Add the UART2 muxing data to the board file (this used to be,
erroneously, done in the bootloader).
Cc: stable <stable@vger.kernel.org> [3.7]
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The iterator correctly handles of_node_put() calls.
Remove it before continue'ing the loop.
Without this patch you get the following with
CONFIG_OF_DYNAMIC set:
ERROR: Bad of_node_put() on /ocp/timer@44e31000!
[<c001329c>] (unwind_backtrace+0x0/0xe0) from [<c03dd8f0>] (of_node_release+0x2c/0xa0)!
[<c03dd8f0>] (of_node_release+0x2c/0xa0) from [<c03ddea0>] (of_find_matching_node_and_match+0x78/0x90)!
[<c03ddea0>] (of_find_matching_node_and_match+0x78/0x90) from [<c06d349c>] (omap_get_timer_dt+0x78/0x90)!
[<c06d349c>] (omap_get_timer_dt+0x78/0x90) from [<c06d3664>] (omap_dm_timer_init_one.clone.2+0x34/0x2bc)!
[<c06d3664>] (omap_dm_timer_init_one.clone.2+0x34/0x2bc) from [<c06d3a2c>] (omap2_gptimer_clocksource_init.clone.4+0x24/0xa8)!
[<c06d3a2c>] (omap2_gptimer_clocksource_init.clone.4+0x24/0xa8) from [<c06cca58>] (time_init+0x20/0x30)!
[<c06cca58>] (time_init+0x20/0x30) from [<c06c9690>] (start_kernel+0x1a8/0x2fc)!
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Jon Hunter <jon-hunter@ti.com>
[tony@atomide.com: updated description per Jon]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise we will get:
WARNING: vmlinux.o(.text+0x1d4f0): Section mismatch in reference from the
function omap_init_ocp2scp() to the function .init.text:omap_device_build()
The function omap_init_ocp2scp() references
the function __init omap_device_build().
This is often because omap_init_ocp2scp lacks a __init
annotation or the annotation of omap_device_build is wrong.
Signed-off-by: Tony Lindgren <tony@atomide.com>
If some other kernel subsystem has a module notifier, and adds a kprobe
to a ftrace mcount point (now that kprobes work on ftrace points),
when the ftrace notifier runs it will fail and disable ftrace, as well
as kprobes that are attached to ftrace points.
Here's the error:
WARNING: at kernel/trace/ftrace.c:1618 ftrace_bug+0x239/0x280()
Hardware name: Bochs
Modules linked in: fat(+) stap_56d28a51b3fe546293ca0700b10bcb29__8059(F) nfsv4 auth_rpcgss nfs dns_resolver fscache xt_nat iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack lockd sunrpc ppdev parport_pc parport microcode virtio_net i2c_piix4 drm_kms_helper ttm drm i2c_core [last unloaded: bid_shared]
Pid: 8068, comm: modprobe Tainted: GF 3.7.0-0.rc8.git0.1.fc19.x86_64 #1
Call Trace:
[<ffffffff8105e70f>] warn_slowpath_common+0x7f/0xc0
[<ffffffff81134106>] ? __probe_kernel_read+0x46/0x70
[<ffffffffa0180000>] ? 0xffffffffa017ffff
[<ffffffffa0180000>] ? 0xffffffffa017ffff
[<ffffffff8105e76a>] warn_slowpath_null+0x1a/0x20
[<ffffffff810fd189>] ftrace_bug+0x239/0x280
[<ffffffff810fd626>] ftrace_process_locs+0x376/0x520
[<ffffffff810fefb7>] ftrace_module_notify+0x47/0x50
[<ffffffff8163912d>] notifier_call_chain+0x4d/0x70
[<ffffffff810882f8>] __blocking_notifier_call_chain+0x58/0x80
[<ffffffff81088336>] blocking_notifier_call_chain+0x16/0x20
[<ffffffff810c2a23>] sys_init_module+0x73/0x220
[<ffffffff8163d719>] system_call_fastpath+0x16/0x1b
---[ end trace 9ef46351e53bbf80 ]---
ftrace failed to modify [<ffffffffa0180000>] init_once+0x0/0x20 [fat]
actual: cc:bb:d2:4b:e1
A kprobe was added to the init_once() function in the fat module on load.
But this happened before ftrace could have touched the code. As ftrace
didn't run yet, the kprobe system had no idea it was a ftrace point and
simply added a breakpoint to the code (0xcc in the cc:bb:d2:4b:e1).
Then when ftrace went to modify the location from a call to mcount/fentry
into a nop, it didn't see a call op, but instead it saw the breakpoint op
and not knowing what to do with it, ftrace shut itself down.
The solution is to simply give the ftrace module notifier the max priority.
This should have been done regardless, as the core code ftrace modification
also happens very early on in boot up. This makes the module modification
closer to core modification.
Link: http://lkml.kernel.org/r/20130107140333.593683061@goodmis.org
Cc: stable@vger.kernel.org
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Reported-by: Frank Ch. Eigler <fche@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Basic test logs are available here:
http://www.pwsan.com/omap/testlogs/prcm_fixes_c_v3.8-rc/20130121073904/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=RtJt
-----END PGP SIGNATURE-----
Merge tag 'omap-fixes-b-for-v3.8-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.8-rc4/fixes
A few OMAP integration fixes for v3.8-rc, for OMAP4 audio and OMAP2 reboot.
Basic test logs are available here:
http://www.pwsan.com/omap/testlogs/prcm_fixes_c_v3.8-rc/20130121073904/
The init_completion() call does reinit not only the variable carrying
the flag that the completion finished, but also initialized the
waitqueue associated with the completion. On the contrary, the
INIT_COMPLETION() call only reinits the flag.
In case there was anything still stuck in the waitqueue, subsequent call
to init_completion() would be able to create possible race condition. This
patch uses the proper function and moves init_completion() into .probe() call
of the driver, to be issued only once.
Note that such scenario is impossible, since two threads can never enter the
mxs_i2c_xfer_msg(), since whole this section is protected by mutex in I2C core.
This by no means allows this issue to exit though.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
srcip_matches() previously had code like this:
srcip_matches(..., struct sockaddr *rhs) {
/* ... */
struct sockaddr_in6 *vaddr6 = (struct sockaddr_in6 *) &rhs;
return ipv6_addr_equal(..., &vaddr6->sin6_addr);
}
which interpreted the values on the stack after the 'rhs' pointer as an
ipv6 address. The correct thing to do is to use 'rhs', not '&rhs'.
Signed-off-by: Nickolai Zeldovich <nickolai@csail.mit.edu>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Pull drm fixes from Dave Airlie:
"A bunch of intel and radeon fixes, along with two fixes to TTM code.
The correct fix for the Intel ironlake failure is in this, and should
make things more stable, along with some misc radeon fixes."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
ttm: on move memory failure don't leave a node dangling
ttm: don't destroy old mm_node on memcpy failure
Revert "drm/radeon: do not move bo to different placement at each cs"
drm/i915: fix FORCEWAKE posting reads
drm/i915: Invalidate the relocation presumed_offsets along the slow path
drm/i915/eDP: do not write power sequence registers for ghost eDP
drm/radeon: improve semaphore debugging on lockup
drm/radeon: allow FP16 color clear registers on r500
drm/radeon: clear reset flags if engines are idle
drm/i915: Record DERRMR, FORCEWAKE and RING_CTL in error-state
Commit 1fb9341ac3 ("module: put modules in list much earlier") moved
some of the module initialization code around, and in the process
changed the exit paths too. But for the duplicate export symbol error
case the change made the ddebug_cleanup path jump to after the module
mutex unlock, even though it happens with the mutex held.
Rusty has some patches to split this function up into some helper
functions, hopefully the mess of complex goto targets will go away
eventually.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
if we have a move notify callback, when moving fails, we call move notify
the opposite way around, however this ends up with *mem containing the mm_node
from the bo, which means we double free it. This is a follow on to the previous
fix.
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When we are using memcpy to move objects around, and we fail to memcpy
due to lack of memory to populate or failure to finish the copy, we don't
want to destroy the mm_node that has been copied into old_copy.
While working on a new kms driver that uses memcpy, if I overallocated bo's
up to the memory limits, and eviction failed, then machine would oops soon
after due to having an active bo with an already freed drm_mm embedded in it,
freeing it a second time didn't end well.
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
More important fixes for 3.9:
- error_state improvements to help debug the new scanline wait code added
for gen6+ - bug reports started popping up :( patch from Chris Wilson.
- fix a panel power sequence confusion between the eDP and lvds detection
code resulting in black screens - regression introduce in 3.8 (Jani
Nikula)
- Chris fixed the root-cause of the ilk relocation vs. evict bug.
- Another piece of cargo-culted rc6 lore from Jani, fixes up a regression
where a system refused to go into rc6 after suspend sometimes.
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: fix FORCEWAKE posting reads
drm/i915: Invalidate the relocation presumed_offsets along the slow path
drm/i915/eDP: do not write power sequence registers for ghost eDP
drm/i915: Record DERRMR, FORCEWAKE and RING_CTL in error-state
A number of fixes, and one revert for a patch having some wierd side effects.
* 'drm-fixes-3.8' of git://people.freedesktop.org/~agd5f/linux:
Revert "drm/radeon: do not move bo to different placement at each cs"
drm/radeon: improve semaphore debugging on lockup
drm/radeon: allow FP16 color clear registers on r500
drm/radeon: clear reset flags if engines are idle
problem introduced recently by kvm id changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=SpOo
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module fixes and a virtio block fix from Rusty Russell:
"Various minor fixes, but a slightly more complex one to fix the
per-cpu overload problem introduced recently by kvm id changes."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
module: put modules in list much earlier.
module: add new state MODULE_STATE_UNFORMED.
module: prevent warning when finit_module a 0 sized file
virtio-blk: Don't free ida when disk is in use
Pull misc syscall fixes from Al Viro:
- compat syscall fixes (discussed back in December)
- a couple of "make life easier for sigaltstack stuff by reducing
inter-tree dependencies"
- fix up compiler/asmlinkage calling convention disagreement of
sys_clone()
- misc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
sys_clone() needs asmlinkage_protect
make sure that /linuxrc has std{in,out,err}
x32: fix sigtimedwait
x32: fix waitid()
switch compat_sys_wait4() and compat_sys_waitid() to COMPAT_SYSCALL_DEFINE
switch compat_sys_sigaltstack() to COMPAT_SYSCALL_DEFINE
CONFIG_GENERIC_SIGALTSTACK build breakage with asm-generic/syscalls.h
Ensure that kernel_init_freeable() is not inlined into non __init code
The ia64 function "thread_matches()" has no users since commit
e868a55c2a ("[IA64] remove find_thread_for_addr()"). Remove it.
This allows us to make ptrace_check_attach() static to kernel/ptrace.c,
which is good since we'll need to change the semantics of it and fix up
all the callers.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Operation-specific check (whether subvol is readonly or not) should go
after the mutual exclusiveness check.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
The error code that is returned in response to starting a mutually
exclusive operation when there is one already running got silently
changed from EINVAL to EINPROGRESS by 5ac00add. Returning EINPROGRESS
to, say, add_dev, when rm_dev is running is misleading. Furthermore,
the operation itself may want to use EINPROGRESS for other purposes.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Balance pause/resume logic got broken by 5ac00add (went in into 3.8-rc1
as part of dev-replace merge). Offending commit took a stab at making
mutually exclusive volume operations (add_dev, rm_dev, resize, balance,
replace_dev) not block behind volume_mutex if another such operation is
in progress and instead return an error right away. Balancing front-end
relied on the blocking behaviour, so the fix is ugly, but short of a
complete rework, it's the best we can do.
Reported-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Commit 8fb54284ba {ARM: mm: Add strongly ordered descriptor support}
added XN flag at section level but missed it at PTE level.
Fix it by adding the L_PTE_XN to MT_MEMORY_SO PTE descriptor.
Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Subhash Jadavani reported this partial backtrace:
Now consider this call stack from MMC block driver (this is on the ARMv7
based board):
[<c001b50c>] (v7_dma_inv_range+0x30/0x48) from [<c0017b8c>] (dma_cache_maint_page+0x1c4/0x24c)
[<c0017b8c>] (dma_cache_maint_page+0x1c4/0x24c) from [<c0017c28>] (___dma_page_cpu_to_dev+0x14/0x1c)
[<c0017c28>] (___dma_page_cpu_to_dev+0x14/0x1c) from [<c0017ff8>] (dma_map_sg+0x3c/0x114)
This is caused by incrementing the struct page pointer, and running off
the end of the sparsemem page array. Fix this by incrementing by pfn
instead, and convert the pfn to a struct page.
Cc: <stable@vger.kernel.org>
Suggested-by: James Bottomley <JBottomley@Parallels.com>
Tested-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The bit width check was introduced by 15afae60 (ACPI, APEI: Fix
incorrect APEI register bit width check and usage), and a fixup
for incorrect 32-bit width memory address was given by f712c71
(ACPI, APEI: Fixup common access width firmware bug). Now there
is a similar symptom:
[Firmware Bug]: APEI: Invalid bit width + offset in GAR [0x12345000/64/0/3/0]
Another bogus BIOS reports an incorrect 64-bit width in trigger table.
Thus, apply to a similar workaround for 64-bit width memory address.
Signed-off-by: Lans Zhang <jia.zhang@windriver.com>
Acked-by: Gary Hade <garyhade@us.ibm.com>
Acked-by: Myron Stowe <myron.stowe@redhat.com>
Acked-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
During the migration to the common clock framework, calls to the
functions omap2xxx_clkt_vps_late_init() were not preserved for
OMAP2420 and OMAP2430. This causes the variables "sys_ck_rate" and
"curr_prcm_set" to be uninitialised on boot. On reboot, this causes the
following error message to be displayed because the appropriate MPU
clock frequency (derived from sys_ck_rate) cannot be found.
"Could not set MPU rate to 4294MHz"
Fix this by adding back calls to omap2xxx_clkt_vps_late_init() in the
OMAP2420 and OMAP2430 clock initialisation code.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: dropped the duplicated call to
omap2xxx_clkt_vps_check_bootloader_rates() after consultation with Jon;
updated patch description]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
McPDM need to be configured to NO_IDLE mode when it is in used otherwise
vital clocks will be gated which results 'slow motion' audio playback.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[paul@pwsan.com: copy patch description into hwmod data comments]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
To avoid issues with audio caused by non locked ABE DPLL we should
make sure it is locked in all OMAP4 revisions.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: cleaned up patch description]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
acpi_processor_get_power_info() has to be called before
acpi_processor_setup_cpuidle_states() to have the latest
information available. This fixes the missing C-state information
after AC-->DC transition.
Signed-off-by: Thomas Schlichter <thomas.schlichter@web.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Here are 3 USB patches for 3.8-rc4. Two of them are new device id
patches, and the third fixes a reported oops in the io_ti USB serial
driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlD5o/cACgkQMUfUDdst+ym9xQCfcQOzPUnnU1EfJkHVeuSIdR8e
3hsAn26GuvNTIzqt392ML95dOLxAqe8Z
=iOum
-----END PGP SIGNATURE-----
Merge tag 'usb-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are 3 USB patches for 3.8-rc4. Two of them are new device id
patches, and the third fixes a reported oops in the io_ti USB serial
driver"
* tag 'usb-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: io_ti: Fix NULL dereference in chase_port()
USB: option: add TP-LINK HSUPA Modem MA180
USB: option: blacklist network interface on ONDA MT8205 4G LTE
Here are a few tty/serial driver fixes for 3.8-rc4 that resolve a number
of problems that people have been having, including the ptys ioctl issue
that is a regression fix.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlD5pb0ACgkQMUfUDdst+ykA7gCfUZJliBrTKxzm+hA1LoTC35/T
jCAAn04Xq7APwwWggS3fWGHpWLFwC0HT
=KT9T
-----END PGP SIGNATURE-----
Merge tag 'tty-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg Kroah-Hartman:
"Here are a few tty/serial driver fixes for 3.8-rc4 that resolve a
number of problems that people have been having, including the ptys
ioctl issue that is a regression fix"
* tag 'tty-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
8250/16?50: Add support for Broadcom TruManage redirected serial port
pty: return EINVAL for TIOCGPTN for BSD ptys
serial:ifx6x60:Keep word size accordance with SPI controller
tty: 8250_dw: Fix inverted arguments to serial_out in IRQ handler
serial: samsung: remove redundant setting of line config during port reset
serial:ifx6x60:Delete SPI timer when shut down port
tty/8250: The correct device id for this card is 0x0022
tty/8250: pbn_b0_8_1152000_200 is supposed to be an 8 port definition
tty: serial: vt8500: fix return value check in vt8500_serial_probe()
serial: mxs-auart: Index is unsigned
mxs: uart: fix setting RTS from software
Here are some bugfixes for the drivers/staging tree for 3.8-rc4.
Nothing major, just a number of small fixes for problems that people
have reported, including finally tracking down the root of the 64/32 bit
problem with the vt6656 that has been driving people crazy for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlD5pQkACgkQMUfUDdst+ylQjQCgkTxHcFHZLN9qNGgJctYPKIS8
JWgAnRRK4xVzRMJ1FuyoK/PJWJo7qmHC
=g3G7
-----END PGP SIGNATURE-----
Merge tag 'staging-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver bugfixes from Greg Kroah-Hartman:
"Here are some bugfixes for the drivers/staging tree for 3.8-rc4.
Nothing major, just a number of small fixes for problems that people
have reported, including finally tracking down the root of the 64/32
bit problem with the vt6656 that has been driving people crazy for a
while"
* tag 'staging-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging/sb105x: PARPORT config is not good enough must use PARPORT_PC
staging: wlan-ng: Fix clamping of returned SSID length
staging: vt6656: Fix inconsistent structure packing
staging:iio:adis16080: Perform sign extension
iio: mxs-lradc: indexes are unsigned
Here are two hyperv patches for 3.8-rc4 that fix some reported problems
hv_balloon driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlD5pHoACgkQMUfUDdst+ymd1gCdHXHjaNhqObMuWlmetwBijyuU
oEgAoNNbYkHnVxO7t7n18lB5ayWa33tO
=N848
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg Kroah-Hartman:
"Here are two hyperv patches for 3.8-rc4 that fix some reported
problems hv_balloon driver"
* tag 'char-misc-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Drivers: hv: balloon: Fix a memory leak
Drivers: hv: balloon: Fix a bug in the definition of struct dm_info_msg
- CVE-2013-0190/XSA-40 (or stack corruption for 32-bit PV kernels)
- Fix racy vma access spotted by Al Viro
- Fix mmap batch ioctl potentially resulting in large O(n) page allcations.
- Fix vcpu online/offline BUG:scheduling while atomic..
- Fix unbound buffer scanning for more than 32 vCPUs.
- Fix grant table being incorrectly initialized
- Fix incorrect check in pciback
- Allow privcmd in backend domains.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQEcBAABAgAGBQJQ+L7qAAoJEFjIrFwIi8fJLNIH/jUsneraEggWeh0L4GGWZvWL
cNCf0zjQt/pi1Q5drbleW2/6Wv6s6N1QA9pGRsJ+rrliC73HVTqIWFh0TjpwmCVy
hZal7jDXOuFVIR7GbGEPn004T6mkEnYDb/O2fyojwMVg0NQYwtMYJfTBkKdjKnmV
z6sWpQPVqO3/nZ17k2DipYRldbeiqS6LLOiUWd72b2W8bV4ySY5iVPVsqFusSEr6
PNyW33RPs5H0jEPR1uJlLD+l/uIbENykpEPeAS2uHGlch129+xHH5h79dwYJTbw6
x5nAOveO9VNJscUoqhpE7YbySzJmrUwxnBerZ6YTW6WCknYXrx4uiVAlfWem7uY=
=26Sq
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.8-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen fixes from Konrad Rzeszutek Wilk:
- CVE-2013-0190/XSA-40 (or stack corruption for 32-bit PV kernels)
- Fix racy vma access spotted by Al Viro
- Fix mmap batch ioctl potentially resulting in large O(n) page allcations.
- Fix vcpu online/offline BUG:scheduling while atomic..
- Fix unbound buffer scanning for more than 32 vCPUs.
- Fix grant table being incorrectly initialized
- Fix incorrect check in pciback
- Allow privcmd in backend domains.
Fix up whitespace conflict due to ugly merge resolution in Xen tree in
arch/arm/xen/enlighten.c
* tag 'stable/for-linus-3.8-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: Fix stack corruption in xen_failsafe_callback for 32bit PVOPS guests.
Revert "xen/smp: Fix CPU online/offline bug triggering a BUG: scheduling while atomic."
xen/gntdev: remove erronous use of copy_to_user
xen/gntdev: correctly unmap unlinked maps in mmu notifier
xen/gntdev: fix unsafe vma access
xen/privcmd: Fix mmap batch ioctl.
Xen: properly bound buffer access when parsing cpu/*/availability
xen/grant-table: correctly initialize grant table version 1
x86/xen : Fix the wrong check in pciback
xen/privcmd: Relax access control in privcmd_ioctl_mmap
Pull m68knommu arch fixes from Greg Ungerer:
"This contains a couple of fixes, both affecting compilation of non-mmu
m68k targets."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k: fix conditional use of init_pointer_table
m68knommu: add KMAP definitions for non-MMU definitions
Commit 816422ad76 ("asm-generic, mm: pgtable: consolidate zero page
helpers") broke the compile on MIPS if SPARSEMEM is enabled. We get
this:
In file included from arch/mips/include/asm/pgtable.h:552,
from include/linux/mm.h:44,
from arch/mips/kernel/asm-offsets.c:14:
include/asm-generic/pgtable.h: In function 'my_zero_pfn':
include/asm-generic/pgtable.h:466: error: implicit declaration of function 'page_to_section'
In file included from arch/mips/kernel/asm-offsets.c:14:
include/linux/mm.h: At top level:
include/linux/mm.h:738: error: conflicting types for 'page_to_section'
include/asm-generic/pgtable.h:466: note: previous implicit declaration of 'page_to_section' was here
Due header files inter-dependencies, the only way I see to fix it is
convert my_zero_pfn() for __HAVE_COLOR_ZERO_PAGE to macros.
Signed-off-by: Kirill A. Shutemov <kirill@shutemov.name>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: David Daney <david.daney@cavium.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andreas reports in https://bugzilla.kernel.org/show_bug.cgi?id=51741
that with his Gentoo config, acpi-cpufreq wasn't enabled and
powernow-k8 couldn't handoff properly to acpi-cpufreq leading to
running without P-state support (i.e., cores are constantly in P0).
To alleaviate that, we need to make powernow-k8 depend on acpi-cpufreq
so that acpi-cpufreq is always present.
References: https://bugzilla.kernel.org/show_bug.cgi?id=51741
Reported-by: Andreas <linuxuser330250@gmx.net>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: 3.7+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add missing braces around an if block in ffs_fs_parse_opts. This broke
parsing the uid/gid mount options and causes mount to fail when using
uid/gid. This has been introduced by commit b9b73f7c (userns: Convert usb
functionfs to use kuid/kgid where appropriate) in 3.7.
Cc: <stable@vger.kernel.org>
Signed-off-by: Benoit Goby <benoit@android.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
dwc3_gadget_set_ep_config expects maxburst as incremented by 1. So, by
default initialize ep->maxburst to 1 for ep0.
Cc: <stable@vger.kernel.org>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As we use platform_device_id for fsl-usb2-udc driver, it needs to
change clk connection-id, or the related devm_clk_get will be failed.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As mach/hardware.h is deleted, we can't visit platform code at driver.
It has no phy driver to combine with this controller, so it has to use
ioremap to map phy address as a workaround.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Luciano Coelho