Add helpers to synchronously write registers of the wiimote. This is heavily
used by initialization functions for wiimote peripherals.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
To initialize wiimote peripherals, the stream to the wiimote must be held
exclusively by the initializer, otherwise the initialization will fail. Many
initializations require multiple memory requests to be sent synchronously so we
need a way to lock the stream and release it when we are done.
This adds several helper functions which allow to lock the stream, then send
requests, wait for the answers and release the stream again.
When holding the lock, the function may sleep and interrupted by signals.
Also it returns after a short timeout so userspace shouldn't notice long
delays.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The wiimote allows direct access to its memory mapped registers and
internal eeprom. This adds support to access this memory and handle
memory events.
There are two macros which wrap up the memory access functions to avoid
accidentally overwriting sensitive eeprom data because a boolean value
was wrongly set.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If an extension is connected the wiimote may report data though DRMs that
contain extension data. This adds handlers for these DRMs but discards extension
data since we do not support it, yet.
It prints a warning to kernel log if an unhandled report is catched. Since we
handle all requests now, this should never happen, though.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Parse IR data and report it to IR input-device. IR data is sent in 3 different
formats, but we only support the basic format as there is no way to send the
additional information to userspace.
All three formats are compatible with the basic IR data format so we need only
one parser.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The IR cam of the wiimote reports 4 trackable lights as absolute values. Since
we can turn the IR cam on and off, we register a separate input device so we can
react on open/close callbacks to save wiimote battery power when IR cam is not
needed.
The cam can be in four states: off, basic, extended and full
The DRM chooser automatically selects a proper DRM that includes all required IR
data so no information is lost.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add parser functions for accelerometer data reported by the wiimote. The data is
almost always reported in the same format, so we can use a single handler.
However, an own handler function is created for each DRM-mode because when IR
and extension support is added, each of them is parsed differently.
Also set the appropriate DRM including accelerometer data on DRM requests to
actually retrieve the accelerometer data.
Data is reported to userspace as ABS_RX/Y/Z values. The values are between -500
and 500 and 0 means no acceleration. See also userspace xwiimote library for
data parsing.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add new input device for every wiimote which is used to report accelerometer
data to userspace. Only if the input device is currently open, we make the
wiimote send accelerometer data. This saves a whole lot of energy on the wiimote
if an application is only interested in button input reports.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The wiimote has a single rumble motor. This adds force feedback support for
wiimote devices with FF_RUMBLE. The rumble motor is very simple and only
supports an on/off switch so no complex ff-effects are supported.
This also removes the event callback that was registered before but unused. The
ff-device overwrites this callback, anyway.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This adds support for the wiimote's rumble device. Every output report can
enable and disable the rumble motor. Hence, every output report must look up our
new RUMBLE flag and make sure that it does not unintentionally toggle the
rumble motor.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This is basically a more generic respin of 23746a6 ("HID: magicmouse: ignore
'ivalid report id' while switching modes") which got reverted later by
c3a492.
It turns out that on some configurations, this is actually still the case
and we are not able to detect in runtime.
The device reponds with 'invalid report id' when feature report switching it
into multitouch mode is sent to it.
This has been silently ignored before 0825411ade ("HID: bt: Wait for ACK
on Sent Reports"), but since this commit, it propagates -EIO from the _raw
callback .
So let the driver ignore -EIO as response to 0xd7,0x01 report, as that's
how the device reacts in normal mode.
Sad, but following reality.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=35022
Reported-by: Chase Douglas <chase.douglas@canonical.com>
Reported-by: Jaikumar Ganesh <jaikumarg@android.com>
Tested-by: Chase Douglas <chase.douglas@canonical.com>
Tested-by: Jaikumar Ganesh <jaikumarg@android.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We recently introduced locking into this function, but we missed an
error path which needs an unlock.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The wiimote resets the current drm when an extension is plugged in.
Fortunately, it also sends a status report in this situation so we just
reset the drm on every status report to keep the drm consistent.
Also handle return reports from the wiimote which indicate success and
failure of requests that we've sent.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The wiimote reports data in several data reporting modes (DRM). The DRM
request makes the wiimote send data in the requested drm.
The DRM mode can be set explicitely or can be chosen by the driver. To let
the driver choose the DRM mode, pass WIIPROTO_REQ_NULL placeholder to it. This
is no valid request and is replaced with an appropriate DRM.
Currently, the driver always sets the basic DRM_K mode, but this will be
extended when further peripherals like accelerometer and IR are supported.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This registers 4 led devices to allow controlling the wiimote leds via standard
LED sysfs API. It removes the four sysfs attributes so we don't have two APIs
for one device.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Even though the bluetooth hid backend does not react on open/close callbacks, we
should call them to be consistent with other hid drivers.
Also the new input open/close handlers will be used in future to prepare the
wiimote device for IR/extension input.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The new locking scheme in HID core allows us to remove a bit of synchronization.
Since the HID layer acts synchronously we simply register input core last and
there are no synchonization issues anymore.
Also register sysfs files after that to simplify the code.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is a small rare potential memory leak here. Also Walter Harms
points out that we can do a small cleanup as well by using kstrdup().
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Patch to add SiGma Micro-based keyboards (1c4f:0002) to hid-quirks.
These keyboards dont seem to allow the records to be initialized, and hence a
timeout occurs when the usbhid driver attempts to initialize them. The patch
just adds the signature for these keyboards to the hid-quirks list with the
setting HID_QUIRK_NO_INIT_REPORTS. This removes the 5-10 second wait for the
timeout to occur.
Signed-off-by: Jeremiah Matthey <sprg86@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch (as1482) adds a macro for testing whether or not a
pm_message value represents an autosuspend or autoresume (i.e., a
runtime PM) event. Encapsulating this notion seems preferable to
open-coding the test all over the place.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This panel is also known as the Dell ST2220Tc.
Signed-off-by: jeffbrown@android.com
Reviewed-By: Benjamin Tissoires <Benjamin_Tissoires@logitech.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This change fixes two problems.
First, it ensures that the hid-multitouch driver does not incorrectly
map GenericDesktop usages that are intended for other applications,
such as a Mouse.
Second, it sets the appropriate input properties so that user-space
can distinguish TouchScreen devices (INPUT_PROP_DIRECT) from
TouchPad devices (INPUT_PROP_POINTER) and configure them accordingly.
Signed-off-by: jeffbrown@android.com
Acked-By: Benjamin Tissoires <Benjamin_Tissoires@logitech.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Support force feedback on the Dual USB Force Feedback Joypad (MP-8866).
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Do this for backwards compatibility reasons (LOGIWHEELS_FF has
been split-off from LOGITECH_FF), so that users don't have
regressions with 'default' kernel configs.
Reported-and-tested-by: simon@mungewell.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Otherwise the generic driver wouldn't unbind from it and wouldn't
let hid-apple to automatically take over.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Added USB device IDs for MacBookAir4,2 keyboard. Device constants were
copied from the MacBookAir3,2 constants. The 4,2 device specification is
reportedly unchanged from the 3,2 predecessor and seems to work well.
Signed-off-by: Joshua V Dillon <jvdillon@gmail.com>
Signed-off-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add touch surface resolution information. The size of the touch surfaces
has been determined to the hundredth of a mm.
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Michael Poole <mdpoole@troilus.org>
Cc: linux-input@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Chase Douglas <chase.douglas@canonical.com>
[jkosina@suse.cz: update comments and commit message]
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix a return value propagation that was omitted in David Herrmann's
locking fix around hid_input_report().
Reported-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
HID low level drivers register new devices with the HID core which then
adds the devices to the HID bus. The HID bus normally immediately probes
an appropriate driver which then handles HID input for this device.
The ll driver now uses the hid_input_report() function to report input
events for a specific device. However, if the HID bus unloads the driver
at the same time (for instance via a call to
/sys/bus/hid/devices/<dev>/unbind) then the hdev->driver pointer may be
used by hid_input_report() and hid_device_remove() at the same time
which may cause hdev->driver to point to invalid memory.
This fix adds a semaphore to every hid device which protects
hdev->driver from asynchronous access. This semaphore is locked during
driver *_probe and *_remove and also inside hid_input_report(). The
*_probe and *_remove functions may sleep so the semaphore is good here,
however, hid_input_report() is in atomic context and hence only uses
down_trylock(). If it cannot acquire the lock it simply drops the input
package.
The low-level drivers report input events synchronously so
hid_input_report() should never be entered twice at the same time on the
same device. Hence, the lock should always be available. But if the
driver is currently probed/removed then the lock is not available and
dropping the package should be safe because this is what would have
happened if the package arrived some milliseconds earlier/later.
This also fixes another race condition while probing drivers:
First the *_probe function of the driver is called and only if that
succeeds, the related input device of hidinput is registered. If the low
level driver reports input events after the *_probe function returned
but before the input device is registered, then a NULL pointer
dereference will occur. (Equivalently on driver remove function).
This is not possible anymore, since the semaphore lock drops all
incoming packages until the driver/device is fully initialized.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
No need for freeing pm in case when it's not allocated.
Reported-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Bojan Prtvar <prtvar.b@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The description of lg4ff driver has to be changed to reflect the fact that the
driver now handles a lot more Logitech wh the Wii. Entry in Kconfig has been
renamed to LOGIWHEELS_FF
Signed-off-by: Michal Malý <madcatxster@gmail.com>
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Logitech driver sends Formula Force EX wheel a different command to
autocenering force. FFEX will accept the standard command used by the rest of
the wheels, but it won't set the centering properly.
Signed-off-by: Michal Malý <madcatxster@gmail.com>
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Wheel range of certain Logitech wheels - namely Driving Force GT, Driving Force
Pro, G25 and G27 can be adjusted. Minimu is 40 degrees, maximum 900. DFGT, G25
and G27 all use a common command, DFP uses another one. Range can be set from
userspace by writing to
"/sys/module/hid_logitech/drivers/hid:logitech/<dev>range". The driver use list
to store range of each connected wheel; it's not possible to use driver_data in
hid_device struct as it's already b hig-lg driver.
Signed-off-by: Michal Malý <madcatxster@gmail.com>
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch allows the lg4ff driver to switch wheels to the native mode. Since
this is specific to Logitech wheels only, it's handled in hid-lg4ff rather than
hid-lg.
Signed-off-by: Michal Malý <madcatxster@gmail.com>
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This is the first out of five patches me and Simon Wood (CC'd) have been
working on. It separates the handling of Logite from the generic lgff driver
and adds additional features specific for the Logitech wheels, namely
- Native mode support for Driving Force GT, Driving Force Pro, G25 and G27
wheels Every Logitech wheel reports itself as generic Logitech Driving Force
wheel (VID 046d, PID c294). This is done to ensu wheel will work on every USB
HID-aware system even when no Logitech driver is available. It however limits
the capabilit wheel - range is limited to 200 degrees, G25/G27 don't report the
clutch pedal and there is only one combined axis for t brake. The switch to
native mode is done via hardware-specific command which is different for each
wheel. When the wheel receives such command, it simulates reconnect and reports
to the OS with its actual PID.
- Adjustable wheel range DFGT, DFP, G25 and G27 have variable range of the
steering wheel. The range is limited by applying a maximum constant when the
wheel is turned beyond the allowed range. The limit as also set by a
hardware-specific command. There is a comm command for DFGT, G25 and G27 and
another one for DFP. It is probably possible to use the DFP command to limit
the range other Logitech wheels too, but this is not supported by the official
Logitech driver for Windows. The patch adds a sysfs interface which allows for
the range to be set from userspace.
- Fixed autocentering command All Logitech wheels support FF_AUTOCENTER effect.
The original implementation in the lgff driver didn't work well with patch
fixes it. According to USB communication sniffs the Formula Force EX (pretty
much rebranded original Driving Force accept the generic autocentering command,
this issue is also addressed by the patch
There are still some features this patch doesn't cover, but since some of them
will most likely require modifications of memless driver we have decided not to
include them yet.
As first we decided to move the handling of Logitech wheels from hid-lgff
driver to hid-lg4ff driver (originally used fo At also adds PID of Logitech
Driving Force GT.
Signed-off-by: Michal Malý <madcatxster@gmail.com>
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There are gamepads that share the same VID and PID but have different
report structure - instead of having 4 fields with one value they have
one field that can hold all 4 values. Make the driver cope with devices
using both styles.
Signed-off-by: Sergei Kolzun <x0r@dv-life.ru>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The config option needs to be a 'bool' and not a tristate, otheriwse
force feedback support never makes it into the module.
Signed-off-by: Sergei Kolzun <x0r@dv-life.ru>
Cc: stable@kernel.org
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add USB device ids for the new revision (MB110LL/B) of Apple's wired aluminum
keyboard. I have only confirmed that the ANSI version is correct - it is
assumed that the ISO and JIS versions follow the standard numbering convention.
Signed-off-by: Dan Bastone <dan@pwienterprises.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds support for the CSR panel built by XAT.
Signed-off-by: Ice Chien <ice.chien@accupoint.com.tw>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The following symbols are not referenced outside this file so
there's no need for it to be in the global name space.
pcmidi_sustained_note_release
init_sustain_timers
stop_sustain_timers
pcmidi_handle_report
pcmidi_setup_extra_keys
pcmidi_snd_initialise
pcmidi_snd_terminate
Make them static.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hid_hw_stop() must be called in ax_probe() error path if hid_hw_start()
was successful.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Microsoft comfort mouse 4500 report descriptor contains duplicate
usages for horizontal wheel. This patch fixes the wrong mapping
caused by that.
Signed-off-by: Ari Savolainen <ari.m.savolainen@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for UC-Logic Tablet WP1062 by fixing its report descriptor.
This tablet is sold as Monoprice 10X6.25 Inches Graphic Drawing Tablet.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add sysfs files for each led of the wiimote. Writing 1 to the file
enables the led and 0 disables the led.
We do not need memory barriers when checking wdata->ready since we use
a spinlock directly after it.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Save the current state of the leds in the wiimote data structure. This
allows us to discard new led requests that wouldn't change anything.
Protect the whole state structure by a spinlock. Every wiiproto_*
function expects this spinlock to be held when called.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add new request that sets the leds on the target device. Also, per
default, set led1 after initializing a device.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Parse input report 0x30 from the wiimote as button input. We need to
send events for all buttons on every input report because the wiimote
does not send events for single buttons but always for all buttons
to us. The input layer, however, filters redundant events.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Create array of all event handlers and call each handler when we
receive the related event.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The raw hid output function that is supported by bluetooth low-level
hid driver does not provide an output queue and also may sleep. The
wiimote driver, though, may need to send data in atomic context so
this patch adds a buffered output queue for the wiimote driver.
We use the shared workqueue to send our buffer to the hid device.
There is always only one active worker which flushes the whole output
queue to the device. If our queue is full, every further
output is discarded.
Special care is needed in the deinitialization routine. When
wiimote_hid_remove is called, HID input is already disabled, but HID
output may still be used from our worker and is then discarded by the
lower HID layers. Therefore, we can safely disable the input layer since it
is the only layer that still sends input events.
Future sysfs attributes must be freed before unregistering input to
avoid the sysfs handlers to send input events to a non-existing input
layer.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The wiimote driver needs to send raw output reports to the wiimote
device. Otherwise we could not manage the peripherals of the wiimote
or perform memory operations on the wiimote.
We cannot use hidinput_input_event of the lowlevel hid driver, since
this does not accept raw input. Therefore, we need to use the same
function that hidraw uses to send output. Side effect is, the raw
output function is not buffered and can sleep.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The wiimote first starts HID hardware and then registers the input
device. We need to synchronize the startup so no event handler will
start parsing events when the wiimote device is not ready, yet.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Register input device so the wiimote can report input events on
it. We do not use HIDINPUT because the wiimote does not provide any
descriptor table which might be used by HIDINPUT. So we avoid
having HIDINPUT parse the wiimote descriptor and create unrelated
or unknown event flags. Instead we register our own input device
that we have full control of.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Allocate wiimote device structure with all wiimote related data
when registering new wiimote devices.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The wiimote uses a fake HID protocol. Hence, we need to prevent
HIDINPUT and HIDDEV from parsing wiimote data and instead parse
raw hid events.
Add VID/PID to hid-core so the special driver is loaded on new
wiimotes.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add stub driver for the Nintendo Wii Remote. The wii remote uses
the HID protocol to communicate with the host over bluetooth. Hence,
add dependency for HIDP and place driver in hid subsystem.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add force feedback support for Holtek On Line Grip based HID devices.
The protocol is more complex than that of most other rumblepads, but the
device still needs to be handled as a memoryless one.
Tested by Cleber de Mattos Casali with a 1241:5015 "Clone Joypad Super
Power Fire" gamepad, with help from Hendrik Iben <hendrik_iben@web.de>.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Tested-by: Cleber de Mattos Casali <clebercasali@yahoo.com.br>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
while merging hid-stantum into hid-multitouch, I did not correctly copy/paste
the VIDs for those devices. This patch fixes it.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In case a device does not provide the feature "Maximum Contact Count",
or set it at 0, the maxcontacts field may be at 0 while calling
input_mt_init_slots.
This patch ensures that hid-multitouch will allways report
ABS_MT_SLOT and ABS_MT_TRACKING_ID to the user space.
This corrects a bug found with some Ilitek devices that has been
integrated in 3.0-rc0.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 23746a66d7.
It turned out that the actual reason for failure is not the device
firmware, but bug in Bluetooth stack, which will be fixed by
patch by Ville Tervo which corrects the mask handling for CSR 1.1
Dongles.
Reported-and-tested-by: Ed Tomlinson <edt@aei.ca>
Reported-and-tested-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Digital Media 3000 keyboard (USB id: 0x0730) features the same 1-5
Application Launch keys that the Natural Ergonomic 4000 has. Add its
usb id to the list of quirks.
Reported-by: Khelben Blackstaff <eye.of.the.8eholder@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The accelerometers/gyro on the Sixaxis are reported in the wrong
endianness (ie. not compatible with HID), so this patch intercepts
the report and swaps the appropriate bytes over.
Accelerometers are scaled with a nominal value of +/-4000 = 1G,
maximum value would be around +/-32768 = 8G.
Gyro on my device always reports -32768, might need some calibration
set within the controller.
Fix extracted from previous patch submission:
https://patchwork.kernel.org/patch/95212/
Signed-off-by: Marcin Tolysz <tolysz@gmail.com>
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
On rare occassions raw events can be triggered before drvdata gets set up
which leads to NULL pointer dereferences. This was only observed with pyra on
2.6.39, but is fixed for all devices now to play it save.
kovaplus returned wrong actual values when profile change was initiated from host.
Added range checks for setting actual profile on all devices.
Signed-off-by: Stefan Achatz <erazor_de@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Removed analog feature report enums and modified code in roccat_common
to reflect this. Non standard conform Kone got its own copy of the old
code. That helps extracting more generalizations for newer devices.
Signed-off-by: Stefan Achatz <erazor_de@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
As module roccat is needed by all devices, it's the toplevel
menu entry with all devices dependent.
Signed-off-by: Stefan Achatz <erazor_de@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Added binary sysfs attribute to support new functionality the manufacturer
added to koneplus.
Signed-off-by: Stefan Achatz <erazor_de@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Since the inclusion of eGalax devices in 2.6.39, I've got some
bug reports for 480d and other devices.
The problem lies in the reports descriptors: eGalax supports both
pen and fingers, and so the reports descriptors contained both.
But hid-multitouch relies on them to detect the last item in each
field to send the multitouch events. In 480d, the last item is not
Y as it should but Pressure. That means that the fields are not
aligned and X,Y are at 0,0 (the other touch coordinates of the report).
With this patch, the detection is made only when the field ContactID
has been detected inside the collection.
There is still a problem with the detections of the range as stylus
and fingers may not have the same min/max, but it's a start.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Speedlink VAD Cezanne have a hardware bug that makes the cursor "jump" from one
place to another every now and then. The issue are relative motion events
erroneously reported by the device, each having a distance value of +256. This
256 can in fact never occur due to real motion, therefore those events can
safely be ignored. The driver also drops useless EV_REL events with a value of
0, that the device sends every time it sends an "real" EV_REL or EV_KEY event.
Signed-off-by: Stefan Kriwanek <mail@stefankriwanek.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
- Add the quirk "NOGET" to make the wheel work at all in native mode.
- Replace the somehow broken report descriptor with a custom one to have
separate throttle and brake axes.
As there are significant differences in the descriptor (original descriptor
"hides" the separate axes in a 24 bit FF00 usagepage, new descripter replaces
that with two individual 8 bit desktop.y and desktop.rz usages) I provided a
complete replacement descriptor instead trying to patch the original one.
Patching the descriptor seems not feasible as the new one is much larger.
Note: To actually test this you have to use the tool "ltwheelconf" to put the
DFP into it's native mode - See below for more info.
Background:
Most Logitech wheels are initially reporting themselves with a "fallback"
deviceID (USB_DEVICE_ID_LOGITECH_WHEEL - 0xc294), in order to make sure they
are working even without having the proper driver installed.
If the Logitech driver is installed it sends a special command to the wheel
which sets the wheel to "native mode", enabling enhance features like:
- Clutch pedal
- extended wheel rotation range (up to 900 degrees)
- H-gate shifter
- separate axis for throttle / brake
- all buttons
When the wheel is set to native mode it basically disconnects and reconnects
with a different deviceID (USB_DEVICE_ID_LOGITECH_DFP_WHEEL - 0xc298 in this
case).
I am working on a userspace tool [1] which does the switching from fallback to
native mode. During development I found out that the Driving Force Pro wheel
is not supported in native mode - quierk NOGET is missing and the throttle and
brake axes are reported in a combined way only.
Signed-off-by: Michael Bauer <michael@m-bauer.org>
Signed-off-by: Simon Wood <simon@mungewell.org>
[1] https://github.com/TripleSpeeder/LTWheelConf
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There are a couple use after free bugs here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
[jkosina@suse.cz: removed already fixed hunk]
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add 5543:0064 UC-Logic Technology Corp. Aiptek HyperPen 10000U to quirks with
HID_QUIRK_MULTI_INPUT.
Originally the device is reporting the x,y coordinates on Z and RX. By adding
this quirk, there will be two kernel devices. The first one is muted and the
second device will report coordinates on X and Y.
Signed-off-by: Jimmy Hon <honyuenkwun@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 6cb4b04079 ("HID: hiddev: fix race between hiddev_disconnect
and hiddev_release") made it possible to access hiddev (for unlocking
the existance mutex) once hiddev has been kfreed.
Change the order so that this can not happen (always unlock the mutex first,
it is needed only to protect access to ->exist and ->open).
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (205 commits)
USB: EHCI: Remove SPARC_LEON {read,write}_be definitions from ehci.h
USB: UHCI: Support big endian GRUSBHC HC
sparc: add {read,write}*_be routines
USB: UHCI: Add support for big endian descriptors
USB: UHCI: Use ACCESS_ONCE rather than using a full compiler barrier
USB: UHCI: Add support for big endian mmio
usb-storage: Correct adjust_quirks to include latest flags
usb/isp1760: Fix possible unlink problems
usb/isp1760: Move function isp1760_endpoint_disable() within file.
USB: remove remaining usages of hcd->state from usbcore and fix regression
usb: musb: ux500: add configuration and build options for ux500 dma
usb: musb: ux500: add dma glue layer for ux500
usb: musb: ux500: add dma name for ux500
usb: musb: ux500: add ux500 specific code for gadget side
usb: musb: fix compile error
usb-storage: fix up the unusual_realtek device list
USB: gadget: f_audio: Fix invalid dereference of initdata
EHCI: don't rescan interrupt QHs needlessly
OHCI: fix regression caused by nVidia shutdown workaround
USB: OTG: msm: Free VCCCX regulator even if we can't set the voltage
...
This patch sorts the defs for the MT_CLS. I choose to split
generic classes and device specific ones to be able to add
more generic classes in the future.
It also put eGalax devices at their right place (alphabetically)
in mt_devices.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Stantum devices used to work with MT_CLS_STANTUM but MT_CLS_CONFIDENCE
is exactly the same. This patch switches them to this generic class,
and remove the unused MT_CLS_STANTUM.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch introduce support for Unitec panels.
This device has not been optimized in term of kernel processing
operations (default class), but it will work.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch introduce support for Touch International panels.
This device has not been optimized in term of kernel processing
operations (default class), but it will work.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch introduce support for GoodTouch panels.
This device has not been optimized in term of kernel processing
operations (default class), but it will work.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch introduce support for CVTouch panels.
This device has not been optimized in term of kernel processing
operations (default class), but it will work.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch introduce support for ActionStar panels.
This device has not been optimized in term of kernel processing
operations (default class), but it will work.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When hiddev_disconnect() runs with chardev open, it will proceed with
usbhid_close(). When userspace in parallel runs the hiddev_release(),
it sees !hiddev->exists (as it has been already set so by
hiddev_disconnect()) and kfrees hiddev while hiddev_disconnect() hasn't
finished yet.
Serialize the access to hiddev->exists and hiddev->open by existancelock.
Reported-by: mike-@cinci.rr.com
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The device reponds with 'invalid report id' when feature report switching it
into multitouch mode is sent to it.
This has been silently ignored before 0825411ade ("HID: bt: Wait for ACK
on Sent Reports"), but since this commit, it propagates -EIO from the _raw
callback .
So let the driver ignore -EIO as response to 0xd7,0x01 report, as that's
how the device reacts in normal mode.
Sad, but following reality.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=35022
Tested-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
I'm using a Data Modul EasyTouch USB multitouch controller,
which is issuing a hid report with a size equals to 0. The rsize
value gets set to 536870912 and Linux is crashing in the memset
because the value is too big.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds support for Elo TouchSystems 2515 IntelliTouch Plus
that can be found in Lenovo A700 all-in-one.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
I've got a Tivo Slide bluetooth remote/dongle, which uses a fair number
of hid usages that aren't currently mapped in hid-input.c. I'd initially
written additions to hid-input.c with just this device in mind,
including some bits that were specific to the device. This go around,
I'm looking at adding/correcting as many generic HID usages from the HID
Usage Tables, version 1.12, as I can -- which also serves to enable all
but four of the buttons on the Tivo Slide remote[*].
Outside of fixing the obviously incorrect mapping of 0xc 0x45 from
KEY_RADIO to KEY_RIGHT, and making use of the new KEY_IMAGES (just added
in 2.6.39-rc4) for AL Image Browser instead of KEY_MEDIA, these are
purely additions, and thus should have no negative impact on any already
functional HID devices. Most of the added mappings seemed to be
perfectly logical to me, but there were a few that were mapped on more
of an "I think this makes the most sense" basis.
[*] I'll handle the last four tivo buttons via an hid-tivo.c follow-up.
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CC: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
startup_profile and actual_profile didn't work as expected. Also
as the actual profile is persistent, the distinction between the
two was ambiguous, so both use the same code now and startup_profile
has been deprecated. Also the event is now propagated through
chardev. The userland tool has been updated to support this change.
Signed-off-by: Stefan Achatz <erazor_de@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
David Herrmann