Must set filter selection as hardcoded coefficients for medium 3x3
filtering, which matches vbios setting for Ironlake.
This fixes display corrupt issue on HP arrandale with new vbios.
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
For new stepping of PCH, the display reference clock
is fully under driver's control. This one trys to setup
all needed reference clock for different outputs. Older
stepping of PCH chipset should be ignoring this.
This fixes output failure issue on newer PCH which requires
driver to take control of reference clock enabling.
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
To enable framebuffer compression on a g4x, we not only need the buffer
to tiled (X only), we also need to hold a fence register for the buffer.
Currently we only install a fence register for pre-i965s when setting up
the scanout buffer. Rather than adding some convoluted logic to
g4x_enable_fbc() to acquire a fence register, and perhaps to
g4x_disable_fbc() to release it again, we can extend the acquisition
during setup to all chipsets.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
FDI M/N calculation hasn't taken the current pipe color depth into account,
but always set as 24bpp. This one checks current pipe color depth setting,
and change FDI M/N calculation a little to use bits_per_pixel first, then
convert to bytes_per_pixel later.
This fixes display corrupt issue on Arrandle LVDS with 1600x900 panel
in 18bpp dual-channel mode.
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Until we figure out the right setting for powersave features on
Ironlake, disable it for now. Also disable watermark update,
which has new registers for it on Ironlake too.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[anholt: Resolved against the Pineview FBC changes]
Signed-off-by: Eric Anholt <eric@anholt.net>
According to the spec the LVDS_BORDER_ENABLE bit decides whether the border
data should be included in the active display and data sent to the panel.
Border should be used when in VGA centered (un-scaled) mode or when scaling
a 4:3 source image to a wide screen panel (typical 16:9).
So when the LVDS scaling is used, decide whether the LVDS_BORDER should be
enabled or not according to the current scaling mode.
At the same time fix the typo error in LVDS center scaling mode.
https://bugs.freedesktop.org/show_bug.cgi?id=23789
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
tested-by: Zhao Jian <jian.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: Initialize HDMI outputs as HDMI connectors, not DVI.
drm/i915: Multiply the refresh by 1000 in TV mode validatiion
drm/i915: Enable irq to trace batch buffer completion.
drm/i915: batch submit seqno off-by-one.
drm/i915: Record device minor rather than pointer in TRACE_EVENT
drm/i915: Don't call intel_update_fbc from intel_crtc_cursor_set
conflict in radeon since new init path merged with vga arb code.
Conflicts:
drivers/gpu/drm/radeon/radeon.h
drivers/gpu/drm/radeon/radeon_asic.h
drivers/gpu/drm/radeon/radeon_device.c
The previous patches had some unwanted side effects, I've fixed
the lack of 32bpp working, and fixed up 16bpp so it should also work.
this also adds the interface to allow the driver to set a preferred
console depth so for example low memory rn50 can set it to 8bpp.
It also catches 24bpp on cards that can't do it and forces 32bpp.
Tested on r100/r600/i945.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds support for the setcmap api and fixes the 8bpp
support at least on radeon hardware. It adds a new load_lut
hook which can be called once the color map is setup.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit 74dff282 exposed this unnecessary call by causing a change in
the failure path on i965 where framebuffer compression will be turned
on and off on every cursor update. If you don't have the xf86-video-intel
fix to avoid the blinking cursor effect, this is very slow.
Symptoms were a far more noticeable cursor blink with every cursor image
change combined with severe slowdown for animated cursors.
Signed-off-by: Brian Rogers <brian@xyzw.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel: (57 commits)
drm/i915: Handle ERESTARTSYS during page fault
drm/i915: Warn before mmaping a purgeable buffer.
drm/i915: Track purged state.
drm/i915: Remove eviction debug spam
drm/i915: Immediately discard any backing storage for uneeded objects
drm/i915: Do not mis-classify clean objects as purgeable
drm/i915: Whitespace correction for madv
drm/i915: BUG_ON page refleak during unbind
drm/i915: Search harder for a reusable object
drm/i915: Clean up evict from list.
drm/i915: Add tracepoints
drm/i915: framebuffer compression for GM45+
drm/i915: split display functions by chip type
drm/i915: Skip the sanity checks if the current relocation is valid
drm/i915: Check that the relocation points to within the target
drm/i915: correct FBC update when pipe base update occurs
drm/i915: blacklist Acer AspireOne lid status
ACPI: make ACPI button funcs no-ops if not built in
drm/i915: prevent FIFO calculation overflows on 32 bits with high dotclocks
drm/i915: intel_display.c handle latency variable efficiently
...
Fix up trivial conflicts in drivers/gpu/drm/i915/{i915_dma.c|i915_drv.h}
Add support for framebuffer compression on GM45 and above. Removes
some unnecessary I915_HAS_FBC checks as well (this is now part of the
FBC display function).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch splits out several of the display functions into a separate
display function table to avoid tons of chipset specific if..else
if..else if blocks all over. There are more opportunities for this
(some noted in the structure defintition); so more cleanup patches will
follow.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
VGA arb requires DRM support for non-kms drivers, to turn on/off
irqs when disabling the mem/io regions.
VGA arb requires KMS support for GPUs where we can turn off VGA
decoding. Currently we know how to do this for intel and radeon
kms drivers, which allows them to be removed from the arbiter.
This patch comes from Fedora rawhide kernel.
Signed-off-by: Dave Airlie <airlied@redhat.com>
We usually don't have an SAREA, and we always want to update the FBC
status anyway, so move the update up above the various master/sarea
checks.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
A very high dotclock (e.g. 229500kHz as reported by Anton) can cause
the entries_required variable to overflow, potentially leading to a
FIFO watermark value that's too low to support the given mode. Split
the division across the calculation to avoid this.
Cc: stable@kernel.org
Reported-by: Anton Khirnov <wyskas@gmail.com>
Tested-by: Anton Khirnov <wyskas@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
By handling latency variable efficiently we also get rid of this warning :
CC [M] drivers/gpu/drm/i915/intel_display.o
drivers/gpu/drm/i915/intel_display.c: In function ‘igd_enable_cxsr’:
drivers/gpu/drm/i915/intel_display.c:1918: warning: ‘latency’ may be used uninitialized in this function
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Due to a bogus FBC support check and failing to check for FBC support
in the right places, mode setting on non-mobile platforms could fail
and hang in the FBC disable routine. Fix it up.
This fix highlights the need for cleanups in this area (function
pointers and better feature support checks). Patches for that to
follow.
Tested-by: Kenny Graunke <kenny@whitecape.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Arrandale has new window based method for panel fitting.
This one enables full screen aspect scaling on LVDS. It fixes
standard mode display failure on LVDS for Arrandale.
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
New register for PCH LVDS on IGDNG should be used.
This is a copy-n-paste typo. This fixes possible dual
channel LVDS panel failure on IGDNG.
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch adds framebuffer compression (good for about ~0.5W power
savings in the best case) support for pre-GM45 chips. GM45+ have a new,
more flexible FBC scheme that will be added in a separate patch.
FBC can't always be enabled: the compressed buffer must be physically
contiguous and reside in stolen space. So if you have a large display
and a small amount of stolen memory, you may not be able to take
advantage of FBC. In some cases, a BIOS setting controls how much
stolen space is available. Increasing this to 8 or 16M can help.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Some laptop platforms will disable pipes and/or planes at lid close time
and not restore them when the lid is opened again. So catch the lid
event, and if the lid was opened, force a mode restore.
Fixes fdo bug #21230.
Acked-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
When the output device is LVDS, maybe the pixel clock of adjusted_mode will be
less than that in mode. In such case it will set the incorrect multipler factor
in DPLL_MD register.
So the dpll_md_reg will be reset when the output type is non-SDVO
https://bugs.freedesktop.org/show_bug.cgi?id=22761
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Reviewd-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
It seems that on IGDNG the same swizzling setup always applys.
And front buffer tiling needs to set address swizzle in display
arb control too.
Fix plane tricle feed setting in v1 which should be disable bit,
and always setup address swizzle to let hardware care for buffer
tiling in all cases.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
And clean up a small whitespace goof-up in the same function, while
I was looking at it.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
There are several sources of unnecessary power consumption on Intel
graphics systems. The first is the LVDS clock. TFTs don't suffer from
persistence issues like CRTs, and so we can reduce the LVDS refresh rate
when the screen is idle. It will be automatically upclocked when
userspace triggers graphical activity. Beyond that, we can enable memory
self refresh. This allows the memory to go into a lower power state when
the graphics are idle. Finally, we can drop some clocks on the gpu
itself. All of these things can be reenabled between frames when GPU
activity is triggered, and so there should be no user visible graphical
changes.
Signed-off-by: Jesse Barnes <jesse.barnes@intel.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Some i915/i945 platforms have a fairly high memory latency in certain
situations, so increase our constant a bit to avoid FIFO underruns.
The effect should be positive on other platforms as well; we'll have a
bit more insurance against a busy memory subsystem due to the extra
FIFO entries.
Fixes fdo bug #23368. Needed for 2.6.31.
Tested-by: Sven Arvidsson <sa@whiz.se>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Initially I always meant this code to be shared, but things
ran away from me before I got to it.
This refactors the i915 and radeon kms fbdev interaction layers
out into generic helpers + driver specific pieces.
It moves all the panic/sysrq enhancements to the core file,
and stores a linked list of kernel fbs. This could possibly be
improved to only store the fb which has fbcon on it for panics
etc.
radeon retains some specific codes used for a big endian
workaround.
changes:
fix oops in v1
fix freeing path for crtc_info
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Based on Bspec each encoder has different sharing pipe property,
i.e. Integrated or SDVO TV both will occupy one pipe exclusively,
and sdvo-non-tv and crt are allowed to share one. The patch moves
sharing judgment into differnet output functions, and sets the right
clone bit.
This fixes both HDMI outputs choosing the same pipe.
https://bugs.freedesktop.org/show_bug.cgi?id=22247
Signed-off-by: Ma Ling <ling.ma@intel.com>
Reviewed-by : Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
After the following commit is shipped, the SDVO C detection will depend on
the SDVO_C/DP detion bit.
commit 13520b051e
Author: Kristian Høgsberg <krh@redhat.com>
Date: Fri Mar 13 15:42:14 2009 -0400
drm/i915: Read the right SDVO register when detecting SVDO/HDMI.
According to the spec we should continue to detect the SDVO_B/C based on
the SDVO_B detection bit. The new detection bit on G4X platform is for
the HDMI_C detection rather than SDVO_C detection.
https://bugs.freedesktop.org/show_bug.cgi?id=20639
Signed-off-by: Ma Ling <ling.ma@intel.com>
Acked-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Commit 0c2e39525b is not sufficient to
get fd.o bug #20115 fixed.
In addition intel_find_best_PLL() must not only rely on BIOS settings
for i9xx chips but also for i8xx, so drop the IS_I9XX() check.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
http://bugs.freedesktop.org/show_bug.cgi?id=21417
Signed-off-by: Sean Young <sean@mess.org>
Reviewed-by: Zhao Yakui <yakui.zhao@intel.com>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This corresponds to a fix to UMS back in 2007. Fixes fd.o bug #20115.
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
I had one report of flicker due to FIFO underruns on 845G. Scott was
kind enough to test a few patches and report success with this one.
Looks like 845G measures FIFO size slightly differently than other
chips, and we were also clobbering the FIFO burst length. Fixing both
of those issues gives him a healthy machine again.
Note that we still only adjust plane A's watermark in the 830/845
case. If someone is willing to test we could support a bigger variety
of dual-head 830/845 configurations with a bit more code.
Fixes fdo bug #19304 (again).
Reported-by: Scott Hansen <scottandchrystie@comcast.net>
Tested-by: Scott Hansen <scottandchrystie@comcast.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
This adds embedded DisplayPort support on next mobile chip which
aims to replace origin LVDS port. VBT's driver feature block has
been used to determine the type of current internal panel for eDP
or LVDS.
Currently no panel fitting support for eDP and backlight control
would be added in future.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
During pipe DPMS off, instead of busy waiting pipe off, insert
delays during wait and don't loop after enough tries which matches
spec requirement. Also try to match DPMS on path by disable FDI TX
PLL in DPMS off. Disable PF by writing PF_WIN_SZ which really trigger
the update.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This does VGA disable like DDX driver. SR01 bit 5 should be set
before VGA plane disable through control register, otherwise we
might get random crash and lockups.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
If no planes are enabled, the self-refresh calculation may end up doing
a divide by zero. This patch should prevent that by making sure at
least one of the CRTCs had a valid hdisplay value.
Reported-by: Eric Anholt <eric@anholt.net>
Tested-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
If you're pushing a plane hard (i.e. you need most or all of the FIFO
entries just to cover your frame refresh latency), the watermark level
may end up being negative. So fix up the signed vs. unsigned math in
the calculation function to handle this correctly, giving all available
FIFO entries to such a configuration.
Reported-by: Eric Anholt <eric@anholt.net>
Tested-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
I discovered several bugs in the FIFO code that was recently applied.
Some of them fell into the "how did this ever work" category, since in
some cases we were using the wrong FIFO size values, and the
calculations ended up being way off.
This patch fixes all the bugs I found, and works well on my GM45, 915GM
and 855GM test machines; but as usual with these sorts of patches
broader testing is definitely requested (in particular this patch
affects 830, 845 and 865 for which I don't have test hardware).
Overall, the patch clarifies the watermark calculation function by
adding some comments and debug info, and making the variable names a
bit clearer. The "get FIFO size" portion of the code has also been
corrected, so we should be able to properly detect the FIFO allocations
for each pipe, for use in the watermark calculation.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
The 915 and 945 scanout engines can handle frame buffers up to 4096 pixels
wide. Pre-9xx hardware has an 8192 byte stride limit, and so we leave the
existing 2048 max in place.
I'm not sure why we limit the height to the same value; there's no intrinsic
hardware limit in the scanout engine.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Vbios will set lvds register correctly based on
current algorithm for lingle/dual Channel LVDS when
system boot, so we can accept this configuration
directly, regardless of LVDS enable status.
It fixed freedesktop.org bug #22262
Signed-off-by: Florian Mickler <florian@mickler.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
For some reason, the DP clocks were based off a 100MHz reference instead of
the standard 96MHz reference. This caused some DP monitors to fail to lock
to the signal.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Zhenyu Wang