The issue was introduced in commit eed2a12f1e.
Signed-off-by: Franco Fichtner <franco@lastsummer.de>
Acked-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables ethtool to set the loopback mode on a given interface.
By configuring the interface in loopback mode in conjunction with a policy
route / rule, a userland application can stress the egress / ingress path
exposing the flows of the change in progress and potentially help developer(s)
understand the impact of those changes without even sending a packet out
on the network.
Following set of commands illustrates one such example -
a) ip -4 addr add 192.168.1.1/24 dev eth1
b) ip -4 rule add from all iif eth1 lookup 250
c) ip -4 route add local 0/0 dev lo proto kernel scope host table 250
d) arp -Ds 192.168.1.100 eth1
e) arp -Ds 192.168.1.200 eth1
f) sysctl -w net.ipv4.ip_nonlocal_bind=1
g) sysctl -w net.ipv4.conf.all.accept_local=1
# Assuming that the machine has 8 cores
h) taskset 000f netserver -L 192.168.1.200
i) taskset 00f0 netperf -t TCP_CRR -L 192.168.1.100 -H 192.168.1.200 -l 30
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After that all the upstream kernel drivers now use phys_id,
and the old ethtool_ops interface (phys_id) can be removed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__ethtool_set_flags() was not taking into account features set but not
user-toggleable.
Since GFLAGS returns masked dev->features, EINVAL is returned when
passed flags differ to it, and not to wanted_features.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
When physical identification of an adapter is done by toggling the
mechanism on and off through software utilizing the set_phys_id operation,
it is done with a fixed duration for both on and off states. Some drivers
may want to set a custom duration for the on/off intervals. This patch
changes the API so the return code from the driver's entry point when it
is called with ETHTOOL_ID_ACTIVE can specify the frequency at which to
cycle the on/off states, and updates the drivers that have already been
converted to use the new set_phys_id and use the synchronous method for
identifying an adapter.
The physical identification frequency set in the updated drivers is based
on how it was done prior to the introduction of set_phys_id.
Compile tested only. Also fixes a compiler warning in sfc.
v2: drivers do not return -EINVAL for ETHOOL_ID_ACTIVE
v3: fold patchset into single patch and cleanup per Ben's feedback
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Divy Le Ray <divy@chelsio.com>
Cc: Don Fry <pcnet32@frontier.com>
Cc: Jon Mason <jdmason@kudzu.us>
Cc: Solarflare linux maintainers <linux-net-drivers@solarflare.com>
Cc: Steve Hodgson <shodgson@solarflare.com>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Matt Carlson <mcarlson@broadcom.com>
Acked-by: Jon Mason <jdmason@kudzu.us>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool support to configure RX, TX and other channels. combined field
in struct ethtool_channels to reflect set of channel (RX, TX or other).
Other channel can be link interrupts, SR-IOV coordination etc.
ETHTOOL_GCHANNELS will report max and current number of RX channels,
max and current number of TX channels, max and current number of other channel
or max and current number of combined channel.
Number of channel can be modify upto max number of channel through
ETHTOOL_SCHANNELS command.
Ben Hutchings:
o define 'combined' and 'other' types. Most multiqueue drivers pair up RX and TX
queues so that most channels combine RX and TX work.
o Please could you use a kernel-doc comment to describe the structure.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When blinking for a duration set by the user, the value specified is in
seconds but it is used as the number of jiffies in the timeout after which
the Physical ID indicator is deactivated. Fix by converting the timeout
to seconds.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change is meant to prevent a possible null pointer dereference if
NETIF_F_NTUPLE is defined but the set_rx_ntuple function pointer is not.
The main motivation behind this patch is to eventually replace the ntuple
interfaces entirely with the network flow classifier interfaces. This
allows the device drivers to maintain the ntuple check internally while
using the network flow classifier interface for setting up and displaying
rules.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool ETHTOOL_PHYS_ID command runs for an arbitrarily long
period of time, holding the RTNL lock. This blocks routing updates,
device enumeration, and various important operations that one might
want to keep running while hunting for the flashing LED.
We need to drop the RTNL lock during this operation, but currently the
core implementation is a thin wrapper around a driver operation and
drivers may well depend upon holding the lock.
Define a new driver operation 'set_phys_id' with an argument that sets
the ID indicator on/off/inactive/active (the last optional, for any
driver or firmware that prefers to handle blinking asynchronously).
When this is defined, the ethtool core drops the lock while waiting
and only acquires it around calls to this operation.
Deprecate the 'phys_id' operation in favour of this. It can be
removed once all in-tree drivers are converted.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
This patch uses __copy_from_user_nocache on transmit to bypass data
cache for a performance improvement. skb_add_data_nocache and
skb_copy_to_page_nocache can be called by sendmsg functions to use
this feature, initial support is in tcp_sendmsg. This functionality is
configurable per device using ethtool.
Presumably, this feature would only be useful when the driver does
not touch the data. The feature is turned on by default if a device
indicates that it does some form of checksum offload; it is off by
default for devices that do no checksum offload or indicate no checksum
is necessary. For the former case copy-checksum is probably done
anyway, in the latter case the device is likely loopback in which case
the no cache copy is probably not beneficial.
This patch was tested using 200 instances of netperf TCP_RR with
1400 byte request and one byte reply. Platform is 16 core AMD x86.
No-cache copy disabled:
672703 tps, 97.13% utilization
50/90/99% latency:244.31 484.205 1028.41
No-cache copy enabled:
702113 tps, 96.16% utilization,
50/90/99% latency 238.56 467.56 956.955
Using 14000 byte request and response sizes demonstrate the
effects more dramatically:
No-cache copy disabled:
79571 tps, 34.34 %utlization
50/90/95% latency 1584.46 2319.59 5001.76
No-cache copy enabled:
83856 tps, 34.81% utilization
50/90/95% latency 2508.42 2622.62 2735.88
Note especially the effect on latency tail (95th percentile).
This seems to provide a nice performance improvement and is
consistent in the tests I ran. Presumably, this would provide
the greatest benfits in the presence of an application workload
stressing the cache and a lot of transmit data happening.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Issue FEAT_CHANGE notification when features are changed by
netdev_update_features(). This will allow changes made by extra constraints
on e.g. MTU change to be properly propagated like changes via ethtool.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit d5dbda2380 "ethtool: Add
support for vlan accleration.", drivers that have NETIF_F_HW_VLAN_TX,
and/or NETIF_F_HW_VLAN_RX feature, but do not allow enable/disable vlan
acceleration via ethtool set_flags, always return -EINVAL from that
function. Fix by returning -EINVAL only if requested features do not
match current settings and can not be changed by driver.
Change any driver that define ethtool->set_flags to use
ethtool_invalid_flags() to avoid similar problems in the future
(also on drivers that do not have the problem).
Tested with modified (to reproduce this bug) myri10ge driver.
Cc: stable@kernel.org # 2.6.37+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement compatibility with new hw_features for dev_disable_lro().
This is a transition path - dev_disable_lro() should be later
integrated into netdev_fix_features() after all drivers are converted.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
__ethtool_set_sg does not check if dev->ethtool_ops->set_sg is defined
which can result in a NULL pointer dereference when ethtool is used to
change SG settings for drivers without SG support.
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use discrete setting ops for not updated drivers. This will not make
them conform to full G/SFEATURES semantics, though.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement getting rx checksum state for not updated drivers.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce NETIF_F_RXCSUM to replace device-private flags for RX checksum
offload. Integrate it with ndo_fix_features.
ethtool_op_get_rx_csum() is removed altogether as nothing in-tree uses it.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces a new framework to handle device features setting.
It consists of:
- new fields in struct net_device:
+ hw_features - features that hw/driver supports toggling
+ wanted_features - features that user wants enabled, when possible
- new netdev_ops:
+ feat = ndo_fix_features(dev, feat) - API checking constraints for
enabling features or their combinations
+ ndo_set_features(dev) - API updating hardware state to match
changed dev->features
- new ethtool commands:
+ ETHTOOL_GFEATURES/ETHTOOL_SFEATURES: get/set dev->wanted_features
and trigger device reconfiguration if resulting dev->features
changed
+ ETHTOOL_GSTRINGS(ETH_SS_FEATURES): get feature bits names (meaning)
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows to enable GRO even if RX csum is disabled. GRO will not
be used for packets without hardware checksum anyway.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed for unified offloads patch.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a conflict between commit b00916b1 and a77f5db3. This patch resolves
the conflict by clearing the heap allocation in ethtool_get_regs().
Cc: stable@kernel.org
Signed-off-by: Eugene Teo <eugeneteo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quoting Ben Hutchings: we presumably won't be defining features that
can only be enabled on 64-bit architectures.
Occurences found by `grep -r` on net/, drivers/net, include/
[ Move features and vlan_features next to each other in
struct netdev, as per Eric Dumazet's suggestion -DaveM ]
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
While an interface is down, many implementations of
ethtool_ops::get_link, including the default, ethtool_op_get_link(),
will report the last link state seen while the interface was up. In
general the current physical link state is not available if the
interface is down.
Define ETHTOOL_GLINK to reflect whether the interface *and* any
physical port have a working link, and consistently return 0 when the
interface is down.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NETIF_F_HW_CSUM is a superset of NETIF_F_IP_CSUM+NETIF_F_IPV6_CSUM, but
some drivers miss the difference. Fix this and also fix UFO dependency
on checksumming offload as it makes the same mistake in assumptions.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that vlan acceleration is handled consistently regardless of usage,
it is possible to enable and disable it at will. This adds support for
Ethtool operations that change the offloading status for debugging
purposes, similar to other forms of hardware acceleration.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several other ethtool functions leave heap uncleared (potentially) by
drivers. Some interfaces appear safe (eeprom, etc), in that the sizes
are well controlled. In some situations (e.g. unchecked error conditions),
the heap will remain unchanged in areas before copying back to userspace.
Note that these are less of an issue since these all require CAP_NET_ADMIN.
Cc: stable@kernel.org
Signed-off-by: Kees Cook <kees.cook@canonical.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling ETHTOOL_GRXCLSRLALL with a large rule_cnt will allocate kernel
heap without clearing it. For the one driver (niu) that implements it,
it will leave the unused portion of heap unchanged and copy the full
contents back to userspace.
Signed-off-by: Kees Cook <kees.cook@canonical.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/core/ethtool.c: In function 'ethtool_get_regs':
net/core/ethtool.c:818:2: error: implicit declaration of function 'vmalloc'
net/core/ethtool.c:818:9: warning: assignment makes pointer from integer without a cast
net/core/ethtool.c:833:2: error: implicit declaration of function 'vfree'
Signed-off-by: David S. Miller <davem@davemloft.net>
Some NICs have huge register files which exceed the maximum heap
allocation size.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool utility does not set masks for flow parameters that are
not specified, so if both value and mask are 0 then this must be
treated as equivalent to a mask with all bits set. Currently that is
done in the only driver that implements RX n-tuple filtering, ixgbe.
Move it to the ethtool core.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be able to switch on GRO on a device, ethtool_set_gro() checks this
device provides a get_rx_csum() method.
Some devices dont provide this method, while they do support RX
checksumming.
This patch allows bonding to support GRO :
ethtool -K bond0 gro on
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct ethtool_rawip4_spec and struct ethtool_ether_spec are neither
commented nor used by any driver, so remove them. Adjust padding in
the user-visible unions that included these structures.
Fix references to struct ethtool_rawip4_spec in
ethtool_get_rx_ntuple(), which should use struct ethtool_usrip4_spec.
struct ethtool_usrip4_spec cannot hold IPv6 host addresses and there
is no separate structure that can, so remove ETH_RX_NFC_IP6 and the
reference to it in niu.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SNMP daemon uses ethtool to determine the speed of
network interfaces. This fails on Debian (and probably elsewhere)
because for security SNMP daemon runs as non-root user (snmp).
Note: A similar patch was rejected previously because of a concern about
the possibility that on some hardware querying the ethtool settings
requires access to the PHY and could slow the machine down. But the
security risk of requiring SNMP daemon (and related services)
to run as root far out weighs the risk of denial-of-service.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver name and bus address for a net_device can normally be found
through the driver model now. Instead of requiring drivers to provide
this information redundantly through the ethtool_ops::get_drvinfo
operation, use the driver model to do so if the driver does not define
the operation. Since ETHTOOL_GDRVINFO no longer requires the driver
to implement any operations, do not require net_device::ethtool_ops to
be set either.
Remove implementations of get_drvinfo and ethtool_ops that provide
only this information.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many NICs use an indirection table to map an RX flow hash value to one
of an arbitrary number of queues (not necessarily a power of 2). It
can be useful to remove some queues from this indirection table so
that they are only used for flows that are specifically filtered
there. It may also be useful to weight the mapping to account for
user processes with the same CPU-affinity as the RX interrupts.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool_op_set_flags() does not check for unsupported flags, and has
no way of doing so. This means it is not suitable for use as a
default implementation of ethtool_ops::set_flags.
Add a 'supported' parameter specifying the flags that the driver and
hardware support, validate the requested flags against this, and
change all current callers to pass this parameter.
Change some other trivial implementations of ethtool_ops::set_flags to
call ethtool_op_set_flags().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct ethtool_rxnfc was originally defined in 2.6.27 for the
ETHTOOL_{G,S}RXFH command with only the cmd, flow_type and data
fields. It was then extended in 2.6.30 to support various additional
commands. These commands should have been defined to use a new
structure, but it is too late to change that now.
Since user-space may still be using the old structure definition
for the ETHTOOL_{G,S}RXFH commands, and since they do not need the
additional fields, only copy the originally defined fields to and
from user-space.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
On a 32-bit machine, info.rule_cnt >= 0x40000000 leads to integer
overflow and the buffer may be smaller than needed. Since
ETHTOOL_GRXCLSRLALL is unprivileged, this can presumably be used for at
least denial of service.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Also added an explicit break; to avoid
a fallthrough in net/ipv4/tcp_input.c
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix coding style errors and warnings output while running checkpatch.pl
on the files net/core/ethtool.c and include/linux/ethtool.h
Signed-off-by: chavey <chavey@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds ethtool and device feature flag to allow control
of receive hashing offload.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Franco Fichtner