Set IDE_AFLAG_DRQ_INTERRUPT in do_identify() instead of ATAPI
device drivers *_setup() methods.
While at it:
- use ata_id_cdb_intr()
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove no longer used ide_host_alloc_all().
* Add MAX_HOST_PORTS define and use it instead of MAX_HWIFS
as the maximum number of host ports possible.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There is now a generic solution [ide_generic_check_pci_legacy_iobases()]
so MIPS-specific ide_probe_legacy() is no longer necessary.
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Rename ->ide_dma_clear_irq method to ->clear_irq
and move it from ide_hwif_t to struct ide_port_ops.
* Move ->waiting_for_dma check inside ->clear_irq method.
* Move ->dma_base check inside ->clear_irq method.
piix.c:
* Add ich_port_ops and remove init_hwif_ich() wrapper.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add 'struct task_s' to ide_hwif_t and init it to the current command
in do_rw_taskfile().
* Merge all TASKFILE_NO_DATA data phase handlers into taskfile_no_intr().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Factor out reset error reporting from reset_pollfunc()
to ide_reset_report_error() helper.
While at it:
- fix KERN_* printk() levels
- remove 'switch ()'
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use 'drive->dn & 1' in ide_init_disk().
* remove [ata_]select_t.
While at it:
* Use ATA_DEVICE_OBS define in ide_port_init_devices_data().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Call ide_port_init_devices() in ide_host_register()
also if 'struct ide_port_info *d' is not available.
* Init drive->dn in ide_port_init_devices() instead of
ide_probe_port() so it is valid also in ->init_dev.
* Pass device number to ide_dev_apply_params().
* Use 'drive->dn & 1' instead of drive->select.b.unit.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move ide*_pm_* enums from ide-io.c to <linux/ide.h>.
* idedisk_pm_* -> ide_pm_*
* ide_pm_state_* -> ide_pm_*
* No need to set ide_pm_* enums to the fixed values.
* Uppercase ide_pm_* enums.
* Fix/update comments.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_DFLAG_LBA device flag and use it instead of ->select.b.lba.
Since ->tf_load uses ->select.all for ATA Device/Head register this
fixes HDIO_DRIVE_TASK[FILE] ioctls for CHS commands on LBA devices.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_DFLAG_DMA_PIO_RETRY and use it instead of
ide_drive_t.state + DMA_PIO_RETRY.
There should be no functional changes cause by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add 'unsigned long dev_flags' to ide_drive_t and convert bitfields
to IDE_DFLAG_* flags.
While at it:
- IDE_DFLAG_ADDRESSING -> IDE_DFLAG_LBA48
- fixup some comments
- remove needless g->flags zeroing from ide*_probe()
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_do_setfeature() helper and convert set_{wcache,acoustic}()
to use it.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Return -EIO if arg > 0 and LBA48 is unsupported.
* No need to reset ->addressing.
* Make ->addressing a single bit flag.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
... with which to control to verbosity of debug messages on module load time.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
[bart: no need to zero debug_mask + move module_param() closer debug_mask]
[bart: init drive->debug_mask in ide_floppy_probe() not in idefloppy_open()]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Also:
- leave in the possibility for optimizing away all debugging macros
- add a PFX macro and prepend all printk calls with it for consistency
- change idefloppy_create_rw_cmd's 1st arg from idefloppy_floppy_t * to
ide_drive_t *.
- add a missing printk-level in idefloppy_init
- fix minor checkpatch warnings
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Introduce to_ide_drv() and ide_drv_g() macros and replace the respective
definitions of similar ones in each driver.
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Because hd.c was moved to drivers/block/ this config option
is superfluous now and may be removed.
v2:
Fix drivers/ide/Makefile (noticed by Adrian Bunk).
Cc: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move ->ticks field from struct ide_floppy_obj to ide_drive_t.
* Move idefloppy_transfer_pc() to ide-atapi.c and make
ide_transfer_pc() use it.
* Always use ide_transfer_pc as a handler in ide_issue_pc().
* Remove no longer used idefloppy_start_pc_transfer(),
ide*_transfer_pc() and 'handler' argument from ide_issue_pc().
* Make ide_transfer_pc() static.
While at it:
* idefloppy_transfer_pc() -> ide_delayed_transfer_pc()
* IDEFLOPPY_TICKS_DELAY -> IDEFLOPPY_PC_DELAY
* ->ticks -> ->pc_delay
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Always use ide_pc_intr as a handler in ide_pc_intr().
* Remove no longer used ide*_pc_intr() and 'handler'
argument from ide_{transfer_pc,pc_intr}().
* Make ide_pc_intr() static.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ->pc_{update,io}_buffers methods to ide_drive_t and use
them instead of {update,io}_buffers ide_pc_intr() arguments.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_create_request_sense_cmd() and ide_retry_pc() helpers
and convert ide-{atapi,floppy,tape}.c to use them.
* Remove no longer used ide*_create_request_sense_cmd(),
ide*_retry_pc() and 'retry_pc' argument from ide_pc_intr().
* Make ide_queue_pc_head() static.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add 'struct ide_atapi_pc request_sense_pc' and 'request request_sense_rq' to
ide_drive_t and use them instead of fields in struct ide_{floppy,tape}_obj.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move idescsi_expiry() to ide-atapi.c.
* Move get_timeout() to <linux/ide.h>.
* Drop 'timeout' and 'expiry' arguments from ide_pc_intr().
While at it:
* idescsi_expiry() -> ide_scsi_expiry()
* get_timeout() -> ide_scsi_get_timeout()
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add pointer to the current packet command (struct ide_atapi_pc *pc)
to ide_drive_t and use it instead of the pointer in struct ide_*_obj.
* Use drive->pc in ide_{issue,transfer}_pc() and ide_pc_intr()
instead of 'pc' argument.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add 'int dsc' argument to ->pc_callback method.
* Call ide_tape_handle_dsc() internally in ide_tape_callback()
if dsc argument is set and update ide_pc_intr() accordingly.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix several issues with the log messages printed by ide_dma_sgiioc4() and
sgiioc4_ide_setup_pci_device():
- IOC4 registers are memory-mapped but the "BM-DMA at" format corresponds to
I/O mapped registers;
- "%p" format specifiers and type casts used to print non-pointer values;
- using KERN_INFO log level for the error message;
- 'hwif->name' printed as drive's name.
While at it, also:
- return more fitting -EBUSY if request_mem_region() fails;
- make the error message style consistent;
- fix indentation, put the printk() facility and message on the same line;
- use comparisions with NULL instead of ! operator..
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: jeremy@sgi.com
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix the drive non-busy criterion used by sgiioc4_read_status(): neither of the
bits it expects to be set guarantees that the drive is not busy (and might be
interrupting), only the BSY bit itself being zero gurantees that.
While at it, use ATA_BUSY instead of hardcoded value everywhere...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: jeremy@sgi.com
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This is a much better version of a previous patch to make the parser
tables constant. Rather than changing the typedef, we put the "const" in
all the various places where its required, allowing the __initconst
exception for nfsroot which was the cause of the previous trouble.
This was posted for review some time ago and I believe its been in -mm
since then.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Cc: Alexander Viro <aviro@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6: (24 commits)
integrity: special fs magic
As pointed out by Jonathan Corbet, the timer must be deleted before
ERROR: code indent should use tabs where possible
The tpm_dev_release function is only called for platform devices, not pnp
Protect tpm_chip_list when transversing it.
Renames num_open to is_open, as only one process can open the file at a time.
Remove the BKL calls from the TPM driver, which were added in the overall
netlabel: Add configuration support for local labeling
cipso: Add support for native local labeling and fixup mapping names
netlabel: Changes to the NetLabel security attributes to allow LSMs to pass full contexts
selinux: Cache NetLabel secattrs in the socket's security struct
selinux: Set socket NetLabel based on connection endpoint
netlabel: Add functionality to set the security attributes of a packet
netlabel: Add network address selectors to the NetLabel/LSM domain mapping
netlabel: Add a generic way to create ordered linked lists of network addrs
netlabel: Replace protocol/NetLabel linking with refrerence counts
smack: Fix missing calls to netlbl_skbuff_err()
selinux: Fix missing calls to netlbl_skbuff_err()
selinux: Fix a problem in security_netlbl_sid_to_secattr()
selinux: Better local/forward check in selinux_ip_postroute()
...
* git://git.infradead.org/users/dwmw2/random-2.6:
Fix autoloading of MacBook Pro backlight driver.
Automatic MODULE_ALIAS() for DMI match tables.
Remove asm/a.out.h files for all architectures without a.out support.
Introduce HAVE_AOUT symbol to remove hard-coded arch list for BINFMT_AOUT
Remove redundant CONFIG_ARCH_SUPPORTS_AOUT
S390: Update comments about why we don't use <asm-generic/statfs.h>
SPARC: Use <asm-generic/statfs.h>
PowerPC: Use <asm-generic/statfs.h>
PARISC: Use <asm-generic/statfs.h>
x86_64: Use <asm-generic/statfs.h>
IA64: Use <asm-generic/statfs.h>
ARM: Use <asm-generic/statfs.h>
Make <asm-generic/statfs.h> suitable for 64-bit platforms.
Define and use PCI_DEVICE_ID_MARVELL_88ALP01_CCIC for CAFÉ camera driver
[MTD] [NAND] Define and use PCI_DEVICE_ID_MARVELL_88ALP01_NAND for CAFÉ
Use PCI_DEVICE_ID_88ALP01 for CAFÉ chip, rather than PCI_DEVICE_ID_CAFE.
EFS: Don't set f_fsid in statfs().
Merges oprofile, timers/hpet, x86/traps, x86/time, and x86/core misc items.
* 'x86-core-v4-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (132 commits)
x86: change early_ioremap to use slots instead of nesting
x86: adjust dependencies for CONFIG_X86_CMOV
dumpstack: x86: various small unification steps, fix
x86: remove additional_cpus
x86: remove additional_cpus configurability
x86: improve UP kernel when CPU-hotplug and SMP is enabled
dumpstack: x86: various small unification steps
dumpstack: i386: make kstack= an early boot-param and add oops=panic
dumpstack: x86: use log_lvl and unify trace formatting
dumptrace: x86: consistently include loglevel, print stack switch
dumpstack: x86: add "end" parameter to valid_stack_ptr and print_context_stack
dumpstack: x86: make printk_address equal
dumpstack: x86: move die_nmi to dumpstack_32.c
traps: x86: finalize unification of traps.c
traps: x86: make traps_32.c and traps_64.c equal
traps: x86: various noop-changes preparing for unification of traps_xx.c
traps: x86_64: use task_pid_nr(tsk) instead of tsk->pid in do_general_protection
traps: i386: expand clear_mem_error and remove from mach_traps.h
traps: x86_64: make io_check_error equal to the one on i386
traps: i386: use preempt_conditional_sti/cli in do_int3
...
Original idea for this from a patch by Rodolfo Giometti which merges various
bits of PPS support
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Drop the kernel lock further and also correct cases where we set rc to an
error code, and then return 0
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
get_current_tty now does internal locking and returns a referenced object,
thus our use of tty_mutex here can go away.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/char/tty_io.c:1413:17: warning: symbol 'buf' shadows an earlier one
drivers/char/tty_io.c:1379:20: originally declared here
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The multiple drivers share the minor space occupied by a particular major
number, the actual index within the device name's space is indicated by
the tty_driver->name_base + uart_port->line
Another usable formula is (uart_driver->minor - MINOR_BASE) + port->line
Use those to print the device names properly in such situations in
serial_core.c and 8250.c
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Closes bug #11408 by checking the card index range for command 0
Fixes the ioctl to return ENOTTY which is correct for unknown ioctls
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many tty drivers contain 'can't happen' checks against NULL pointers passed
in by the tty layer. These have never been possible to occur. Even more
importantly if they ever do occur we want to know as it would be a serious
bug.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stephen's fixes reminded me that gigaset is still rather broken so fix it up
a bit
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Today's linux-next build (x86_64 allmodconfig) failed like this:
/drivers/char/tty_ioctl.c: In function 'change_termios':
drivers/isdn/capi/capi.c🔢 error: implicit declaration of function 'n_tty_ioctl'
drivers/isdn/gigaset/ser-gigaset.c: In function 'gigaset_tty_ioctl':
drivers/isdn/gigaset/ser-gigaset.c:648: error: implicit declaration of function 'n_tty_ioctl'
Introduced by commit 686b5e4aea05a80e370dc931b7f4a8d03c80da54
("tty-move-canon-specials"). I added the following patch (which may not
be correct).
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the set up on ldisc change into the ldisc
Move the INQ/OUTQ cases into the driver not in shared ioctl code where it
gives bogus answers for other ldisc values
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Copy the simplification from the pty unix98 special case to the generic one.
This allows us to kill off driver->termios_locked entirely which is nice. We
have to whack bits of the cris driver as it meddles in places it shouldn't
providing its own arrays that were never used anyway.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need both termios and termios_locked so allocate them as one
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The updating and moving around of the pty code added a bug where both the
helper and caller free the main tty struct (the pty driver must free the
o_tty pair itself however).
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We've done the heavy lifting now its time to mop up a bit
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pass-in 'inode' or 'tty' parameter to devpts interfaces. With multiple
devpts instances, these parameters will be used in subsequent patches
to identify the instance of devpts mounted. The parameters also help
simplify devpts implementation.
Changelog[v3]:
- minor changes due to merge with ttydev updates
- rename parameters to emphasize they are ptmx or pts inodes
- pass-in tty_struct * to devpts_pty_kill() (this will help
cleanup the get_node() call in a subsequent patch)
Signed-off-by: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move tty_driver_lookup_tty() and tty_reopen() from tty_init_dev()
into tty_open() (one of the two callers of tty_init_dev()). These
calls are not really required in ptmx_open(), the other caller,
since ptmx_open() would be setting up a new tty.
Changelog[v2]:
- remove the lookup and reopen calls from ptmx_open
- merge with recent changes to ttydev tree
Signed-off-by: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The majority of the remaining init_dev code is pty special cases. We
refactor this code into the driver->install method.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Original suggestion and proposal from Sukadev Bhattiprolu.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have the lookup operation abstracted which is nice for pty cleanup but
we really want to abstract the add/remove entries as well so that we can
pull the pty code out of the tty core and create a clear defined interface
for the tty driver table.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix up the naming, style and extract some bits of code into the driver
specific code
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the 'find-tty' and 'fast-track-open' parts of init_dev() to
separate functions.
Signed-off-by: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Carry on pushing code out of tty_io when it belongs to other drivers. I'm
not 100% happy with some of this and it will be worth revisiting some of the
exports later when the restructuring work is done.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Right now there are various drivers that try to use tty->count to know when
they get the final close. Aristeau Rozanski showed while debugging the vt
sysfs race that this isn't entirely safe.
Instead of driver side tricks to work around this introduce a shutdown which
is called when the tty is being destructed. This also means that the shutdown
method is tied into the refcounting.
Use this to rework the console close/sysfs logic.
Remove lots of special case code from the tty core code. The pty code can now
have a shutdown() method that replaces the special case hackery in the tree
free up paths.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For hysterical raisins the vt layer drops and retakes locks in the write
method. This is a left over from the days when user/kernel data was passed
directly to the tty not pre-buffered.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The open path for ptmx slaves is via the ptmx device. Opening them any
other way is not allowed. Vegard Nossum found that previously this was not
the case and mknod foo c 128 42; cat foo would produce nasty diagnostics
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently it is sometimes locked by the tty mutex and sometimes by the
sighand lock. The latter is in fact correct and now we can hand back referenced
objects we can fix this up without problems around sleeping functions.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We now have the infrastructure to sort this out but rather than teaching
the syscall tty lock rules we move the hard work into a tty helper
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use tty_port_init and krefs in the stallion drivers to protect us from devices
going away underneath us. As with the other drives some rearranging is done to
pass the tty structure down properly on the user side.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rather than blindly keep taking krefs we reorder the code in a few places
to pass the tty down to the right place (which is important as from the user
side it is not the case that tty == port->tty in all situations). For the irq
and related paths use the krefs to stop the tty being freed under us.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use kref in the USB serial drivers so that we don't free tty structures
from under the URB receive handlers as has historically been the case if
you were unlucky. This also gives us a framework for general tty drivers to
use tty_port objects and refcount.
Contains two err->dev_err changes merged together to fix clashes in the
-next tree.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is pure tty code so put it in the tty layer where it can be with the
locking relevant material it uses
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We now return a kref covered tty reference. That ensures the tty structure
doesn't go away when you have a return from get_current_tty. This is not
enough to protect you from most of the resources being freed behind your
back - yet.
[Updated to include fixes for SELinux problems found by Andrew Morton and
an s390 leak found while debugging the former]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We always use the real tty one for stuff so the pty one should not be
compared. As we propagate window changes to both it doesn't currently
matter but will when we tidy up the pty termios logic a bit more
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This moves us towards sanity and should mean our termios locking is now
complete and comprehensive.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need a way to describe the various additional modes and flow control
features that random weird hardware shows up and software such as wine
wants to emulate as Windows supports them.
TCGETX/TCSETX and the termiox ioctl are a SYS5 extension that we might as
well adopt. This patches adds the structures and the basic ioctl interfaces
when the TCGETX etc defines are added for an architecture. Drivers wishing
to use this stuff need to add new methods.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This came in via another tree and unfortunately is rather broken on
the tty side. Comment the apparent locking problems for someone who knows
the driver to look at.
Fix the termios and other ioctl handling. The driver was calling the wrong
methods for what it wanted to do but the right ones existed so its a simple
fix up.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The tty layer keeps driver module counts that are used so the driver knows
when it can be unloaded. For obvious reasons we want to tie that to the
refcounting properly.
At this point the driver side itself isn't refcounted nicely but we can do
that later and kref the drivers.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce a kref to the tty structure and use it to protect the tty->signal
tty references. For now we don't introduce it for anything else.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The two are basically independent chunks of code so lets split them up for
readability and sanity. It also makes the API boundaries much clearer.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Right now we have ifdefs and hooks in the core ioctl handler for TIOCLINUX
and then test if its a console. This is brain dead. Instead call the
tioclinux helper from the relevant driver ioctl methods.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This requires three changes:
1) Remove !SPARC restriction in Kconfig.
2) Move Sparc specific serial drivers before 8250, so that serial
console devices don't change names on us, even if 8250 finds
devices.
3) Since the Sparc specific serial drivers try to use the
same major/minor device namespace as 8250, some coordination
is necessary. Use the sunserial_*() layer routines to allocate
minor number space within TTY_MAJOR when CONFIG_SPARC.
This has no effect on other platforms.
Thanks to Josip Rodin for bringing up this issue and testing
plus debugging various revisions of this patch.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove some inlines from various functions that are called once, are too
big to inline, or are called only from slow path code. This saves around
300 bytes of code for me.
Signed-off-by: Will Newton <will.newton@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
<rmk> talking about leaks - I noticed that the 'check return of
pci_enable_dev()' in the 8250 pci resume function finally made it in
despite my objections against it (causing stuff in higher levels to
leak).
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes the private check for the termios_initialized for
the pl2303 usb driver. It forced the baud to 9600 on the first call
to pl2303_set_termios()
Based on the tty changes in the 2.6.27 kernel, the termios passed to
the *_set_termios functions is always populated the first time.
This means there is no need to privately initialize the settings the
first time, and doing so will not allow the use of the kernel
parameter "console=ttyUSB0,115200" as an example.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nozomi assumes the close method isn't called if open errors. The tty layer
is different to other drives in this respect however. Pointed out by Denis J
Barrow.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Data read from a TTY can contain an embedded NUL byte (e.g. after
pressing Ctrl-2, or sent to a PTY). After the previous patch, the data
would be logged only up to the first NUL.
This patch modifies the AUDIT_TTY record to always use the hexadecimal
format, which does not terminate at the first NUL byte. The vast
majority of recorded TTY input data will contain either ' ' or '\n', so
the hexadecimal format would have been used anyway.
Signed-off-by: Miloslav Trmac <mitr@redhat.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
add_timer() is not supposed to be called when the timer is pending.
ip2 driver attempts to avoid that condition by setting and resetting
a flag (TimerOn) in timer function. But there is some gap between
add_timer() and setting TimerOn.
This patch fix this problem by using mod_timer() and remove TimerOn
which has been unnecessary by this change.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cleanup of module_init/exit:
- mostly whitespace
- remove empty functions
- replace c++ comments
- remove useless prints (module loaded, unloaded)
- mark the calls as __exit and __init
- use break; and return; to save some indent levels after it
- note resource leakage
It's still mess, but now it's readable.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- do not init .bss zeroed data to zero again (by memset or
explicit assignment)
- use char [] instead of char * for string constants
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's pretty useless to have one setup() function separated along with
module_init() which only calls a function from ip2main anyway. Get rid
of ip2base.
Remove also checks of always-true now.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
board->base is increased for CF cards after mapping. Use board->base2
for unmapping the region, since it holds the original/correct address.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
readl/writel are not expected to accept iomap return value. Replace
bogus mapping by standard ioremap.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For some reason the oti6858 driver undefines and redefines the dbg
macro. This makes it spew debugging messages at KERN_INFO instead of
KERN_DEBUG.
This patch removes the undef and define making the driver log like every
other USB serial driver.
Signed-off-by: Scott Ashcroft <scott.ashcroft@talk21.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We now use the sir_dev/irtty_sir/uart/bfin_serial drivers framework
to monitor the TX status.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
move common variables out of serial headers and into the serial driver and
rename "nr_ports" to "nr_active_ports" so as to easily differentiate
between BFIN_UART_NR_PORTS (the # of available) and nr_ports (the # of enabled)
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch contains the scheduled removal of the obsolete
SERIAL_COLDFIRE driver.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The call to put_tty_driver is out of place and is applied to the wrong
argument.
The function enclosing the patched code calls alloc_tty_driver and stores
the result in drv. Subsequently, there are two occurrences of error
handling code, one making a goto to put_tty and one making a goto to
stop_thread. At the point of the first one the assignment hvc_driver = drv
has not yet been executed, and from inspecting the rest of the file it
seems that hvc_driver would be NULL. Thus the current call to
put_tty_driver is useless, and one applied to drv is needed. The goto
stop_thread is in the error handling code for a call to
tty_register_driver, but the error cases in tty_register_driver do not free
its argument, so it should be done here. Thus, I have moved the put_tty
label after the stop_thread label, so that put_tty_driver is called in both
cases.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
expression E,f;
position p1,p2,p3;
identifier l;
statement S;
@@
x = alloc_tty_driver@p1(...)
...
if (x == NULL) S
... when != E = x
when != put_tty_driver(x)
goto@p2 l;
... when != E = x
when != f(...,x,...)
when any
(
return \(0\|x\);
|
return@p3 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
p3 << r.p3;
@@
print "%s: call on line %s not freed or saved before return on line %s via line %s" % (p1[0].file,p1[0].line,p3[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
alloc_tty_driver is called at the beginning of the function containing the
lines of code shown in the patch. Thus, put_tty_driver is needed before
returning in the error handling code.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@nr exists@
local idexpression x;
expression E,f;
position p1,p2,p3;
identifier l;
statement S;
@@
x = alloc_tty_driver@p1(...)
...
if (x == NULL) S
... when != E = x
when != put_tty_driver(x)
when != goto l;
(
return \(0\|x\);
|
return@p3 ...;
)
@script:python@
p1 << nr.p1;
p3 << nr.p3;
@@
print "%s: call on line %s not freed or saved before return on line %s" % (p1[0].file,p1[0].line,p3[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On MPC8349E-mITX, MPC8315E-RDB and MPC837x-RDB boards there is a
Freescale MC9S08QG8 (MCU) chip with the custom firmware
pre-programmed. The chip is used to power-off the board by the
software, and to control some GPIO pins.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
of/base.c matches on the first (most specific) entries, which isn't
quite practical but it was discussed[1] that this won't change.
The bindings specifies verbose information for the devices, but
it doesn't fit in the I2C ID's 20 characters limit. The limit won't
change[2], and the bindings won't change either as they're correct.
So we have to put an exception for the MPC8349E-mITX-compatible
MCUs.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use new MODULE_DEVICE_TABLE(dmi, ...) facility. There's no need for
every driver to screw it up for themselves, when the alias can be
generated automatically.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Added support for Prof 7300 DVB-S/S2 card. The card
based on cx24116 demodulator.
Signed-off-by: Oleg Roitburd <oroitburd@gmail.com>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
[mchehab@redhat.com: fixed CARDLIST.cx88 entry]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx24116: Change the default SNR units back to percentage by default.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A user tuning DVB-T via the S2API reports that this was not implemented,
and his tuning was failing.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tuning DVB-T via the S2API was failing, missing some essential items.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reports from users that using the new API for tuning DTV was failing,
and the cache was missing some essential items.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I've retained the older percentage code after discussing this with
Darron Broad, but made the ESNO option default.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
... and cleanup any drivers using them.
I've also removed NBC_QPSK and modified the cx24116 driver to check
the delivery_type also, removing some excess namespace baggage.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for DvbWorld USB cards with STV0288 demodulator.
Those cards use Earda EDS-1547 tuner.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove NULL pointer in stb6000 driver,
as it raises error for DvbWorld USB card.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Allow custom inittab for ST STV0288 demodulator,
as it is needed for DvbWorld USB card.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This means that when developers add new commands then they'll be see
the DTV_MAX_COMMAND define and will be more likely to modify it, without
having to modify the command validation code.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes switching from S2API to legacy where legacy params given to S2API
aware demods are cached ones and not those implied in the legacy API.
It was found (on an S2API aware demod at least) that after using
an S2API aware application and then switching to a legacy application
that prior S2API params were in effect were legacy has only
implied values. This fixes this.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Quick fix to stop an OOPS if illegal commands are dumped in S2API.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add some sanity checking to data input via S2API to the cx24116 demod.
This patch is valid for both s2-mfe and s2.
It was found when testing KAFFEINE with S2API support that invalid
modulation modes amongst other parameters were being delivered to
the demod. In order to debug this sanity checking has been added.
An example session would involve kaffeine setting QAM_AUTO when
querying DVB-T, then later when trying to tune to DVB-S this
cached value would be presented in error.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The IR controller has a couple quirks. It won't respond until some other
device on the bus is probed. To work around that, probe 0x50 first.
Then, since it won't respond to a zero-byte read, probe with a one-byte
read.
Signed-off-by: Brian Rogers <brian_rogers@comcast.net>
[mchehab.redhat.com: Fix merge conflicts and remove an unused var]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Modified yuv register update handling to remove a potential race condition
which could occur with the first video frame.
Also removed a forced yuv position update, since changing the source video
dimensions or interlace settings doesn't affect the frame already being
displayed.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When the framebuffer format was queried via VIDIOC_G_FBUF,
V4L2_FBUF_FLAG_OVERLAY would only be correctly returned for certain screen
depths.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The service_set field was used in saa7115 and cx25840 to determine
whether raw or sliced VBI was desired. This is incorrect since it is
perfectly valid to select sliced VBI with a service_set of 0.
Instead these drivers should checked on VIDIOC_S_FMT whether the type
field matches the raw or sliced VBI type.
Updated ivtv accordingly.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the vidioc_enum_fmt_vbi_cap ops: it was scheduled for removal in
2.6.28 since the v4l2 specification says that V4L2_BUF_TYPE_VBI_CAPTURE should
not support VIDIOC_ENUM_FMT. It's also pretty pointless.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Suggested by Martin Dauskardt. This is conform what the other drivers do.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In dvb_init(),
case EM2880_BOARD_TERRATEC_HYBRID_XS:
case EM2880_BOARD_KWORLD_DVB_310U:
can be put in the same case than EM2880_BOARD_HAUPPAUGE_WINTV_HVR_900
since they do the same thing.
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds printk messages, adds checking if frequency is set,
adds return -EINVAL in right places in zoltrix-radio.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Add USB ID for MSI DIGIVOX mini III (1462:8807)
Signed-off-by: Herbert Graeber <herbert@graeber-clan.de>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- enable Maxlinear mxl5005s tuner RSSI
Thaks to Jose Alberto for finding this setting.
Thanks-to: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- fix wrong GPIO that causes 2nd FE not to work ater warmboot
Thanks to Andrew Williams <andrew.williams@joratech.com> for reporting this.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit 2e88810329
(phylib: add mdiobus_{read,write}) causes the
following compile error:
<-- snip -->
...
CC drivers/net/bfin_mac.o
drivers/net/bfin_mac.c:272: error: conflicting types for 'mdiobus_read'
include/linux/phy.h:130: error: previous declaration of 'mdiobus_read' was here
drivers/net/bfin_mac.c:287: error: conflicting types for 'mdiobus_write'
include/linux/phy.h:131: error: previous declaration of 'mdiobus_write' was here
make[3]: *** [drivers/net/bfin_mac.o] Error 1
<-- snip -->
This patch prefixes the driver functions with bfin_
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The file(s) below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
drivers/net/jme.c
This patch removes the said #include <version.h>.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LAN92{5,7,8} chips from SMSC are register compatible with LAN911{5,6,7,8}
controllers, and only add support for HP Auto-MDIX. LAN9218 doesn't have
an external MII interface.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed duplicated include <linux/init.h> in files below
drivers/net/qlge/qlge_ethtool.c
drivers/net/qlge/qlge_main.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2e88810329
(phylib: add mdiobus_{read,write}) causes the
following compile error:
<-- snip -->
...
CC drivers/net/au1000_eth.o
drivers/net/au1000_eth.c:252: error: conflicting types for 'mdiobus_read'
include/linux/phy.h:130: error: previous declaration of 'mdiobus_read' was here
drivers/net/au1000_eth.c:263: error: conflicting types for 'mdiobus_write'
include/linux/phy.h:131: error: previous declaration of 'mdiobus_write' was here
...
make[3]: *** [drivers/net/au1000_eth.o] Error 1
<-- snip -->
This patch prefixes the driver functions with au1000_
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix an obvious typo introduced by
commit 298cf9beb9
(phylib: move to dynamic allocation of struct mii_bus).
<-- snip -->
...
CC drivers/net/tc35815.o
drivers/net/tc35815.c: In function 'tc_mii_init':
drivers/net/tc35815.c:799: error: 'err_out_free_mii_bus' undeclared (first use in this function)
drivers/net/tc35815.c:799: error: (Each undeclared identifier is reported only once
drivers/net/tc35815.c:799: error: for each function it appears in.)
drivers/net/tc35815.c:781: error: label 'err_out_free_mii_bus' used but not defined
make[3]: *** [drivers/net/tc35815.o] Error 1
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since dev->power.should_wakeup bit is used by the PCI core to
decide whether the device should wake up the system from sleep
states, set/unset this bit whenever WOL is enabled/disabled using
sky2_set_wol().
Remove an open-coded reference to the standard PCI PM registers that
is not used any more.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
mmio_addr in r8169 needs to be initialized before use
Maybe that all tp-> initialization should be moved before rtl_init_mac_address call,
but this is enough to get rid of crash in rtl_rar_set due to mmio_addr being uninitialized.
Signed-off-by: Petr Vandrovec <petr@vandrovec.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
The helper is factored out of of_get_gpio(). Will be used by the QE
pin multiplexing functions (they need to parse the gpios = <> too).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It needs the WM97xx touchscreen driver to be compiled in, not as a
module. And it cannot itself be a module, due to some unfortunate
interactions with platform data.
Reported-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This merges in:
x86/build, x86/microcode, x86/spinlocks, x86/memory-corruption-check,
x86/early-printk, x86/xsave, x86/quirks, x86/setup, x86/signal,
core/signal, x86/urgent, x86/xen
* 'x86-core-v2-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (142 commits)
x86: make processor type select depend on CONFIG_EMBEDDED
x86: extend processor type select help text
x86, amd-iommu: propagate PCI device enabling error
warnings: fix arch/x86/kernel/io_apic_64.c
warnings: fix arch/x86/kernel/early_printk.c
x86, fpu: check __clear_user() return value
x86: memory corruption check - cleanup
x86: ioperm user_regset
xen: do not reserve 2 pages of padding between hypervisor and fixmap.
xen: use spin_lock_nest_lock when pinning a pagetable
x86: xsave: set FP, SSE bits in the xsave header in the user sigcontext
x86: xsave: fix error condition in save_i387_xstate()
x86: SB450: deprioritize DMI quirks
x86: SB450: skip IRQ0 override if it is not routed to INT2 of IOAPIC
x86: replace a magic number with a named constant in the VESA boot code
x86 setup: remove IMAGE_OFFSET
x86 setup: remove DEF_INITSEG and DEF_SETUPSEG
Revert "x86: fix ghost EDD devices in /sys again"
x86 setup: fix ghost entries under /sys/firmware/edd take 3
x86: signal: remove indent in restore_sigcontext()
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (24 commits)
MMC: Use timeout values from CSR
MMC: CSD and CID timeout values
sdhci: 'scratch' may be used uninitialized
mmc: explicitly mention SDIO support in Kconfig
mmc: remove redundant "depends on"
Fix comment in include/linux/mmc/host.h
sdio: high-speed support
mmc_block: hard code 512 byte block size
sdhci: force high speed capability on some controllers
mmc_block: filter out PC requests
mmc_block: indicate strict ordering
mmc_block: inform block layer about sector count restriction
sdio: give sdio irq thread a host specific name
sdio: make sleep on error interruptable
sdhci: reduce card detection delay
sdhci: let the controller wait for busy state to end
atmel-mci: Add missing flush_dcache_page() in PIO transfer code
atmel-mci: Don't overwrite error bits when NOTBUSY is set
atmel-mci: Add experimental DMA support
atmel-mci: support multiple mmc slots
...
Commit ed458df4d2 ("PnP: move
pnpacpi/pnpbios_init to after PCI init") moved the PnP RTC discovery
later, and now the ACPI RTC glue code doesn't find it any more, breaking
the RTC wakealarm sysfs interfaces, as reported by Rafael.
This really is fairly messy, and we have several annoying ordering
constraints here - the PnP code that sets up the RTC resources wants to
run after the PCI resources have to be registered, which in turn needs
to run after ACPI has at least enumerated the root PCI buses etc. Our
initcall ordering is not fine-grained enough to make this all painless.
So this moves the ACPI RTC glue ("acpi_rtc_init()") down to a regular
module call, which fixes the problem Rafael has. The reason this isn't
wonderful is that we really should do acpi_rtc_init before we do the
rtc_cmos init, and now those two are in the same module_init() section.
Which happens to work, but only because drivers/rtc is linked after
drivers/acpi. In other words, we still have a very subtle ordering
issue here. Grr.
Reported-and-tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
RAID autodetect has the side effect of requiring synchronisation
of all device drivers, which can make the boot several seconds longer
(I've measured 7 on one of my laptops).... even for systems that don't
have RAID setup for the root filesystem (the only FS where this matters).
This patch makes the default for autodetect a config option; either way
the user can always override via the kernel command line.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: NeilBrown <neilb@suse.de>
Move the prototypes from the generic kernel.h header to the more
appropriate include/asm-x86/bios_ebda.h header file.
Also, remove the check from the power management code - this is a
pure x86 matter for now.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Prevent the zoran driver sources from cluttering the video directory.
This changeset only moves the drivers and it does not fix any of the
checkpatch warnings/errors to keep the changeset clean.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Well, one thing you encouraged me to do was re-test some of my cards
which contained the xc3028-zarlink combo.
Which led me to test a Dvico FusionHDTV Pro.
Almost a year ago, Chris Pascoe did a patch for this which can be found
at his ~pascoe/xc-test at Linuxtv.
This worked very well, however that was using his version of firmware.
Alas, someone attempted to use this and patch v4l-dvb, and messed it up.
So I've fixed it.
I enclose the patch against today's tree (containing your latest
tuner-xc2028.c patch).
The card now works very well, well with DVB-T anyway.
Signed-off-by: Tim Farrington <timf@iinet.net.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l core creates four different video devices (video, vbi, radio, vtx)
and each has its own range of minor numbers. However, modern devices keep
increasing the number of devices that they need so a maximum of 64 video
devices will not be enough in the future. In addition this scheme makes
it very hard to add new device types.
This patch disconnects the kernel number allocation (e.g. video0, video1,
etc.) from the actual minor number (just pick the first free minor).
This allows for much more flexibility in the future. However, it does
require the use of udev. For those who cannot use udev a new CONFIG option
was created that changes the allocation scheme back to the old behavior.
Thanks to Greg KH for suggesting this approach during the 2008 LPC.
In addition, several bugs were fixed in the ivtv and cx18 drivers: these
drivers try to allocate specific kernel numbers but that scheme contained
a bug which caused what should have been e.g. video17 to appear as e.g.
video2.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Fix warning message for DMA done notification for inactive stream. The
warning message would always gripe that the radio stream was to blame, which
was misleading and wrong (/dev/radioN nodes never transfer data).
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Add entries for the Leadtek PVR2100 and Toshiba Qosmio DVB-T/Analog
capture cards. Both cards are hybrids cards, but no digital capture
functionality has been added yet. These entries are a first guess at the card
entries to get analog working, given the information available. Terry Wu
<terrywu at leadtek.com.tw> provided a pointer to information for the PVR2100.
Martin Juhl <mj at casalogic.dk>, an owner of the Toshiba DVB-T/Analog tuner
card, provided the DDR timing information from his Windows inf file.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- separate functions for bridge and sensor exchanges
- delays added after some exchanges
- other sensor type
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
USB should not be having it's own printk macros, so remove info() and
use the system-wide standard of dev_info() wherever possible.
Cc: Douglas Landgraf <dougsland@gmail.com>
Cc: Mike Isely <isely@pobox.com>
Cc: Thierry Merle <thierry.merle@free.fr>
Cc: Antoine Jacquet <royale@zerezo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Put callback definition before function return and cleanup callback:
Fix a bug where the xc5000 callback was being set *after* the
return call (essentially resulting in dead code).
Also cleanup the callback function to detect unknown commands.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In opposite to the P7131 Dual this early OEM card has a male
radio antenna connector and also no remote.
We currently switch the DVB-T RF feed to the radio input, like
on the P7131 with female radio connector used also for DVB-T
and should improve this.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Up the version to 1.0.1. This will make it easy to tell if retries
of MMIO access are implemented or not in trouble reports. First course of
action for I2C and other initialization problem reports will be to have user
upgrade to v1.0.1 of driver.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Bartlomiej Zolnierkiewicz