These days, the NACA only exists on iSeries. Therefore, this patch
moves naca.h from include/asm-ppc64 to arch/powerpc/platforms/iseries.
There was one file including naca.h outside of platforms/iseries -
arch/ppc64/kernel/udbg_scc.c. However, that's obviously a hangover
from older days. The include is not necessary, so this patch simply
removes it.
Built and booted on iSeries, built for G5 (which uses udbg_scc.o).
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
asm-ppc64/dart.h is included in exactly one place -
arch/powerpc/sysdev/u3_iommu.c. This patch, therefore, moves it into
arch/powerpc/sysdev. While we're at it, update the #ifndef/#define
protecting the include, and the filename in the comments of
u3_iommu.c.
Built and booted on pSeries and G5, built for ppc32 powermac.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ppc64 versions of numnodes.h and sparsemem.h can be safely moved
to asm-powerpc with no changes apart from changing the #define to the
standard _ASM_POWERPC_ form. There are no ppc32 versions of these
files, because they only have any effect if CONFIG_SPARSEMEM is
enabled, which it never can be on ppc32.
Built and booted on pSeries (POWER5), built for 32-bit powermac.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch merges the ppc32 and ppc64 versions of futex.h, essentially
by taking the ppc64 version as the powerpc version. The old ppc32
version did not implement the futex_atomic_op_inuser() callback (it
always returned -ENOSYS), so FUTEX_WAKE_OP would not work on ppc32.
In fact the ppc64 version of this function is almost suitable for
ppc32 as well - the only change needed is to extend ppc_asm.h with a
macro expanding to to the right pseudo-op to store a pointer (either
".long" or ".llong").
Built and booted on pSeries. Built for 32-bit powermac.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Here's a revised version. This re-introduces the set_bits() function
from ppc64, which I removed because I thought it was unused (it exists
on no other arch). In fact it is used in the powermac interrupt code
(but not on pSeries).
- We use LARXL/STCXL macros to generate the right (32 or 64 bit)
instructions, similar to LDL/STL from ppc_asm.h, used in fpu.S
- ppc32 previously used a full "sync" barrier at the end of
test_and_*_bit(), whereas ppc64 used an "isync". The merged version
uses "isync", since I believe that's sufficient.
- The ppc64 versions of then minix_*() bitmap functions have changed
semantics. Previously on ppc64, these functions were big-endian
(that is bit 0 was the LSB in the first 64-bit, big-endian word).
On ppc32 (and x86, for that matter, they were little-endian. As far
as I can tell, the big-endian usage was simply wrong - I guess
no-one ever tried to use minixfs on ppc64.
- On ppc32 find_next_bit() and find_next_zero_bit() are no longer
inline (they were already out-of-line on ppc64).
- For ppc64, sched_find_first_bit() has moved from mmu_context.h to
the merged bitops. What it was doing in mmu_context.h in the first
place, I have no idea.
- The fls() function is now implemented using the cntlzw instruction
on ppc64, instead of generic_fls(), as it already was on ppc32.
- For ARCH=ppc, this patch requires adding arch/powerpc/lib to the
arch/ppc/Makefile. This in turn requires some changes to
arch/powerpc/lib/Makefile which didn't correctly handle ARCH=ppc.
Built and running on G5.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch merges ppc32 and ppc64 versions of ipcbuf.h. The merge is
essentially trivial, since the structure defined in each version was
already identical. Only wrinkle is that the merged version now
includes linux/types.h in order to get the fixed width integer types.
In fact, the old versions probably should have been including that
anyway, since the file uses various __kernel_*_t types.
Built and booted on G5, built for 32-bit pmac, but not booted, since
the merge tree currently doesn't boot there.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
During the conversion to the merge tree, the Cell specific
SMP initialization was removed from the pSeries code.
This creates a new Cell specific SMP implementation file.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The official name for BPA is now CBEA (Cell Broadband
Engine Architecture). This patch renames all occurences
of the term BPA to 'Cell' for easier recognition.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We had a static memory_limit in prom.c, and then another one defined
in setup_64.c and used in numa.c, which resulted in the kernel crashing
when mem=xxx was given on the command line. This puts the declaration
in system.h and the definition in mem.c. This also moves the
definition of tce_alloc_start/end out of setup_64.c.
Signed-off-by: Paul Mackerras <paulus@samba.org>
__MUTEX_INITIALIZER() has no users, and equates to the more commonly used
DECLARE_MUTEX(), thus making it pretty much redundant. Remove it for good.
Signed-off-by: Arthur Othieno <a.othieno@bluewin.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make sure we always return, as all syscalls should. Also move the common
prototype to <linux/syscalls.h>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following series implements memory hot-add for ppc64 and i386. There are
x86_64 and ia64 implementations that will be submitted shortly as well,
through the normal maintainers.
This patch:
local_mapnr is unused, except for in an alpha header. Keep the alpha one,
kill the rest.
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Impose a little more consistency on the page fault handlers do_wp_page,
do_swap_page, do_anonymous_page, do_no_page, do_file_page: why not pass their
arguments in the same order, called the same names?
break_cow is all very well, but what it did was inlined elsewhere: easier to
compare if it's brought back into do_wp_page.
do_file_page's fallback to do_no_page dates from a time when we were testing
pte_file by using it wherever possible: currently it's peculiar to nonlinear
vmas, so just check that. BUG_ON if not? Better not, it's probably page
table corruption, so just show the pte: hmm, there's a pte_ERROR macro, let's
use that for do_wp_page's invalid pfn too.
Hah! Someone in the ppc64 world noticed pte_ERROR was unused so removed it:
restored (and say "pud" not "pmd" in its pud_ERROR).
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add sem_is_read/write_locked functions to the read/write semaphores, along the
same lines of the *_is_locked spinlock functions. The swap token tuning patch
uses sem_is_read_locked; sem_is_write_locked is added for completeness.
Signed-off-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change the phys_mem_access_prot() function to take a pfn instead of an
address. This allows mmap64() to work on /dev/mem for addresses above 4G
on 32-bit architectures. We start with a pfn in mmap_mem(), so there's no
need to convert to an address; in fact, it's actively bad, since the
conversion can overflow when the address is above 4G.
Similarly fix the ppc32 page_is_ram() function to avoid a conversion to an
address by directly comparing to max_pfn. Working with max_pfn instead of
high_memory fixes page_is_ram() to give the right answer for highmem pages.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The sc instruction emulation can't be done the same way on 32-bit
as 64-bit yet, but this should work OK.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch moves the XICS interrupt controller code into the
platforms/pseries directory, since it only appears on pSeries
machines. If it ever appears on some other machine we can move it to
sysdev, although xics.c itself will need a bunch of changes in that
case to remove pSeries specific assumptions.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since I sent the patch to purge bootinfo.h from ARCH=powerpc and
ARCH=ppc64, setup-common.c has come into existence, and another
#include of bootinfo.h slipped in. This patch removes it. It also
removes include/asm-ppc64/bootinfo.h, which somehow survived the
previous patch which was supposed to remove it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Save for the header #define, ppc32 and ppc64 versions of parport.h are
identical. This patch merges them.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The recent merge of fpu.S broken the handling of fpscr for
ARCH=powerpc and CONFIG_PPC64=y. FP registers could be corrupted,
leading to strange random application crashes.
The confusion arises, because the thread_struct has (and requires) a
64-bit area to save the fpscr, because we use load/store double
instructions to get it in to/out of the FPU. However, only the low
32-bits are actually used, so we want to treat it as a 32-bit quantity
when manipulating its bits to avoid extra load/stores on 32-bit. This
patch replaces the current definition with a structure of two 32-bit
quantities (pad and val), to clarify things as much as is possible.
The 'val' field is used when manipulating bits, the structure itself
is used when obtaining the address for loading/unloading the value
from the FPU.
While we're at it, consolidate the 4 (!) almost identical versions of
cvt_fd() and cvt_df() (arch/ppc/kernel/misc.S,
arch/ppc64/kernel/misc.S, arch/powerpc/kernel/misc_32.S,
arch/powerpc/kernel/misc_64.S) into a single version in fpu.S. The
new version takes a pointer to thread_struct and applies the correct
offset itself, rather than a pointer to the fpscr field itself, again
to avoid confusion as to which is the correct field to use.
Finally, this patch makes ARCH=ppc64 also use the consolidated fpu.S
code, which it previously did not.
Built for G5 (ARCH=ppc64 and ARCH=powerpc), 32-bit powermac (ARCH=ppc
and ARCH=powerpc) and Walnut (ARCH=ppc, CONFIG_MATH_EMULATION=y).
Booted on G5 (ARCH=powerpc) and things which previously fell over no
longer do.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There has been a need expressed for dma_addr_t to be 64 bits on PPC64.
This patch does that.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move include/asm-ppc64/vio.h to include/asm-powerpc/vio.h, that's it.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
This brings in a lot of changes from arch/ppc64/kernel/pmac_*.c to
arch/powerpc/platforms/powermac/*.c and makes various minor tweaks
elsewhere. On the powermac we now initialize ppc_md by copying
the whole pmac_md structure into it, which required some changes in
the ordering of initializations of individual fields of it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Moved init_boot_display from arch/ppc64/kernel/pmac_setup.c to
arch/ppc64/kernel/btext.c and declared it in asm-ppc64/btext.h.
Call it from init_early rather than pmac_init_early.
Signed-off-by: Paul Mackerras <paulus@samba.org>
... for consistency with ppc32 and to make the powermac merge easier.
Also make it use just a single resource in the host bridge for multiple
consecutive elements of the ranges property.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Merge ppc32 and ppc64 versions of thread_info.h. They were pretty
similar already, the chief changes are:
- Instead of inline asm to implement current_thread_info(),
which needs to be different for ppc32 and ppc64, we use C with an
asm("r1") register variable. gcc turns it into the same asm as we
used to have for both platforms.
- We replace ppc32's 'local_flags' with the ppc64
'syscall_noerror' field. The noerror flag was in fact the only thing
in the local_flags field anyway, so the ppc64 approach is simpler, and
means we only need a load-immediate/store instead of load/mask/store
when clearing the flag.
- In readiness for 64k pages, when THREAD_SIZE will be less
than a page, ppc64 used kmalloc() rather than get_free_pages() to
allocate the kernel stack. With this patch we do the same for ppc32,
since there's no strong reason not to.
- For ppc64, we no longer export THREAD_SHIFT and THREAD_SIZE
via asm-offsets, thread_info.h can now be safely included in asm, as
on ppc32.
Built and booted on G4 Powerbook (ARCH=ppc and ARCH=powerpc) and
Power5 (ARCH=ppc64 and ARCH=powerpc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This declares powersave_nap in system.h and makes it an int everywhere,
fixes typos for the maple platform, fixes a couple of places where
I missed removing the last two arguments from a message_pass function,
and makes ppc64 consistent with ppc32 in the type of the
pci_bridge.cfg_data field.
Signed-off-by: Paul Mackerras <paulus@samba.org>
