Adding a pair of set-get routines to dcbnl for setting the negotiation
flags of the various DCB features. Conforms to the CEE flavor of DCBX
The user sets these flags (enable, advertise, willing) for each feature
to be used by the DCBX engine. The 'get' routine returns which of the
features is enabled after the negotiation.
This patch is dependent on the following patches:
[net-next-2.6 PATCH 1/3] dcbnl: add support for ieee8021Qaz attributes
[net-next-2.6 PATCH 2/3] dcbnl: add appliction tlv handlers
[net-next-2.6 PATCH 3/3] net_dcb: add application notifiers
Signed-off-by: Shmulik Ravid <shmulikr@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding an optional DCBX capability and a pair for get-set routines for
setting the device DCBX mode. The DCBX capability is a bit field of
supported attributes. The user is expected to set the DCBX mode with a
subset of the advertised attributes.
This patch is dependent on the following patches:
[net-next-2.6 PATCH 1/3] dcbnl: add support for ieee8021Qaz attributes
[net-next-2.6 PATCH 2/3] dcbnl: add appliction tlv handlers
[net-next-2.6 PATCH 3/3] net_dcb: add application notifiers
Signed-off-by: Shmulik Ravid <shmulikr@broadcom.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DCBx applications priorities can be changed dynamically. If
application stacks are expected to keep the skb priority
consistent with the dcbx priority the stack will need to
be notified when these changes occur.
This patch adds application notifiers for the stack to register
with.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds application tlv handlers. Networking stacks
may use the application priority to set the skb priority of
their stack using the negoatiated dcbx priority.
This patch provides the dcb_{get|set}app() routines for the
stack to query these parameters. Notice lower layer drivers
can use the dcbnl_ops routines if additional handling is
needed. Perhaps in the firmware case for example
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Shmulik Ravid <shmulikr@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IEEE8021Qaz is the IEEE standard version of CEE. The
standard has had enough significant changes from the CEE
version that many of the CEE attributes have no meaning
in the new spec or do not easily map to IEEE standards.
Rather then attempt to create a complicated mapping
between CEE and IEEE standards this patch adds a nested
IEEE attribute to the list of DCB attributes. The policy
is,
[DCB_ATTR_IFNAME]
[DCB_ATTR_STATE]
...
[DCB_ATTR_IEEE]
[DCB_ATTR_IEEE_ETS]
[DCB_ATTR_IEEE_PFC]
[DCB_ATTR_IEEE_APP_TABLE]
[DCB_ATTR_IEEE_APP]
...
The following dcbnl_rtnl_ops routines were added to handle
the IEEE standard,
int (*ieee_getets) (struct net_device *, struct ieee_ets *);
int (*ieee_setets) (struct net_device *, struct ieee_ets *);
int (*ieee_getpfc) (struct net_device *, struct ieee_pfc *);
int (*ieee_setpfc) (struct net_device *, struct ieee_pfc *);
int (*ieee_getapp) (struct net_device *, struct dcb_app *);
int (*ieee_setapp) (struct net_device *, struct dcb_app *);
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is just a cleanup to make the static checkers happy. We don't need
to check "own" twice.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Ram Vepa <ram.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
ipv4: dont create routes on down devices
epic100: hamachi: yellowfin: Fix skb allocation size
sundance: Fix oopses with corrupted skb_shared_info
Revert "ipv4: Allow configuring subnets as local addresses"
USB: mcs7830: return negative if auto negotiate fails
irda: prevent integer underflow in IRLMP_ENUMDEVICES
tcp: fix listening_get_next()
atl1c: Do not use legacy PCI power management
mac80211: fix mesh forwarding
MAINTAINERS: email address change
net: Fix range checks in tcf_valid_offset().
net_sched: sch_sfq: fix allot handling
hostap: remove netif_stop_queue from init
mac80211/rt2x00: add ieee80211_tx_status_ni()
typhoon: memory corruption in typhoon_get_drvinfo()
net: Add USB PID for new MOSCHIP USB ethernet controller MCS7832 variant
net_sched: always clone skbs
ipv6: Fragment locally generated tunnel-mode IPSec6 packets as needed.
netlink: fix gcc -Wconversion compilation warning
asix: add USB ID for Logitec LAN-GTJ U2A
...
In ip_route_output_slow(), instead of allowing a route to be created on
a not UPed device, report -ENETUNREACH immediately.
# ip tunnel add mode ipip remote 10.16.0.164 local
10.16.0.72 dev eth0
# (Note : tunl1 is down)
# ping -I tunl1 10.1.2.3
PING 10.1.2.3 (10.1.2.3) from 192.168.18.5 tunl1: 56(84) bytes of data.
(nothing)
# ./a.out tunl1
# ip tunnel del tunl1
Message from syslogd@shelby at Dec 22 10:12:08 ...
kernel: unregister_netdevice: waiting for tunl1 to become free.
Usage count = 3
After patch:
# ping -I tunl1 10.1.2.3
connect: Network is unreachable
Reported-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joel Soete reported oopses during pppoe over sundance NIC, caused by
a bug in skb allocation and dma mapping code, where skb_reserve()
bytes weren't taken into account. As a followup to the patch:
"sundance: Fix oopses with corrupted skb_shared_info" very similar
code is fixed here for three other drivers.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Cc: Joel Soete <soete.joel@scarlet.be>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joel Soete reported oopses at the beginning of pppoe connections since
v2.6.35. After debugging the bug was found in sundance skb allocation
and dma mapping code, where skb_reserve() bytes aren't taken into
account. This is an old bug, only uncovered by some change in 2.6.35.
Initial debugging patch by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: Joel Soete <soete.joel@scarlet.be>
Tested-by: Joel Soete <soete.joel@scarlet.be>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change Details:
- Made IOC auto_recovery synchronized and not timer based.
- Only one PCI function will attempt to recover and reinitialize
the ASIC on a failure, that too after all the active PCI
functions acknowledge the IOC failure.
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change Details:
- Retrieve the VLAN configuration from the networking stack
and apply it to the base interface during ifconfig up
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change Details:
- Added a check in ioc firmware lock function to see if IOC is
in BFI_IOC_UNINIT state or not. If it is not in UNINIT state
and the last IOC boot was not done by OS driver, force IOC state
to BFI_IOC_UNINIT
- Unused macro and API cleanup
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change Details:
- Call netif_wake_queue() if we have freed up sufficient elements
at the end of completion processing
- Add netif_queue_stopped counter back to bnad_drv_stats {}
- Get netif_queue_stopped value from stack
- Remove BUG_ON() on value returned by pci_unmap_addr()
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change Details:
- Enable reception of pure priority tagged packets by default by
turning on VLAN Id = 0
- Clear the promiscuous mode, all multicast mode flags when
bna_rxf_uninit is called
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change Details:
- Removed semaphore register dump from ethtool
- Moved netif_carrier_off() call to before calling bna_init()
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change Details:
- Fixed port enable/disable sync through a change in LL port state
machine
- Change txq->priority masking to 0x7 (3 bits) from 0x3 (2 bits)
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change Details:
- Check HW ready condition before accessing h/w register in data-path
- Postpone clean-up of data buffers to the data-path restart path and
wait in the cleanup routines for in-flight DMA to complete
- Separate out Tx completion processing from Rx poll routine
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The X540 introduces a new Virtual Function device ID so that the X540
VF device can be distinguished from the 82599 VF device. The X540 VF
device will have additional capability over the 82599 VF device so it
is necessary to be able to discern the difference.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for the anti-spoofing feature in the HW. Packets from
VF devices with spoofed MAC addresses or VLAN tags will be blocked
and a counter incremented. During the watchdog timer the spoofed
packet dropped counter is read and if it is non-zero then a warning
message is displayed on the host VMM's console.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add X540 specific feature support to X540
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Print warnings to the system log when the VF attempts to override
MAC/VLAN settings that were configured by the VMM Host administrator
using the ip link set commands.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support to igbvf for the new i350 virtual function device.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change forces the link down when a mailbox timeout has occurred.
Previously it was possible for a mailbox timeout to occur but for the
interface to stay up. The problem with this was that it became possible
for an interface to stay up and miss multiple requests resulting in a
possible issue since the interface will be running in an unknown state.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for the anti-spoofing feature in the HW. Packets from
VF devices with spoofed MAC addresses or VLAN tags will be blocked
and an event generated. When the watchdog task runs it will call a
function to check if any spoof events occurred. If an event was
detected then a warning message is dumped to the system log.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch does the following:
1. Changes the existing supported device id's so now DH89xxCC is not supported when EEPROM is not read.
2. Adds two more device ids for DH89xxCC in backplane mode and SFP.
3. Driver now initializes previously possibly uninitialized value in igb_reset_mdicnfg_82580().
Signed-off-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Print a warning message to the system log when the VF attempts to
override administratively set MAC/VLAN configuration.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The vf flags were being overwritten causing the flag that indicates
that the PF has set the VF MAC address to get cleared. This would
allow the VF to override the MAC address assigned by the Host VMM
using the ip link set command.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
WARNING: braces {} are not necessary for any arm of this statement
WARNING: braces {} are not necessary for single statement blocks
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ERROR: that open brace { should be on the previous line
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ERROR: trailing statements should be on next line
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ERROR: Macros with complex values should be enclosed in parenthesis
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
- Update the Intel Wired LAN documentation with the latest
URL for ethtool.
- replace "Ethtool" with "ethtool"
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
* 'merge' of git://git.secretlab.ca/git/linux-2.6:
spi/mpc52xx-spi: fix annotation for remove()-pointer
spi/fsl_espi: fix wrong setting of the address in the command buffer
spi/fsl_espi: change the read behaviour of the SPIRF
of/i2c: Fix request module by alias
powerpc/mpc5200: include fs.h in mpc52xx_gpt.c
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: issue DIPM enable commands with LPM state updated
libata: no special completion processing for EH commands
pata_mpc52xx: driver needs BMDMA
pata_cs5536: Add support for non-X86_32 platforms
libata-sff: fix HSM_ST_ERR handling in __ata_sff_port_intr()
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: print out alloc information with KERN_DEBUG instead of KERN_INFO
kthread_work: make lockdep happy
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] fix up documentation for change in ->queuecommand to lockless calling
[SCSI] bfa: rename log_level to bfa_log_level
Low level drivers may behave differently depending on the current
link->lpm_policy. During ata_eh_set_lpm(), DIPM enable commands are
issued after the successful completion of ap->ops->set_lpm(), which
means that the controller is already in the target state. This causes
DIPM enable commands to be processed with mismatching controller power
state and link->lpm_policy value.
In ahci, link->lpm_policy is used to ignore certain PHY events if LPM
is enabled; however, as DIPM commands are issued with stale
link->lpm_policy, they sometimes end up triggering these conditions
and get aborted leading to LPM configuration failure.
Fix it by updating link->lpm_policy before issuing DIPM enable
commands.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Kyle McMartin <kyle@mcmartin.ca>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata_qc_complete() contains special handling for certain commands. For
example, it schedules EH for device revalidation after certain
configurations are changed. These shouldn't be applied to EH
commands but they were.
In most cases, it doesn't cause an actual problem because EH doesn't
issue any command which would trigger special handling; however, ACPI
can issue such commands via _GTF which can cause weird interactions.
Restructure ata_qc_complete() such that EH commands are always passed
on to __ata_qc_complete().
stable: Please apply to -stable only after 2.6.38 is released.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Kyle McMartin <kyle@mcmartin.ca>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Found by this build-error if BMDMA is disabled:
drivers/ata/pata_mpc52xx.c: In function 'mpc52xx_ata_init_one':
drivers/ata/pata_mpc52xx.c:662: error: 'ata_bmdma_interrupt' undeclared (first use in this function)
...
Move the Kconfig entry to the proper location as needed since
9a7780c9ac (libata-sff: make BMDMA optional)
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
pata_cs5536 does work on the other platforms(e.g. Loongson, a MIPS
variant), so, remove the dependency of X86_32 and fix the building
errors under the other platforms via only reserving the X86_32 specific
parts for X86_32.
pata_amd also supports cs5536 IDE controller, but this one saves about
33k for the compressed kernel image(vmlinuz for MIPS).
Signed-off-by: Zhang Le <r0bertz@gentoo.org>
Signed-off-by: Chen Jie <chenj@lemote.com>
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
While separating out BMDMA irq handler from SFF, commit c3b28894
(libata-sff: separate out BMDMA irq handler) incorrectly made
__ata_sff_port_intr() consider an IRQ to be an idle one if the host
state was transitioned to HSM_ST_ERR by ata_bmdma_port_intr().
This makes BMDMA drivers ignore IRQs reporting host bus error which
leads to timeouts instead of triggering EH immediately. Fix it by
making __ata_sff_port_intr() consider the IRQ to be an idle one iff
the state is HSM_ST_IDLE. This is equivalent to adding HSM_ST_ERR to
the "break"ing case but less error-prone.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Antonio Toma <antonio.toma@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Or else we can't operate on the right address when the trans length
is greater than 65535.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The user must read N bytes of SPIRF (1 <= N <= 4) that do not exceed the
amount of data in the receive FIFO, so read the SPIRF byte by byte when
the data in receive FIFO is less than 4 bytes.
On Simics, when read N bytes that exceed the amount of data in receive
FIFO, we can't read the data out, that is we can't clear the rx FIFO,
then the CPU will loop on the espi rx interrupt.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
If we are registering an i2c device that has a device tree node like
this real-world example:
rtc@68 {
compatible = "dallas,ds1337";
reg = <0x68>;
};
of_i2c_register_devices() will try to load a module called ds1337.ko.
There is no such module, so it will fail. If we look in modules.alias
we will find entries like these:
.
.
.
alias i2c:ds1339 rtc_ds1307
alias i2c:ds1338 rtc_ds1307
alias i2c:ds1337 rtc_ds1307
alias i2c:ds1307 rtc_ds1307
alias i2c:ds1374 rtc_ds1374
.
.
.
The module we want is really called rtc_ds1307.ko. If we request a
module called "i2c:ds1337", the userspace module loader will do the
right thing (unless it is busybox) and load rtc_ds1307.ko. So we add
the I2C_MODULE_PREFIX to the request_module() string.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Shmulik Ravid