* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] use generic compat_old_sys_readdir
[IA64] pci_acpi_scan_root cleanup
[IA64] Shrink shadow_flush_counts to a short array to save 8k of per_cpu area.
[IA64] Remove sn2_defconfig.
Switch ia64 to the generic compat_sys_old_readdir which is identical
except for slightly better error handling. Also remove sys32_getdents
which already isn't wired up to the syscall table anymore in favour of
compat_sys_getdents.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The code walks all the acpi _CRS methods to see how many windows
to allocate. It then scans them all again to insert_resource()
for each *even if the first scan found that there were none*.
Move the second scan inside the "if (windows)" clause.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Making allmodconfig will break the current build. This patch shrinks
the per_cpu__shadow_flush_counts from 16k to 8k which frees enough space
to allow allmodconfig to successfully complete.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=11338
Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Not really a patch as much as a remove this file request. Now that
generic_defconfig supports all the configurations SGI currently supports
and has NR_CPUS and NR_NODES at our largest configurations, we have no
reason to maintain the extra defconfig file.
Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch removes code that became unused through IDE changes and the
arch/ppc/ removal.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc: Use generic compat_sys_old_readdir
powerpc/kexec: Fix up KEXEC_CONTROL_CODE_SIZE missed during conversion
powerpc: Remove dead module_find_bug code
powerpc: Add CMO enabled flag and paging space data to lparcfg
powerpc: Fix CMM page loaning on 64k page kernel with 4k hardware pages
powerpc: Make CMO paging space pool ID and page size available
powerpc: Fix lockdep IRQ tracing bug
powerpc: Fix TLB invalidation on boot on 32-bit
powerpc: Fix loss of vdso on fork on 32-bit
This recent patch
commit c3965bd151
Author: Paul Jackson <pj@sgi.com>
Date: Wed May 14 08:15:34 2008 -0700
x86 boot: proper use of ARRAY_SIZE instead of repeated E820MAX constant
caused these new warnings during a normal build:
In file included from linux-2.6/arch/x86/boot/memory.c:17:
linux-2.6/include/linux/log2.h: In function '__ilog2_u32':
linux-2.6/include/linux/log2.h:34: warning: implicit declaration of function 'fls'
linux-2.6/include/linux/log2.h: In function '__ilog2_u64':
linux-2.6/include/linux/log2.h:42: warning: implicit declaration of function 'fls64'
linux-2.6/include/linux/log2.h: In function '__roundup_pow_of_two ':
linux-2.6/include/linux/log2.h:63: warning: implicit declaration of function 'fls_long'
I tried to fix them in log2.h, but it's difficult because the real mode
environment is completely different from a normal kernel environment. Instead
define an own ARRAY_SIZE macro in boot.h, similar to the other private
macros there.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
WARNING: vmlinux.o(.text+0x27032): Section mismatch in reference from the function get_tce_space_from_tar() to the function .init.text:calgary_bus_has_devices()
The function get_tce_space_from_tar() references
the function __init calgary_bus_has_devices().
This is often because get_tce_space_from_tar lacks a __init
annotation or the annotation of calgary_bus_has_devices is wrong.
get_tce_space_from_tar is called only from __init function (calgary_init)
and calls __init function (calgary_bus_has_devices).
So annotate it properly.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Chandru Siddalingappa <chandru@in.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Take out part of get_local_pda referencing __init function (free_bootmem)
to new (static) function marked as __ref. It's safe to do because free_bootmem
is called before __init sections are dropped.
WARNING: vmlinux.o(.cpuinit.text+0x3cd7): Section mismatch in reference from the function get_local_pda() to the function .init.text:free_bootmem()
The function __cpuinit get_local_pda() references
a function __init free_bootmem().
If free_bootmem is only used by get_local_pda then
annotate free_bootmem with a matching annotation.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
arch/x86/power/cpu_32.c __save_processor_state calls read_cr4()
only a i486 CPU doesn't have the CR4 register. Trying to read it
produces an invalid opcode oops during suspend to disk.
Use the safe rc4 reading op instead. If the value to be written is
zero the write is skipped.
arch/x86/power/hibernate_asm_32.S
done: swapped the use of %eax and %ecx to use jecxz for
the zero test and jump over store to %cr4.
restore_image: s/%ecx/%eax/ to be consistent with done:
In addition to __save_processor_state, acpi_save_state_mem,
efi_call_phys_prelog, and efi_call_phys_epilog had checks added
(acpi restore was in assembly and already had a check for
non-zero). There were other reads and writes of CR4, but MCE and
virtualization shouldn't be executed on a i486 anyway.
Signed-off-by: David Fries <david@fries.net>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
WARNING: vmlinux.o(.text+0x118f7): Section mismatch in reference from the function construct_ioapic_table() to the function .init.text:MP_bus_info()
The function construct_ioapic_table() references
the function __init MP_bus_info().
This is often because construct_ioapic_table lacks a __init
annotation or the annotation of MP_bus_info is wrong.
construct_ioapic_table is called only from construct_default_ISA_mptable which is __init
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
WARNING: arch/x86/kernel/built-in.o(.cpuinit.text+0x1591): Section mismatch in reference from the function init_amd() to the function .init.text:check_enable_amd_mmconf_dmi()
The function __cpuinit init_amd() references
a function __init check_enable_amd_mmconf_dmi().
If check_enable_amd_mmconf_dmi is only used by init_amd then
annotate check_enable_amd_mmconf_dmi with a matching annotation.
check_enable_amd_mmconf_dmi is only called from init_amd which is __cpuinit
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
WARNING: arch/x86/kernel/built-in.o(.cpuinit.text+0x1fe7): Section mismatch in reference from the function MP_processor_info() to the variable .init.data:x86_quirks
The function __cpuinit MP_processor_info() references
a variable __initdata x86_quirks.
If x86_quirks is only used by MP_processor_info then
annotate x86_quirks with a matching annotation.
MP_processor_info uses x86_quirks which is __init and is used only from
smp_read_mpc and construct_default_ISA_mptable which are __init
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
WARNING: vmlinux.o(.text+0x7950): Section mismatch in reference from the function native_calibrate_tsc() to the function .init.text:tsc_read_refs()
The function native_calibrate_tsc() references
the function __init tsc_read_refs().
This is often because native_calibrate_tsc lacks a __init
annotation or the annotation of tsc_read_refs is wrong.
tsc_read_refs is called from native_calibrate_tsc which is not __init
and native_calibrate_tsc cannot be marked __init
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use the generic compat_sys_old_readdir instead of the powerpc one which
is almost the same except for the almost complete lack of error
handling.
Note that we can't just use SYSCALL() in systbl.h because the native
syscall is named old_readdir, not sys_old_readdir.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit 163f6876f5 missed one, resulting in
the following compile error:
AS arch/powerpc/kernel/misc_32.o
arch/powerpc/kernel/misc_32.S: Assembler messages:
arch/powerpc/kernel/misc_32.S:902: Error: unsupported relocation against KEXEC_CONTROL_CODE_SIZE
make[2]: *** [arch/powerpc/kernel/misc_32.o] Error 1
make[1]: *** [arch/powerpc/kernel] Error 2
make: *** [vmlinux] Error 2
I grepped arch/ and found no further instances.
Signed-off-by: Paul Collins <paul@ondioline.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Doing some various "make randconfig", I came across an error when
CONFIG_BUG was not set:
arch/powerpc/kernel/module.c: In function 'module_find_bug':
arch/powerpc/kernel/module.c:111: error: increment of pointer to unknown structure
arch/powerpc/kernel/module.c:111: error: arithmetic on pointer to an incomplete type
arch/powerpc/kernel/module.c:112: error: dereferencing pointer to incomplete type
Looking further into this, I found that module_find_bug, defined in
powerpc arch code, is not called anywhere, so this just removes it.
There is a static module_find_bug in lib/bug.c but that is a separate issue.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a field in lparcfg output to indicate whether the kernel is
running on a dedicated or shared memory lpar. Added fields to show
the paging space pool IDs and the CMO page size.
Submitted-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If the firmware page size used for collaborative memory overcommit
is 4k, but the kernel is using 64k pages, the page loaning is currently
broken as it only marks the first 4k page of each 64k page as loaned.
This fixes this to iterate through each 4k page and mark them all as
loaned/active.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
During platform setup, save off the primary/secondary paging space
pool IDs and the page size. Added accessors in hvcall.h for these
variables. This is needed for a subsequent fix.
Submitted-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A small bogon sneaked into the ppc64 lockdep support. A test is
branching slightly off causing a clobbered register value to
overwrite the irq state under some circumstances.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The intent of "flush_tlbs" is to invalidate all TLB entries by doing a
TLB invalidate instruction for all pages in the address range 0 to
0x00400000. A loop counter is set up at the high value and
decremented by page size. However, the loop is only done once as the
sense of the conditional branch at the loop end does not match the
setup/decrement. This fixes it to do the whole range by correcting
the branch condition.
Signed-off-by: Rocky Craig <rocky.craig@hp.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When we fork, init_new_context() improperly resets the vdso_base
of the new context to 0. That means that the new process loses
access to the vdso for signal trampolines.
The initialization should be unnecessary anyway as the context
on a fresh mm should be 0 in the first place and binfmt_elf
will initialize that value for a newly loaded process.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (32 commits)
x86: add MAP_STACK mmap flag
x86: fix section mismatch warning - spp_getpage()
x86: change init_gdt to update the gdt via write_gdt, rather than a direct write.
x86-64: fix overlap of modules and fixmap areas
x86, geode-mfgpt: check IRQ before using MFGPT as clocksource
x86, acpi: cleanup, temp_stack is used only when CONFIG_SMP is set
x86: fix spin_is_contended()
x86, nmi: clean UP NMI watchdog failure message
x86, NMI: fix watchdog failure message
x86: fix /proc/meminfo DirectMap
x86: fix readb() et al compile error with gcc-3.2.3
arch/x86/Kconfig: clean up, experimental adjustement
x86: invalidate caches before going into suspend
x86, perfctr: don't use CCCR_OVF_PMI1 on Pentium 4Ds
x86, AMD IOMMU: initialize dma_ops after sysfs registration
x86m AMD IOMMU: cleanup: replace LOW_U32 macro with generic lower_32_bits
x86, AMD IOMMU: initialize device table properly
x86, AMD IOMMU: use status bit instead of memory write-back for completion wait
x86: silence mmconfig printk
x86, msr: fix NULL pointer deref due to msr_open on nonexistent CPUs
...
* master.kernel.org:/home/rmk/linux-2.6-arm: (38 commits)
[ARM] 5191/1: ARM: remove CVS keywords
[ARM] pxafb: fix the warning of incorrect lccr when lcd_conn is specified
[ARM] pxafb: add flag to specify output format on LDD pins when base is RGBT16
[ARM] pxafb: fix the incorrect configuration of GPIO77 as ACBIAS for TFT LCD
[ARM] 5198/1: PalmTX: PCMCIA fixes
[ARM] Fix a pile of broken watchdog drivers
[ARM] update mach-types
[ARM] 5196/1: fix inline asm constraints for preload
[ARM] 5194/1: update .gitignore
[ARM] add proc-macros.S include to proc-arm940 and proc-arm946
[ARM] 5192/1: ARM TLB: add v7wbi_{possible,always}_flags to {possible,always}_tlb_flags
[ARM] 5193/1: Wire up missing syscalls
[ARM] traps: don't call undef hook functions with spinlock held
[ARM] 5183/2: Provide Poodle LoCoMo GPIO names
[ARM] dma-mapping: provide sync_range APIs
[ARM] dma-mapping: improve type-safeness of DMA translations
[ARM] Kirkwood: instantiate the orion_spi driver in the platform code
[ARM] prevent crashing when too much RAM installed
[ARM] Kirkwood: Instantiate mv_xor driver
[ARM] Orion: Instantiate mv_xor driver for 5182
...
This patch removes CVS keywords that weren't updated for a long time.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Another fix of inconsistent shift of the LCD_BIAS_ACTIVE_* and
LCD_PCLK_EDGE_* is also included.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With gcc 4.3 and later, a pointer that has already been dereferenced is
assumed not to be null since it should have caused a segmentation fault
otherwise, hence any subsequent test against NULL is optimized away.
Current inline asm constraint used in the implementation of prefetch()
makes gcc believe that the pointer is dereferenced even though the PLD
instruction does not load any data and does not cause a segmentation
fault on null pointers, which causes all sorts of interesting results
when reaching the end of a linked lists for example.
Let's use a better constraint to properly represent the actual usage of
the pointer value.
Problem reported by Chris Steel.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (33 commits)
Blackfin arch: hook up some missing new system calls
Blackfin arch: fix missing digit in SCLK range checking
Blackfin arch: do not muck with the UART during boot -- let the serial driver worry about it
Blackfin arch: clear EMAC_SYSTAT during IRQ init rather than early head.S as we dont need it setup that early
Blackfin arch: use %pF when printing out the double fault address so we get symbol names
Blackfin arch: add support for the BlackStamp board
Blackfin arch: Allow ins functions to have a low latency version
Blackfin arch: Print out doublefault addresses, so debug can occur
Blackfin arch: shuffle related prototypes together -- no functional changes
Blackfin arch: move fixed code defines into fixed_code.h as very few things actually need to know these details
Blackfin arch: mark some functions as __init as they are only called from __init functions
Blackfin arch: delete dead prototypes
Blackfin arch: cleanup cache lock code
Blackfin arch: workaround SIC_IWR1 reset bug, by keeping MDMA0/1 always enabled in SIC_IWR1.
Blackfin arch: Fix bug - when expanding the trace buffer, it does not print out the decoded instruction.
Blackfin arch: Fix Bug - System with EMAC driver enabled - Core not idling
Blackfin arch: delete unused cache functions
Blackfin arch: convert L2 defines to be the same as the L1 defines
Blackfin arch: unify the duplicated portions of __start and split mach-specific pieces into _mach_early_start where they will be easier to trim over time
Blackfin arch: add asm/thread_info.h for THREAD_SIZE define
...
* 'release-2.6.27' of git://git.kernel.org/pub/scm/linux/kernel/git/ak/linux-acpi-2.6:
cpuidle: Make ladder governor honor latency requirements fully
cpuidle: Menu governor fix wrong usage of measured_us
cpuidle: Do not use poll_idle unless user asks for it
x86: Fix ioremap off by one BUG
WARNING: vmlinux.o(.text+0x17a3e): Section mismatch in reference from the function set_pte_vaddr_pud() to the function .init.text:spp_getpage()
The function set_pte_vaddr_pud() references
the function __init spp_getpage().
This is often because set_pte_vaddr_pud lacks a __init
annotation or the annotation of spp_getpage is wrong.
spp_getpage is called from __init (__init_extra_mapping) and
non __init (set_pte_vaddr_pud) functions, so it can't be __init.
Unfortunately it calls alloc_bootmem_pages which is __init,
but does it only when bootmem allocator is available (after_bootmem == 0).
So annotate it accordingly.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: H. Peter Anvin <hpa@zytor.com>
By writing directly, a memory access violation can occur whilst
hotplugging a CPU if the entry was previously marked read-only.
Signed-off-by: Alex Nixon <alex.nixon@citrix.com>
Cc: Jeremy Fitzhardinge <Jeremy.Fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Sam Ravnborg did the build-test that the direct header file move works,
I'm just committing it.
This is a pure move:
mkdir arch/alpha/include
git mv include/asm-alpha arch/alpha/include/asm
with no other changes.
Requested-and-tested-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jean Delvare's machine triggered this BUG
acpi_os_map_memory phys ffff0000 size 65535
------------[ cut here ]------------
kernel BUG at arch/x86/mm/pat.c:233!
with ACPI in the backtrace.
Adding some debugging output showed that ACPI calls
acpi_os_map_memory phys ffff0000 size 65535
And ioremap/PAT does this check in 32bit, so addr+size wraps and the BUG
in reserve_memtype() triggers incorrectly.
BUG_ON(start >= end); /* end is exclusive */
But reserve_memtype already uses u64:
int reserve_memtype(u64 start, u64 end,
so the 32bit truncation must happen in the caller. Presumably in ioremap
when it passes this information to reserve_memtype().
This patch does this computation in 64bit.
http://bugzilla.kernel.org/show_bug.cgi?id=11346
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Fix coding style of traps_64.c with improvements suggested by Ingo.
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Ftrace depends on some processor state that we destroyed during kexec and
restored by restore_processor_state(). So save_processor_state() and
restore_processor_state() are moved into machine_kexec() and ftrace is
restored after restore_processor_state().
Signed-off-by: Huang Ying <ying.huang@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kexec/Kexec-jump require code size in control page is less than
PAGE_SIZE/2. This patch add link-time checking for this.
ASSERT() of ld link script is used as the link-time checking mechanism.
[akpm@linux-foundation.org: build fix]
Signed-off-by: Huang Ying <ying.huang@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rename KEXEC_CONTROL_CODE_SIZE to KEXEC_CONTROL_PAGE_SIZE, because control
page is used for not only code on some platform. For example in kexec
jump, it is used for data and stack too.
[akpm@linux-foundation.org: unbreak powerpc and arm, finish conversion]
Signed-off-by: Huang Ying <ying.huang@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Plus add a build time check so this doesn't go unnoticed again.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Adds a simple IRQ autodetection to the AMD Geode MFGPT driver, and more
importantly, adds some checks, if IRQs can actually be received on the
chosen line. This fixes cases where MFGPT is selected as clocksource
though not producing any ticks, so the kernel simply starves during
boot.
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Cc: Andres Salomon <dilinger@debian.org>
Cc: linux-geode@bombadil.infradead.org
Cc: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
