Subsystem requests don't have or need a valid adapter index.
The adapter index is already checked further on, before it is used to index
the adapters array. (Reverts 4a122c10f)
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Work towards moving the function into alsa common header.
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The loader API has been revised so that OS specific data is kept
local to hpidspcd.c, and the public API is unchanged across OSes.
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some cobranet control data would not fit in an original HPI message.
Now that HPI is able to transfer larger messages, this special handling
is no longer required.
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allow for up to 256 bytes of extra data on top of standard hpi
request and response sizes.
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Having a 'request message' makes more sense than a 'message message'
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch fixes non-working indep-HP control on VT1708* codecs.
The problems are that via_independent_hp_put() wasn't fixed to follow
the recent change of three HP paths, and hp_indep_path didn't contain
the amp nids of mixer elements.
Together with the fixes, a few code clean-ups are done.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch changes the behavior of independent-HP enum switch. Now
instead of returning a busy error, the driver switches dynamically the
stream of the HP (and shared) DACs according to the current mode.
The logic is similar like the dual-mic ADC switch, but a bit more
complicated because of the presence of shared DAC.
Together with the change, a mutex is introduced to protect against the
possible races for the indep-HP mode setting.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the dynamic control of analog-loopback for VIA codecs.
When the loopback is enabled, the inputs from line-ins and mics are
mixed with the front DAC, and sent to the front outputs. The very same
input is routed to the headhpones and speakers in loopback mode.
However, since the loopback mix can't take other than the front DAC,
there is no longer individual volume controls for headphones and
speakers. Once when the loopback control is off, these volumes take
effect.
Since the individual volumes are more desired in general use caess, the
loopback mode is set to off as default for now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit dd203fa97b (ALSA: virtuoso: remove non-working controls on
Essence ST Deluxe) made it impossible to adjust the volume after the
driver initialized it to muted.
Ensure that those DACs that can be accessed with I2C are initialized
to the same volume that is the reset default of the DAC without I2C.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: 2.6.38+ <stable@kernel.org>
BugLink: https://bugs.launchpad.net/bugs/774895
The original reporter states that his volume keys do not change the
desired Master and PCM mixer elements together, so apply the hp+mute led
quirk for his PCI SSID.
Reported-by: Jeffrey Finkelstein
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
During the rewrite, the check of spec->need_dac_fix and the corresponding
num_dacs change was dropped from the channel-mode control.
This patch re-adds it, and also enables need_dac_fix for ALC880 as default,
as this feature was originally introduced to fix h/w bugs of this chip.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit is a fix up for commit acfa634f.
commit acfa634f7e
Author: Takashi Iwai <tiwai@suse.de>
Date: Tue Jul 12 17:27:46 2011 +0200
ALSA: hda - Add Kconfig for the default buffer size
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a Kconfig entry to specify the default buffer size.
Distros using PulseAudio can choose a larger value here.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
VT1718S and co have a secret connection from DAC to AA-mix, which
doesn't appear in the connection list obtained from the h/w.
Currently the driver fixes the connection index locally at init, but
now we can expose it statically via snd_hda_override_connections()
so that this conection can be checked better by the parser in future.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the codec proc outputs, read the raw connections instead of the
cached connection list, i.e. proc files contain only raw values.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a function to add/modify the connection-list cache entry.
It'll be useful to fix a buggy hardware result.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some machines seem to use EAPD control of the unused pin for controlling
the overall EAPD. Since the driver currently doesn't check the EAPD of
unused pins, the EAPD isn't enabled. For avoiding such a problem, turn
all extra EAPDs on as default.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For smart51 pins, we need to preserve the input pin-control bits at
auto-mute controls instead of overwriting zero or pin-out-only.
Otherwise the VREF won't be set properly when smart51 is disabled
again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When Independent-HP mode is changed for VIA, the driver needs to
re-issue the auto-mute check so that the line-out pins are set properly
without influence of HP pin state.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the line-jack is plugged/unplugged, the driver must check also
the headphone jack state in addition to the line-out jack. Currently
it checks only the line-out state and ignores the headphone.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of checking the model quirk, use a fixup table for workaround
of 44kHz-fixed PCM for Lenovo IdeaPad with ALC269.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It's harmless but annyoing.
sound/pci/hda/patch_realtek.c: In function ‘alc_cap_getput_caller’:
sound/pci/hda/patch_realtek.c:2722:9: warning: ‘err’ may be used uninitialized in this function
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now all alc*_parse_auto_config() do almost same thing except for the
NID list to ignore and the PINs for SSID-check, we can merge all these
to a single function. A good amount of code reduction.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
One more code reduction. This codec has less DACs, thus the wiring
to DAC can't be filled uniquely for all output pins, i.e. some outputs
share the same volume control.
Except for that, all seems working fine.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge more auto-parser code in patch_realtek.c, now for ALC861.
The topology of this codec is pretty simple, and can be parsed well
by the current starndard parser.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
query_amp_caps() may return non-zero if the amp cap isn't supported
by the codec. Thus one needs to check widget-caps first, then check
the corresponding amp-caps.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A regression fix from commit 21268961d3
ALSA: hda - More flexible dynamic-ADC switching for Realtek codecs
The auto-mic wasn't detected properly when no ADC-switch is needed.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For VT2002P, VT1802 and VT1812 codecs, to create Independent HP
control.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For VT2002P, VT1802 and VT1812 codecs, there're only two DACs. So smart51
control shouldn't be created.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For VT2002P, VT1802 and VT1812 codecs, the original activate_output_path()
function can't initialize output and hp path correctly, since mixers connected to
output pin widgets are not considered. So modify the activate_output_path()
function to satisify this kind of codec.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Put the all static quirk codes out of patch_realtek.c, split into the
file for each codec model. For controlling the build of quirk codes,
a new Kconfig, CONFIG_SND_HDA_ENABLE_REALTEK_QUIRKS is introduced.
By setting this off, all quirk codes won't be built, thus you can save
lots of memory.
The codes in patch_realtek.c are also shuffled and more comments are
given, but the contents aren't changed. This is just a refactoring.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch changes the auto-parser and the auto-mic handling codes to
allow more flexible dynamic ADC-switching with Realtek codecs.
In the new code, the following strategy is taken:
- When a cap-src can't handle all input-sources, either skip it, or
switch to the ADC-switching mode. In ADC-switching mode, like the
former dual-ADC mode for ALC275, it changes ADC on the fly according
to the current input source.
- When auto-mic is possible, always assign imux. If the mic pins are
set statically via a quirk, rebuild imux according to the pins.
In the auto-mic mode, the driver always changes the imux (although
the imux isn't exposed as a mixer element).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of assigning each default hda_pcm_stream pointers, do NULL-checks
and assign default values in alc_build_pcms().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The only different implmentation was alc880_auto_init_input_src(),
and now it covers this variant, and we can use the single function
for all codecs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now with the new code for looking for ADCs and MUXs, we can replace
the whole ADC assignment with the parsed results.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
All alc*_auto_init_analog_input() calls are identical, so let's use
the same function more clearly without aliases.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Parse ADCs and cap-srcs in alc_auto_create_input_ctls() by itself
instead of passing explicitly from the caller. By this change, all
alc*_auto_create_input_ctls() can be unified to the same calls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the same common code for auto-parsing the output paths and their
initializations, based on the existing ALC662 code, which is smarter
than the old ALC880/2 code.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When multiple inputs are present on the mixer widget (typically a DAC
and a loopback), mute/unmute both inputs with the corresponding mixer
element.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In alc662_auto_fill_dac_nids(), the HP and speaker DACs aren't parsed
when the corresponding pins aren't fixed with single DACs.
Now check these DACs even for non-fixed pins.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the dual-adc switching mode is active in Realtek auto-parser,
we need to couple all ADCs as a single capture-volume. Currently, the
volume control changes only the first ADC, thus others may remain silent.
This patch fixes the problem.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the support of ALC269VC codec.
Also delete the unnecessary codec_variant type enum list:
now only three variants (ALC269VA ALC269VB ALC269VC) are needed.
In addition, added some aliases:
- Add ALC269VB alias name ALC277
- Add ALC269VC alias name ALC259 ALC281X
- Add ALC269VC for Lenovo device 0x21f3 name ALC3202
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since we now route the front DAC via aa-mix widget, adding the aa-mix
to surrounds will result in a mix-up of both front and surround PCM
signals. For avoiding this, the aa-mix routes have to be disabled
for surround paths.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the individual DAC is available for the headphone output, the driver
should create the DAC for its volume control.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For VT1718S, the multi-channel path should be like following:
DAC 0-->Mixer 9(index 5)-->Mixer 0(index 1)-->Front Pin;
DAC 1-->Mixer 1(index 0)-->Surround Pin;
DAC 2-->C/LFE Pin;
DAC 3-->Mixer 2(index 0)-->Side Pin;
But current code built Surround and Side path through index 1 of
Mixer 1 and 2. So Adjusting Surround and Side channel amplifier is
invalid. This patch fixes the issue.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For VT1718S, Mixer 9 doesn't expose the connection to DAC 0. So when
building up a 'PCM Playback' amplifier control, it will fail since
getting DAC 0 index of Mixer 9 returned -1. So I added a dac_mixer_idx
to indicated the actual index of DAC 0 to Mixer 9. Following is the
patch and next mail is another.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Unmute DAC on front speaker path when Independent HP is enabled.
When to enable Independent HP, the front speaker won't output any sound
for VT1708, VT1708B, VT1708S and VT1702.
I find the via_independent_hp_put() routine will mute DAC 0 path in Mixer 0.
For these codecs, when using Independent HP, there could have two
independent streams, one is from DAC0-->Mixer0-->Front Pin, the other is
from DAC3-->GainSW3-->Side Pin.
So I added a check for DAC-->Mixer path in activate_output_path().
If current path is DAC-->Mixer, no need to mute DAC index in Mixer.
In fact, to change connection of Headphone pin or Mux connected with HP
is enough.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the re-implementation of Independent-HP mode in the
case where the DAC is shared between HP and side-channel streams.
Now the driver tries to parse the output-path using the pre-parsed
side-channel DAC for the independent HP output, too.
When a playback PCM stream is opened with this shared mode, the
Independent-HP mixer switch can't be changed for avoiding the conflict,
thus it returns -EBUSY error.
One remaining unintuitive issue is that the DAC volume is still
controlled as "Side" volume although it's shared by both independent-HP
and side streams.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The char can be unsigned on some architectures. Since the code checks
the negative values, they should be declared as signed char explicitly.
sound/pci/rme9652/hdspm.c:5449: warning: comparison is always false due to limited range of data type
sound/pci/rme9652/hdspm.c:5462: warning: comparison is always false due to limited range of data type
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix the wrongly converted short values:
sound/pci/cs5535audio/cs5535audio_pcm.c:152: warning: large integer implicitly truncated to unsigned type
sound/pci/cs5535audio/cs5535audio_pcm.c:160: warning: large integer implicitly truncated to unsigned type
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I noticed that the last character of the ELD monitor name is lost,
this fixes the issue.
This fix should be confirming to the HDA spec, and works together with
the DRM part of the ELD patch.
The HDA spec does not mention that Monitor_Name_String is an '\0'
ending string, and it allows NML to be 1, which is only valid when MNL
does not count the possible ending '\0'.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move codec init verb which is only applicatable for VT1708.
I've found the root cause that jack plugged in can't be detected.
The verb in vt1708_init_verbs is used to power down jack detect circuit.
This verb is only applicable to VT1708. vt1708 didn't implement jack
detect function in hardware, so we should shut down this function to
avoid noise. But for other codecs, hardware implement jack detect
function. If sending this verb during initialization, jack detect will
be invalid. So I move this verb from via_parse_auto_config() to
patch_vt1708().
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Create snd_hda_get_conn_index() helper function for obtaining the
connection index of the widget. Replaced the similar codes used in
several codec-drivers with this common helper.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix a issue to enable unsolicited response to line-out pins.
Signed-off-by: Lydia Wang <lydiawang@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since we're not using the new auto parser as a fallback yet,
add it manually as a quirk.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Conexant ID 506c was found on Acer Aspire 3830TG. As users report
no playback, sending to stable should be safe.
Cc: stable@kernel.org
BugLink: https://bugs.launchpad.net/bugs/783582
Reported-by: andROOM
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use static inline for dummy function to fix the warnings like below
sound/pci/hda/patch_sigmatel.c: In function ‘stac92xx_init’:
sound/pci/hda/patch_sigmatel.c:4387:3: warning: statement with no effect
sound/pci/hda/patch_sigmatel.c: In function ‘stac92xx_resume’:
sound/pci/hda/patch_sigmatel.c:4927:3: warning: statement with no effect
Signed-off-by: Takashi Iwai <tiwai@suse.de>
More similar fixes like previous commits: handle the exceptional case
like ALC267 where no volume amp is found in ADC widget but in the
capsrc widget instead.
Also minor checks for avoiding possible erros: no connection-select
when the pin has a single selection, and add beep verbs only when the
0x1d is used for beep.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALC259 seems to provide an invalid widget capability for the input-src
selector widget. The widget shows the input-amp while it's a selector,
and this confuses the current ALC882 initialization code that is used
for ALC259, too. For fixing this, check the amp capability and handle
the connection selection individually.
Also, ALC259 has no mute bit in DAC volume, so we need to initialize
it as ZERO instead of MUTE.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALC269 and compatible codecs have the output volume in DACs, thus we
can't use the ALC880's code as is. Fixed by checking the amp caps and
picking up the right widget for initialization.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Look through the known NIDs that may have EAPD capabilities and turn
on/off them appropriately instead of checking the individual vendor ids.
This will also avoid the forgotten entries of newly added codec ids
in future.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix the regression introduced by the commit
1f0f4b8036
ALSA: hda - Reduce static init verbs for Realtek auto-parsers
The input amps of mixer widgets should be unmuted as default (as
usually they have no assigned mixer switches).
More fixes in this commit are, however, for ALC260: ALC260 codec can
have multiple output mixers connnected to a single DAC althouh the
driver didn't pick up them properly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some Realtek codecs have the output pins hardwired with certain DACs.
These DACs have to be assigned at first and assign the rest for
multi-DAC pins so that all DACs can be assigned properly.
Without such an optimization, speaker outputs may be assigned to the
same DAC as the headphone or others.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In alc_auto_add_multi_channel_mode(), when the primary HP workaround
is enabled, it re-initializes the DAC list but calls alc662's function
in a fixed way. This isn't pretty suitable for other codecs, of course.
Now we call it with fill_dac function pointer so that the proper
function can be called at that point.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of using fixed init verbs, initialize DACs, ADCs and mixers
more dynamically for Realtek auto-parsers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new helper function snd_hda_get_conn_list().
Unlike snd_hda_get_connections(), this function doesn't copy the
connection-list but gives the raw pointer for the cached list.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
each device has a unique mac address, which can be used to distinguish
multiple devices in the same machine. we therefore include the full mac
address in the device shortname and the last 6 bytes in the device id.
Signed-off-by: Tim Blechmann <tim@klingt.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the sound/ directory there are two files (flagged by 'make
versioncheck'); sound/pci/asihpi/asihpi.c and
sound/soc/codecs/wm8991.c that include linux/version.h although they
don't need it. This patch removes the unneeded includes.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Change alc_get_line_out_pfx() in patch_realtek.c to provide the channel
specific name and assign the index so that each caller doesn't have to
set the channel name by itself.
Also, check the multi-io case with the primary hp-out; for the multi-io
channels, assign the channel name instead of "Headphone" with indices.
This makes the mixer names more intuitive and reduces confusion.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some BIOS set up the pin config wrongly as line-out although it's
supposed to be a speaker out. In most cases, though, we can judge
the validity by checking the connection type -- when it's FIXED,
mostly it's an invalid line-out but a speaker.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Eliot Blennerhassett