Introduce a replacement for the in-kernel portmapper client that supports
all 3 versions of the rpcbind protocol. This code is not used yet.
Original code by Groupe Bull updated for the latest kernel, with multiple
bug fixes.
Note that rpcb_clnt.c does not yet support registering via versions 3 and
4 of the rpcbind protocol. That is planned for a later patch.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Currently rpc_malloc sets req->rq_buffer internally. Make this a more
generic interface: return a pointer to the new buffer (or NULL) and
make the caller set req->rq_buffer and req->rq_bufsize. This looks much
more like kmalloc and eliminates the side effects.
To fix a potential deadlock, this patch also replaces GFP_NOFS with
GFP_NOWAIT in rpc_malloc. This prevents async RPCs from sleeping outside
the RPC's task scheduler while allocating their buffer.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The RPC buffer size estimation logic in net/sunrpc/clnt.c always
significantly overestimates the requirements for the buffer size.
A little instrumentation demonstrated that in fact rpc_malloc was never
allocating the buffer from the mempool, but almost always called kmalloc.
To compute the size of the RPC buffer more precisely, split p_bufsiz into
two fields; one for the argument size, and one for the result size.
Then, compute the sum of the exact call and reply header sizes, and split
the RPC buffer precisely between the two. That should keep almost all RPC
buffers within the 2KiB buffer mempool limit.
And, we can finally be rid of RPC_SLACK_SPACE!
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
When allocating local ports, do not allow a bind to a port
with a specific local address when a bind to that port with
a wildcard local address already exists.
Noticed by Linus.
Signed-off-by: David S. Miller <davem@davemloft.net>
I accidently applied an earlier version of Eric Dumazet's patch, from
March 21st. His version from March 30th didn't have these bugs, so
this just interdiffs to the correct patch.
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
[IPV4] SNMP: Support OutMcastPkts and OutBcastPkts
[IPV4] SNMP: Support InMcastPkts and InBcastPkts
[IPV4] SNMP: Support InTruncatedPkts
[IPV4] SNMP: Support InNoRoutes
[SNMP]: Add definitions for {In,Out}BcastPkts
[TCP] FRTO: RFC4138 allows Nagle override when new data must be sent
[TCP] FRTO: Delay skb available check until it's mandatory
[XFRM]: Restrict upper layer information by bundle.
[TCP]: Catch skb with S+L bugs earlier
[PATCH] INET : IPV4 UDP lookups converted to a 2 pass algo
[L2TP]: Add the ability to autoload a pppox protocol module.
[SKB]: Introduce skb_queue_walk_safe()
[AF_IUCV/IUCV]: smp_call_function deadlock
[IPV6]: Fix slab corruption running ip6sic
[TCP]: Update references in two old comments
[XFRM]: Export SPD info
[IPV6]: Track device renames in snmp6.
[SCTP]: Fix sctp_getsockopt_local_addrs_old() to use local storage.
[NET]: Remove NETIF_F_INTERNAL_STATS, default to internal stats.
[NETPOLL]: Remove CONFIG_NETPOLL_RX
...
A transmitted IP multicast datagram should be counted as OutMcastPkts.
By the same token, a transmitted IP broadcast datagram should be
counted as OutBcastPkts.
Signed-off-by: Mitsuru Chinen <mitch@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A received IP multicast datagram should be counted as InMcastPkts.
By the same token, a received IP broadcast datagram should be
counted as InBcastPkts.
Signed-off-by: Mitsuru Chinen <mitch@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An IP datagram which is being discarded because the datagram frame
didn't carry enough data should be counted as InTruncatedPkts.
Signed-off-by: Mitsuru Chinen <mitch@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An IP datagram which is being discarded because of no routes in the
forwarding path should be counted as InNoRoutes.
Signed-off-by: Mitsuru Chinen <mitch@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a corner case where less than MSS sized new data thingie
is awaiting in the send queue. For F-RTO to work correctly, a
new data segment must be sent at certain point or F-RTO cannot
be used at all. RFC4138 allows overriding of Nagle at that
point.
Implementation uses frto_counter states 2 and 3 to distinguish
when Nagle override is needed.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
No new data is needed until the first ACK comes, so no need to check
for application limitedness until then.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
On MIPv6 usage, XFRM sub policy is enabled.
When main (IPsec) and sub (MIPv6) policy selectors have the same
address set but different upper layer information (i.e. protocol
number and its ports or type/code), multiple bundle should be created.
However, currently we have issue to use the same bundle created for
the first time with all flows covered by the case.
It is useful for the bundle to have the upper layer information
to be restructured correctly if it does not match with the flow.
1. Bundle was created by two policies
Selector from another policy is added to xfrm_dst.
If the flow does not match the selector, it goes to slow path to
restructure new bundle by single policy.
2. Bundle was created by one policy
Flow cache is added to xfrm_dst as originated one. If the flow does
not match the cache, it goes to slow path to try searching another
policy.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some people want to have many UDP sockets, binded to a single port but
many different addresses. We currently hash all those sockets into a
single chain. Processing of incoming packets is very expensive,
because the whole chain must be examined to find the best match.
I chose in this patch to hash UDP sockets with a hash function that
take into account both their port number and address : This has a
drawback because we need two lookups : one with a given address, one
with a wildcard (null) address.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling smp_call_function can lead to a deadlock if it is called
from tasklet context.
Fixing this deadlock requires to move the smp_call_function from the
tasklet context to a work queue. To do that queue the path pending
interrupts to a separate list and move the path cleanup out of
iucv_path_sever to iucv_path_connect and iucv_path_pending.
This creates a new requirement for iucv_path_connect: it may not be
called from tasklet context anymore.
Also fixed compile problem for CONFIG_HOTPLUG_CPU=n and
another one when walking the cpu_online mask. When doing this,
we must disable cpu hotplug.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This updates references to drafts in comments which must be about 10
years old. Internet draft draft-ietf-tcpimpl-prob-03.txt expired in 1998
and was replaced by RFC 2525 in March 1999.
Section 3.10 of the draft maps almost identically into section 2.17 of RFC
2525: both are entitled "Failure to RST on close with data pending", the
differences in text body amount to a typo and minor sentence change.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch you can use iproute2 in user space to efficiently see
how many policies exist in different directions.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
When network device's are renamed, the IPV6 snmp6 code
gets confused. It doesn't track name changes so it will OOPS
when network device's are removed.
The fix is trivial, just unregister/re-register in notify handler.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_getsockopt_local_addrs_old() in net/sctp/socket.c calls
copy_to_user() while the spinlock addr_lock is held. this should not
be done as copy_to_user() might sleep. the call to
sctp_copy_laddrs_to_user() while holding the lock is also problematic
as it calls copy_to_user()
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu conviced me that a new flag was overkill; every driver
currently overrides get_stats, so we might as well make the internal
one the default. If someone did fail to set get_stats, they would now
get all 0 stats instead of "No statistics available".
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using any of the IEEE80211_DEBUG_XXXX macros in any ieee80211_crypt
routine built as a module results in a missing global for
'ieee80211_debug_level'. The fix is to export the symbol in ieee80211.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are messages arising from ieee80211_crypt that spam the logs
of casual users. These are changed to be logged only if the user
specifically requests the IEEE80211_DEBUG_DROP messages. In either
case, the error/drop count is incremented.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After 13 years of use, it looks like my email address is finally going
to disappear. While this is likely to drop the amount of incoming spam
greatly ;-), it may also affect more appropriate messages, so let's
update my email address in various places. In addition, Host AP mailing
list is subscribers-only and linux-wireless can also be used for
discussing issues related to this driver which is now shown in
MAINTAINERS.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes for various arch compilation problems:
(*) Missing module exports.
(*) Variable name collision when rxkad and af_rxrpc both built in
(rxrpc_debug).
(*) Large constant representation problem (AFS_UUID_TO_UNIX_TIME).
(*) Configuration dependencies.
(*) printk() format warnings.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts eefa390628
The simplification made in that change works with the assumption that
the 'offset' parameter to these functions is always positive or zero,
which is not true. It can be and often is negative in order to access
SKB header values in front of skb->data.
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (46 commits)
dev_dbg: check dev_dbg() arguments
drivers/base/attribute_container.c: use mutex instead of binary semaphore
mod_sysfs_setup() doesn't return errno when kobject_add_dir() failure occurs
s2ram: add arch irq disable/enable hooks
define platform wakeup hook, use in pci_enable_wake()
security: prevent permission checking of file removal via sysfs_remove_group()
device_schedule_callback() needs a module reference
s390: cio: Delay uevents for subchannels
sysfs: bin.c printk fix
Driver core: use mutex instead of semaphore in DMA pool handler
driver core: bus_add_driver should return an error if no bus
debugfs: Add debugfs_create_u64()
the overdue removal of the mount/umount uevents
kobject: Comment and warning fixes to kobject.c
Driver core: warn when userspace writes to the uevent file in a non-supported way
Driver core: make uevent-environment available in uevent-file
kobject core: remove rwsem from struct subsystem
qeth: Remove usage of subsys.rwsem
PHY: remove rwsem use from phy core
IEEE1394: remove rwsem use from ieee1394 core
...
Make use of add_uevent_var() instead of (often incorrectly) open coding it.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Eric Rannaud <eric.rannaud@gmail.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Provide rename event for when we rename network devices.
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6:
selinux: preserve boolean values across policy reloads
selinux: change numbering of boolean directory inodes in selinuxfs
selinux: remove unused enumeration constant from selinuxfs
selinux: explicitly number all selinuxfs inodes
selinux: export initial SID contexts via selinuxfs
selinux: remove userland security class and permission definitions
SELinux: move security_skb_extlbl_sid() out of the security server
MAINTAINERS: update selinux entry
SELinux: rename selinux_netlabel.h to netlabel.h
SELinux: extract the NetLabel SELinux support from the security server
NetLabel: convert a BUG_ON in the CIPSO code to a runtime check
NetLabel: cleanup and document CIPSO constants
When CONFIG_IP_MULTIPLE_TABLES is enabled, the code in nl_fib_lookup()
needs to initialize the res.r field before fib_res_put(&res) - unlike
fib_lookup(), a direct call to ->tb_lookup does not set this field.
Signed-off-by: Sergey Vlasov <vsu@altlinux.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch clarifies the comment about locking in wiphy_unregister.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the locking in wiphy new. Ingo Oeser
<netdev@axxeo.de> noticed that locking in the error case was wrong and
also suggested this fix.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just a few things that didn't fit in with the other patches.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes a bunch of inline abuse from wext. Most functions
that were marked inline are only used once so the compiler will inline
them anyway, others are used multiple times but there's no requirement
for them to be inline since they aren't in any fast paths.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EXPORT_SYMBOL statements are supposed to go together with the symbol
they're exporting. This patch moves them accordingly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the code in wireless_process_ioctl somewhat more
readable.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch kills the two options in wext that are required to be
enabled anyway because they influence the userspace API.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch kills a whole bunch of code that can only ever be used by
defining some things in wext.c. Also, the things that are printed are
mostly useless since the API is fairly well-tested.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up the call paths from the core code into wext.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves dev/core/wireless.c to net/wireless/wext.c.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC [M] net/rxrpc/ar-input.o
net/rxrpc/ar-input.c: In function ‘rxrpc_fast_process_data’:
net/rxrpc/ar-input.c:171: warning: passing argument 2 of ‘__test_and_set_bit’ from incompatible pointer type
net/rxrpc/ar-input.c:180: warning: passing argument 2 of ‘__clear_bit’ from incompatible pointer type
net/rxrpc/ar-input.c:218: warning: passing argument 2 of ‘__clear_bit’ from incompatible pointer type
Signed-off-by: David S. Miller <davem@davemloft.net>
These are done with CPP defines which several platforms
use for their atomic.h implementation, which floods the
build with warnings and breaks the build.
Signed-off-by: David S. Miller <davem@davemloft.net>
Delete the old RxRPC code as it's now no longer used.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an interface to the AF_RXRPC module so that the AFS filesystem module can
more easily make use of the services available. AFS still opens a socket but
then uses the action functions in lieu of sendmsg() and registers an intercept
functions to grab messages before they're queued on the socket Rx queue.
This permits AFS (or whatever) to:
(1) Avoid the overhead of using the recvmsg() call.
(2) Use different keys directly on individual client calls on one socket
rather than having to open a whole slew of sockets, one for each key it
might want to use.
(3) Avoid calling request_key() at the point of issue of a call or opening of
a socket. This is done instead by AFS at the point of open(), unlink() or
other VFS operation and the key handed through.
(4) Request the use of something other than GFP_KERNEL to allocate memory.
Furthermore:
(*) The socket buffer markings used by RxRPC are made available for AFS so
that it can interpret the cooked RxRPC messages itself.
(*) rxgen (un)marshalling abort codes are made available.
The following documentation for the kernel interface is added to
Documentation/networking/rxrpc.txt:
=========================
AF_RXRPC KERNEL INTERFACE
=========================
The AF_RXRPC module also provides an interface for use by in-kernel utilities
such as the AFS filesystem. This permits such a utility to:
(1) Use different keys directly on individual client calls on one socket
rather than having to open a whole slew of sockets, one for each key it
might want to use.
(2) Avoid having RxRPC call request_key() at the point of issue of a call or
opening of a socket. Instead the utility is responsible for requesting a
key at the appropriate point. AFS, for instance, would do this during VFS
operations such as open() or unlink(). The key is then handed through
when the call is initiated.
(3) Request the use of something other than GFP_KERNEL to allocate memory.
(4) Avoid the overhead of using the recvmsg() call. RxRPC messages can be
intercepted before they get put into the socket Rx queue and the socket
buffers manipulated directly.
To use the RxRPC facility, a kernel utility must still open an AF_RXRPC socket,
bind an addess as appropriate and listen if it's to be a server socket, but
then it passes this to the kernel interface functions.
The kernel interface functions are as follows:
(*) Begin a new client call.
struct rxrpc_call *
rxrpc_kernel_begin_call(struct socket *sock,
struct sockaddr_rxrpc *srx,
struct key *key,
unsigned long user_call_ID,
gfp_t gfp);
This allocates the infrastructure to make a new RxRPC call and assigns
call and connection numbers. The call will be made on the UDP port that
the socket is bound to. The call will go to the destination address of a
connected client socket unless an alternative is supplied (srx is
non-NULL).
If a key is supplied then this will be used to secure the call instead of
the key bound to the socket with the RXRPC_SECURITY_KEY sockopt. Calls
secured in this way will still share connections if at all possible.
The user_call_ID is equivalent to that supplied to sendmsg() in the
control data buffer. It is entirely feasible to use this to point to a
kernel data structure.
If this function is successful, an opaque reference to the RxRPC call is
returned. The caller now holds a reference on this and it must be
properly ended.
(*) End a client call.
void rxrpc_kernel_end_call(struct rxrpc_call *call);
This is used to end a previously begun call. The user_call_ID is expunged
from AF_RXRPC's knowledge and will not be seen again in association with
the specified call.
(*) Send data through a call.
int rxrpc_kernel_send_data(struct rxrpc_call *call, struct msghdr *msg,
size_t len);
This is used to supply either the request part of a client call or the
reply part of a server call. msg.msg_iovlen and msg.msg_iov specify the
data buffers to be used. msg_iov may not be NULL and must point
exclusively to in-kernel virtual addresses. msg.msg_flags may be given
MSG_MORE if there will be subsequent data sends for this call.
The msg must not specify a destination address, control data or any flags
other than MSG_MORE. len is the total amount of data to transmit.
(*) Abort a call.
void rxrpc_kernel_abort_call(struct rxrpc_call *call, u32 abort_code);
This is used to abort a call if it's still in an abortable state. The
abort code specified will be placed in the ABORT message sent.
(*) Intercept received RxRPC messages.
typedef void (*rxrpc_interceptor_t)(struct sock *sk,
unsigned long user_call_ID,
struct sk_buff *skb);
void
rxrpc_kernel_intercept_rx_messages(struct socket *sock,
rxrpc_interceptor_t interceptor);
This installs an interceptor function on the specified AF_RXRPC socket.
All messages that would otherwise wind up in the socket's Rx queue are
then diverted to this function. Note that care must be taken to process
the messages in the right order to maintain DATA message sequentiality.
The interceptor function itself is provided with the address of the socket
and handling the incoming message, the ID assigned by the kernel utility
to the call and the socket buffer containing the message.
The skb->mark field indicates the type of message:
MARK MEANING
=============================== =======================================
RXRPC_SKB_MARK_DATA Data message
RXRPC_SKB_MARK_FINAL_ACK Final ACK received for an incoming call
RXRPC_SKB_MARK_BUSY Client call rejected as server busy
RXRPC_SKB_MARK_REMOTE_ABORT Call aborted by peer
RXRPC_SKB_MARK_NET_ERROR Network error detected
RXRPC_SKB_MARK_LOCAL_ERROR Local error encountered
RXRPC_SKB_MARK_NEW_CALL New incoming call awaiting acceptance
The remote abort message can be probed with rxrpc_kernel_get_abort_code().
The two error messages can be probed with rxrpc_kernel_get_error_number().
A new call can be accepted with rxrpc_kernel_accept_call().
Data messages can have their contents extracted with the usual bunch of
socket buffer manipulation functions. A data message can be determined to
be the last one in a sequence with rxrpc_kernel_is_data_last(). When a
data message has been used up, rxrpc_kernel_data_delivered() should be
called on it..
Non-data messages should be handled to rxrpc_kernel_free_skb() to dispose
of. It is possible to get extra refs on all types of message for later
freeing, but this may pin the state of a call until the message is finally
freed.
(*) Accept an incoming call.
struct rxrpc_call *
rxrpc_kernel_accept_call(struct socket *sock,
unsigned long user_call_ID);
This is used to accept an incoming call and to assign it a call ID. This
function is similar to rxrpc_kernel_begin_call() and calls accepted must
be ended in the same way.
If this function is successful, an opaque reference to the RxRPC call is
returned. The caller now holds a reference on this and it must be
properly ended.
(*) Reject an incoming call.
int rxrpc_kernel_reject_call(struct socket *sock);
This is used to reject the first incoming call on the socket's queue with
a BUSY message. -ENODATA is returned if there were no incoming calls.
Other errors may be returned if the call had been aborted (-ECONNABORTED)
or had timed out (-ETIME).
(*) Record the delivery of a data message and free it.
void rxrpc_kernel_data_delivered(struct sk_buff *skb);
This is used to record a data message as having been delivered and to
update the ACK state for the call. The socket buffer will be freed.
(*) Free a message.
void rxrpc_kernel_free_skb(struct sk_buff *skb);
This is used to free a non-DATA socket buffer intercepted from an AF_RXRPC
socket.
(*) Determine if a data message is the last one on a call.
bool rxrpc_kernel_is_data_last(struct sk_buff *skb);
This is used to determine if a socket buffer holds the last data message
to be received for a call (true will be returned if it does, false
if not).
The data message will be part of the reply on a client call and the
request on an incoming call. In the latter case there will be more
messages, but in the former case there will not.
(*) Get the abort code from an abort message.
u32 rxrpc_kernel_get_abort_code(struct sk_buff *skb);
This is used to extract the abort code from a remote abort message.
(*) Get the error number from a local or network error message.
int rxrpc_kernel_get_error_number(struct sk_buff *skb);
This is used to extract the error number from a message indicating either
a local error occurred or a network error occurred.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide AF_RXRPC sockets that can be used to talk to AFS servers, or serve
answers to AFS clients. KerberosIV security is fully supported. The patches
and some example test programs can be found in:
http://people.redhat.com/~dhowells/rxrpc/
This will eventually replace the old implementation of kernel-only RxRPC
currently resident in net/rxrpc/.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This brings the SAD info in sync with net-2.6.22/net-2.6
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set TASK_INTERRUPTIBLE prior to testing the flag to avoid missed wakeups.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
SPIN_LOCK_UNLOCKED cleanup,use __SPIN_LOCK_UNLOCKED instead
Signed-off-by: Milind Arun Choudhary <milindchoudhary@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix http://bugzilla.kernel.org/show_bug.cgi?id=8343
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can save some lines of code by using seq_release_private().
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Acked-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC [M] net/iucv/iucv.o
net/iucv/iucv.c: In function 'iucv_init':
net/iucv/iucv.c:1556: error: 'iucv_cpu_notifier' undeclared (first use in this function)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- make the following needlessly global variables static:
- core/rtnetlink.c: struct rtnl_msg_handlers[]
- netfilter/nf_conntrack_proto.c: struct nf_ct_protos[]
- make the following needlessly global functions static:
- core/rtnetlink.c: rtnl_dump_all()
- netlink/af_netlink.c: netlink_queue_skip()
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I noticed recently that, in skb_checksum(), "offset" and "start" are
essentially the same thing and have the same value throughout the
function, despite being computed differently. Using a single variable
allows some cleanups and makes the skb_checksum() function smaller,
more readable, and presumably marginally faster.
We appear to have many other "sk_buff walker" functions built on the
exact same model, so the cleanup applies to them, too. Here is a list
of the functions I found to be affected:
net/appletalk/ddp.c:atalk_sum_skb()
net/core/datagram.c:skb_copy_datagram_iovec()
net/core/datagram.c:skb_copy_and_csum_datagram()
net/core/skbuff.c:skb_copy_bits()
net/core/skbuff.c:skb_store_bits()
net/core/skbuff.c:skb_checksum()
net/core/skbuff.c:skb_copy_and_csum_bit()
net/core/user_dma.c:dma_skb_copy_datagram_iovec()
net/xfrm/xfrm_algo.c:skb_icv_walk()
net/xfrm/xfrm_algo.c:skb_to_sgvec()
OTOH, I admit I'm a bit surprised, the cleanup is rather obvious so I'm
really wondering if I am missing something. Can anyone please comment
on this?
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
On a system with a lot of SAs, counting SAD entries chews useful
CPU time since you need to dump the whole SAD to user space;
i.e something like ip xfrm state ls | grep -i src | wc -l
I have seen taking literally minutes on a 40K SAs when the system
is swapping.
With this patch, some of the SAD info (that was already being tracked)
is exposed to user space. i.e you do:
ip xfrm state count
And you get the count; you can also pass -s to the command line and
get the hash info.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until this patch the functions which have provided NetLabel support to
SELinux have been integrated into the SELinux security server, which for
various reasons is not really ideal. This patch makes an effort to extract as
much of the NetLabel support from the security server as possibile and move it
into it's own file within the SELinux directory structure.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
This patch changes a BUG_ON in the CIPSO code to a runtime check. It should
also increase the readability of the code as it replaces an unexplained
constant with a well defined macro.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
This patch collects all of the CIPSO constants and puts them in one place; it
also documents each value explaining how the value is derived.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
Writing to /sys/class/net/brX/bridge/stp_state causes a warning because
RTNL is not held when call br_stp_if.c
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a bridge is not running STP, then it has no way to detect a cycle
in the network. But if it is not running STP and some other machine
or device is running STP, then if STP BPDU's get forwarded to it can
detect the cycle.
This is how the old 2.4 and early 2.6 code worked.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pause frames should never make it out of the network device into
the stack. But if a device was misconfigured, it might happen.
So drop pause frames in bridge.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The change to forward STP bpdu's (for usermode STP) through normal path,
changed the packet type in the process. Since link local stuff is multicast, it
should stay pkt_type = PACKET_MULTICAST. The code was probably copy/pasted
incorrectly from the bridge pseudo-device receive path.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because ndisc_send_na(), ndisc_send_ns() and ndisc_send_rs()
are almost identical, so let's unify their common part.
With gcc (GCC) 3.3.5 (Debian 1:3.3.5-13) on i386,
Before:
text data bss dec hex filename
14689 364 24 15077 3ae5 net/ipv6/ndisc.o
After:
text data bss dec hex filename
12317 364 24 12705 31a1 net/ipv6/ndisc.o
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
This patch moves the non-proc SNMP code into addrconf.c and reuses
IPv4 SNMP code where applicable.
As a result we can skip proc.o if /proc is disabled.
Note that I've made a number of functions static since they're only
used by addrconf.c for now. If they ever get used elsewhere we can
always remove the static.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the SNMP code shared between IPv4/IPv6 from proc.c
into net/ipv4/af_inet.c. This makes sense because these functions
aren't specific to /proc.
As a result we can again skip proc.o if /proc is disabled.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid raw division, use ktime_to_timeval() to get usec.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes two enhancements to msg_set_bits():
1) It now ignores any bits of the new field value that are not
covered by the mask being used. (Previously, if the new value
exceeded the size of the mask the extra bits could corrupt
other fields in the message header word being updated.)
2) The code has been optimized to minimize the number of run-time
endianness conversion operations by leveraging the fact that the
mask (and, in some cases, the value as well) is constant and the
necessary conversion can be performed by the compiler.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Jon Paul Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that Patrick has added the code to deal with GSO in netfilter,
we no longer need the crutch that computes partial checksums just
before transmission.
This patch turns this into a warning again. If this goes OK, we
can then turn it into a BUG_ON and remove the gso_send_check cruft.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than using a copy of vegas code, the YEAH code should just have
it exported so there is common code.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do some simple changes to make congestion control API faster/cleaner.
* use ktime_t rather than timeval
* merge rtt sampling into existing ack callback
this means one indirect call versus two per ack.
* use flags bits to store options/settings
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This version more closely matches the paper, and fixes several
math errors. The biggest difference is that it updates alpha/beta
once per RTT
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As scheduled, this patch removes the pointless wext over netlink code.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch creates the core cfg80211 code along with some sysfs bits.
This is a stripped down version to allow mac80211 to function, but
doesn't include any configuration yet except for creating and removing
virtual interfaces.
This patch includes the nl80211 header file but it only contains the
interface types which the cfg80211 interface for creating virtual
interfaces relies on.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch refactors the wireless Kconfig all over and already
introduces net/wireless/Kconfig with just the WEXT bit for now,
the cfg80211 patch will add to that as well.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hint from David Miller <davem@davemloft.net>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because stats pointer may not be aligned for u64, use memcpy
to fill u64 values.
Issue reported by David Miller <davem@davemloft.net>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Correct the function name in the comments supplied with
register_netdev()
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spelling corrections, from "to" to "too".
Signed-off-by: G. Liakhovetski <gl@dsa-ac.de>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In af_irda.c, the multiple IRDA_ASSERT() are either hiding bugs, useless, or
returning the wrong value.
Let's clean that up.
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes a cut'n'paste copy of wait_event_interruptible
from irda_accept.
Signed-off-by: Samuel Ortiz <samuel@ortiz.org>
Acked-by: Olaf Kirch <olaf.kirch@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch silences an IRDA_ASSERT in irda_recvmsg_stream, as described in
http://bugzilla.kernel.org/show_bug.cgi?id=7512 irda_disconnect_indication
would set sk->sk_err to ECONNRESET, and a subsequent call to recvmsg
would print an irritating kernel message and return -1.
When a connected socket is closed by the peer, recvmsg should return 0
rather than an error. This patch fixes this.
Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up some code in irda_recvmsg_stream, replacing some
homebrew code with prepare_to_wait/finish_wait, and by making the
code honor sock_rcvtimeo.
Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is far too large to be an inline and not in any hot paths.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function is quite big and has several call sites and nothing
to collapse by compiler optimization on inlining.
Besides it's nicer to read in a in .c file.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spring cleaning time...
There seems to be a lot of places in the network code that have
extra bogus semicolons after conditionals. Most commonly is a
bogus semicolon after: switch() { }
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an implementation of TCP Illinois invented by Shao Liu
at University of Illinois. It is a another variant of Reno which adapts
the alpha and beta parameters based on RTT. The basic idea is to increase
window less rapidly as delay approaches the maximum. See the papers
and talks to get a more complete description.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It isn't any faster to test a boolean global variable than do a simple
check for empty list.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Getting warnings becuase skb_store_bits has skb as constant,
but the function overwrites it. Looks like const was on the
wrong side.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following is leftover from earlier change in net-2.6.22.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a packet socket option to allow the orig_dev index to be returned
to userspace when passing traffic through a decapsulated device, such
as the bonding driver.
This is very useful for layer 2 traffic being able to report which
physical device actually received the traffic, instead of having the
encapsulating device hide that information.
The new option is called PACKET_ORIGDEV.
Signed-off-by: Peter P. Waskiewicz Jr. <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This also fixes memory leak in error path.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IP(V6)_PMTUDISC_PROBE value for IP(V6)_MTU_DISCOVER. This option forces
us not to fragment, but does not make use of the kernel path MTU discovery.
That is, it allows for user-mode MTU probing (or, packetization-layer path
MTU discovery). This is particularly useful for diagnostic utilities, like
traceroute/tracepath.
Signed-off-by: John Heffner <jheffner@psc.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds a check in ip6_fragment() mirroring ip_fragment() for packets
that we can't fragment, and sends an ICMP Packet Too Big message
in response.
Signed-off-by: John Heffner <jheffner@psc.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch ingress queueing back to use ingress_lock. qdisc_lock_tree now locks
both the ingress and egress qdiscs on the device. All changes to data that
might be used on both ingress and egress needs to be protected by using
qdisc_lock_tree instead of manually taking dev->queue_lock. Additionally
the qdisc stats_lock needs to be initialized to ingress_lock for ingress
qdiscs.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we're now holding the rtnl during the entire dump operation, we
can remove qdisc_tree_lock, whose only purpose is to protect dump
callbacks from concurrent changes to the qdisc tree.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't reinitialize the callback mutex the netlink_kernel_create caller
handed in, it is supposed to already be initialized and could already
be held by someone.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we're now holding the rtnl during the entire dump operation, we can
remove additional locking for rtnl protected data. This patch does that
for all simple cases (dev_base_lock for dev_base walking, RCU protection
for FIB rule dumping).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hold rtnl_mutex during the entire netlink dump operation. This allows
to simplify locking in the dump callbacks, since they can now rely on
that no concurrent changes happen.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch cb_lock to mutex and allow netlink kernel users to override it
with a subsystem specific mutex for consistent locking in dump callbacks.
All netlink_dump_start users have been audited not to rely on any
side-effects of the previously used spinlock.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't fallback to group 0 if no instance can be found for the given group.
This potentially confuses the listener and is not what the user configured.
Also remove the ring buffer spamming that happens when rules are set up
before the logging daemon is started.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
All LOG targets always use their internal logging function nowadays, so
remove the incorrect error message and handle real errors (!= -EEXIST)
by failing to load.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When mangling packets forwarded to a HW checksumming capable device,
offload recalculation of the checksum instead of doing it in software.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The attached patch adds gratuitous arp filtering, more precisely: it
allows checking that the IPv4 source address matches the IPv4
destination address inside the ARP header. It also adds a check for the
hardware address type when matching MAC addresses (nothing critical,
just for better consistency).
Signed-off-by: Bart De Schuymer <bdschuym@pandora.be>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The attached patch by Michael Milner adds support for using iptables and
ip6tables on bridged traffic encapsulated in ppoe frames, similar to
what's already supported for vlan.
Signed-off-by: Michael Milner <milner@blissisland.ca>
Signed-off-by: Bart De Schuymer <bdschuym@pandora.be>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This prints the value of the parsed Elapsed Time when received via a
Timestamp Echo option [RFC 4342, 13.3].
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes an error in the calculation of t_ipi when X converges towards
very low sending rates (between 1 and 64 bytes per second).
Although this case may not sound likely, it can be reproduced by connecting,
hitting enter (1 byte sent) and waiting for some time, during which the
nofeedback timer halves the sending rate until finally it reaches the region
1..64 bytes/sec. Computing X is handled correctly (tested separately); but by
dividing X _before_ entering the calculation of t_ipi, X becomes zero as
a result. This in turn triggers a BUG condition caught in scaled_div().
Fixed by replacing with equivalent statement and explicit typecast for good
measure.
Calculation verified and effect of patch tested - reduced never below 1 byte
per 64 seconds afterwards, i.e. not allowing divide-by-zero.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_copy_expand changes the headroom, so it needs to adjust the header
offsets by the difference between the old and the new value.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch checks kmem_cache_create() error and aborts loading module
on failure.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
For case of bridging pseudo devices, the get created/destroyed (Xen)
need to allow setting address to any valid value.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Need to tell STP daemon about more events, like any time a
device is added even when it is down.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
This patchset based on work by Aji_Srinivas@emc.com provides allows
spanning tree to be controled from userspace. Like hotplug, it
uses call_usermodehelper when spanning tree is enabled so there
is no visible API change. If call to start usermode STP fails
it falls back to existing kernel STP.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
The RSTP daemon needs to be able to flush all dynamic forwarding
entries in the case of topology change.
This is a temporary interface. It will change to a netlink interface
before RSTP daemon is officially released.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Instead of hashing the whole Ethernet address, it should be faster
to just use the last 4 bytes. Add a random salt value to the hash
to make it more difficult to construct worst case DoS hash chains.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
While in the STP learning state, don't route packets; wait until
forwarding delay has expired. The purpose of the forwarding delay
is to detect loops in the network, and if a brouter started up
and started forwarding, it could cause a flood.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Change the bridging hook to be simple function with return value
rather than modifying the skb argument. This could generate better
code and is cleaner.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
When a transmitted packet is looped back directly, CHECKSUM_PARTIAL
maps to the semantics of CHECKSUM_UNNECESSARY. Therefore we should
treat it as such in the stack.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb transport pointer is currently used to specify the start
of the checksum region for transmit checksum offload. Unfortunately,
the same pointer is also used during receive side processing.
This creates a problem when we want to retransmit a received
packet with partial checksums since the skb transport pointer
would be overwritten.
This patch solves this problem by creating a new 16-bit csum_start
offset value to replace the skb transport header for the purpose
of checksums. This offset is calculated from skb->head so that
it does not have to change when skb->data changes.
No extra space is required since csum_offset itself fits within
a 16-bit word so we can use the other 16 bits for csum_start.
For backwards compatibility, just before we push a packet with
partial checksums off into the device driver, we set the skb
transport header to what it would have been under the old scheme.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
esp_init_state doesn't account for the beet pseudo header in the header_len
calculation, which may result in undersized skbs hitting xfrm4_beet_output,
causing unnecessary reallocations in ip_finish_output2.
The skbs should still always have enough room to avoid causing
skb_under_panic in skb_push since we have at least 16 bytes available
from LL_RESERVED_SPACE in xfrm_state_check_space.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the probing based MTU estimation, which usually takes 2-3 iterations
to find a fitting value and may underestimate the MTU, by an exact calculation.
Also fix underestimation of the XFRM trailer_len, which causes unnecessary
reallocations.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we're increasing the headroom, the header offsets need to be
increased by the same amount as well.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When looking up route for destination with rules with
source address restrictions, we may need to find a source
address for the traffic if not given.
Based on patch from Noriaki TAKAMIYA <takamiya@po.ntts.co.jp>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The most common trigger of these errors is that the
config option hasn't been enable wich would make the
functionality available. Therefore returning EOPNOTSUPP
gives a better idea on what is going wrong.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move generic skbuff stuff from XFRM code to generic code so that
AF_RXRPC can use it too.
The kdoc comments I've attached to the functions needs to be checked
by whoever wrote them as I had to make some guesses about the workings
of these functions.
Signed-off-By: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To clearly state the intent of copying to linear sk_buffs, _offset being a
overly long variant but interesting for the sake of saving some bytes.
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Network drivers which keep stats allocate their own stats structure
then write a get_stats() function to return them. It would be nice if
this were done by default.
1) Add a new "stats" field to "struct net_device".
2) Add a new feature field to say "this driver uses the internal one"
3) Have a default "get_stats" which returns NULL if that feature not set.
4) Change callers to check result of get_stats call for NULL, not if
->get_stats is set.
This should not break backwards compatibility with older drivers, yet
allow modern drivers to shed some boilerplate code.
Lightly tested: works for a modified lguest network driver.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
To clearly state the intent of copying from linear sk_buffs, _offset being a
overly long variant but interesting for the sake of saving some bytes.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
As IPPROTO_TCP is 6, it makes sense to make sure inet_protos[] array
is properly cache line aligned to avoid false sharing on SMP.
c0680540 b peer_total
c0680544 b inet_peer_unused_head
c0680560 B inet_protos
On i386 this example, we can see that inet_protos[IPPROTO_TCP] shares
a potentially hot (and modified) cache line.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_memory_pressure and tcp_socket currently share a cache line with tcp_memory_allocated, tcp_sockets_allocated.
(Very hot cache line)
It makes sense to declare these variables as __read_mostly, to avoid false sharing on SMP.
ffffffff8081d9c0 B tcp_orphan_count
ffffffff8081d9c4 B tcp_memory_allocated
ffffffff8081d9c8 B tcp_sockets_allocated
ffffffff8081d9cc B tcp_memory_pressure
ffffffff8081d9d0 b tcp_md5sig_users
ffffffff8081d9d8 b tcp_md5sig_pool
ffffffff8081d9e0 b warntime.31570
ffffffff8081d9e8 b tcp_socket
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The results of FIB rules lookups are cached in the routing cache
except for IPv6 as no such cache exists. So far, it was the
responsibility of the user to flush the cache after modifying any
rules. This lead to many false bug reports due to misunderstanding
of this concept.
This patch automatically flushes the route cache after inserting
or deleting a rule.
Thanks to Muli Ben-Yehuda <muli@il.ibm.com> for catching a bug
in the previous patch.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a very tiny probability that build_ehash_secret() is called
at the same time by different CPUS.
Also, using __read_mostly is a must for inet_ehash_secret
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now Xen has a horrible hack that lets it forward packets with
partial checksums. One of the reasons that CHECKSUM_PARTIAL and
CHECKSUM_COMPLETE were added is so that we can get rid of this hack
(where it creates two extra bits in the skbuff to essentially mirror
ip_summed without being destroyed by the forwarding code).
I had forgotten that I've already gone through all the deivce drivers
last time around to make sure that they're looking at ip_summed ==
CHECKSUM_PARTIAL rather than ip_summed != 0 on transmit. In any case,
I've now done that again so it should definitely be safe.
Unfortunately nobody has yet added any code to update CHECKSUM_COMPLETE
values on forward so we I'm setting that to CHECKSUM_NONE. This should
be safe to remove for bridging but I'd like to check that code path
first.
So here is the patch that lets us get rid of the hack by preserving
ip_summed (mostly) on forwarded packets.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
this is a small patch by Janusz Krzysztofik to ip_route_output_slow()
that allows VIP-less LVS linux director to generate packets
originating >From VIP if sysctl_ip_nonlocal_bind is set.
In a nutshell, the intention is for an LVS linux director to be able
to send ICMP unreachable responses to end-users when real-servers are
removed.
http://archive.linuxvirtualserver.org/html/lvs-users/2007-01/msg00106.html
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of nop rules simplifies the usage of goto rules
and adds more flexibility as they allow targets to remain
while the actual content of the branches can change easly.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rules which match against device names in their selector can
remain while the device itself disappears, in fact the device
doesn't have to present when the rule is added in the first
place. The device name is resolved by trying when the rule is
added and later by listening to NETDEV_REGISTER/UNREGISTER
notifications.
This patch adds the flag FIB_RULE_DEV_DETACHED which is set
towards userspace when a rule contains a device match which
is unresolved at the moment. This eases spotting the reason
why certain rules seem not to function properly.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new rule action FR_ACT_GOTO which allows
to skip a set of rules by jumping to another rule. The rule
to jump to is specified via the FRA_GOTO attribute which
carries a rule preference.
Referring to a rule which doesn't exists is explicitely allowed.
Such goto rules are marked with the flag FIB_RULE_UNRESOLVED
and will act like a rule with a non-matching selector. The rule
will become functional as soon as its target is present.
The goto action enables performance optimizations by reducing
the average number of rules that have to be passed per lookup.
Example:
0: from all lookup local
40: not from all to 192.168.23.128 goto 32766
41: from all fwmark 0xa blackhole
42: from all fwmark 0xff blackhole
32766: from all lookup main
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change tcp_probe to use ktime (needed to add one export).
Add option to only get events when cwnd changes - from Doug Leith
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following update received from Injong updates TCP cubic to the latest
version. I am running more complete tests and will have results after 4/1.
According to Injong: the new version improves on its scalability,
fairness and stability. So in all properties, we confirmed it shows better
performance.
NCSU results (for 2.6.18 and 2.6.20) available:
http://netsrv.csc.ncsu.edu/wiki/index.php/TCP_Testing
This version is described in a new Internet draft for CUBIC.
http://www.ietf.org/internet-drafts/draft-rhee-tcp-cubic-00.txt
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do fragmentation check in ip_forward, similar to ipv6 forwarding.
Signed-off-by: John Heffner <jheffner@psc.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
The days are gone when this was not an issue, there are folks out
there with huge bot networks that can be used to attack the
established hash tables on remote systems.
So just like the routing cache and connection tracking
hash, use Jenkins hash with random secret input.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a new NLA_BINARY attribute policy type with the
verification of simply checking the maximum length of the payload.
It also fixes a small typo in the example.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As stated in the sctp socket api draft:
sac_info: variable
If the sac_state is SCTP_COMM_LOST and an ABORT chunk was received
for this association, sac_info[] contains the complete ABORT chunk as
defined in the SCTP specification RFC2960 [RFC2960] section 3.3.7.
We now save received ABORT chunks into the sac_info field and pass that
to the user.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parameters only take effect when a corresponding flag bit is set
and a value is specified. This means we need to check the flags
in addition to checking for non-zero value.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This option induces partial delivery to run as soon
as the specified amount of data has been accumulated on
the association. However, we give preference to fully
reassembled messages over PD messages. In any case,
window and buffer is freed up.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@.hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This option was introduced in draft-ietf-tsvwg-sctpsocket-13. It
prevents head-of-line blocking in the case of one-to-many endpoint.
Applications enabling this option really must enable SCTP_SNDRCV event
so that they would know where the data belongs. Based on an
earlier patch by Ivan Skytte Jørgensen.
Additionally, this functionality now permits multiple associations
on the same endpoint to enter Partial Delivery. Applications should
be extra careful, when using this functionality, to track EOR indicators.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're holding dev->queue_lock in qdisc_watchdog_schedule and
qdisc_watchdog_cancel, no need for the barriers.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Uninline tcf_destroy and add a helper function to destroy an entire filter
chain.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
netem checks PSCHED_TLESS(cb->time_to_send, now) to find out whether it is
allowed to send a packet, which is equivalent to cb->time_to_send < now.
Use !PSCHED_TLESS(now, cb->time_to_send) instead to properly handle
cb->time_to_send == now.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick has made use of netlink_run_queue() in nfnetlink while my patches
have been waiting for net-2.6.22 to open. So this check for NLM_F_REQUEST
can go as well.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The destructor per conntrack is unnecessary, then this replaces it with
system wide destructor.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is gross, have the wrapper function take the lock.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
No other function calls __nfulnl_send() with inst->skb == NULL than
nfulnl_timer().
Signed-off-by: Michal Miroslaw <mirq-linux@rere.qmqm.pl>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
get_*() don't need access to seq_file - iter_state is enough for them.
Signed-off-by: Michal Miroslaw <mirq-linux@rere.qmqm.pl>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple micro-optimization: Don't change any options if the instance is
being destroyed.
Signed-off-by: Michal Miroslaw <mirq-linux@rere.qmqm.pl>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple micro-optimization: don't call instance_put() on known NULL pointers.
Signed-off-by: Michal Miroslaw <mirq-linux@rere.qmqm.pl>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kill some duplicate code in nfulnl_log_packet().
Signed-off-by: Michal Miroslaw <mirq-linux@rere.qmqm.pl>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't need local nlbufsiz (skb size) as nfulnl_alloc_skb() takes
the maximum anyway.
Signed-off-by: Michal Miroslaw <mirq-linux@rere.qmqm.pl>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of some of my creative spelling.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all users of netlink_dump_start() use netlink_run_queue()
to process the receive queue, it is possible to return -EINTR from
netlink_dump_start() directly, therefore simplying the callers.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Makes use of netlink_run_queue() to process the receive queue and
converts inet_diag_rcv_msg() to use the type safe netlink interface.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error pointer argument in netlink message handlers is used
to signal the special case where processing has to be interrupted
because a dump was started but no error happened. Instead it is
simpler and more clear to return -EINTR and have netlink_run_queue()
deal with getting the queue right.
nfnetlink passed on this error pointer to its subsystem handlers
but only uses it to signal the start of a netlink dump. Therefore
it can be removed there as well.
This patch also cleans up the error handling in the affected
message handlers to be consistent since it had to be touched anyway.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes netlink_rcv_skb() to skip netlink controll messages and don't
pass them on to the message handler.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
netlink_rcv_skb() is changed to skip messages which don't have the
NLM_F_REQUEST bit to avoid every netlink family having to perform this
check on their own.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leftover from dynamic multicast groups allocation work.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If possible, avoid having to do a transmit softirq when a qdisc
watchdog decides to re-enable. The watchdog routine runs off
a timer, so it is already in the same effective context as
the softirq.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netem code would call getnstimeofday() and dequeue/requeue after
every packet, even if it was waiting. Avoid this overhead by using
the throttled flag.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In most cases, the next packet will be sent after the
last one. So optimize that case.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The random number generator always generates 32 bit values.
The time values are limited by psched_tdiff_t
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If you setup netem to just delay packets; "tc qdisc ls" will report
the reordering as 100%. Well it's a lie, reorder isn't used unless
gap is set, so just set value to 0 so the output of utility
is correct.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use willy's work in optimizing cube root by having table for small values.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements a unified, protocol independant rules dumping function
which is capable of both, dumping a specific protocol family or
all of them. This speeds up dumping as less lookups are required.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new interface to register rtnetlink message
handlers replacing the exported rtnl_links[] array which
required many message handlers to be exported unnecessarly.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch follows the following recommendation made in an erratum to RFC 4342:
"Senders MAY additionally make use of other available RTT measurements,
including those from the initial Request-Response packet exchange."
It implements larger initial windows with regard to this inital RTT measurement,
using the mechanism suggested in draft-ietf-dccp-rfc3448bis, section 4.2.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This replaces the existing occurrences of RTT sampling with
the use of the new function dccp_sample_rtt.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recurring problem, in particular in the CCID code, is that RTT samples
from packets with timestamp echo and elapsed time options need to be taken.
This service is provided via a new function dccp_sample_rtt in this patch.
Furthermore, to protect against `insane' RTT samples, the sampled value
is bounded between 100 microseconds and 4 seconds - for which u32 is sufficient.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CCID 3 and TFRC specs (RFC 4342, RFC 3448, draft-3448bis) make frequent
reference to the computation of the RFC-3390 initial sending rate:
1. Initial sending rate when RTT is known (RFC 4342, p. 6)
2. Response to Idle/Application-Limited periods (RFC 4342, 5.1)
This warrants putting the code into its own function, for later code reuse.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This clears the following sparc64 build warnings:
1) warning: format "%ld" expects type "long int", but argument 3 has type "suseconds_t"
2) warning: format "%llu" expects type "long long unsigned int", but argument 3 has type "__u64"
Fixed by using typecast to unsigned. This is argued to be safe, since the quantities, after
de-scaling (factor 2^6) fit all in u32.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a few more fields of interest to /proc/net/dccpprobe, the following output ensues:
1 2 3 4 5 6 7 8 9 10 11
sec.usec src:sport dst:dport size s rtt p X_calc X_recv X t_ipi
Also made the formatting consistent.
Scripts that go with this can be downloaded from http://139.133.210.30/users/gerrit/dccp/dccp_probe/
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds more detail in the wait_for_ccid packet scheduling loop.
In particular, it informs about (i) when delay is used and (ii) why
a packet is discarded.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently debugging output (when configured) is automatically enabled when
DCCP modules are compiled into the kernel rather than built as loadable modules.
This is not necessary, since the module parameters in this case become kernel
commandline parameters, e.g. DCCP or CCID3 debug output can be enabled for a
static build by appending the following at the boot prompt:
dccp.dccp_debug=1 dccp_ccid3.ccid3_debug=1
This patch therefore does away with the more complicated way of always enabling
debug output for static builds
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This:
1. removes a race condition in the access to the scheduled send time t_nom which
results from allowing asynchronous r/w access to t_nom without locks;
2. updates the inter-packet interval t_ipi = s/X when `s' changes, following a
suggestion by Ian McDonald.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a few debugging statements to ccid3.c
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a bug which uses an invalid comparison.
The bug resulted in the use of invalid loss intervals.
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Acked-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This improves the slow-start phase by using the MSS
(as suggested in RFC 4342, sec. 5) instead of the packet size s.
Also figured out that __u32 is ample resource enough.
After applying, I got the following in the logs:
ccid3_hc_tx_packet_recv: client(f7421700), s=6, MSS=1424, w_init=4380, R_sample=176us, X=24886363
Had the previous variant been used, w_init would have been as low as 24.
Committer note: removed unneeded cast to unsigned long long that was
causing a compiler warning on 64bit architectures.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No code change at all.
This splits ccid3.c into a RX and a TX section, so that the file has an
organisation similar to the other ones (e.g. packet_history.{h,c}).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since CCID3 avoids sending 0-byte data packets (cf. ccid3_hc_tx_send_packet),
testing for zero-payload length, as performed by ccid3_hc_tx_update_s, is
redundant - hence removed by this patch.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes two ambiguities in employing the new definition of before48,
following the analysis on http://www.mail-archive.com/dccp@vger.kernel.org/msg01295.html
(1) Updating GSR when P.seqno >= S.SWL
With the old definition we did not update when P.seqno and S.SWL are 2^47 apart. To
ensure the same behaviour as with the old definition, this is replaced with the
equivalent condition dccp_delta_seqno(S.SWL, P.seqno) >= 0
(2) Sending SYNC when P.seqno >= S.OSR
Here it is debatable whether the new definition causes an ambiguity: the case is
similar to (1); and to have consistency with the case (1), we use the equivalent
condition dccp_delta_seqno(S.OSR, P.seqno) >= 0
Detailed Justification
The follows48 relation identifies whether 48-bit sequence number
x is the direct successor of y. Currently, it does not handle cases
of the following type correctly:
follows48(0x(prefix)10000LL, 0x(prefix)0FFFFLL)
where prefix is an arbitrary hex sequence of up to 7 digits.
This is fixed by reusing the new dccp_delta_seqno function.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch
* organizes the sequence arithmetic functions into one corner of dccp.h
* performs a small modification of dccp_set_seqno to make it more widely reusable
(now it is safe to use any number, since it performs modulo-2^48 assignment)
* adds functions and generic macros for 48-bit sequence arithmetic:
--48 bit complement
--modulo-48 addition and modulo-48 subtraction
--dccp_inc_seqno now a special case of add48
Constants renamed following a suggestion by Arnaldo.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the common "(struct nlmsghdr *)skb->data" sequence, so that we reduce the
number of direct accesses to skb->data and for consistency with all the other
cast skb member helpers.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The threshold for root node can be more aggressive set to get
better tree compression. The new setting mekes the root grow
from 16 to 19 bits and substansial improvemnt in Aver depth
this with the current table of 214393 prefixes
But really the dynamic resize should need more investigation
both in terms convergence and performance and maybe it should
be possible to change...
Maybe just for the brave to start with or we may have to back
this out.
The patch below adds break condition for the resize operations. If
we don't achieve the desired fill factor a warning is printed. Trie
should still be operational but new thresholds should be considered.
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
I did it just in alloc_skb_from_cache, forgot __alloc_skb, fixed now.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now to convert the last one, skb->data, that will allow many simplifications
and removal of some of the offset helpers.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So that it is also an offset from skb->head, reduces its size from 8 to 4 bytes
on 64bit architectures, allowing us to combine the 4 bytes hole left by the
layer headers conversion, reducing struct sk_buff size to 256 bytes, i.e. 4
64byte cachelines, and since the sk_buff slab cache is SLAB_HWCACHE_ALIGN...
:-)
Many calculations that previously required that skb->{transport,network,
mac}_header be first converted to a pointer now can be done directly, being
meaningful as offsets or pointers.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rmmoding irda triggers a lockdep false positive.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renaming skb->h to skb->transport_header, skb->nh to skb->network_header and
skb->mac to skb->mac_header, to match the names of the associated helpers
(skb[_[re]set]_{transport,network,mac}_header).
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the common sequence "skb->h.raw - skb->nh.raw", similar to skb->mac_len,
that is precalculated tho, don't think we need to bloat skb with one more
member, so just use this new helper, reducing the number of non-skbuff.h
references to the layer headers even more.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/sched/sch_api.c: In function 'psched_show':
net/sched/sch_api.c:1219: warning: format '%08x' expects type 'unsigned int', but argument 6 has type 's64'
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
q->now is increased during dequeue and doesn't contain the current time
afterwards, resulting in a too large timeout value for the qdisc watchdog.
Use "now" instead, which still contains the current time.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The timer resolution exported in /proc/net/psched is used by userspace to
calculate HTB's burst values. Currently it is set to HZ, since we're now
using hrtimers, use KTIME_MONOTONIC_RES, which makes HTB use smaller burst
values.
This patch also affects libnl, which incorrectly uses this value for
the SFQ perturbation parameter, which is always in seconds, and some
routing cache values, which are in USER_HZ, so both cases are broken
anyway.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all packet schedulers have been converted to hrtimers most users
of PSCHED_JIFFIE2US and PSCHED_US2JIFFIE are gone. The remaining users use
it to convert external time units to packet scheduler clock ticks, so use
PSCHED_TICKS_PER_SEC instead.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch delay_timer to hrtimer.
The class penalty parameter is changed to use psched ticks as units.
Since iproute never supported using this and the only existing user
(libnl) incorrectly assumes psched ticks as units anyway, this
shouldn't break anything.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
cbq_undelay_prio is supposed to return a time delta, but returns the
current time for non-active priorities, causing cbq_undelay to mark
the priority as active and schedule a timer for twice the current
time.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of the manual clock source selection mess and use ktime. Also
use a scalar representation, which allows to clean up pkt_sched.h a bit
more and results in less ktime_to_ns() calls in most cases.
The PSCHED_US2JIFFIE/PSCHED_JIFFIE2US macros are implemented quite
inefficient by this patch, following patches will convert all qdiscs
to hrtimers and get rid of them entirely.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This time we have to set it to skb->tail that is not anymore equal to
skb->data, so we either add a new helper or just add the skb->tail - skb->data
offset, for now do the later.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_nd_hdr is always called immediately after a alloc_skb + skb_reserve
sequence, i.e. when skb->tail is equal to skb->data, making it correct to use
skb_reset_network_header().
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is similar to the skb_reset_network_header(), i.e. at the point we reset
the transport header pointer/offset skb->tail is equal to skb->data.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use nfattr_parse to parse attributes, this patch also modifies the default
behaviour since unknown attributes will be ignored instead of returning
EINVAL. This ensure backward compatibility: new libraries with new
attributes and old kernels can work.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch let userspace programs set the IP_CT_TCP_BE_LIBERAL flag to
force the pickup of established connections.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PUSH flag is accepted with every other valid combination.
Let's get it out of the tcp_valid_flags table and reduce the
number of combinations we have to handle. This does not
significantly reduce the table size however (8 bytes).
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This combination has been encountered on an IBM AS/400 in response
to packets sent to a closed session. There is no particular reason
to mark it invalid.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This unifies the codes to copy netfilter related datas. Before copying,
nf_copy() puts original members in destination skb.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This unifies the codes to copy netfilter related datas. Note that
__nf_copy() assumes destination skb doesn't have any netfilter
related members.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now it uses jhash, but using jhash2 would be around 3-4 times faster
(on P4).
Signed-off-by: Sami Farin <safari-netfilter@safari.iki.fi>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
subsys_table is initialized to NULL, therefore just returns NULL in case
that it is not set.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove nfnetlink_check_attributes duplicates message size and callback
id checks. nfnetlink_find_client and nfnetlink_rcv_msg already do
such checks.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The retrying after an allocation failure is not necessary anymore
since we're holding the mutex the entire time, for the same
reason the double allocation race can't happen anymore.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we don't use nf_conntrack_lock anymore but a single mutex for
all protocol handling, no need to release and grab it again for sysctl
registration.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove ugly special-casing of nf_conntrack_l4proto_generic, all it
wants is its sysctl tables registered, so do that explicitly in an
init function and move the remaining protocol initialization and
cleanup code to nf_conntrack_proto.c as well.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The protocol lookups done by nf_conntrack are already protected by RCU,
there is no need to keep taking nf_conntrack_lock for registration
and unregistration. Switch to a mutex.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the obsolete IPv4 only connection tracking/NAT as scheduled in
feature-removal-schedule.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove xt_proto_prefix array which duplicates xt_prefix and change all
users of xt_proto_prefix to xt_prefix.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the places where we need a pointer to the transport header, it is
still legal to touch skb->h.raw directly if just adding to,
subtracting from or setting it to another layer header.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are a bit more subtle, they are of this type:
- skb->h.raw = payload;
__skb_pull(skb, payload - skb->data);
+ skb_reset_transport_header(skb);
__skb_pull results in:
skb->data = skb->data + payload - skb->data;
skb->data = payload;
So after __skb_pull we have skb->data pointing to payload and we can
just call skb_reset_transport_header(skb), that will do:
skb->h.raw = payload;
The others are similar, allowing us to get rid of some more cases where a
pointer was being attributed to the layer headers.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ip_hdrlen() buddy, created to reduce the number of skb->h.th-> uses and to
avoid the longer, open coded equivalent.
Ditched a no-op in bnx2 in the process.
I wonder if we should have a BUG_ON(skb->h.th->doff < 5) in tcp_optlen()...
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For consistency with all the other skb->h.raw accessors.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For consistency with all the other skb->h.raw accessors.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the cases where the transport header is being set to a offset from
skb->data.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the quite common 'skb->h.raw - skb->data' sequence.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the common, open coded 'skb->h.raw = skb->data' operation, so that we can
later turn skb->h.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.
This one touches just the most simple cases:
skb->h.raw = skb->data;
skb->h.raw = {skb_push|[__]skb_pull}()
The next ones will handle the slightly more "complex" cases.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now the skb->nh union has just one member, .raw, i.e. it is just like the
skb->mac union, strange, no? I'm just leaving it like that till the transport
layer is done with, when we'll rename skb->mac.raw to skb->mac_header (or
->mac_header_offset?), ditto for ->{h,nh}.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use logic operations rather than memcmp() to compare destination
address with link local multicast addresses.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the common sequence "skb->nh.iph->ihl * 4", removing a good number of open
coded skb->nh.iph uses, now to go after the rest...
Just out of curiosity, here are the idioms found to get the same result:
skb->nh.iph->ihl << 2
skb->nh.iph->ihl<<2
skb->nh.iph->ihl * 4
skb->nh.iph->ihl*4
(skb->nh.iph)->ihl * sizeof(u32)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't access skb->nh.raw directly anymore, it will become an offset.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Show what protocols are bound to what packet types in /proc/net/ptype
Uses kallsyms to decode function pointers if possible.
Example:
Type Device Function
ALL eth1 packet_rcv_spkt+0x0
0800 ip_rcv+0x0
0806 arp_rcv+0x0
86dd :ipv6:ipv6_rcv+0x0
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The seq_file operations stuff can be marked constant to
get it out of dirty cache.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For Eric, mark packet type and network device watermarks
as read mostly.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the cases where the network header is being set to a offset from skb->data.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the places where we need a pointer to the network header, it is still legal
to touch skb->nh.raw directly if just adding to, subtracting from or setting it
to another layer header.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the quite common 'skb->nh.raw - skb->data' sequence.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting it to skb->h.raw, which is valid, in the (to become) old pointer based
world order and in the new world of offset based layer headers.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now related to this form:
skb->nh.ipv6h = (struct ipv6hdr *)skb_put(skb, length);
That, as the others, is done when skb->tail is still equal to skb->data, making
the conversion to skb_reset_network_header possible.
Also one more case equivalent to skb->nh.raw = skb->data, of this form:
iph = (struct ipv6hdr *)skb->data;
<SNIP>
skb->nh.ipv6h = iph;
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some more cases where skb->nh.iph was being set that were converted
to using skb_reset_network_header.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
boot_pkt->iph is the first member, that is at skb->data, so just use
skb_reset_network_header().
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This time of the type:
skb->nh.iph = (struct iphdr *)skb->data;
That is completely equivalent to:
skb->nh.raw = skb->data;
Wonder why people love casts... :-)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It returns skb->data, so we can just use skb_reset_network_header after it.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
But only in the cases where its a newly allocated skb, i.e. one where skb->tail
is equal to skb->data, or just after skb_reserve, where this requirement is
maintained.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_push updates and returns skb->data, so we can just call
skb_reset_network_header after the call to skb_push.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the common, open coded 'skb->nh.raw = skb->data' operation, so that we can
later turn skb->nh.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.
This one touches just the most simple case, next will handle the slightly more
"complex" cases.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nh.ipv6h is there exactly for this reason! Use it while it exists ;-)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the places where we need a pointer to the mac header, it is still legal to
touch skb->mac.raw directly if just adding to, subtracting from or setting it
to another layer header.
This one also converts some more cases to skb_reset_mac_header() that my
regex missed as it had no spaces before nor after '=', ugh.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
That is equal to skb->head before skb_reserve, to help in the layer header
changes.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the cases where we want to set skb->mac.raw to an offset from skb->data.
Simple cases first, the memmove ones and specially pktgen will be left for later.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_push updates and returns skb->data, so we can just call
skb_reset_mac_header after the call to skb_push.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->head is equal to skb->data after alloc_skb, so reset the mac header while
this is true, i.e. before skb_reserve.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the common, open coded 'skb->mac.raw = skb->data' operation, so that we can
later turn skb->mac.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.
This one touches just the most simple case, next will handle the slightly more
"complex" cases.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One less thing for drivers writers to worry about.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now all the _type_trans routines are consistent in this regard.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that network timestamps use ktime_t infrastructure, we can add a new
SOL_SOCKET sockopt SO_TIMESTAMPNS.
This command is similar to SO_TIMESTAMP, but permits transmission of
a 'timespec struct' instead of a 'timeval struct' control message.
(nanosecond resolution instead of microsecond)
Control message is labelled SCM_TIMESTAMPNS instead of SCM_TIMESTAMP
A socket cannot mix SO_TIMESTAMP and SO_TIMESTAMPNS : the two modes are
mutually exclusive.
sock_recv_timestamp() became too big to be fully inlined so I added a
__sock_recv_timestamp() helper function.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
CC: linux-arch@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
net_msg_warn should be placed in the read_mostly section, to avoid
performance problems on SMP
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug noticed by Chris Wright <chrisw@sous-sol.org>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We returned incorrect result with IPV6_RTHDRDSTOPTS, IPV6_RTHDR and
IPV6_DSTOPTS.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chuck Lever
Patrick McHardy