necessitating a phy reset on certain
conditions).
With the patch, I can now see my SATA-1 disk in a cascaded expander
configuration.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Hook the scsi_host_template functions in libsas to delegate
functionality to libata when appropriate.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Misc code changes and merge fixes and update for libata->drivers/ata
move
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Currently, the freezer treats all tasks as freezable, except for the kernel
threads that explicitly set the PF_NOFREEZE flag for themselves. This
approach is problematic, since it requires every kernel thread to either
set PF_NOFREEZE explicitly, or call try_to_freeze(), even if it doesn't
care for the freezing of tasks at all.
It seems better to only require the kernel threads that want to or need to
be frozen to use some freezer-related code and to remove any
freezer-related code from the other (nonfreezable) kernel threads, which is
done in this patch.
The patch causes all kernel threads to be nonfreezable by default (ie. to
have PF_NOFREEZE set by default) and introduces the set_freezable()
function that should be called by the freezable kernel threads in order to
unset PF_NOFREEZE. It also makes all of the currently freezable kernel
threads call set_freezable(), so it shouldn't cause any (intentional)
change of behaviour to appear. Additionally, it updates documentation to
describe the freezing of tasks more accurately.
[akpm@linux-foundation.org: build fixes]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (166 commits)
[SCSI] ibmvscsi: convert to use the data buffer accessors
[SCSI] dc395x: convert to use the data buffer accessors
[SCSI] ncr53c8xx: convert to use the data buffer accessors
[SCSI] sym53c8xx: convert to use the data buffer accessors
[SCSI] ppa: coding police and printk levels
[SCSI] aic7xxx_old: remove redundant GFP_ATOMIC from kmalloc
[SCSI] i2o: remove redundant GFP_ATOMIC from kmalloc from device.c
[SCSI] remove the dead CYBERSTORMIII_SCSI option
[SCSI] don't build scsi_dma_{map,unmap} for !HAS_DMA
[SCSI] Clean up scsi_add_lun a bit
[SCSI] 53c700: Remove printk, which triggers because of low scsi clock on SNI RMs
[SCSI] sni_53c710: Cleanup
[SCSI] qla4xxx: Fix underrun/overrun conditions
[SCSI] megaraid_mbox: use mutex instead of semaphore
[SCSI] aacraid: add 51245, 51645 and 52245 adapters to documentation.
[SCSI] qla2xxx: update version to 8.02.00-k1.
[SCSI] qla2xxx: add support for NPIV
[SCSI] stex: use resid for xfer len information
[SCSI] Add Brownie 1200U3P to blacklist
[SCSI] scsi.c: convert to use the data buffer accessors
...
Well, first of all, I don't want to change so many files either.
What I do:
Adding a new parameter "struct bin_attribute *" in the
.read/.write methods for the sysfs binary attributes.
In fact, only the four lines change in fs/sysfs/bin.c and
include/linux/sysfs.h do the real work.
But I have to update all the files that use binary attributes
to make them compatible with the new .read and .write methods.
I'm not sure if I missed any. :(
Why I do this:
For a sysfs attribute, we can get a pointer pointing to the
struct attribute in the .show/.store method,
while we can't do this for the binary attributes.
I don't know why this is different, but this does make it not
so handy to use the binary attributes as the regular ones.
So I think this patch is reasonable. :)
Who benefits from it:
The patch that exposes ACPI tables in sysfs
requires such an improvement.
All the table binary attributes share the same .read method.
Parameter "struct bin_attribute *" is used to get
the table signature and instance number which are used to
distinguish different ACPI table binary attributes.
Without this parameter, we need to offer different .read methods
for different ACPI table binary attributes.
This is impossible as there are various ACPI tables on different
platforms, and we don't know what they are until they are loaded.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
sysfs is now completely out of driver/module lifetime game. After
deletion, a sysfs node doesn't access anything outside sysfs proper,
so there's no reason to hold onto the attribute owners. Note that
often the wrong modules were accounted for as owners leading to
accessing removed modules.
This patch kills now unnecessary attribute->owner. Note that with
this change, userland holding a sysfs node does not prevent the
backing module from being unloaded.
For more info regarding lifetime rule cleanup, please read the
following message.
http://article.gmane.org/gmane.linux.kernel/510293
(tweaked by Greg to not delete the field just yet, to make it easier to
merge things properly.)
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- convert to use the new accessors for the sg lists and the
parameters.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
I noticed that many source files include <linux/pci.h> while they do
not appear to need it. Here is an attempt to clean it all up.
In order to find all possibly affected files, I searched for all
files including <linux/pci.h> but without any other occurence of "pci"
or "PCI". I removed the include statement from all of these, then I
compiled an allmodconfig kernel on both i386 and x86_64 and fixed the
false positives manually.
My tests covered 66% of the affected files, so there could be false
positives remaining. Untested files are:
arch/alpha/kernel/err_common.c
arch/alpha/kernel/err_ev6.c
arch/alpha/kernel/err_ev7.c
arch/ia64/sn/kernel/huberror.c
arch/ia64/sn/kernel/xpnet.c
arch/m68knommu/kernel/dma.c
arch/mips/lib/iomap.c
arch/powerpc/platforms/pseries/ras.c
arch/ppc/8260_io/enet.c
arch/ppc/8260_io/fcc_enet.c
arch/ppc/8xx_io/enet.c
arch/ppc/syslib/ppc4xx_sgdma.c
arch/sh64/mach-cayman/iomap.c
arch/xtensa/kernel/xtensa_ksyms.c
arch/xtensa/platform-iss/setup.c
drivers/i2c/busses/i2c-at91.c
drivers/i2c/busses/i2c-mpc.c
drivers/media/video/saa711x.c
drivers/misc/hdpuftrs/hdpu_cpustate.c
drivers/misc/hdpuftrs/hdpu_nexus.c
drivers/net/au1000_eth.c
drivers/net/fec_8xx/fec_main.c
drivers/net/fec_8xx/fec_mii.c
drivers/net/fs_enet/fs_enet-main.c
drivers/net/fs_enet/mac-fcc.c
drivers/net/fs_enet/mac-fec.c
drivers/net/fs_enet/mac-scc.c
drivers/net/fs_enet/mii-bitbang.c
drivers/net/fs_enet/mii-fec.c
drivers/net/ibm_emac/ibm_emac_core.c
drivers/net/lasi_82596.c
drivers/parisc/hppb.c
drivers/sbus/sbus.c
drivers/video/g364fb.c
drivers/video/platinumfb.c
drivers/video/stifb.c
drivers/video/valkyriefb.c
include/asm-arm/arch-ixp4xx/dma.h
sound/oss/au1550_ac97.c
I would welcome test reports for these files. I am fine with removing
the untested files from the patch if the general opinion is that these
changes aren't safe. The tested part would still be nice to have.
Note that this patch depends on another header fixup patch I submitted
to LKML yesterday:
[PATCH] scatterlist.h needs types.h
http://lkml.org/lkml/2007/3/01/141
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After discussion with andmike and dougg, it seems that the purpose of
eh_device_reset_handler is to issue LU resets, and that
eh_bus_reset_handler would be a more appropriate place for a phy reset.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
libsas: Don't BUG when connecting two expanders via wide port
When a device is connected to an expander, the discovery process goes through
sas_ex_discover_dev to figure out what's attached to the phy. If it is the
case that the phy being discovered happens to be the second phy of a wide link
to an expander, that discover_dev function will incorrectly call
sas_ex_discover_expander, which creates another sas_port and tries to attach the
other sas_phys to the new port, thus triggering a BUG. The correct thing to do is
to check the other ex_phys of the expander to see if there's a sas_port for this
sas_phy, and attach the sas_phy to the existing sas_port.
This is easily triggered if one enables the phys of a wide port between
expanders one by one.
This second version of the patch fixes a small regression in the case where
all the phys show up at once and we accidentally try to attach to a port
that hasn't been created yet.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Set allow_restart=1 for all SAS disks so that they are spun up when needed.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch moves the code that handles SAS failures out of the main EH
function and into a separate function. It also detects commands that have
no sas_task (i.e. they completed, but with error data) and sends them into
scsi_error for processing. This allows us to handle SCSI errors (and
enables auto-spinup as a side effect) instead of dropping them on the
floor and falling into an infinite loop. It also requires the
implementation of a device reset function, which the SAS failure code has
been modified to employ for REQ_DEVICE_RESET.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
sas_rphy_delete does two things: it removes the sas_rphy from the transport
layer and frees the sas_rphy. This can be broken down into two functions,
sas_rphy_remove and sas_rphy_free; sas_rphy_remove is of interest to
sas_discover_root_expander because it calls functions that require
sas_rphy_add as a prerequisite and can fail (namely sas_discover_expander).
In that case, sas_discover_root_expander needs to be able to undo the effects
of sas_rphy_add yet leave the job of freeing the sas_rphy to the caller of
sas_discover_root_expander.
This patch also removes some unnecessary code from sas_discover_end_dev
to eliminate an unnecessary cycle of sas_notify_lldd_gone/found for SAS
devices, thus eliminating a sas_rphy_remove call (and fixing a race condition
where a SCSI target scan can come in between the gone and found call).
It also moves the sas_rphy_free calls into sas_discover_domain and
sas_ex_discover_end_dev to complement the sas_rphy_allocation via
sas_get_port_device.
This patch does not change the semantics of sas_rphy_delete.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Currently, sas_form_port checks the given asd_sas_phy's sas_phy to see if
there's already a port attached. If so, the SAS addresses of the port and
the phy are compared to determine if we need to detach from the port
because the addresses don't match or if we can stop; the SAS address stored
in the sas_port reflects whatever device _was_ attached to the port/phy, and
the SAS address stored in the sas_port reflects whatever device we just
discovered. As written, the code detaches from the port if the addresses
_do_ match, and prints an error if they do _not_ match. I believe this to
be incorrect, as it seems more logical to keep the port if the addresses
match (i.e. the phy was reset but the device didn't change), and detach it
they do not (i.e. the device changed).
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
James Bottomley