Adding dcbnl implementation to bnx2x allowing users to manage the
embedded DCBX engine.
This patch is dependent on the following patches:
[net-next-2.6 PATCH 1/3] dcbnl: add support for ieee8021Qaz attributes
[net-next-2.6 PATCH 2/3] dcbnl: add appliction tlv handlers
[net-next-2.6 PATCH 3/3] net_dcb: add application notifiers
Signed-off-by: Shmulik Ravid <shmulikr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is just a cleanup to make the static checkers happy. We don't need
to check "own" twice.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Ram Vepa <ram.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The intent here was to test if the allocation failed but we tested
"SharedMemSize" instead of "SharedMemAddr" by mistake.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linux would not connect to other router running old version Cisco IOS (12.0).
This is most likely a bug in that version of IOS, since it is fixed
in later versions. As a workaround this patch allows a module parameter
to be set to disable compressing the protocol ID.
See: https://bugzilla.vyatta.com/show_bug.cgi?id=3979
RFC 1990 allows an implementation to formulate MP fragments as if protocol
compression had been negotiated. This allows us to always send compressed
protocol IDs. But some implementations don't accept MP fragments with
compressed protocol IDs. This parameter allows us to interoperate with
them. The default value of the configurable parameter is the same as the
current behavior: protocol compression is enabled. If protocol compression
is disabled we will not send compressed protocol IDs.
This is based on an earlier patch by Bob Gilligan (using a sysctl).
Module parameter is writable to allow for enabling even if ppp
is already loaded for other uses.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch avoids disabling the vlan flags using ethtool.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
ipv4: dont create routes on down devices
epic100: hamachi: yellowfin: Fix skb allocation size
sundance: Fix oopses with corrupted skb_shared_info
Revert "ipv4: Allow configuring subnets as local addresses"
USB: mcs7830: return negative if auto negotiate fails
irda: prevent integer underflow in IRLMP_ENUMDEVICES
tcp: fix listening_get_next()
atl1c: Do not use legacy PCI power management
mac80211: fix mesh forwarding
MAINTAINERS: email address change
net: Fix range checks in tcf_valid_offset().
net_sched: sch_sfq: fix allot handling
hostap: remove netif_stop_queue from init
mac80211/rt2x00: add ieee80211_tx_status_ni()
typhoon: memory corruption in typhoon_get_drvinfo()
net: Add USB PID for new MOSCHIP USB ethernet controller MCS7832 variant
net_sched: always clone skbs
ipv6: Fragment locally generated tunnel-mode IPSec6 packets as needed.
netlink: fix gcc -Wconversion compilation warning
asix: add USB ID for Logitec LAN-GTJ U2A
...
# iw wlan0 interface add moni0 type monitor flags control
# ip link set moni0 up
causes a continuous spew of FH_ERROR from the
device. Fix this by not setting the CTL2HOST
filter by itself -- CTL + promisc works fine.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Joel Soete reported oopses during pppoe over sundance NIC, caused by
a bug in skb allocation and dma mapping code, where skb_reserve()
bytes weren't taken into account. As a followup to the patch:
"sundance: Fix oopses with corrupted skb_shared_info" very similar
code is fixed here for three other drivers.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Cc: Joel Soete <soete.joel@scarlet.be>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joel Soete reported oopses at the beginning of pppoe connections since
v2.6.35. After debugging the bug was found in sundance skb allocation
and dma mapping code, where skb_reserve() bytes aren't taken into
account. This is an old bug, only uncovered by some change in 2.6.35.
Initial debugging patch by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: Joel Soete <soete.joel@scarlet.be>
Tested-by: Joel Soete <soete.joel@scarlet.be>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change Details:
- Made IOC auto_recovery synchronized and not timer based.
- Only one PCI function will attempt to recover and reinitialize
the ASIC on a failure, that too after all the active PCI
functions acknowledge the IOC failure.
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change Details:
- Retrieve the VLAN configuration from the networking stack
and apply it to the base interface during ifconfig up
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change Details:
- Added a check in ioc firmware lock function to see if IOC is
in BFI_IOC_UNINIT state or not. If it is not in UNINIT state
and the last IOC boot was not done by OS driver, force IOC state
to BFI_IOC_UNINIT
- Unused macro and API cleanup
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change Details:
- Call netif_wake_queue() if we have freed up sufficient elements
at the end of completion processing
- Add netif_queue_stopped counter back to bnad_drv_stats {}
- Get netif_queue_stopped value from stack
- Remove BUG_ON() on value returned by pci_unmap_addr()
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change Details:
- Enable reception of pure priority tagged packets by default by
turning on VLAN Id = 0
- Clear the promiscuous mode, all multicast mode flags when
bna_rxf_uninit is called
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change Details:
- Removed semaphore register dump from ethtool
- Moved netif_carrier_off() call to before calling bna_init()
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change Details:
- Fixed port enable/disable sync through a change in LL port state
machine
- Change txq->priority masking to 0x7 (3 bits) from 0x3 (2 bits)
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change Details:
- Check HW ready condition before accessing h/w register in data-path
- Postpone clean-up of data buffers to the data-path restart path and
wait in the cleanup routines for in-flight DMA to complete
- Separate out Tx completion processing from Rx poll routine
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The X540 introduces a new Virtual Function device ID so that the X540
VF device can be distinguished from the 82599 VF device. The X540 VF
device will have additional capability over the 82599 VF device so it
is necessary to be able to discern the difference.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for the anti-spoofing feature in the HW. Packets from
VF devices with spoofed MAC addresses or VLAN tags will be blocked
and a counter incremented. During the watchdog timer the spoofed
packet dropped counter is read and if it is non-zero then a warning
message is displayed on the host VMM's console.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add X540 specific feature support to X540
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Print warnings to the system log when the VF attempts to override
MAC/VLAN settings that were configured by the VMM Host administrator
using the ip link set commands.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support to igbvf for the new i350 virtual function device.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change forces the link down when a mailbox timeout has occurred.
Previously it was possible for a mailbox timeout to occur but for the
interface to stay up. The problem with this was that it became possible
for an interface to stay up and miss multiple requests resulting in a
possible issue since the interface will be running in an unknown state.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for the anti-spoofing feature in the HW. Packets from
VF devices with spoofed MAC addresses or VLAN tags will be blocked
and an event generated. When the watchdog task runs it will call a
function to check if any spoof events occurred. If an event was
detected then a warning message is dumped to the system log.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch does the following:
1. Changes the existing supported device id's so now DH89xxCC is not supported when EEPROM is not read.
2. Adds two more device ids for DH89xxCC in backplane mode and SFP.
3. Driver now initializes previously possibly uninitialized value in igb_reset_mdicnfg_82580().
Signed-off-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Print a warning message to the system log when the VF attempts to
override administratively set MAC/VLAN configuration.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The vf flags were being overwritten causing the flag that indicates
that the PF has set the VF MAC address to get cleared. This would
allow the VF to override the MAC address assigned by the Host VMM
using the ip link set command.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
WARNING: braces {} are not necessary for any arm of this statement
WARNING: braces {} are not necessary for single statement blocks
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ERROR: that open brace { should be on the previous line
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ERROR: trailing statements should be on next line
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ERROR: Macros with complex values should be enclosed in parenthesis
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
pci_restore_state only ever returns 0, thus there is no benefit in
having it return any value. Also, a large majority of the callers do
not check the return code of pci_restore_state. Make the
pci_restore_state a void return and avoid the overhead.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
- Connection ID (cid) management
- Slow-path command and response support
- Update version to 2.2.11.
Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kcq2 (2nd kernel work queue) is used by FCoE on 57712 devices.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we get a path_resp error from userspace, call cm_connect_complete()
immediately with error so that bnx2i can react to the error faster.
Signed-off-by: Eddie Wai <waie@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the device is down, the kcq pointer may be NULL.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a common function cnic_read_bnx2x_iscsi_mac() to read the iSCSI
MAC address at any specified shared memory location. In NIC Partition
mode, we need to get the MAC address from the MF_CFG area of shared
memory.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the IDs specified by the bnx2x driver when initializing the ring.
We don't have to make code changes when these IDs change in the future.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Change first parameter from cnic_dev to ulp_handle which is the hba
pointer. All other similar upcalls are using hba pointer. The callee
can then directly reference the hba without conversion.
2. Change return value from void to int so that an error code can be
passed back. This allows the operation to be retried.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cnic_dev_list is protected by rtnl_lock and cnic_dev_lock spin_lock during
modifications. When looping on cnic_dev_list and calling ->cnic_init(),
we should just hold rtnl_lock since ->cnic_init() may sleep.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the TCP port parameter for iSCSI connections to the firmware in
proper endian order.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original code returns 0 on success and 1 on failure. In fact, at
this point, "ret" is already either zero or a negative error code so
we can just return it directly.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The atl1c driver uses the legacy PCI power management, so it has to
do some PCI-specific things in its ->suspend() and ->resume()
callbacks and they are not done correctly.
Convert atl1c to the new PCI power management framework and make it
let the PCI subsystem handle all of the PCI-specific aspects of
device handling during system power transitions.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
An RX buffer is set to 9100 bytes to receive 8K AMSDU; however, an skb
of this size fails in the kernel.
Signed-off-by: Chaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It looks like some hardware registers are left into undefined state
after suspend/resume. At minimum, this can cause odd issues related to
key cache and hardware trying to encrypt/decrypt frames unexpectedly.
This seems to happen even when there is no keys configured, i.e., hardware
can end up touching TX frames just based of invalid key cache context
even if the driver is not asking a specific entry to be used. In
addition, RX can likely be affected. This patch fixes this issue.
Signed-off-by: Jouni Malinen <Jouni.Malinen@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the radio enable switch is off when the driver is loaded, it is not
possible to get radio output until the driver is unloaded and reloaded
with the switch on.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Device poller already reads current RSSI, so add support for
set_cqm_rssi_config there.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Radio should be off when interface is down.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rndis_set_default_key did call add_wep_key to set default key on device, even
if key is WPA. This caused rndis_wlan not work with wpa_supplicant in nl80211
mode (causing disconnect from AP).
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes device returns wrong number of items in bssid-list. Appears that
some specific beacons trigger this problem and leads to very poor scanning
results. Workaround by ignoring num_items received from device and walkthrough
full bssid-list buffer.
v2: Fix buffer range checks and reading next item length. Old code read
behind buffer on last item but didn't use those values as 'count' would
also reach zero. Also fix resizing of buffer if device has larger buffer,
old code assumed that BSSID-list OID would return same buffer size
when it really can return yet another new larger length.
Tested-by: Luís Picciochi <Pitxyoki@gmail.com>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The size of the eeprom data is 1088 bytes for AR9485. But
a sanity check is done against 4K which would result in a
'potential read past the end of the buffer' smatch complaint.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce a helper function to get the EEPROM mode from channel and remove
multiple similar switch statements. Also since it's now easy to get the EEPROM
mode from the channel, use them inside the functions which need it, instead of
passing a redundant ee_mode parameter.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove redundant defines.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new variable to keep track of the currently configured tx power. Before
max_pwr was re-used for keeping the maximum allowed power as well as the
current configuration. Doing a min() on it allows you to lower the txpower, but
how would you be able to make it higher again?
This patch fixes that by adding a new variable ah_cur_pwr which is used instead
of txp_max_pwr to keep the current configuration. txp_max_pwr is used to check
if we are within the limits.
Another problem fixed by this patch is that it avoids setting a zero txpower
when things are initialized first and the current power is not yet set.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
And rename functions which write the powertable to make it clearer.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Let ath5k_hw_txpower() decide if it can re-use the powertable or if it has to
be recalculated instead of passing a 'fast' flag from the outside.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a missing unlock when we hit the "No beacon slot available"
error condition.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use function pci_pcie_cap() instead of accessing struct member directly.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use function pci_is_pcie() instead of accessing struct member directly.
CC: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use function pci_is_pcie() instead of accessing struct member directly.
CC: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use function pci_is_pcie() instead of accessing struct member directly.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No function declared in gpio.h is used here.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No function declared in gpio.h is used here.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k supports its own set of virtual wiphys, and it uses
the mac80211 idle notifications to know when a device needs
to be idle or not. We recently changed ath9k to force idle
on driver stop() and on resume but forgot to take into account
ath9k's own virtual wiphy idle states. These are used internally
by ath9k to check if the device's radio should be powered down
on each idle call. Without this change its possible that the
device could have been forced off but the virtual wiphy idle
was left on.
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k_hw: warn if we cannot change the power to the chip"
introduced a new warning to indicate chip powerup failures, but this
is not required for devices that have been removed. Handle USB device
removal properly by checking for unplugged status.
For PCI devices, this warning will still be seen when the card is pulled
out, not sure how to check for card removal.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These drivers share one header file, but nothing else. Worse, both
drivers use the rtl8225 part with different register settings. The
results has been some ugly naming -- let's simplify that.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
Suffix the U5500 modem IRQ and MBOX files with *-db5500* so that
we clearly know the SoC they belong to, in line with the rest of
the files in mach-ux500.
Cc: Stefan Nilsson <stefan.xk.nilsson@stericsson.com>
Cc: Martin Persson <martin.persson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Program adapter's StationAddress register when changing device MAC address
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wrap up acceess to ASICCtrl high word with a macro
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael pointed out that bnx2_close() already cancels bp->reset_task
and thus it is guaranteed to be idle when bnx2_remove_one() is called.
Remove the unnecessary cancel_work_sync() in remove_one.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original code had a several problems:
*) It had potential null dereferences of "priv" and "res".
*) It released the memory region before it was aquired.
*) It didn't free "ndev" after it was allocated.
*) It didn't call unregister_netdev() after calling stmmac_probe().
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We dereferenced params on the line before so it's too late to check if
params is NULL. In fact, params can never be NULL and strict_cos is
either 0 or 1 so that part of the check is bogus too. Let's remove it.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.
Signed-off-by: Joe Perches <joe@perches.com>
Moves the PCI table to the right read-only section.
Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.
Signed-off-by: Joe Perches <joe@perches.com>
Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.
Consolidate duplicated code into new fix_crc_bug function
and declare data in that function static const.
Signed-off-by: Joe Perches <joe@perches.com>
Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.
Signed-off-by: Joe Perches <joe@perches.com>
create_workqueue is deprecated. The workqueue usage does not seem to
demand any special treatment, so do not set any flags either.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Tejun Heo <tj@kernel.org>
Restricting the chainmask to 1 for legacy mode disables useful features
such as MRC, and it reduces the available transmit power.
I can't think of a good reason to do this in legacy mode, so let's just
get rid of that code.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit 'ath9k_hw: Disable PAPRD for rates with low Tx power' changed
the code that sets the PAPRD rate masks to use only either the HT20 mask
or the HT40 mask. This is wrong, as the hardware can still use HT20 rates
even when configured for HT40, and the operating channel mode does not
affect PAPRD operation.
The register for the HT40 rate mask is applied as a mask on top of the
other registers to selectively disable PAPRD for specific rates on HT40
packets only.
This patch changes the code back to the old behavior which matches the
intended use of these registers. While with current cards this should not
make any practical difference (according to Atheros, the HT20 and HT40
mask should always be equal), it is more correct that way, and maybe
the HT40 mask will be used for some rare corner cases in the future.
Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl12xx_get_platform_data() returns an ERR_PTR on failure and it never
returns a NULL.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A previous conversion from semaphoreto mutexes missed the fact that one
of the semaphores was used in interrupt code. Fixed by changing to
a spinlock.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k channel table for 2Ghz does not seems to initialize the 'band'
parameter.Though it does not seems to cause any visible issue it looks
odd when we initialize the 'band' parameter for 5Ghz channel table while
not so for 2Ghz.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When rfkill is enabled, ath9k_hw unnecessarily configured the baseband to
turn off based on GPIO input, however that code was hardcoded to GPIO 0
instead of ah->rfkill_gpio.
Since ath9k uses software rfkill anyway, this code is completely unnecessary
and should be removed in case anything else ever uses GPIO 0.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To improve aggregation length, there should not be more than two fully formed
A-MPDU frames in the hardware queue. To ensure this, the code checks the tx
queue length before forming new A-MPDUs. This can reduce the throughput (or
maybe even starve out A-MPDU traffic) when too many non-aggregated frames are
in the queue.
Fix this by keeping track of pending A-MPDU frames (even when they're sent out
as single frames), but exclude rate control probing frames to improve
performance.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix runtime warning with backtrace from hostap by removing
netif_stop_queue() call before register_netdev. Tested to work fine on
hostap_pci Prism 2.5.
(This removes a warning about calling netif_stop_queue before
register_netdev is called. -- JWL)
Signed-off-by: Meelis Roos <mroos@linux.ee>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All rt2x00 drivers except rt2800pci call ieee80211_tx_status() from
a workqueue, which causes "NOHZ: local_softirq_pending 08" messages.
To fix it, add ieee80211_tx_status_ni() similar to ieee80211_rx_ni()
which can be called from process context, and call it from
rt2x00lib_txdone(). For the rt2800pci special case a driver
flag is introduced.
https://bugzilla.kernel.org/show_bug.cgi?id=24892
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There were several paths that didn't release their locks.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
info->version only has space for 32 characters but my UTS_RELEASE is
"2.6.37-rc6-next-20101217-05817-ge935fc8-dirty" so it doesn't fit.
This is supposed to be the version of the driver, not the kernel
version. This driver doesn't have a version so lets just leave it
blank.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to active notification of the new MCS7832 version by the manufacturer
(Mr. Milton; thanks!) -- quote: "functionality same as MCS7830",
I'm now submitting this patch (on -rc6), intended for networking.git and -stable.
- add MCS7832 USB PID to be able to support this new device variant, too
- add related descriptions
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there are some info message that is set as error, and an error
message that is set as debug. This patch just fixes it.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6e07ebd84 (drivers/net: remove unnecessary
flush_scheduled_work() calls) incorrectly removed the flush call
without replacing it with the appropriate work specific operation.
Fix it by flushing vdev->reset_task explicitly.
Pointed out by Jon Mason.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jon Mason <jon.mason@exar.com>
Acked-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ri_tasklet(), we run from softirq, so can directly handle packet
through netif_receive_skb() instead of netif_rx().
There is no risk of recursion.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Logitec LAN-GTJ U2A (http://www.pro.logitec.co.jp/pro/g/gLAN-GTJU2A/)
USB 2.0 10/10/1000 Ethernet adapter is based on ASIX AX88178 chipset.
This patch adds missing USB ID for the device.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some boot code drivers dont have cleanup routine, so pci function
remains in unknown state prior to driver load. So during driver load
issue FLR unconditionally.
Update driver version to 5.0.14.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OCM window register offset was calculated incorrectly for
pci function greater than zero.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When interface is down, create temporary context to config LED.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My conversion of tehuti to use request_firmware() was confused about
the filename of the firmware blob. Change the driver to match the
blob.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
After recent ifb changes, we must use lockless __skb_dequeue() since
lock is not anymore initialized.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jamal Hadi Salim <hadi@cyberus.ca>
Cc: Changli Gao <xiaosuo@gmail.com>
Acked-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers are using skb_transport_offset(skb) instead of skb->csum_start
for NETIF_F_HW_CSUM offload. This does not matter now, but if someone
implements checksumming of encapsulated packets then this will break silently.
TSO output paths are left as they are, since they are for IP+TCP only
(might be worth converting though).
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace skb->csum_start - skb_headroom(skb) with skb_checksum_start_offset().
Note for usb/smsc95xx: skb->data - skb->head == skb_headroom(skb).
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't change ip_summed from CHECKSUM_PARTIAL to CHECKSUM_NONE
or CHECKSUM_UNNECESSARY because checksum in packet's headers is
not valid and will cause invalid checksum when frame is forwarded.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the mbox polling uses the schedule_timeout, the mbox_lock should be
a mutex and not a spin lock.
The commit f25b03a replaced udelay() with schedule_timeout() but didn't
change mbox_lock to semaphore or mutex.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provices the debugfs interface to see RLB hash table
like the following:
# cat /sys/kernel/debug/bonding/bond0/rlb_hash_table
SourceIP DestinationIP Destination MAC DEV
10.124.196.205 10.124.196.205 ff:ff:ff:ff:ff:ff eth4
10.124.196.205 10.124.196.81 00:19:99:XX:XX:XX eth3
10.124.196.205 10.124.196.1 00:21:d8:XX:XX:XX eth0
This is helpful to check if the receive load balancing works as expected.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch simply migrates some macros from bond_alb.c to bond_alb.h.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate Tx queue memory on the node indicated by the new
netdev_queue_numa_node_read.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current code parses the VPD RO section for keywords but makes static
assumptions about the location of the section. Remove them and parse
the VPD to find it.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch originally from Joe Perches, unmodified.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver keeps a bitmap of the netdevs it registered so it knows what to
unregister later. Remove that and look at reg_state instead.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a field the driver uses to keep track of the name of the first
netdev it manages to register. Do this by changing the registration
loop to stop the first time it fails so the first registered device is
trivial to tell.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The last byte of the buffer for MSI-X names could not be used due to a
bogus -1. Also do not explicitly clear the last byte, snprintf will do
the right thing.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently MSI-X names for netdevs with long names are truncated in
/proc/interrupts due to insufficient space. Use IFNAMSIZ to size the
needed space.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print information about each port when its netdev is registered instead
of looping separately over the ports at the end. The bulk of this patch
is due to indentation change.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And fix the supported flags ethtool reports for the two cases.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of queues is known early, move the calls to
netif_set_real_num_[rt]x_queues before register_netdev.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to read the clock frequency from VPD, we already get it a bit
later from FW, after any potential adjustments.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable relaxed ordering for descriptor reads and packet I/O.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Includes FCoE releated fixes in FW flows
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding DCB initialization and handling on 57712 FW/HW
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Shmulik Ravid-Rabinovitz <shmulikr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This callback required to allow FCoE traffic to be
sent on separate priority queue from other L2 traffic,
which is managed by PFC in HW.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Shmulik Ravid-Rabinovitz <shmulikr@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Includes new driver structures and FW/HW configuration for FCoE ring
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Shmulik Ravid-Rabinovitz <shmulikr@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bond_na_send() attempts to insert a VLAN tag in between building and
sending packets of the respective formats. If the slave does not
implement hardware VLAN tag insertion then vlan_put_tag() will mangle
the network-layer header because the Ethernet header is not present at
this point (unlike in bond_arp_send()).
Fix this by adding the tag out-of-line and relying on
dev_hard_start_xmit() to insert it inline if necessary.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bond_change_active_slave() may be called when a slave is added, even
if the bond has not been brought up yet. It may then attempt to send
packets, and further it may use mcast_work which is uninitialised
before the bond is brought up. Add the necessary checks for
netif_running(bond->dev).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A bond may have a mixture of slave devices with and without hardware
VLAN tag insertion capability. Therefore it always claims this
capability and performs software VLAN tag insertion if the slave does
not.
Since commit 7b9c609037, this has
also been done by dev_hard_start_xmit(). The result is that VLAN-
tagged skbs are now double-tagged when transmitted through slave
devices without hardware VLAN tag insertion!
Remove the now-redundant logic from bond_dev_queue_xmit().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
axnet_cs:
Accton EN2328 or compatible (id: 0x01bf, 0x2328) uses Asix chip.
So it works better with axnet_cs instead of pcnet_cs.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
The returned slave is incorrect, if the net device under check is not
charged yet by the master.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The old survey implementation was broken and returned nonsense data.
Clear cycle counters and survey data on reset. Since the cycle counters easily
overflow it's better to keep a local version of collected survey data (in ms
resolution, instead of clockrate) and update this every time survey is
retrieved. If survey is retrieved often enough to avoid cycle counter overflows
this works fine, otherwise we could update survey more often, like ath9k does.
Still only the survey for the current channel is kept.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After merge of the rtl8192ce driver, a powerpc build fails with:
drivers/net/wireless/rtlwifi/rtl8192ce/rtl8192c-sw.c: In function 'rtl92c_init_sw_vars':
drivers/net/wireless/rtlwifi/rtl8192ce/rtl8192c-sw.c:76: error: implicit declaration of function 'vmalloc'
drivers/net/wireless/rtlwifi/rtl8192ce/rtl8192c-sw.c:76: warning: cast to pointer from integer of different size
drivers/net/wireless/rtlwifi/rtl8192ce/rtl8192c-sw.c: In function 'rtl92c_deinit_sw_vars':
drivers/net/wireless/rtlwifi/rtl8192ce/rtl8192c-sw.c:91: error: implicit declaration of function 'vfree'
The problem is fixed by explicitly including the appropriate header.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Target Tx power available in eeprom is for PAPRD. If PAPRD
fails, paprd scale factor needs to be detected from this
target tx power.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the drop in Tx power for a particular mcs rate exceeds
the paprd scale factor, paprd may not work properly. Disable
paprd for any such rates.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add multiple Tx IQ cal support to improve EVM accross
different power levels.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This helper can be used in multiple places. Also make
it inline returning u8.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* usb-next: (132 commits)
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
usb: gadget: f_ncm.c added
usb: gadget: u_ether: prepare for NCM
usb: pch_udc: Fix setup transfers with data out
usb: pch_udc: Fix compile error, warnings and checkpatch warnings
usb: add ab8500 usb transceiver driver
USB: gadget: Implement runtime PM for MSM bus glue driver
USB: gadget: Implement runtime PM for ci13xxx gadget
USB: gadget: Add USB controller driver for MSM SoC
USB: gadget: Introduce ci13xxx_udc_driver struct
USB: gadget: Initialize ci13xxx gadget device's coherent DMA mask
USB: gadget: Fix "scheduling while atomic" bugs in ci13xxx_udc
USB: gadget: Separate out PCI bus code from ci13xxx_udc
...
While compiling linux-next (next-20101216) I fell over this breakage:
...
drivers/net/wireless/iwlwifi/iwl-agn-rs.c: In function ‘iwl_rs_rate_init’:
drivers/net/wireless/iwlwifi/iwl-agn-rs.c:2876:8: error: ‘struct iwl_lq_sta’ has no member named ‘dbg_fixed_rate’
dbg_fixed_rate is only used when CONFIG_MAC80211_DEBUGFS is set:
[ drivers/net/wireless/iwlwifi/iwl-agn-rs.h ]
...
#ifdef CONFIG_MAC80211_DEBUGFS
struct dentry *rs_sta_dbgfs_scale_table_file;
struct dentry *rs_sta_dbgfs_stats_table_file;
struct dentry *rs_sta_dbgfs_rate_scale_data_file;
struct dentry *rs_sta_dbgfs_tx_agg_tid_en_file;
u32 dbg_fixed_rate;
#endif
The issue was introduced by commit a1da077bc36368eb7d6312e7e49260f0a3d92c77:
"iwlwifi: clear dbg_fixed_rate during init"
Signed-off-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PM-QOS value can be user specified via module parameter.
This patch adds few comments regarding this in the driver
code.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not required for USB devices.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow drivers or rate control algorithms to specify BlockAck session
timeout when initiating an ADDBA transaction. This is useful in cases
where maintaining persistent BA sessions does not incur any overhead.
The current timeout value of 5000 TUs is retained for all non ath9k/ath9k_htc
drivers.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
patch "iwlagn: check ready in iwlagn_bss_info_changed()" introduce
whitespace, fix it
please merge with the previous patch
Reported by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch allows the pm-qos value to be user configurable by making it as
a module parameter.This will help our customers to configure the pm-qos
value according to the effect in throughput due to the DMA latency problem
which was observed in Intel Pinetrail platforms.
The tested value of '55' will be filled as the default
pm-qos-value incase the user does not specifies pm-qos value as a
module parameter.
example usage: sudo modprobe ath9k pmqos=65
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Without this, gcc 4.5 won't compile xen-netfront and xen-blkfront, where
this is being used to specify array sizes.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: David Miller <davem@davemloft.net>
Cc: Stable Kernel <stable@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change some file names and Kconfig settings so that this new module matches
the new way of using wl12xx instead of wl1271.
Also fix SDIO power enabling and disabling to match the latest way of doing
it.
Cc: Roger Quadros <roger.quadros@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
With the current single-queue implementation traffic priorization is not
working correctly - when using multiple BE streams and one, say VI stream,
the VI stream will share bandwidth almost equally with the BE streams.
To fix the issue, implement per AC queues, which are emptied in priority
order to the firmware. To keep it relatively simple, maintain a global
buffer count and global queue stop/wake instead of per-AC.
With these changes, priorization appears to work just fine.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Currently, the debug level is set in compilation time (by the DEBUG_LEVEL
const). This method has the advantage of compiling only the relevant
messages, while optimizing out the unused ones.
In order to allow runtime control over the debug_level, while optimizing
out messages when debug messages are not needed, we combine some methods:
1. use dynamic_debug (pr_debug) rather then printk.
2. add debug_level module param in order to set debug level during insmod.
3. add debug_level sysfs file in order to allow dynamic control over the
debug level.
Since patches for pr_debug_hex_dump() implementation haven't been applied yet,
we are still temporarly using print_hex_dump().
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Inclusion of a WPS IE in probe requests caused a problem
in the driver due to the maximum size of the probe request
template and the max_scan_ie_len values at initialization.
Increased the size of probe request template
to the maximum size allowed by the firmware.
Struct wl12xx_probe_req_template, which was only used
for calculating the max size of the probe request template,
is no longer used and needed.
max_scan_ie_len is used for validating the size of
additional IEs in scan requests.
Initialized the max_scan_ie_len field to the maximum size
of the probe request template minus the ieee80211 header size.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
The auto-arp feature of wl12xx allows the firmware to automatically
response to arp requests asking for its ip.
in order to use it, we configure the arp response template and
enable the corresponding bit in wl1271_acx_arp_filter (along with
passing its ip)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
This module enables individually generating RX and TX traffic
over the SDIO bus on which the WL1271 chipset is connected.
This is required to perform RF interference testing.
The module takes 2 module parameters 'rx' and 'tx'.
To generate RX traffic:
modprobe wl1271_sdio_test rx=1
To generate TX traffic:
modprobe wl1271_sdio_test tx=1
To generate both RX & TX traffic, set both rx and tx to 1.
You can change the testing configuration at runtime by changing
the rx & tx values at /sys/modules/wl1271_sdio_test/
To stop testing simply unload the module.
Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Reviewed-by: Carlos Chinea <carlos.chinea@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Disabling the 11a channels when not supported in the reg_notify function was
not working as it should, because when the driver is initiailizing (and
registering itself with mac80211), it would get the reg notification too
early. At that point the driver wouldn't have received the NVS yet, so it
wouldn't know whether 11a was supported.
To fix this, we disable 11a channels when we read the NVS instead. Also, it
is easier (and still safe) to set n_channels to zero instead of setting the
disabled flag on every 11a channel.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
cancel_rearming_delayed_work[queue]() has been superceded by
cancel_delayed_work_sync() quite some time ago. Convert all the
in-kernel users. The conversions are completely equivalent and
trivial.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: "David S. Miller" <davem@davemloft.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: netdev@vger.kernel.org
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Neil Brown <neilb@suse.de>
Cc: Alex Elder <aelder@sgi.com>
Cc: xfs-masters@oss.sgi.com
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: netfilter-devel@vger.kernel.org
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: linux-nfs@vger.kernel.org
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (75 commits)
pppoe.c: Fix kernel panic caused by __pppoe_xmit
WAN: Fix a TX IRQ causing BUG() in PC300 and PCI200SYN drivers.
bnx2x: Advance a version number to 1.60.01-0
bnx2x: Fixed a compilation warning
bnx2x: LSO code was broken on BE platforms
qlge: Fix deadlock when cancelling worker.
net: fix skb_defer_rx_timestamp()
cxgb4vf: Ingress Queue Entry Size needs to be 64 bytes
phy: add the IC+ IP1001 driver
atm: correct sysfs 'device' link creation and parent relationships
MAINTAINERS: remove me from tulip
SCTP: Fix SCTP_SET_PEER_PRIMARY_ADDR to accpet v4mapped address
enic: Bug Fix: Pass napi reference to the isr that services receive queue
ipv6: fix nl group when advertising a new link
connector: add module alias
net: Document the kernel_recvmsg() function
r8169: Fix runtime power management
hso: IP checksuming doesn't work on GE0301 option cards
xfrm: Fix xfrm_state_migrate leak
net: Convert netpoll blocking api in bonding driver to be a counter
...
This USB ID is for the WUBI-100GW 802.11g Wireless LAN USB Device that
uses p54usb.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Eduardo Costa <ecosta.tmp@gmail.com>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Multiple devices use almost the same .cfg with minor differences.
Use macro and remove the duplication. By doing this, reduce
the chance for mistake while modify .cfg parameters
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
For WiFi/WiMAX combo devices, if WiMAX own the RF, WiFi driver
try to access RF and fail. This is the W/A to To avoid WiFi keep
reloading firmware and try to access RF again.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
For logging EEPROM related info, instead of using IWL_DEBUG_INFO,
use the dedicated logging (IWL_DEBUG_EEPROM) for easier debugging
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This removes the old TX power reading code, it isn't
necessary since the new code is able to read all the
various EEPROM layouts due to relying on information
contained in the EEPROM.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The current EEPROM reading code has some layout
assumptions that now turned out to be false with
some newer versions of the EEPROM. Luckily, we
can avoid all such assumptions by using data in
the EEPROM itself, so implement using that.
However, for risk mitigation purposes, keep the
old reading code for current hardware for now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Some fields we didn't previously use from the
enhanced TX power structure will be needed in
the next patch, so rename them to their correct
names to be able to use them and change code
reading them accordingly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
For the new 1x1 devices, hw and uCode will support rx
antenna diversity, but we need to indicate 1x1 device to
AccessPoint to make sure it won't use MIMO.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The compiler correctly warns:
iwl-agn-tx.c: In function ‘iwlagn_tx_status_reply_compressed_ba’:
iwl-agn-tx.c:1240: warning: ‘bitmap’ may be used uninitialized in this function
Move the debug print to the branch that reads the
bitmap, and move the variables too so it's more
obvious where they are needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
In function iwlagn_bss_info_changed(), we need to check if the driver
is ready before doing real work. Also, the previously put WARN() is
removed because the vif is not guaranteed to be valid. uCode restart
routine will clear the vif.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This prevent bad fixed_rate keeps crashing uCode in an endless loop.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Since this driver is implemented as NAPI,
netif_receive_skb must be used not netif_rx.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add setting TEC/REC statistics processing.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For reduce "if" condition, easy to read/understand the code,
optimize "if" condition in rx/tx processing.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, in case this driver is integrated as module, and when this
module is re-installed, no interrupts is to be occurred.
For the above issue, move MSI processing to open/release processing.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify miss-setting status issue at suspend.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify like use calculated value directly passed by CAN core module.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix coding rule violation.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
For easy to readable, use netdev_dbg instead of dev_dbg partly
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, Copyright and module description are not formal.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For improve tx/rx speed, reduce register access.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, these two functions spec(returned value) is unnatural.
Thus, change the return value's spec
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For easy to read/understand, Rename function/macro name.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, in case CONFIG_PM is disabled, compiler outputs warnings.
Move six functions which are used only CONFIG_PM is enabled,
into "#ifdef CONFIG_PM" area.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace complex "goto" to "do~while".
For easy to read/understand, it divides a rx function into some functions.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
there is endianness issue both Tx and Rx.
Currently, data is set like below.
Register:
MSB--LSB
x x D0 D1
x x D2 D3
x x D4 D5
x x D6 D7
But Data to be sent must be set like below.
Register:
MSB--LSB
x x D1 D0
x x D3 D2
x x D5 D4
x x D7 D6 (x means reserved area.)
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To easy to read/understand, divide poll function into two sub-functions.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, there is no flow control processing.
Thus, Add flow control processing as
when there is no empty of tx buffer,
netif_stop_queue is called.
When there is empty buffer, netif_wake_queue is called.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6175ddf06b changes the way
memcpy_toio() works for x86_64, causing firmware loading to fail for
some Ralink WLAN devices with the rt2800pci driver since linux 2.6.34.
This causes the log message: "phy0 -> rt2800pci_load_firmware: Error -
PBF system register not ready.".
Fix this by using __iowrite32_copy instead of memcpy_toio().
Signed-off-by: Wolfgang Kufner <wolfgang.kufner@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pad beacon to a multiple of 32 bits in preparation for the change
from memcpy_toio() to __iowrite32_copy() in register_multiwrite().
Signed-off-by: Wolfgang Kufner <wolfgang.kufner@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The stray semicolon after DEBUG_PRINTK_MSG causes things
like "if (...) WARNING(...); else {}" to fail with syntax error.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Queue names were incorrectly copied from the legacy drivers,
as a result the queue names were inversed to what was expected.
This renames the queues using this mapping:
QID_AC_BK -> QID_AC_VO (priority 0)
QID_AC_BE -> QID_AC_VI (priority 1)
QID_AC_VI -> QID_AC_BE (priority 2)
QID_AC_VO -> QID_AC_BK (priority 3)
Note that this was a naming problem only, which didn't affect
the assignment of frames to their respective queues.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a queue entry flag ENTRY_DATA_STATUS_PENDING,
which can be used to indicate a queue entry has
returned from the hardware and is waiting for
status processing. Using this flag we can add
some extra sanity checks to prevent queue corruption.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the rt2x00_dmastart function to rt2x00lib which
marks the queue_entry as "owned by device", and increased
the Q_INDEX number.
This cleanups up the index handling by rt2x00lib which
at until so far used hackish approaches to keep the
RX queue index numbering sane.
The rt2x00pci.c changes are from Helmut Schaa
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new command to the queue handlers: "flush",
this moves the flush() callback from mac80211
into rt2x00queue and adds support for flushing
the RX queue as well.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add wrapper functions in rt2x00queue.c to
start & stop queues. This control must be protected
using a mutex.
Queues can also be paused which will halt the flow
of packets between the driver and mac80211. This doesn't
require a mutex protection.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As part of the queue refactoring, change the queue callback
function names to have 3 different actions: start, kick & stop.
We can now also remove the STATE_RADIO_RX_ON/STATE_RADIO_RX_OFF
device_state flags, and replace the usage with using the
start_queue/stop_queue callback functions.
This streamlines the RX queue handling to the
similar approach as all other queues.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As part of the queue refactoring, we now introduce
3 queue commands: start, kick, stop.
- Start: will enable a queue, for TX this will
not mean anything, while for beacons and RX
this will update the registers to enable the queue.
- Kick: This will kick all pending frames to
the hardware. This is needed for the TX queue
to push all frames to the HW after the queue
has been started
- Stop: This will stop the queue in the hardware,
and cancel any pending work (So this doesn't
mean the queue is empty after a stop!).
Move all code from the drivers into the appropriate
functions, and link those calls to the old rt2x00lib
callback functions (we will fix this later when we
refactor the queue control inside rt2x00lib).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 0204464329 "Check for specific changed
flags when updating the erp config" changed the way in which a new beacon
interval gets handled. However, due to a bug in rt2800usb and rt2800pci the
beacon interval was reset during each scan, thus causing problems in AdHoc
mode.
Fix this by not cleaning up the beacon interval when killing the beacon queue
but just prevent the device from sending out beacons.
Reported-by: Wolfgang Kufner <wolfgang.kufner@gmail.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recent changes to the TX-done code of rt2x00 resulted in TX-ed frames not
being returned to mac80211 in the original state, and therefore with
insufficient headroom for re-transmissions.
Fix this by reverting the changes done and by ensuring we remove the inserted
L2pad by moving the header backwards instead of the data forwards.
At the same time also make sure that the rt2x00queue_remove_l2pad will not
move any memory when a frame has no data at all.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Jay Hung <Jay_Hung@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an rt2x00 USB device is unplugged while in use, it reliably
hangs the whole system. After some time the watchdog prints:
BUG: soft lockup - CPU#0 stuck for 64s! [kworker/u:0:5]
...
[<c01a88d8>] (usb_submit_urb+0x0/0x2ac) from [<bf0e752c>] (rt2x00usb_kick_rx_entry+0xb4/0xe8 [rt2x00usb])
[<bf0e7478>] (rt2x00usb_kick_rx_entry+0x0/0xe8 [rt2x00usb]) from [<bf0e7588>] (rt2x00usb_clear_entry+x28/0x2c [rt2x00usb])
[<bf0e7560>] (rt2x00usb_clear_entry+0x0/0x2c [rt2x00usb]) from [<bf0d5bc4>] (rt2x00lib_rxdone+0x2e0/0x2f8 [rt2x00lib])
[<bf0d58e4>] (rt2x00lib_rxdone+0x0/0x2f8 [rt2x00lib]) from [<bf0e7e00>] (rt2x00usb_work_rxdone+0x54/0x74 [rt2x00usb])
[<bf0e7dac>] (rt2x00usb_work_rxdone+0x0/0x74 [rt2x00usb]) from [<c00542b4>] (process_one_work+0x20c/0x35c)
Clear the DEVICE_STATE_PRESENT flag when usb_submit_urb()
returns -ENODEV to fix this.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add RF chip definition
Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement the get_survey callback to allow user space to read statistics
about the current channel condition.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add and modify NIC Configuration and LED definition of EEPROM
Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reduces the likelihood of false pulse detects in the hardware
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The EEPROM contains scale factors for the tx power, which define
the range of allowable difference between target power and training
power. If the difference is too big, PA predistortion cannot be used.
For 2.4 GHz there is only one scale factor, for 5 GHz there are
three, depending on the specific frequency range.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The EEPROM PAPRD rate mask fields only contain mask values for actual
rates in the low 25 bits. The upper bits are reserved for tx power
scale values. Add the proper mask definitions and use them before
writing the values to the register.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To be able to measure the thermal values correctly for PAPRD, we need
to send training frames before setting up the gain table for the measurement,
and then again afterwards for the actual training.
For further improvement, send training frames at MCS0 instead of 54 MBit/s
legacy. That way we can use the No-ACK flag for the transmission, which
speeds up PAPRD training in general, as the hardware won't have to
retransmit and wait for ACK timeout (was previously set to 4 * 6
transmission attempts).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Testing shows that adjusting the slot time based on the coverage class
produces very high latencies and very low throughput on long distance links.
Adjusting only the ACK timeout and leaving the slot time at the regular
values - while technically not optimal for CSMA - works a lot better on
long links (tested with 10 km distance)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(u32) -1 is not particularly useful as a slottime default, so even though
the ath9k_hw default should never get used, it's better to pick something
sane here.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need to have separate callbacks for pre-AR9003 vs AR9003
SREV version checks, so just merge those into one function.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9280 based hardware with 3 antennas and slow antenna diversity has
not been seen in the wild and ath9k does not support that form of
antenna diversity, so remove the EEPROM ops for it.
These EEPROM ops are currently only used for setting the
AR_PHY_SWITCH_COM register, which is being done in the EEPROM specific
file already.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also add a comment about a potential array overrun that needs to
be reviewed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Newer chips do not need this, and maybe these register writes could have
negative side effects on newer hardware.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wireless-testing commit 04caf86375
('ath9k: more tx setup cleanups') merged tx path code for HT vs
non-HT frames, however it did not pass the tid pointer to
ath_tx_send_normal, causing an inconsistency between AMPDU vs
non-AMPDU sequence number handling.
Fix this by always passing in the tid pointer for all QoS data frames.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HW has to be awake when accessing registers.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As discussed we do not know band width at core reset time and it is not a good
idea to reset whole just to change band. So just set unconditionally 20 MHz
band width as default during core reset.
As for defines PHY clock changed to band width in specs and it makes much more
sens to call defines by band width which is self-explainable. Updated specs do
not mention 0 value, but comparing to old ones you can notice lineral relation
between PHY clock speed and band width. So it makes sense for 0x0 value to be
10 MHz band width.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace to specify that a given key
is default only for unicast and/or multicast
transmissions. Only WEP keys are for both,
WPA/RSN keys set here are GTKs for multicast
only. For more future flexibility, allow to
specify all combiations.
Wireless extensions can only set both so use
nl80211; WEP keys (connect keys) must be set
as default for both (but 802.1X WEP is still
possible).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The registers TBTT_TIMER ,DMA_BEACON_ALERT ,NEXT_SWBA are need to be
configured only for AP and IBSS mode.
SWBA register is used for generating software interrupts so that beacon
frames will be created by the software.DMA beacon alert register is
to indicate the hardware to DMA the contents of beacon buffer to PCU buffer
and TBTT to start transmitting the packet buffer to the base band.
Clearly these things are not needed for station/monitor mode so
remove configuring them.
Cc: doug dahlby <ddahlby@atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
key4 of micentry is used, if ATH_CRYPT_CAP_MIC_COMBINED is set.
But is not cleared on key cache reset.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support to change interface type
without bringing down the interface.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 will notify drivers when to go idle and ath9k
assumed that it would get further notifications for idle
states after a device stop() config call but as per agreed
semantics the idle state of the radio is left up to driver
after mac80211 issues the stop() callback. The driver is
resposnbile for ensuring the device remains idle after
that even between suspend / resume calls.
This fixes suspend/resume when you issue suspend and resume
twice on ath9k when ath9k_stop() was already called. We need
to put the radio to full sleep in order for resume to work
correctly.
What might seem fishy is we are turning the radio off
after resume. The reason why we do this is because we know
we should not have anything enabled after a mac80211 tells
us to stop(), if we resume and never get a start() we won't
get another stop() by mac80211 so to be safe always bring
the 802.11 device with the radio disabled after resume,
this ensures that if we suspend we already have the radio
disabled and only a start() will ever trigger it on.
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Upon a failure we never call ath9k_ps_restore() on ath_radio_enable(),
this will throw off the sc->ps_usecount. When the sc->ps_usecount
is > 0 we never put the chip to full sleep. This drains battery,
and will also make the chip fail upon resume with:
ath: Starting driver with initial channel: 5745 MHz
ath: timeout (100000 us) on reg 0x7000: 0xdeadbeef & 0x00000003 != 0x00000000
This would make the chip useless upon resume.
I cannot prove this can happen but in theory it is so best to
avoid this race completely and not have users complain about
a broken device after resume.
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code wants to check if there's a channel and it is not disabled,
but it used to check if channel is not NULL and accessed the channel
struct if this check failed.
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove ehea_error, ehea_info and ehea_debug macros.
Use pr_fmt, pr_<level>, netdev_<level> and netif_<level> as appropriate.
Fix messages to use trailing "\n", some messages had an extra one
as the old ehea_<level> macros added a trailing "\n".
Coalesced long format strings.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always go through a new ip4_dst_hoplimit() helper, just like ipv6.
This allowed several simplifications:
1) The interim dst_metric_hoplimit() can go as it's no longer
userd.
2) The sysctl_ip_default_ttl entry no longer needs to use
ipv4_doint_and_flush, since the sysctl is not cached in
routing cache metrics any longer.
3) ipv4_doint_and_flush no longer needs to be exported and
therefore can be marked static.
When ipv4_doint_and_flush_strategy was removed some time ago,
the external declaration in ip.h was mistakenly left around
so kill that off too.
We have to move the sysctl_ip_default_ttl declaration into
ipv4's route cache definition header net/route.h, because
currently net/ip.h (where the declaration lives now) has
a back dependency on net/route.h
Signed-off-by: David S. Miller <davem@davemloft.net>
__pppoe_xmit function return value was invalid resulting in
additional call to kfree_skb on already freed skb. This resulted in
memory corruption and consequent kernel panic after PPPoE peer
terminated the link.
This fixes commit 55c95e738d.
Reported-by: Gorik Van Steenberge <gvs@zemos.net>
Reported-by: Daniel Kenzelmann <kernel.bugzilla@kenzelmann.dyndns.info>
Reported-by: Denys Fedoryshchenko <nuclearcat@nuclearcat.com>
Reported-by: Pawel Staszewski <pstaszewski@artcom.pl>
Diagnosed-by: Andrej Ota <andrej@ota.si>
Diagnosed-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Denys Fedoryshchenko <nuclearcat@nuclearcat.com>
Tested-by: Pawel Staszewski <pstaszewski@artcom.pl>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: Andrej Ota <andrej@ota.si>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must not wake the TX queue without free TX descriptors.
sca_xmit() expects at least one free descriptor and BUGs otherwise.
Problem reported and fix tested by Bernie Innocenti and Ward Vandewege.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x_src_init_t2() is used only when BCM_CNIC is defined.
So, to avoid a compilation warning, we won't define it unless
BCM_CNIC is defined.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the LSO code work on BE platforms: parsing_data field of
a parsing BD (PBD) for 57712 was improperly composed which made FW read wrong
values for TCP header's length and offset and, as a result, the corresponding
PCI device was performing bad DMA reads triggering EEH.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing usage of rtnl_lock() to protect firmware interface registers.
These registers are accessed in some worker threads and can create a
deadlock if rtnl_lock is taken by upper layers while the worker is still
pending.
We remove rtnl_lock and use a driver mutex just while mailboxes are
accessed.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
flush_scheduled_work() is on its way out. Drop flush_scheduled_work()
from prism2_free_local_data() and replace it with explicit flushing of
work items on the respective free functions. Work items in ap_data
are flushed from hostap_free_data() and the ones in local_info from
prism2_free_local_data().
Flush is used instead of cancel as some process and free items from
queue.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jes Sorensen <jes@trained-monkey.org>
Cc: netdev@vger.kernel.org
i2400m implements dynamic work allocation and queueing mechanism in
i2400_schedule_work(); however, this is only used for reset and
recovery which can be served equally well with preallocated per device
works.
Replace i2400m_schedule_work() with two work structs in struct i2400m.
These works are explicitly canceled when the device is released making
calls to flush_scheduled_work(), which is being deprecated,
unnecessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: linux-wimax@intel.com
Cc: netdev@vger.kernel.org
gp->reset_task_pending is always set right before reset_task is
scheduled and as there is no synchronization between the setting and
scheduling, busy looping on reset_task_pending before flushing
reset_task doesn't really buy anything.
Directly flush gp->reset_task on suspend and cancel on detach.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
All three drivers use flush_scheduled_work() similarly during driver
detach. Replace it with explicit cancels.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: e1000-devel@lists.sourceforge.net
Cc: netdev@vger.kernel.org
flush_scheduled_work() is on its way out. Remove its usage from
iseries_veth.
* Cancelling a delayed work, queueing it for immediate execution if
cancelled and then waiting for completion can be done by simply
calling flush_delayed_work_sync().
* Explicitly cancel cnx->statemachine_wq on module unload.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Santiago Leon <santil@linux.vnet.ibm.com>
Cc: netdev@vger.kernel.org
Directly cancel port->reset_task from ehea_shutdown_single_port()
instead. As this cancels the work for each port on driver detach,
flushing system_wq from ehea_remove() or ehea_module_exit() is no
longer necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Breno Leitao <leitao@linux.vnet.ibm.com>
Cc: netdev@vger.kernel.org
ehea_rereg_mr_task is not used. Remove it and drop @work parameter
from ehea_rereg_mrs().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Breno Leitao <leitao@linux.vnet.ibm.com>
Cc: netdev@vger.kernel.org
flush_scheduled_work() is on its way out. This patch contains simple
conversions to replace flush_scheduled_work() usage with direct
cancels and flushes.
Directly cancel the used works on driver detach and flush them in
other cases.
The conversions are mostly straight forward and the only dangers are,
* Forgetting to cancel/flush one or more used works.
* Cancelling when a work should be flushed (ie. the work must be
executed once scheduled whether the driver is detaching or not).
I've gone over the changes multiple times but it would be much
appreciated if you can review with the above points in mind.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: Divy Le Ray <divy@chelsio.com>
Cc: e1000-devel@lists.sourceforge.net
Cc: Vasanthy Kolluri <vkolluri@cisco.com>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Andrew Gallatin <gallatin@myri.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: Ramkrishna Vepa <ramkrishna.vepa@exar.com>
Cc: Matt Carlson <mcarlson@broadcom.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: netdev@vger.kernel.org
janz-ican3, sh_eth, skge and vxge don't use workqueue at all and there
is no reason to flush the system_wq. Drop flush_scheduled_work()
calls and references to workqueue.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Ramkrishna Vepa <ramkrishna.vepa@exar.com>
Cc: Sivakumar Subramani <sivakumar.subramani@exar.com>
Cc: Sreenivasa Honnur <sreenivasa.honnur@exar.com>
Cc: Jon Mason <jon.mason@exar.com>
Cc: netdev@vger.kernel.org
The driver global au_macs[] is unused in the entire kernel tree,
so remove it.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
text data bss dec hex filename
109387 389 24432 134208 20c40 drivers/net/s2io.o.old
109358 389 24432 134179 20c23 drivers/net/s2io.o.new
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put immutable data in read/only section.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
modparm rx_ring_sz can be set to be greater than the maximum allowable
number of blocks. This results in an array overrun when probing the
driver, and causes memory corruption.
Also, the MAX_RX_DESC_1 multiply the max number of rings by max number
of blocker per ring by 127, but the driver does the same calculation
with 127+1. This results in the possibility of the value being set
being larger than the maximum allowable value.
Finally, clean-up the s2io_ethtool_gringparam code to be more
intuitive.
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New adapters will have part numbers stored in string format rather than
simple hex format. This function will read part number formats in either
hex or string.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shmulik Ravid