This patch adds two new devices to the ftdi_sio driver's device ID
table. The device IDs were supplied by Stefan Nies of KOBIL Systems for
two of their devices using the FTDI chip.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch solves the following problem I've already discovered on the
latest 2.6.15-rc1-git1 kernel:
Nov 13 07:37:28 wrobel kernel: Bad page state at free_hot_cold_page (in process 'motion', page c164e020)
Nov 13 07:37:28 wrobel kernel: flags:0x40000400 mapping:00000000 mapcount:0 count:0
Nov 13 07:37:28 wrobel kernel: Backtrace:
Nov 13 07:37:28 wrobel kernel: [<c0146d86>] bad_page+0x85/0xbe
Nov 13 07:37:28 wrobel kernel: [<c0147629>] free_hot_cold_page+0x54/0x129
Nov 13 07:37:28 wrobel kernel: [<c01598c6>] __vunmap+0xa9/0xfe
Nov 13 07:37:28 wrobel kernel: [<c0154114>] vmalloc_to_page+0x34/0x55
Nov 13 07:37:28 wrobel kernel: [<c0159942>] vfree+0x27/0x35
Nov 13 07:37:28 wrobel kernel: [<f8a20292>] sn9c102_release_buffers+0x30/0x3f [sn9c102]
Nov 13 07:37:28 wrobel kernel: [<f8a231c2>] sn9c102_release+0x37/0xeb [sn9c102]
Nov 13 07:37:28 wrobel kernel: [<c0163e74>] __fput+0xa9/0x1aa
Nov 13 07:37:28 wrobel kernel: [<c01624f7>] filp_close+0x49/0x6d
Nov 13 07:37:30 wrobel kernel: [<c016258f>] sys_close+0x74/0x95
Nov 13 07:37:30 wrobel kernel: [<c0102ef9>] syscall_call+0x7/0xb
Nov 13 07:37:31 wrobel kernel: Trying to fix it up, but a reboot is needed
Signed-off-by: Damian Wrobel <dwrobel@ertel.com.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Per the PCI Express spec, the power-fault-detected bit in the
slot status register can be set anytime hardware detects a power
fault, regardless of whether the slot has a device populated in
it or not. This bit is sticky and must be explicitly cleared.
This patch is needed to allow hot-add after such a power fault
has been detected.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Trivial patch to report both hdaps axises to the joystick device, not
just the X axis.
Signed-off-by: Robert Love <rml@novell.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a bug where setting the low fan speed limits will not work if no
data was ever read through the sysfs interface and the fan clock
dividers have not been explicitely set yet either. The reason is that
data->fan_div[nr] may currently be used before it is initialized from
the chip register values. The fix is to explicitely initialize
data->fan_div[nr] before using it.
Bug reported, and fix tested, by Nicolas Mailhot.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the lm78 VID reading, which I accidentally broke while making
this driver use the common vid_from_reg function rather than
reimplementing its own in 2.6.14-rc1.
I'm not proud of it, trust me.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add SENSORS_LIMIT in store VCore limit functions. This fixes a potential
u8 overflow on out-of-range user input.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch (as603) makes a few small fixes to the driver core:
Change spin_lock_irq for a klist lock to spin_lock;
Fix reference count leaks;
Minor spelling and formatting changes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by Patrick Mochel <mochel@digitalimplant.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fix causes problems on the very first floppy access - we haven't yet
talked to the FDC so we don't know which state the write-protect tab is in.
Revert for now.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We memset the structure across opens except for the flags. The correct
fix is more intrusive but this should fix a problem with bad iounmaps
seen on AGP radeons acting like PCI ones.
Signed-off-by: Dave Airlie <airlied@linux.ie>
The DRM only uses drm_alloc_pages for non-SG PCI cards using DRM.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
PCI->PCI bridge, then bus->self is allowed to be NULL. Certainly that's
the case on my Pegasos, and it makes the MGA DRM driver oops...
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
The spinlock region_lock is held while calling mark_region which can sleep.
Drop the spinlock before calling that function.
A region's state and inclusion in the clean list are altered by rh_inc and
rh_dec. The state variable is set to RH_CLEAN in rh_dec, but only if
'pending' is zero. It is set to RH_DIRTY in rh_inc, but not if it is already
so. The changes to 'pending', the state, and the region's inclusion in the
clean list need to be atomicly.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
bio_list_merge() should do nothing if the second list is empty - not oops.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
do_end_io() can be called without interrupts blocked.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The linux bitset operators (test_bit, set_bit etc) work on arrays of "unsigned
long". dm-log uses such bitsets but treats them as arrays of uint32_t, only
allocating and zeroing a multiple of 4 bytes (as 'clean_bits' is a uint32_t).
The patch below fixes this problem.
The problem is specific to 64-bit big endian machines such as s390x or ppc-64
and can prevent pvmove terminating.
In the simplest case, if "region_count" were (say) 30, then
bitset_size (below) would be 4 and bitset_uint32_count would be 1.
Thus the memory for this butset, after allocation and zeroing would
be
0 0 0 0 X X X X
On a bigendian 64bit machine, bit 0 for this bitset is in the 8th
byte! (and every bit that dm-log would use would be in the X area).
0 0 0 0 X X X X
^
here
which hasn't been cleared properly.
As the dm-raid1 code only syncs and counts regions which have a 0 in the
'sync_bits' bitset, and only finishes when it has counted high enough, a large
number of 1's among those 'X's will cause the sync to not complete.
It is worth noting that the code uses the same bitsets for in-memory and
on-disk logs. As these bitsets are host-endian and host-sized, this means
that they cannot safely be moved between computers with
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In some circumstances the LIST_VERSIONS output is truncated because the size
calculation forgets about a 'uint32_t' in each structure - but the inclusion
of the whole of ALIGN_MASK frequently compensates for the omission.
This is a quick workaround to use an upper bound. (The code ought to be fixed
to supply the actual size.)
Running 'dmsetup targets' may demonstrate the problem: when I run it, the last
line comes out as 'erro' instead of 'error'. Consequently, 'lvcreate --type
error' doesn't work.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
An error path in table_load() forgets to release a table that won't now be
referenced.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This driver only appears on IA32 & EM64T boxes.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
scsi_get_command() attempts to write into a structure that may not have
been successfully allocated. Move this write inside the if statement that
ensures we won't panic the kernel with a NULL pointer dereference.
Signed-off-by: Matthew Dobson <colpatch@us.ibm.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/cpufreq/cpufreq.c: In function `cpufreq_remove_dev':
drivers/cpufreq/cpufreq.c:696: warning: unused variable `cpu_sys_dev'
Signed-off-by: Grant Coady <gcoady@gmail.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reported by: Wayne E. Harlan
"[1.] One line summary of the problem:
When the kernel option "vga=1" is used, additional tty's (alt+control+Fx
with x=2,3,4,5, etc) do not provide the full 50 lines of output. The first
one does have 50 lines, however.
[2.] Full description of the problem/report:
These addtitional tty's show only 39 lines plus the top pixel of the 40-th
line. The remaining lines are black and not shown. Kernel version
2.6.13.4 does not show this problem."
This bug is caused by using a stale font height value on vgacon_init.
Booting with vga=1 gives an 80x50 screen with an 8x8 font. Somewhere
during the initialization, the font was changed to 8x9 and the first
vc was correctly resized to 80x44. However, the rest of the vc's were
not allocated yet, and when they were subsequently initialized, they
still used a font height of 8 (instead of 9) causing the mentioned bug.
Fix by saving the new font height to vga_video_font_height.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The shift value (amount to shift the bitmap so first pixel starts at
origin(0,0)) is incorrect. This causes corrupted characters or a kernel crash
if fontwidth is not divisible by 8 at 270 degrees, or fontheight not divisible
by 8 at 180 degrees.
Report and part of the fix contributed by Knut Petersen.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's strange enough to be looking out for anonymous pages in VM_UNPAGED areas,
let's not insert the ZERO_PAGE there - though whether it would matter will
depend on what we decide about ZERO_PAGE refcounting.
But whereas do_anonymous_page may (exceptionally) be called on a VM_UNPAGED
area, do_no_page should never be: just BUG_ON.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/net/dgrs.c: In function `dgrs_init_module':
drivers/net/dgrs.c:1598: `dgrs_pci_driver' undeclared (first use in this function)
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix an OOPS is CinergyT2 driver when registering IR remote
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
kseriod and kgameportd used to process all pending events before
checking for freeze condition. This may cause swsusp to time out
while stopping tasks when resuming. Switch to process events one
by one to check freeze status more often.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
If thread that submitted FF request gets interrupted somehow it
will release request structure and ioctl handler will work with
freed memory. TO prevent that from happening switch to using
wait_for_completion instead of wait_for_completion_interruptible.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Try to save battery power by disabling wifi and bluetooth on suspend.
Signed-off-by: Miloslav Trmac <mitr@volny.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Also fix a potential issue with some notebooks:
The current code assumes the response to bios_wifi_get_default_setting is
either 1 (disabled) or 3 (enabled), or wifi isn't supported. The BIOS
response appears to be a bit field w/ 0x1 indicating hardware presence, 0x2
indicating actiation status, and the other 6 bits being unknown/reserved --
with the patch, these 6 bits are ignored.
Signed-off-by: Bernhard Rosenkraenzer <bero@arklinux.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
On x86_64:
{standard input}:233: Error: suffix or operands invalid for `push'
{standard input}:233: Error: suffix or operands invalid for `pop'
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
A driver for laptop buttons using an x86 BIOS interface that is
apparently used on quite a few laptops and seems to be originating
from Wistron.
This driver currently "knows" only about Fujitsu-Siemens Amilo Pro V2000
(i.e. it can detect the laptop using DMI and it contains the
keycode->key meaning mapping for this laptop) and Xeron SonicPro X 155G
(probably can't be reliably autodetected, requires a module parameter),
adding other laptops should be easy.
In addition to reporting button presses to the input layer the driver
also allows enabling/disabling the embedded wireless NIC (using the
"Wifi" button); this is done using the same BIOS interface, so it seems
only logical to keep the implementation together. Any flexibility
possibly gained by allowing users to remap the function of the "Wifi"
button is IMHO not worth it when weighted against the necessity to run
an user-space daemon to convert button presses to wifi state changes.
Signed-off-by: Miloslav Trmac <mitr@volny.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Changing led state is pretty slow operation; when there are multiple
requests coming at a high rate they may interfere with normal typing.
Try optimize (skip) changing hardware state when multiple requests
are coming back-to-back.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
flagged_taskfile() is called from execute_drive_cmd()
(the only user) only if args->tf_out_flags.all != 0.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since the spinlock was removed from sa1100_start_tx(), the "flags"
variable becomes redundant. Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The receiver status register reports latched error conditions, which
must be cleared by writing to it. However, the data register reports
unlatched conditions which are associated with the current character.
Use the data register to interpret error status rather than the RSR.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make sure that userspace passes in enough data when sending a MAD. We
always copy at least sizeof (struct ib_user_mad) + IB_MGMT_RMPP_HDR
bytes from userspace, so anything less is definitely invalid. Also,
if the length is less than this limit, it's possible for the second
copy_from_user() to get a negative length and trigger a BUG().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The following patch fixes a crash caused by attempting to bounce buffer
when an IDE CD-ROM is used on a machine with an IO-MMU. [At least, this
patch fixes things so I can use my IDE CD-ROM behind an ns87415 on a
HP PA-RISC workstation.]
Signed-off-by: James Bottomley <jejb@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Calculation of QP capabilities still isn't exactly right in mthca:
max_send_sge/max_recv_sge fields returned in create_qp can exceed the
handware supported limits.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
From: Amit Gud <amitg@calsoftinc.com>
Patch follows from the suggestions by AC and Felipe W Damasio for fixing the
return codes from IDE drivers.
[ bart: fix coding style while at it ]
Signed-off-by: Amit Gud <gud@eth.net>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fixes an oops in sbp2util_find_command_for_SCpnt after sbp2scsi_abort:
https://bugzilla.novell.com/show_bug.cgi?id=113734
Signed-off-by: Jody McIntyre <scjody@steamballoon.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
(cherry picked from 7945619794 commit)
From: Thibaut VARENE <T-Bone@parisc-linux.org>
Cleaning up the hwif without knowing its previous state in pmac.c is a big
and potentially dangerous job, and there seems to be no generic code interface
that would provide either a way to properly release an hwif or to clean it up.
Fixes OOPS for empty PMAC interface and add-on PCI controller.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
These drivers do not compile on big endian systems, and parisc
is big endian. Also mark some as broken on m68k as well.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
From: Hanna Linder <hannal@us.ibm.com>
The dev returned from pci_find_device() was not used so it can be
replaced with pci_dev_present(). Compile tested.
Signed-off-by: Hanna Linder <hannal@us.ibm.com>
Signed-off-by: Maximilian Attems <janitor@sternwelten.at>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Mention PA-RISC in NS87415 help. PA-RISC [BCJ]xxx0 workstations come with
NS87415 integrated for their CD-ROM drives.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Depend on GSC, not PARISC. Machines without GSC don't have a MUX.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
The structure ide_driver_t have a .owner field which is a duplicate
of .gendriver.owner field (.gen_driver is a struct device_driver).
This patch removes ide_driver_t's owner field.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Support multiple controllers in the via82cxxx IDE driver.
Cable detection and ISA bridge finding have been moved into
their own functions.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This entry adds needless complication to the driver as it requires the use of
global variables to be passed into via_get_info(), making things quite ugly
when we try and make this driver support multiple controllers simultaneously.
This patch removes /proc/via for simplicity.
On 10/13/05, Daniel Drake <dsd@gentoo.org> wrote:
> Per Bart's suggestion, I've created a user-space app which shows identical
> data (and doesn't even rely on the via82cxxx IDE driver).
>
> http://www.reactivated.net/software/viaideinfo/
>
> So, I think we should be clear to drop /proc/ide/via now.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Jeff Garzik pointed me to his code to see how to remove a disk from
the system _properly_. Well, here it is...
Every place we remove disks we are now testing before calling del_gendisk
or blk_cleanup_queue and then call put_disk.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
Applications using CCISS_BIG_PASSTHRU complained that the data written
was zeros. The problem is that the buffer is being cleared after the
user copy, unless the user copy has failed... Correct that logic.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
ipw2100: Fix 'Driver using old /proc/net/wireless...' message
Wireless extensions moved the get_wireless_stats handler from being
in net_device into wireless_handler.
A prior instance of this patch resolved the issue for the ipw2200.
This one fixes it for the ipw2100.
Signed-off-by: Benoit Boissinot <benoit.boissinot@ens-lyon.org>
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change CONFIG_FEC_8XX to depend on CONFIG_8xx instead of CONFIG_FEC.
CONFIG_FEC depends on ColdFire CPUs, which does not apply for the
PPC 8xx processors.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hermas_bap_pread, hermes_bap_pwrite, and hermes_bap_pwrite_pad all have a parameter "len" that is declared unsigned,
but checked for a value less than zero. Auditing the callers, it is possible for len to be passed a negative value, so len should be an int.
Thanks to LinuxICC (http://linuxicc.sf.net)
Signed-off-by: Gabriel A. Devenyi <ace@staticwave.ca>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
In isl_38xx.c
In routine isl38xx_trigger-device
Move unnecessary udelay/register read.
This is only required when hand-compiling the driver and
setting VERBOSE > SHOW_ERROR_MESSAGES
Signed-off-by: Roger While <simrw@sim-basis.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This header file patch was missing from the recent SAA9730 patch.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
For the four versions of hardware that we (currently) support microcode
download on, the default configuration of our receive interrupt mitigation
microcode was too aggressive, and caused unnecessary delays when pinging,
and low(er) throughput on single connection latency sensitive performance
tests.
This code adds microcode support, and sets the defaults to more reasonable
settings. It also explains the functionality in the code in more detail.
Compile and load tested, shows expected behavior for slight delay of ping
packets (1-2ms) when ucode is loaded, and decent interrupt moderation for
small packets, while maintaining good throughput.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
sil24_error_intr logs all error interrupts. ATAPI devices generates
many harmless errors which can be ignored and all serious ones are
reported via sense data by SCSI layer. Don't log device errors from
ATAPI devices.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch implements ATAPI support for sil24 and bumps driver version
to 0.23.
Signed-off-by: Tejun Heo <htejun@gmail.com>
--
Jeff, it has been converted to use ->dev_config as pointed out.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
