BCM57810-KR link may not come up in 1G after running loopback test, so set
the relevant registers to their default values before starting KR autoneg.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix 57810-KR flow-control handling link is achieved via CL37 AN.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a problem in which PFC frames are not honored, due to incorrect link
attributes synchronization following PMF migration, and verify PFC XON is not
stuck from previous link change.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there are no nodes in the cache, nodes will be 0, so calculating
"registers / nodes" will cause division by zero.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Modified from original patch from Chris.
The sky2 driver has to have 8 byte alignment of receive buffer
on some chip versions. On architectures which don't support efficient
unaligned access this doesn't work very well. The solution is to
just copy all received packets which is what the driver already
does for small packets.
This allows the driver to be used on the Tilera TILEmpower-Gx, since
the tile architecture doesn't currently handle kernel unaligned accesses,
just userspace.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implemenation was buggy for slaves who use ndo_neigh_setup,
since the networking stack invokes the bonding device ndo entry (from
neigh_params_alloc) before any devices are enslaved, and the bonding
driver can't further delegate the call at that point in time. As a
result when bonding IPoIB devices, the neigh_cleanup hasn't been called.
Fix that by deferring the actual call into the slave ndo_neigh_setup
from the time the bonding neigh_setup is called.
Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 7d26bb103c "bonding: emit event when bonding changes MAC" didn't
take care to emit the NETDEV_CHANGEADDR event in bond_release, where bonding
actually changes the mac address (to all zeroes). As a result the neighbours
aren't deleted by the core networking code (which does so upon getting that
event).
Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
getsockopt(..., SCTP_EVENTS, ...) performs a length check and returns
an error if the user provides less bytes than the size of struct
sctp_event_subscribe.
Struct sctp_event_subscribe needs to be extended by an u8 for every
new event or notification type that is added.
This obviously makes getsockopt fail for binaries that are compiled
against an older versions of <net/sctp/user.h> which do not contain
all event types.
This patch changes getsockopt behaviour to no longer return an error
if not enough bytes are being provided by the user. Instead, it
returns as much of sctp_event_subscribe as fits into the provided buffer.
This leads to the new behavior that users see what they have been aware
of at compile time.
The setsockopt(..., SCTP_EVENTS, ...) API is already behaving like this.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes mostly, including:
* Patch series that hopefully fixes races between the freezer and request_firmware()
and request_firmware_nowait() for good, with two cleanups from Stephen Boyd on top.
* Runtime PM fix from Alan Stern preventing tasks from getting stuck indefinitely
in the runtime PM wait queue.
* Device PM QoS update from MyungJoo Ham introducing a new variant of
pm_qos_update_request() allowing the callers to specify a timeout.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQIcBAABAgAGBQJPdmPZAAoJEKhOf7ml8uNsvcgQAIKBya3ESVg2PbB1riIRJ0M5
3R5ntbQ0sxa631lIoipZLP6HeN2fgTcfTqhHpr9/dtt80Zh/HbNWee4XEmkJvGOK
UuG/Vzg2IJA2LKYbRDEALm9GwvlG8ylIrz1mWOSt77K+seyjnvCyfQsoVd5S/+sz
bzDCwIJlV/lvtynvAMfaZ+O75XW1uYRJ6a1ABviEU4o+J7OC9UCp0h/b9c1WZqDJ
1X0pBU0/28ZFnYnK+zuAqwJg7pua/HrC0nT/pQTRSZ0kXAgt7uuqIlpVz9HXiqzu
TVbu3uW6FPWT0TP/iFmKMA1eiQJHLXgshECaccVOoMzIG/pqYTNbfu9BzEho3tL9
w716ruo1JoythvnlIz4j8R2RtiE8SxTzCqGm4OHcie72VUSqduIhWgRyZOFhebUo
xqiUSN2cyYUf9SJoeg0TSmQdutoa7vnswZgq4qjlOz39OPxHrwAe5ROXIBwoHvnz
akmBtnabyNVsRiLe9eIH5N5C9TxHDgZwS70SMYqo1D09Qo+NTUtvSVgC/NiIjhXb
yY3UliDqGlkUhHJ+8ydntNb39VU4L1MO0IGzEvmvfXvSIcXavGkkmd9RV9yytLEK
1ujq99NHITzxyuF2+bNGpPQVEVH3sQgAv/doFTiEZiUHIIAy5Fmy/+ipcurslXLm
urlq4RLG+JXgPjw4XO14
=ligR
-----END PGP SIGNATURE-----
Merge tag 'pm-for-3.4-part-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
- Patch series that hopefully fixes races between the freezer and
request_firmware() and request_firmware_nowait() for good, with two
cleanups from Stephen Boyd on top.
- Runtime PM fix from Alan Stern preventing tasks from getting stuck
indefinitely in the runtime PM wait queue.
- Device PM QoS update from MyungJoo Ham introducing a new variant of
pm_qos_update_request() allowing the callers to specify a timeout.
* tag 'pm-for-3.4-part-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / QoS: add pm_qos_update_request_timeout() API
firmware_class: Move request_firmware_nowait() to workqueues
firmware_class: Reorganize fw_create_instance()
PM / Sleep: Mitigate race between the freezer and request_firmware()
PM / Sleep: Move disabling of usermode helpers to the freezer
PM / Hibernate: Disable usermode helpers right before freezing tasks
firmware_class: Do not warn that system is not ready from async loads
firmware_class: Split _request_firmware() into three functions, v2
firmware_class: Rework usermodehelper check
PM / Runtime: don't forget to wake up waitqueue on failure
Several clocks are missing clockdomains. This can cause problems with
the hwmod and power management code. Fill these in.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Matt Porter <mporter@ti.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
All DPLLs except USB are in ALWON powerdomain. Make sure the
clkdm/pwrdm for USB DPLL (l3init) is turned on before attempting
a DPLL relock. So, mark the database accordingly.
Without this fix, it was seen that DPLL relock fails while testing
relock in a loop of USB DPLL.
Cc: Nishanth Menon <nm@ti.com>
Tested-by: Ameya Palande <ameya.palande@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit b1cbdb00d ("OMAP: clockdomain: Wait for powerdomain to be ON
when using clockdomain force wakeup") was assuming that
pwrdm_state_switch() does wait for the powerdomain transition which is
not the case. The missing wait for the powerdomain transition
violates the sequence which the hardware expects, which causes power
management failures on some devices.
Fix this API by adding the pwrdm_wait_transition().
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
[paul@pwsan.com: added some more details in the commit log]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
When Tegra30 support was added to the Tegra GPIO driver, a few places
which iterated over all banks were not converted to use the variable
tegra_gpio_bank_count rather than hard-coding the bank count. Fix this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Tegra20 and Tegra30 share the same register layout within registers, but
the addresses of the registers is a little different. Fix the driver to
cope with this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Merge common_audit_data cleanup patches from Eric Paris.
This is really too late, but it's a long-overdue cleanup of the costly
wrapper functions for the security layer.
The "struct common_audit_data" is used all over in critical paths,
allocated and initialized on the stack. And used to be much too large,
causing not only unnecessarily big stack frames but the clearing of the
(mostly useless) data was also very visible in profiles.
As a particular example, in one microbenchmark for just doing "stat()"
over files a lot, selinux_inode_permission() used 7% of the CPU time.
That's despite the fact that it doesn't actually *do* anything: it is
just a helper wrapper function in the selinux security layer.
This patch-series shrinks "struct common_audit_data" sufficiently that
code generation for these kinds of wrapper functions is improved
noticeably, and we spend much less time just initializing data that we
will never use.
The functions still get called all the time, and it still shows up at
3.5+% in my microbenchmark, but it's quite a bit lower down the list,
and much less noticeable.
* Emailed patches from Eric Paris <eparis@redhat.com>:
lsm_audit: don't specify the audit pre/post callbacks in 'struct common_audit_data'
SELinux: do not allocate stack space for AVC data unless needed
SELinux: remove avd from slow_avc_audit()
SELinux: remove avd from selinux_audit_data
LSM: shrink the common_audit_data data union
LSM: shrink sizeof LSM specific portion of common_audit_data
since a high proportion of chips have no register 0 so the normal
failure is that we end up doing a bit of extra I/O.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=i2aW
-----END PGP SIGNATURE-----
Merge tag 'regmap-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull a single regmap fix from Mark Brown:
"A simple bug that's been lurking for a while but not terribly visible
since a high proportion of chips have no register 0 so the normal
failure is that we end up doing a bit of extra I/O."
* tag 'regmap-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: rbtree: Fix register default look-up in sync
A bunch of smallish fixes that came up during the merge window as
things got more testing - even more fixes from Axel, a fix for error
handling in more complex systems using -EPROBE_DEFER and a couple of
small fixes for the new dummy regulators.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=h5VJ
-----END PGP SIGNATURE-----
Merge tag 'regulator-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A bunch of smallish fixes that came up during the merge window as
things got more testing - even more fixes from Axel, a fix for error
handling in more complex systems using -EPROBE_DEFER and a couple of
small fixes for the new dummy regulators."
* tag 'regulator-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: Remove non-existent parameter from fixed-helper.c kernel doc
regulator: Fix setting new voltage in s5m8767_set_voltage
regulator: fix sysfs name collision between dummy and fixed dummy regulator
regulator: Fix deadlock on removal of regulators with supplies
regulator: Fix comments in include/linux/regulator/machine.h
regulator: Only update [LDOx|DCx]_HIB_MODE bits in wm8350_[ldo|dcdc]_set_suspend_disable
regulator: Fix setting low power mode for wm831x aldo
regulator: Return microamps in wm8350_isink_get_current
regulator: wm8350: Fix the logic to choose best current limit setting
regulator: wm831x-isink: Fix the logic to choose best current limit setting
regulator: wm831x-dcdc: Fix the logic to choose best current limit setting
regulator: anatop: patching to device-tree property "reg".
regulator: Do proper shift to set correct bit for DC[2|5]_HIB_MODE setting
regulator: Fix restoring pmic.dcdcx_hib_mode settings in wm8350_dcdc_set_suspend_enable
regulator: Fix unbalanced lock/unlock in mc13892_regulator_probe error path
regulator: Fix set and get current limit for wm831x_buckv
regulator: tps6586x: Fix list minimal voltage setting for LDO0
This fixes the CPUFREQ dependency for regarding EXYNOS SoCs
such as EXYNOS4210, EXYNOS4X12 and EXYNOS5250. Its cpufreq
driver should be built with selection of SoC arch part.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Pull x86 fixes from Ingo Molnar.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, kvm: Call restore_sched_clock_state() only after %gs is initialized
x86: Use -mno-avx when available
x86: Remove the ancient and deprecated disable_hlt() and enable_hlt() facility
x86: Preserve lazy irq disable semantics in fixup_irqs()
Because of the inclusion of skeleton.dtsi, the memory node is
named "memory" we where not modifying the already included one
but creating a new one. It caused bad memory node detection during
early_init_dt_scan_memory() so we modify them.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: devicetree-discuss@lists.ozlabs.org
SPI chip select pins have to be checked by gpio_is_valid().
The USB host overcurrent_pin checking was missing.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Compilation error in case of non-DT configuration without this
of.h header file.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Add comments to NAND "gpios" property to make it clearer.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Change number of ports to 3 for newer SoCs. Modify pdata structure
and ohci-at91 code that was dealing with ports information and check
of port indexes.
Several coding style errors have been addresses as the patch was touching
affected lines of code and was producing errors while run through
checkpatch.pl.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
The DT information are filled in a pdata structure and then passed on
to the usual check code of the probe function. Thus we do not need to
redo the gpio checking and irq configuration in the DT-related code.
On the other hand, we setup GPIO direction in driver for vbus and
overcurrent. It will be useful when moving to pinctrl subsystem.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Change vbus gpio configuration in .dts files to switch to
active low configuration.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: stable <stable@vger.kernel.org>
Due to an error while handling vbus_pin_active_low in ohci-at91 driver,
the specification of this property was not good in devices/board files.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: stable <stable@vger.kernel.org> [3.2+]
The information is not properly taken into account
for {get|set}_power() functions.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org> [3.2+]
addruart cannot read from the physical address of the chipid
register, that will fail as soon as the mmu is turned on.
Fixing it to read from the physical or virtual address depending
on the mmu state also does not work, because there is a period
between head.S and exynos_map_io where the mmu is on, the uart
is mapped and used, but the chipid mapping is not yet present.
Fix addruart to use the ARM Main ID cp15 register to determine
if the core is Cortex A15 (EXYNOS5) or not (EXYNOS4).
Signed-off-by: Colin Cross <ccross@android.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=2kpn
-----END PGP SIGNATURE-----
Merge tag 'mce-fix-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull MCE fixlet from Borislav Petkov:
"One fix which makes MCE decoding much more "liberal" wrt families."
* tag 'mce-fix-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
MCE, AMD: Drop too granulary family model checks
Rename EMAC clocks to match driver expectations: both davinci_emac and
davinci_mdio drivers call clk_get(dev, NULL) so we have to provide
("davinci_emac", NULL) and ("davinci_mdio.0", NULL) clocks instead of
("davinci_emac", "emac_clk") and ("davinci_emac", "phy_clk") resp.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Tested-by: Matt Porter <mporter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
- some RAID levels didn't clear up properly if md_integrity_register
failed
- a 'check' of RAID5/RAID6 doesn't actually read any data
since a recent patch - so fix that (and mark for -stable)
- a couple of other minor bugs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=IBql
-----END PGP SIGNATURE-----
Merge tag 'md-3.4-fixes' of git://neil.brown.name/md
Pull assorted md fixes from Neil Brown:
- some RAID levels didn't clear up properly if md_integrity_register
failed
- a 'check' of RAID5/RAID6 doesn't actually read any data since a
recent patch - so fix that (and mark for -stable)
- a couple of other minor bugs.
* tag 'md-3.4-fixes' of git://neil.brown.name/md:
md/raid1,raid10: don't compare excess byte during consistency check.
md/raid5: Fix a bug about judging if the operation is syncing or replacing
md/raid1:Remove unnecessary rcu_dereference(conf->mirrors[i].rdev).
md: Avoid OOPS when reshaping raid1 to raid0
md/raid5: fix handling of bad blocks during recovery.
md/raid1: If md_integrity_register() failed,run() must free the mem
md/raid0: If md_integrity_register() fails, raid0_run() must free the mem.
md/linear: If md_integrity_register() fails, linear_run() must free the mem.
Pull ARM fixes from Russell King:
"Nothing too big here, just small fixes."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: fix more fallout from 9f97da78bf (Disintegrate asm/system.h for ARM)
ARM: fix bios32.c build warning
ARM: 7337/1: ptrace: fix ptrace_read_user for !CONFIG_MMU platforms
ARM: fix missing bug.h include in arch/arm/kernel/insn.c
ARM: sa11x0: fix build errors from DMA engine API updates
Pull Sparc fixes from David Miller:
"One build regression and one serial probe regression fix on sparc."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
serial/sunzilog: fix keyboard on SUN SPARCstation
sparc: pgtable_64: change include order
To fix:
In file included from kernel/exit.c:61:
arch/avr32/include/asm/mmu_context.h: In function 'enable_mmu':
arch/avr32/include/asm/mmu_context.h:135: error: implicit declaration of function 'nop'
It needs an include of the new file created in commit ae47394658
("Disintegrate asm/system.h for AVR32"), but since that file only
contains "nop", and since other arch already have precedent of putting
nop in asm/barrier.h we should just delete the new file and put nop in
barrier.h
Suggested-and-acked-by: David Howells <dhowells@redhat.com>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
clk_disable_unused is invoked when CONFIG_OMAP_RESET_CLOCKS=y.
Since clk_disable_unused is called as lateinitcall, there can
be more than a few workqueues executing off secondary CPU(s).
The current code does the following:
a) checks if clk is unused
b) holds lock
c) disables clk
d) unlocks
Between (a) and (b) being executed on CPU0, It is possible to
have a driver executing on CPU1 which could do a get_sync->clk_get
(and increase the use_count) of the clock which was just about
to be disabled by clk_disable_unused.
We ensure instead that the entire list traversal is protected by
the lock allowing for parent child clock traversal which could be
potentially be done by runtime operations to be safe as well.
Reported-by: Todd Poynor <toddpoynor@google.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This reverts commit d06221c061.
It turns out to trigger the "BUG_ON(!PageCompound(page))" in kfree(),
apparently because the code ends up trying to free somethng that was
never kmalloced in the first place.
BenH points out that the patch was untested and wasn't meant to go into
the upstream kernel that quickly in the first place.
Backtrace:
bios_shadow
bios_shadow_prom
nv_mask
init_io
bios_shadow
nouveau_bios_init
NVReadVgaCrtc
NVSetOwner
nouveau_card_init
nouveau_load
Reported-by: Meelis Roos <mroos@linux.ee>
Requested-by: Dave Airlie <airlied@gmail.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CLKS signal for McBSP ports can be selected from internal (PRCM) or
external (ABE_CLKS pin) source. To be able to use existing code we
need to create clock aliases consistent among OMAP2/3/4.
Based on a patch from Péter Ujfalusi <peter.ujfalusi@ti.com>;
the patch description above is his.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Péter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
The commit 996bc8aebd (mmc: sh_mobile_sdhi:
do not manage PM clocks manually) modified the sh_mobile_sdhi driver to
remove the clk_enable/clk_disable. So, we need to change
the "CLKDEV_CON_ID" to "CLKDEV_DEV_ID".
If we don't change this, we will see the following error from the driver:
sh_mobile_sdhi sh_mobile_sdhi.0: timeout waiting for hardware interrupt (CMD52)
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Commit 2a9f5a4d45 "OMAP3 clock: remove unnecessary duplicate of dpll4_m2_ck,
added for 36xx" consolidated dpll4 clock structures between 34xx and 36xx,
but left 34xx CLKSEL masks for most dpll4 related clocks, which causes
clock code to not behave correctly when booting on DM3730 with higher
(36xx only) divisors set:
[ 0.000000] WARNING: at arch/arm/mach-omap2/clkt_clksel.c:375 omap2_init_clksel_parent+0x104/0x114()
[ 0.000000] clock: dpll4_m3_ck: init parent: could not find regval 0
[ 0.000000] WARNING: at arch/arm/mach-omap2/clkt_clksel.c:194 omap2_clksel_recalc+0xd4/0xe4()
[ 0.000000] clock: Could not find fieldval 0 for clock dpll4_m3_ck parent dpll4_ck
Fix this by switching to 36xx masks, as valid divisors will be limited
by clksel_rate lists.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
If transceiver is attached to a MMC host of ES2.1 OMAP35xx, it seems
2.1.1.128 erratum doesn't apply and there is no data corruption,
probably because of different signal timing. The workaround for this
erratum disables multiblock reads, which causes dramatic loss of
performance (over 75% slower), so avoid it when transceiver is present.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
[paul@pwsan.com: edited commit message slightly]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
According to the 4430 ES2.0 TRM vX Table 3-744 "CM_EMU_CLKSTCTRL",
the emu_sys clockdomain data in mainline is incorrect.
The emu_sys clockdomain does not support the DISABLE_AUTO state, and
instead it supports the FORCE_WAKEUP state.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Will Deacon <will.deacon@arm.com>
MCA details seldom change inbetween the models of a family so don't
be too conservative and enable decoding on everything starting from
K8 onwards. Minor adjustments can come in later but most importantly,
we have some decoding infrastructure in place for upcoming models by
default.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The keyboard on my SUN SPARCstation 5 no longer worked.
The culprint was: d4e33fac24
("serial: Kill off NO_IRQ")
Fix up logic for no irq / irq so the keyboard works again.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yaniv Rosner