sk_backlog is a critical field of struct sock. (known famous words)
It is (ab)used in hot paths, in particular in release_sock(), tcp_recvmsg(),
tcp_v4_rcv(), sk_receive_skb().
It really makes sense to place it next to sk_lock, because sk_backlog is only
used after sk_lock locked (and thus memory cache line in L1 cache). This
should reduce cache misses and sk_lock acquisition time.
(In theory, we could only move the head pointer near sk_lock, and leaving tail
far away, because 'tail' is normally not so hot, but keep it simple :) )
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New sysctl tcp_frto_response is added to select amongst these
responses:
- Rate halving based; reuses CA_CWR state (default)
- Very conservative; used to be the only one available (=1)
- Undo cwr; undoes ssthresh and cwnd reductions (=2)
The response with rate halving requires a new parameter to
tcp_enter_cwr because FRTO has already reduced ssthresh and
doing a second reduction there has to be prevented. In addition,
to keep things nice on 80 cols screen, a local variable was
added.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
This interpretation comes from RFC4138:
"If the sender implements some loss recovery algorithm other
than Reno or NewReno [FHG04], the F-RTO algorithm SHOULD
NOT be entered when earlier fast recovery is underway."
I think the RFC means to say (especially in the light of
Appendix B) that ...recovery is underway (not just fast recovery)
or was underway when it was interrupted by an earlier (F-)RTO
that hasn't yet been resolved (snd_una has not advanced enough).
Thus, my interpretation is that whenever TCP has ever
retransmitted other than head, basic version cannot be used
because then the order assumptions which are used as FRTO basis
do not hold.
NewReno has only the head segment retransmitted at a time.
Therefore, walk up to the segment that has not been SACKed, if
that segment is not retransmitted nor anything before it, we know
for sure, that nothing after the non-SACKed segment should be
either. This assumption is valid because TCPCB_EVER_RETRANS does
not leave holes but each non-SACKed segment is rexmitted
in-order.
Check for retrans_out > 1 avoids more expensive walk through the
skb list, as we can know the result beforehand: F-RTO will not be
allowed.
SACKed skb can turn into non-SACked only in the extremely rare
case of SACK reneging, in this case we might fail to detect
retransmissions if there were them for any other than head. To
get rid of that feature, whole rexmit queue would have to be
walked (always) or FRTO should be prevented when SACK reneging
happens. Of course RTO should still trigger after reneging which
makes this issue even less likely to show up. And as long as the
response is as conservative as it's now, nothing bad happens even
then.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The input_device pointer is not refcounted, which means the device may
disappear while packets are queued, causing a crash when ifb passes packets
with a stale skb->dev pointer to netif_rx().
Fix by storing the interface index instead and do a lookup where neccessary.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg discovered that kernel space was leaking to
userspace on 64 bit platform. He made a first patch to fix that. This
is an improved version of his patch.
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As per RFC2461, section 6.3.6, item #2, when no routers on the
matching list are known to be reachable or probably reachable we
do round robin on those available routes so that we make sure
to probe as many of them as possible to detect when one becomes
reachable faster.
Each routing table has a rwlock protecting the tree and the linked
list of routes at each leaf. The round robin code executes during
lookup and thus with the rwlock taken as a reader. A small local
spinlock tries to provide protection but this does not work at all
for two reasons:
1) The round-robin list manipulation, as coded, goes like this (with
read lock held):
walk routes finding head and tail
spin_lock();
rotate list using head and tail
spin_unlock();
While one thread is rotating the list, another thread can
end up with stale values of head and tail and then proceed
to corrupt the list when it gets the lock. This ends up causing
the OOPS in fib6_add() later onthat many people have been hitting.
2) All the other code paths that run with the rwlock held as
a reader do not expect the list to change on them, they
expect it to remain completely fixed while they hold the
lock in that way.
So, simply stated, it is impossible to implement this correctly using
a manipulation of the list without violating the rwlock locking
semantics.
Reimplement using a per-fib6_node round-robin pointer. This way we
don't need to manipulate the list at all, and since the round-robin
pointer can only ever point to real existing entries we don't need
to perform any locking on the changing of the round-robin pointer
itself. We only need to reset the round-robin pointer to NULL when
the entry it is pointing to is removed.
The idea is from Thomas Graf and it is very similar to how this
was implemented before the advanced router selection code when in.
Signed-off-by: David S. Miller <davem@davemloft.net>
->neigh_destructor() is killed (not used), replaced with
->neigh_cleanup(), which is called when neighbor entry goes to dead
state. At this point everything is still valid: neigh->dev,
neigh->parms etc.
The device should guarantee that dead neighbor entries (neigh->dead !=
0) do not get private part initialized, otherwise nobody will cleanup
it.
I think this is enough for ipoib which is the only user of this thing.
Initialization private part of neighbor entries happens in ipib
start_xmit routine, which is not reached when device is down. But it
would be better to add explicit test for neigh->dead in any case.
Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon a patch from Patrick McHardy.
The fib_rules netlink attribute policy introduced in 2.6.19 broke
userspace compatibilty. When specifying a rule with "from all"
or "to all", iproute adds a zero byte long netlink attribute,
but the policy requires all addresses to have a size equal to
sizeof(struct in_addr)/sizeof(struct in6_addr), resulting in a
validation error.
Check attribute length of FRA_SRC/FRA_DST in the generic framework
by letting the family specific rules implementation provide the
length of an address. Report an error if address length is non
zero but no address attribute is provided. Fix actual bug by
checking address length for non-zero instead of relying on
availability of attribute.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the association has been restarted, we need to reset the
transport congestion variables as well as accumulated error
counts and CACC variables. If we do not, the association
will use the wrong values and may terminate prematurely.
This was found with a scenario where the peer restarted
the association when lksctp was in the last HB timeout for
its association. The restart happened, but the error counts
have not been reset and when the timeout occurred, a newly
restarted association was terminated due to excessive
retransmits.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During association restart we may have stale data sitting
on the ULP queue waiting for ordering or reassembly. This
data may cause severe problems if not cleaned up. In particular
stale data pending ordering may cause problems with receive
window exhaustion if our peer has decided to restart the
association.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The security hooks to check permissions to remove an xfrm_policy were
actually done after the policy was removed. Since the unlinking and
deletion are done in xfrm_policy_by* functions this moves the hooks
inside those 2 functions. There we have all the information needed to
do the security check and it can be done before the deletion. Since
auditing requires the result of that security check err has to be passed
back and forth from the xfrm_policy_by* functions.
This patch also fixes a bug where a deletion that failed the security
check could cause improper accounting on the xfrm_policy
(xfrm_get_policy didn't have a put on the exit path for the hold taken
by xfrm_policy_by*)
It also fixes the return code when no policy is found in
xfrm_add_pol_expire. In old code (at least back in the 2.6.18 days) err
wasn't used before the return when no policy is found and so the
initialization would cause err to be ENOENT. But since err has since
been used above when we don't get a policy back from the xfrm_policy_by*
function we would always return 0 instead of the intended ENOENT. Also
fixed some white space damage in the same area.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Venkat Yekkirala <vyekkirala@trustedcs.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts two changes:
8488df894d248f06726e
A backlog value of N really does mean allow "N + 1" connections
to queue to a listening socket. This allows one to specify
"0" as the backlog and still get 1 connection.
Noticed by Gerrit Renker and Rick Jones.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix {nf,ip}_ct_iterate_cleanup unconfirmed list handling:
- unconfirmed entries can not be killed manually, they are removed on
confirmation or final destruction of the conntrack entry, which means
we might iterate forever without making forward progress.
This can happen in combination with the conntrack event cache, which
holds a reference to the conntrack entry, which is only released when
the packet makes it all the way through the stack or a different
packet is handled.
- taking references to an unconfirmed entry and using it outside the
locked section doesn't work, the list entries are not refcounted and
another CPU might already be waiting to destroy the entry
What the code really wants to do is make sure the references of the hash
table to the selected conntrack entries are released, so they will be
destroyed once all references from skbs and the event cache are dropped.
Since unconfirmed entries haven't even entered the hash yet, simply mark
them as dying and skip confirmation based on that.
Reported and tested by Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
when I use linux TCP socket, and find there is a bug in function
sk_acceptq_is_full().
When a new SYN comes, TCP module first checks its validation. If valid,
send SYN,ACK to the client and add the sock to the syn hash table. Next
time if received the valid ACK for SYN,ACK from the client. server will
accept this connection and increase the sk->sk_ack_backlog -- which is
done in function tcp_check_req().We check wether acceptq is full in
function tcp_v4_syn_recv_sock().
Consider an example:
After listen(sockfd, 1) system call, sk->sk_max_ack_backlog is set to
1. As we know, sk->sk_ack_backlog is initialized to 0. Assuming accept()
system call is not invoked now.
1. 1st connection comes. invoke sk_acceptq_is_full(). sk-
>sk_ack_backlog=0 sk->sk_max_ack_backlog=1, function return 0 accept
this connection. Increase the sk->sk_ack_backlog
2. 2nd connection comes. invoke sk_acceptq_is_full(). sk-
>sk_ack_backlog=1 sk->sk_max_ack_backlog=1, function return 0 accept
this connection. Increase the sk->sk_ack_backlog
3. 3rd connection comes. invoke sk_acceptq_is_full(). sk-
>sk_ack_backlog=2 sk->sk_max_ack_backlog=1, function return 1. Refuse
this connection.
I think it has bugs. after listen system call. sk->sk_max_ack_backlog=1
but now it can accept 2 connections.
Signed-off-by: Wei Dong <weid@np.css.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ctnetlink uses netlink_unicast from an atomic_notifier_chain
(which is called within a RCU read side critical section)
without holding further locks. netlink_unicast calls netlink_trim
with the result of gfp_any() for the gfp flags, which are passed
down to pskb_expand_header. gfp_any() only checks for softirq
context and returns GFP_KERNEL, resulting in this warning:
BUG: sleeping function called from invalid context at mm/slab.c:3032
in_atomic():1, irqs_disabled():0
no locks held by rmmod/7010.
Call Trace:
[<ffffffff8109467f>] debug_show_held_locks+0x9/0xb
[<ffffffff8100b0b4>] __might_sleep+0xd9/0xdb
[<ffffffff810b5082>] __kmalloc+0x68/0x110
[<ffffffff811ba8f2>] pskb_expand_head+0x4d/0x13b
[<ffffffff81053147>] netlink_broadcast+0xa5/0x2e0
[<ffffffff881cd1d7>] :nfnetlink:nfnetlink_send+0x83/0x8a
[<ffffffff8834f6a6>] :nf_conntrack_netlink:ctnetlink_conntrack_event+0x94c/0x96a
[<ffffffff810624d6>] notifier_call_chain+0x29/0x3e
[<ffffffff8106251d>] atomic_notifier_call_chain+0x32/0x60
[<ffffffff881d266d>] :nf_conntrack:destroy_conntrack+0xa5/0x1d3
[<ffffffff881d194e>] :nf_conntrack:nf_ct_cleanup+0x8c/0x12c
[<ffffffff881d4614>] :nf_conntrack:kill_l3proto+0x0/0x13
[<ffffffff881d482a>] :nf_conntrack:nf_conntrack_l3proto_unregister+0x90/0x94
[<ffffffff883551b3>] :nf_conntrack_ipv4:nf_conntrack_l3proto_ipv4_fini+0x2b/0x5d
[<ffffffff8109d44f>] sys_delete_module+0x1b5/0x1e6
[<ffffffff8105f245>] trace_hardirqs_on_thunk+0x35/0x37
[<ffffffff8105911e>] system_call+0x7e/0x83
Since netlink_unicast is supposed to be callable from within RCU
read side critical sections, make gfp_any() check for in_atomic()
instead of in_softirq().
Additionally nfnetlink_send needs to use gfp_any() as well for the
call to netlink_broadcast).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds proper prototypes for some functions in
include/net/irda/irda.h
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes xfrm6_tunnel register and deregister
interface to prepare for solving the conflict of device
tunnels with inter address family IPsec tunnel.
There is no device which conflicts with IPv4 over IPv6
IPsec tunnel.
Signed-off-by: Kazunori MIYAZAWA <miyazawa@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes xfrm4_tunnel register and deregister
interface to prepare for solving the conflict of device
tunnels with inter address family IPsec tunnel.
Signed-off-by: Kazunori MIYAZAWA <miyazawa@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
No caller checks the return value, and since its usually called within the
module unload path there's nothing a module could do about errors anyway,
so BUG on invalid conditions and return void.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
NF_CT_STAT_INC assumes rcu_read_lock in nf_hook_slow disables
preemption as well, making it legal to use __get_cpu_var without
disabling preemption manually. The assumption is not correct anymore
with preemptable RCU, additionally we need to protect against softirqs
when not holding nf_conntrack_lock.
Add NF_CT_STAT_INC_ATOMIC macro, which disables local softirqs,
and use where necessary.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace preempt_{enable,disable} based RCU by proper use of the
RCU API and add missing rcu_read_lock/rcu_read_unlock calls in
all paths not obviously only used within packet process context
(nfnetlink_conntrack).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This last patch (but not least :) ) finally moves the next pointer at
the end of struct dst_entry. This permits to perform route cache
lookups with a minimal cost of one cache line per entry, instead of
two.
Both 32bits and 64bits platforms benefit from this new layout.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the next pointer from 'struct dn_route.u' union,
and renames u.rt_next to u.dst.dn_next.
It also moves 'struct flowi' right after 'struct dst_entry' to prepare
speedup lookups.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the next pointer from 'struct rt6_info.u' union,
and renames u.next to u.dst.rt6_next.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the rt_next pointer from 'struct rtable.u' union,
and renames u.rt_next to u.dst_rt_next.
It also moves 'struct flowi' right after 'struct dst_entry' to prepare
the gain on lookups.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces an anonymous union to nicely express the fact that all
objects inherited from struct dst_entry should access to the generic 'next'
pointer but with appropriate type verification.
This patch is a prereq before following patches.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ehash table layout is currently this one :
First half of this table is used by sockets not in TIME_WAIT state
Second half of it is used by sockets in TIME_WAIT state.
This is non optimal because of for a given hash or socket, the two chain heads
are located in separate cache lines.
Moreover the locks of the second half are never used.
If instead of this halving, we use two list heads in inet_ehash_bucket instead
of only one, we probably can avoid one cache miss, and reduce ram usage,
particularly if sizeof(rwlock_t) is big (various CONFIG_DEBUG_SPINLOCK,
CONFIG_DEBUG_LOCK_ALLOC settings). So we still halves the table but we keep
together related chains to speedup lookups and socket state change.
In this patch I did not try to align struct inet_ehash_bucket, but a future
patch could try to make this structure have a convenient size (a power of two
or a multiple of L1_CACHE_SIZE).
I guess rwlock will just vanish as soon as RCU is plugged into ehash :) , so
maybe we dont need to scratch our heads to align the bucket...
Note : In case struct inet_ehash_bucket is not a power of two, we could
probably change alloc_large_system_hash() (in case it use __get_free_pages())
to free the unused space. It currently allocates a big zone, but the last
quarter of it could be freed. Again, this should be a temporary 'problem'.
Patch tested on ipv4 tcp only, but should be OK for IPV6 and DCCP.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Jennifer Hunt <jenhunt@us.ibm.com>
This patch adds AF_IUCV socket support.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add rewritten IUCV base code to net/iucv.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
echo "1" > /proc/sys/net/x25/x25_forward
To turn on x25_forwarding, defaults to off
Requires the previous patch.
Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds call forwarding to X.25, allowing it to operate like an X.25 router.
Useful if one needs to manipulate X.25 traffic with tools like tc.
This is an update/cleanup based off a patch submitted by Daniel Ferenci a few years ago.
Thanks Alan for the feedback.
Added the null check to the clones.
Moved the skb_clone's into the forwarding functions.
Worked ok with Cisco XoT, linux X.25 back to back, and some old NTUs/PADs.
Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the XFRM framework so that endpoint address(es) in the XFRM
databases could be dynamically updated according to a request (MIGRATE
message) from user application. Target XFRM policy is first identified
by the selector in the MIGRATE message. Next, the endpoint addresses
of the matching templates and XFRM states are updated according to
the MIGRATE message.
Signed-off-by: Shinta Sugimoto <shinta.sugimoto@ericsson.com>
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to NAT to randomize source ports.
Signed-off-by: Eric Leblond <eric@inl.fr>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is nf_conntrack_sane, a netfilter connection tracking helper module
for the SANE protocol used by the 'saned' daemon to make scanners available
via network. The SANE protocol uses separate control & data connections,
similar to passive FTP. The helper module is needed to recognize the data
connection as RELATED to the control one.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch exports xfrm_state_afinfo.
Signed-off-by: Miika Komu <miika@iki.fi>
Signed-off-by: Diego Beltrami <Diego.Beltrami@hiit.fi>
Signed-off-by: Kazunori Miyazawa <miyazawa@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do this even for non-blocking sockets. This avoids the silly -EAGAIN
that applications can see now, even for non-blocking sockets in some
cases (f.e. connect()).
With help from Venkat Tekkirala.
Signed-off-by: David S. Miller <davem@davemloft.net>
The tcphdr struct passed to tcp_v4_check is not used, the following
patch removes it from the parameter list.
This adds the netfilter modifications missing in the patch I sent
for rc3-mm1.
Signed-off-by: Frederik Deweerdt <frederik.deweerdt@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revert 931731123a
We can't elide the skb_set_owner_w() here because things like certain
netfilter targets (such as owner MATCH) need a socket to be set on the
SKB for correct operation.
Thanks to Jan Engelhardt and other netfilter list members for
pointing this out.
Signed-off-by: David S. Miller <davem@davemloft.net>
Consider the chunk as Out-of-the-Blue if we don't have
an endpoint. Otherwise discard it as before.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In file included from net/netfilter/xt_state.c:13:
include/net/netfilter/nf_conntrack_compat.h: In function 'nf_ct_l3proto_try_module_get':
include/net/netfilter/nf_conntrack_compat.h:70: error: 'PF_INET' undeclared (first use in this function)
include/net/netfilter/nf_conntrack_compat.h:70: error: (Each undeclared identifier is reported only once
include/net/netfilter/nf_conntrack_compat.h:70: error: for each function it appears in.)
include/net/netfilter/nf_conntrack_compat.h:71: warning: control reaches end of non-void function
make[2]: *** [net/netfilter/xt_state.o] Error 1
make[1]: *** [net/netfilter] Error 2
make: *** [net] Error 2
A simple fix is to have nf_conntrack_compat.h #include <linux/socket.h>.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts the new (unambiguous) definition of the TCP `before'
relation. As pointed out in an example by Herbert Xu, there is
existing code which implicitly requires the old definition in order
to work correctly.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a proper prototype for x25_init_timers() in
include/net/x25.h
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The WLAN_GET_SEQ_SEQ(seq) macro in ieee80211 is selecting the wrong region.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes the following needlessly global functions static:
- ipv6.c: sctp_inet6addr_event()
- protocol.c: sctp_inetaddr_event()
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ivan Skytte Jorgensen <isj-sctp@i1.dk>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While looking at DCCP sequence numbers, I stumbled over a problem with
the following definition of before in tcp.h:
static inline int before(__u32 seq1, __u32 seq2)
{
return (__s32)(seq1-seq2) < 0;
}
Problem: This definition suffers from an an ambiguity, i.e. always
before(a, (a + 2^31) % 2^32)) = 1
before((a + 2^31) % 2^32), a) = 1
In text: when the difference between a and b amounts to 2^31,
a is always considered `before' b, the function can not decide.
The reason is that implicitly 0 is `before' 1 ... 2^31-1 ... 2^31
Solution: There is a simple fix, by defining before in such a way that
0 is no longer `before' 2^31, i.e. 0 `before' 1 ... 2^31-1
By not using the middle between 0 and 2^32, before can be made
unambiguous.
This is achieved by testing whether seq2-seq1 > 0 (using signed
32-bit arithmetic).
I attach a patch to codify this. Also the `after' relation is basically
a redefinition of `before', it is now defined as a macro after before.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
rose_add_loopback_neigh uses kmalloc and the callers were ignoring the
error value. Rewrite to let the caller deal with the allocation. This
allows the use of static allocation of kmalloc use entirely.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ax25_linkfail_register uses kmalloc and the callers were ignoring the
error value. Rewrite to let the caller deal with the allocation. This
allows the use of static allocation of kmalloc use entirely.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace ax25_protocol_register by ax25_register_pid which assumes the
caller has done the memory allocation. This allows replacing the
kmalloc allocations entirely by static allocations.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent fix 0506d4068b made obvious that
error values were not being propagated through the AX.25 stack. To help
with that this patch marks all kmalloc users in the AX.25, NETROM and
ROSE stacks as __must_check.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make fib6_node 'subtree' depend on IPV6_SUBTREES.
Signed-off-by: Kim Nordlund <kim.nordlund@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ivan Skytte Jorgensen <isj-sctp@i1.dk>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently in SCTP, we maintain a local address list by rebuilding the whole
list from the device list whenever we get a address add/delete event.
This patch fixes it by only adding/deleting the address for which we
receive the event.
Also removed the sctp_local_addr_lock() which is no longer needed as we
now use list_for_each_safe() to traverse this list. This fixes the bugs
in sctp_copy_laddrs_xxx() routines where we do copy_to_user() while
holding this lock.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To do that, this makes nf_ct_l3proto_try_module_{get,put} compatible
functions. As a result we can remove '#ifdef' surrounds and direct call of
need_conntrack().
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix foobar in 15b1c0e822 and
e8cc49bb0f patch series.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the callsign but not the SSID part of an AX.25 address is ASCII
based but Linux by initializes the SSID which should be just a 4-bit
number from ASCII anyway.
Fix that and convert the code to use a shared constant for both default
addresses. While at it, use the same style for null_ax25_address also.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hard header cache is in the main output path, so using
seqlock instead of reader/writer lock should reduce overhead.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the core of the switch to the new framework. I've split it from the
driver patches which are mostly search/replace and would encourage people to
give this one a good hard stare.
The references to BOTHER and ISHIFT are the termios values that must be
defined by a platform once it wants to turn on "new style" ioctl support. The
code patches here ensure that providing
1. The termios overlays the ktermios in memory
2. The only new kernel only fields are c_ispeed/c_ospeed (or none)
the existing behaviour is retained. This is true for the patches at this
point in time.
Future patches will define BOTHER, ISHIFT and enable newer termios structures
for each architecture, and once they are all done some of the ifdefs also
vanish.
[akpm@osdl.org: warning fix]
[akpm@osdl.org: IRDA fix]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Stick NFS sockets in their own class to avoid some lockdep warnings. NFS
sockets are never exposed to user-space, and will hence not trigger certain
code paths that would otherwise pose deadlock scenarios.
[akpm@osdl.org: cleanups]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Steven Dickson <SteveD@redhat.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Acked-by: Neil Brown <neilb@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
[ Fixed patch corruption by quilt, pointed out by Peter Zijlstra ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace all uses of kmem_cache_t with struct kmem_cache.
The patch was generated using the following script:
#!/bin/sh
#
# Replace one string by another in all the kernel sources.
#
set -e
for file in `find * -name "*.c" -o -name "*.h"|xargs grep -l $1`; do
quilt add $file
sed -e "1,\$s/$1/$2/g" $file >/tmp/$$
mv /tmp/$$ $file
quilt refresh
done
The script was run like this
sh replace kmem_cache_t "struct kmem_cache"
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_ATOMIC is an alias of GFP_ATOMIC
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Disables auditing in ipsec when CONFIG_AUDITSYSCALL is
disabled in the kernel.
Also includes a bug fix for xfrm_state.c as a result of
original ipsec audit patch.
Signed-off-by: Joy Latten <latten@austin.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
An audit message occurs when an ipsec SA
or ipsec policy is created/deleted.
Signed-off-by: Joy Latten <latten@austin.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
include/net/irda/irlan_filter.h:31: warning: 'struct seq_file' declared inside parameter list
include/net/irda/irlan_filter.h:31: warning: its scope is only this definition or declaration, which is probably not what you want
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/ata/libata-scsi.c
include/linux/libata.h
Futher merge of Linus's head and compilation fixups.
Signed-Off-By: David Howells <dhowells@redhat.com>
Conflicts:
drivers/infiniband/core/iwcm.c
drivers/net/chelsio/cxgb2.c
drivers/net/wireless/bcm43xx/bcm43xx_main.c
drivers/net/wireless/prism54/islpci_eth.c
drivers/usb/core/hub.h
drivers/usb/input/hid-core.c
net/core/netpoll.c
Fix up merge failures with Linus's head and fix new compilation failures.
Signed-Off-By: David Howells <dhowells@redhat.com>
Add nf_conntrack port of the PPtP conntrack/NAT helper. Since there seems
to be no IPv6-capable PPtP implementation the helper only support IPv4.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IPv4 and IPv6 capable nf_conntrack port of the H.323 conntrack/NAT helper.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expectation address masks need to be differently initialized depending
on the address family, create helper function to avoid cluttering up
the code too much.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add FTP NAT helper.
Split out from Jozsef's big nf_nat patch with a few small fixes by myself.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add NAT support for nf_conntrack. Joint work of Jozsef Kadlecsik,
Yasuyuki Kozakai, Martin Josefsson and myself.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some helpers (namely H.323) manually assign further helpers to expected
connections. This is not possible with nf_conntrack anymore since we
need to know whether a helper is used at allocation time.
Handle the helper assignment centrally, which allows to perform the
correct allocation and as a nice side effect eliminates the need
for the H.323 helper to fiddle with nf_conntrack_lock.
Mid term the allocation scheme really needs to be redesigned since
we do both the helper and expectation lookup _twice_ for every new
connection.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resync with Al Viro's ip_conntrack annotations and fix a missed
spot in ip_nat_proto_icmp.c.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding the alignment to the size doesn't make any sense, what it
should do is align the size of the conntrack structure to the
alignment requirements of the helper structure and return an
aligned pointer in nfct_help().
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove assumption that generic netlink commands cannot have dump
completion callbacks.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Miika Komu <miika@iki.fi>
Signed-off-by: Diego Beltrami <Diego.Beltrami@hiit.fi>
Signed-off-by: Kazunori Miyazawa <miyazawa@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are multiple problems related to qlen adjustment that can lead
to an upper qdisc getting out of sync with the real number of packets
queued, leading to endless dequeueing attempts by the upper layer code.
All qdiscs must maintain an accurate q.qlen counter. There are basically
two groups of operations affecting the qlen: operations that propagate
down the tree (enqueue, dequeue, requeue, drop, reset) beginning at the
root qdisc and operations only affecting a subtree or single qdisc
(change, graft, delete class). Since qlen changes during operations from
the second group don't propagate to ancestor qdiscs, their qlen values
become desynchronized.
This patch adds a function to propagate qlen changes up the qdisc tree,
optionally calling a callback function to perform qdisc-internal
maintenance when the child qdisc becomes empty. The follow-up patches
will convert all qdiscs to use this function where necessary.
Noticed by Timo Steinbach <tsteinbach@astaro.com>.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set parent classids in default qdiscs to allow walking up the tree
from outside the qdiscs. This is needed by the next patch.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original NetLabel category bitmap was a straight char bitmap which worked
fine for the initial release as it only supported 240 bits due to limitations
in the CIPSO restricted bitmap tag (tag type 0x01). This patch converts that
straight char bitmap into an extensibile/sparse bitmap in order to lay the
foundation for other CIPSO tag types and protocols.
This patch also has a nice side effect in that all of the security attributes
passed by NetLabel into the LSM are now in a format which is in the host's
native byte/bit ordering which makes the LSM specific code much simpler; look
at the changes in security/selinux/ss/ebitmap.c as an example.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
We usually uses 'xxx_find_get' for function which increments
reference count.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch adds /proc/net/ip_conntrack, /proc/net/ip_conntrack_expect and
/proc/net/stat/ip_conntrack files to keep old programs using them working.
The /proc/net/ip_conntrack and /proc/net/ip_conntrack_expect files show only
IPv4 entries, the /proc/net/stat/ip_conntrack shows global statistics.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Add helper functions for sysctl registration with optional instantiating
of common path elements (like net/netfilter) and use it for support for
automatic registation of conntrack protocol sysctls.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Remove unused struct list_head from struct nf_conntrack_l3proto and
nf_conntrack_l4proto as all protocols are kept in arrays, not linked
lists.
Signed-off-by: Martin Josefsson <gandalf@wlug.westbo.se>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Add some more sanity checks when registering/unregistering l3/l4 protocols.
Signed-off-by: Martin Josefsson <gandalf@wlug.westbo.se>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Rename 'struct nf_conntrack_protocol' to 'struct nf_conntrack_l4proto' in
order to help distinguish it from 'struct nf_conntrack_l3proto'. It gets
rather confusing with 'nf_conntrack_protocol'.
Signed-off-by: Martin Josefsson <gandalf@wlug.westbo.se>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch splits out the event cache into its own file
nf_conntrack_ecache.c
Signed-off-by: Martin Josefsson <gandalf@wlug.westbo.se>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch splits out handling of helpers into its own file
nf_conntrack_helper.c
Signed-off-by: Martin Josefsson <gandalf@wlug.westbo.se>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch splits out expectation handling into its own file
nf_conntrack_expect.c
Signed-off-by: Martin Josefsson <gandalf@wlug.westbo.se>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch consolidates set/getsockopt code between UDP(-Lite) v4 and 6. The
justification is that UDP(-Lite) is a transport-layer protocol and therefore
the socket option code (at least in theory) should be AF-independent.
Furthermore, there is the following code reduplication:
* do_udp{,v6}_getsockopt is 100% identical between v4 and v6
* do_udp{,v6}_setsockopt is identical up to the following differerence
--v4 in contrast to v4 additionally allows the experimental encapsulation
types UDP_ENCAP_ESPINUDP and UDP_ENCAP_ESPINUDP_NON_IKE
--the remainder is identical between v4 and v6
I believe that this difference is of little relevance.
The advantages in not duplicating twice almost completely identical code.
The patch further simplifies the interface of udp{,v6}_push_pending_frames,
since for the second argument (struct udp_sock *up) it always holds that
up = udp_sk(sk); where sk is the first function argument.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extends the netlink interface to support the __le16 type and
converts address addition, deletion and, dumping to use the
new netlink interface.
Fixes multiple occasions of possible illegal memory references
due to not validated netlink attributes.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
switched to taking a pointer to net-endian sctp_addr
and a net-endian port number. Instances and callers
adjusted; interestingly enough, the only calls are
direct calls of specific instances - the method is not
used at all.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add sctp_chunk->source, sctp_sockaddr_entry->a, sctp_transport->ipaddr
and sctp_transport->saddr, maintain them as net-endian mirrors of
their host-endian counterparts.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Part 1: rename sctp_chunk->source, sctp_sockaddr_entry->a,
sctp_transport->ipaddr and sctp_transport->saddr (to ..._h)
The next patch will reintroduce these fields and keep them as
net-endian mirrors of the original (renamed) ones. Split in
two patches to make sure that we hadn't forgotten any instanes.
Later in the series we'll eliminate uses of host-endian variants
(basically switching users to net-endian counterparts as we
progress through that mess). Then host-endian ones will die.
Other embedded host-endian sctp_addr will be easier to switch
directly, so we leave them alone for now.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
That's going to be a long series. Introduced temporary helpers
doing copy-and-convert for sctp_addr; they are used to kill
flip-in-place in global data structures and will be used
to gradually push host-endian uses of sctp_addr out of existence.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
argument stored for SCTP_CMD_INIT_FAILED is always __be16
(protocol error). Introduced new field and accessor for
it (SCTP_PERR()); switched to their use (from SCTP_U32() and
.u32)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes two needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CIPSOv4 engine currently has MLS label limits which are slightly larger
than what the draft allows. This is not a major problem due to the current
implementation but we should fix this so it doesn't bite us later.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
The existing netlbl_lsm_secattr struct required the LSM to check all of the
fields to determine if any security attributes were present resulting in a lot
of work in the common case of no attributes. This patch adds a 'flags' field
which is used to indicate which attributes are present in the structure; this
should allow the LSM to do a quick comparison to determine if the structure
holds any security attributes.
Example:
if (netlbl_lsm_secattr->flags)
/* security attributes present */
else
/* NO security attributes present */
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
The netlbl_secattr_init() function would always return 0 making it pointless
to have a return value. This patch changes the function to return void.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
There were a few places in the NetLabel code where the int type was being used
instead of the gfp_t type, this patch corrects this mistake.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
Spotted by Ian McDonald, tentatively fixed by Gerrit Renker:
http://www.mail-archive.com/dccp%40vger.kernel.org/msg00599.html
Rewritten not to unroll sk_receive_skb, in the common case, i.e. no lock
debugging, its optimized away.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This is a revision of the previously submitted patch, which alters
the way files are organized and compiled in the following manner:
* UDP and UDP-Lite now use separate object files
* source file dependencies resolved via header files
net/ipv{4,6}/udp_impl.h
* order of inclusion files in udp.c/udplite.c adapted
accordingly
[NET/IPv4]: Support for the UDP-Lite protocol (RFC 3828)
This patch adds support for UDP-Lite to the IPv4 stack, provided as an
extension to the existing UDPv4 code:
* generic routines are all located in net/ipv4/udp.c
* UDP-Lite specific routines are in net/ipv4/udplite.c
* MIB/statistics support in /proc/net/snmp and /proc/net/udplite
* shared API with extensions for partial checksum coverage
[NET/IPv6]: Extension for UDP-Lite over IPv6
It extends the existing UDPv6 code base with support for UDP-Lite
in the same manner as per UDPv4. In particular,
* UDPv6 generic and shared code is in net/ipv6/udp.c
* UDP-Litev6 specific extensions are in net/ipv6/udplite.c
* MIB/statistics support in /proc/net/snmp6 and /proc/net/udplite6
* support for IPV6_ADDRFORM
* aligned the coding style of protocol initialisation with af_inet6.c
* made the error handling in udpv6_queue_rcv_skb consistent;
to return `-1' on error on all error cases
* consolidation of shared code
[NET]: UDP-Lite Documentation and basic XFRM/Netfilter support
The UDP-Lite patch further provides
* API documentation for UDP-Lite
* basic xfrm support
* basic netfilter support for IPv4 and IPv6 (LOG target)
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
By modyfing genlmsg_put() to take a genl_family and by adding
genlmsg_put_reply() the process of constructing the netlink
and generic netlink headers is simplified.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A generic netlink user has no interest in knowing how to
address the source of the original request.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Throughout the TCP/DCCP (and tunnelling) code, it often happens that the
return code of a transmit function needs to be tested against NET_XMIT_CN
which is a value that does not indicate a strict error condition.
This patch uses a macro for these recurring situations which is consistent
with the already existing macro net_xmit_errno, saving on duplicated code.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Account for the netlink message header size directly in nlmsg_new()
instead of relying on the caller calculate it correctly.
Replaces error handling of message construction functions when
constructing notifications with bug traps since a failure implies
a bug in calculating the size of the skb.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The data itself is already charged to the SKB, doing
the skb_set_owner_w() just generates a lot of noise and
extra atomics we don't really need.
Lmbench improvements on lat_tcp are minimal:
before:
TCP latency using localhost: 23.2701 microseconds
TCP latency using localhost: 23.1994 microseconds
TCP latency using localhost: 23.2257 microseconds
after:
TCP latency using localhost: 22.8380 microseconds
TCP latency using localhost: 22.9465 microseconds
TCP latency using localhost: 22.8462 microseconds
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow normal users to only choose among a restricted set of congestion
control choices. The default is reno and what ever has been configured
as default. But the policy can be changed by administrator at any time.
For example, to allow any choice:
cp /proc/sys/net/ipv4/tcp_available_congestion_control \
/proc/sys/net/ipv4/tcp_allowed_congestion_control
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create /proc/sys/net/ipv4/tcp_available_congestion_control
that reflects currently available TCP choices.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
An alternate solution would be to make the digest a pointer, allocate
it in sctp_endpoint_init() and free it in sctp_endpoint_destroy().
I guess I should have originally done it this way...
CC [M] net/sctp/sm_make_chunk.o
net/sctp/sm_make_chunk.c: In function 'sctp_unpack_cookie':
net/sctp/sm_make_chunk.c:1358: warning: initialization discards qualifiers from pointer target type
The reason is that sctp_unpack_cookie() takes a const struct
sctp_endpoint and modifies the digest in it (digest being embedded in
the struct, not a pointer). Make digest a pointer to fix this
warning.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Acked-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently allocate a fixed size (TCP_SYNQ_HSIZE=512) slots hash table for
each LISTEN socket, regardless of various parameters (listen backlog for
example)
On x86_64, this means order-1 allocations (might fail), even for 'small'
sockets, expecting few connections. On the contrary, a huge server wanting a
backlog of 50000 is slowed down a bit because of this fixed limit.
This patch makes the sizing of listen hash table a dynamic parameter,
depending of :
- net.core.somaxconn tunable (default is 128)
- net.ipv4.tcp_max_syn_backlog tunable (default : 256, 1024 or 128)
- backlog value given by user application (2nd parameter of listen())
For large allocations (bigger than PAGE_SIZE), we use vmalloc() instead of
kmalloc().
We still limit memory allocation with the two existing tunables (somaxconn &
tcp_max_syn_backlog). So for standard setups, this patch actually reduce RAM
usage.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the attribute policy for the non-specific attributes into
net/fib_rules.h and include it in the respective protocols.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move mark selector currently implemented per protocol into
the protocol independant part.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all protocols have been made aware of the mark
field it can be moved out of the union thus simplyfing
its usage.
The config options in the IPv4/IPv6/DECnet subsystems
to enable respectively disable mark based routing only
obfuscate the code with ifdefs, the cost for the
additional comparison in the flow key is insignificant,
and most distributions have all these options enabled
by default anyway. Therefore it makes sense to remove
the config options and enable mark based routing by
default.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix SO_PEERSEC for tcp sockets to return the security context of
the peer (as represented by the SA from the peer) as opposed to the
SA used by the local/source socket.
Signed-off-by: Venkat Yekkirala <vyekkirala@TrustedCS.com>
Signed-off-by: James Morris <jmorris@namei.org>
In the SoftMAC version of the IEEE 802.11 stack, not all duplicate messages are
detected. For the most part, there is no difficulty; however for TKIP and CCMP
encryption, the duplicates result in a "replay detected" log message where the
received and previous values of the TSC are identical. This change adds a new
variable to the ieee80211_device structure that holds the 'seq_ctl' value for
the previous frame. When a new frame repeats the value, the frame is dropped and
the appropriate counter is incremented.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a host_strip_iv_icv flag to ieee80211 which indicates that
ieee80211_rx should strip the IV/ICV/other security features from the payload.
This saves on some memmove() calls in the driver and seems like something that
belongs in the stack as it can be used by bcm43xx, ipw2200, and zd1211rw
I will submit the ipw2200 patch separately as it needs testing.
This patch also adds some sensible variable reuse (idx vs keyidx) in
ieee80211_rx
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Restoring old, correct comment for sk_filter_release, moving it to
where it should actually be, and changing new comment into proper
comment for sk_filter_rcu_free, where it actually makes sense.
The original fix submitted for this on Oct 23 mistakenly documented
the wrong function.
Signed-off-by: Paul Bonser <misterpib@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the work_struct pointer to the work function rather than context data.
The work function can use container_of() to work out the data.
For the cases where the container of the work_struct may go away the moment the
pending bit is cleared, it is made possible to defer the release of the
structure by deferring the clearing of the pending bit.
To make this work, an extra flag is introduced into the management side of the
work_struct. This governs auto-release of the structure upon execution.
Ordinarily, the work queue executor would release the work_struct for further
scheduling or deallocation by clearing the pending bit prior to jumping to the
work function. This means that, unless the driver makes some guarantee itself
that the work_struct won't go away, the work function may not access anything
else in the work_struct or its container lest they be deallocated.. This is a
problem if the auxiliary data is taken away (as done by the last patch).
However, if the pending bit is *not* cleared before jumping to the work
function, then the work function *may* access the work_struct and its container
with no problems. But then the work function must itself release the
work_struct by calling work_release().
In most cases, automatic release is fine, so this is the default. Special
initiators exist for the non-auto-release case (ending in _NAR).
Signed-Off-By: David Howells <dhowells@redhat.com>
This change makes __beXX available to user-space applications, such as
ipvsadm, which include ip_vs.h
Signed-Off-By: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
__constant_htons(2<<4) is not a replacement for
htonl(2<<20).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calculation of IPX checksum got buggered about 2.4.0. The old variant
mangled the packet; that got fixed, but calculation itself got buggered.
Restored the correct logics, fixed a subtle breakage we used to have even
back then: if the sum is 0 mod 0xffff, we want to return 0, not 0xffff.
The latter has special meaning for IPX (cheksum disabled). Observation
(and obvious fix) nicked from history of FreeBSD ipx_cksum.c...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix kernel-doc warning in include/net/sock.h:
Warning(/var/linsrc/linux-2619-rc1-pv//include/net/sock.h:894): No description found for parameter 'rcu'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
As suggested by David, just kill off some unused fields in dnports to
reduce sizef(struct flowi). If they come back, they should be moved to
nl_u.dn_u in order not to enlarge again struct flowi
[ Modified to really delete this stuff instead of using #if 0. -DaveM ]
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lot of routers/embedded devices still use CPUS with 16/32 bytes cache
lines. (486, Pentium, ... PIII) It makes sense to group together
fields used at lookup time so they fit in one cache line. This reduce
cache footprint and speedup lookups.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Struct pol_chain has existed since at least the 2.2 kernel, but isn't used
anymore. As the IPv6 policy routing is implemented in a totally different
way in the current kernel, just get rid of it.
Signed-off-by: Ville Nuorvala <vnuorval@tcs.hut.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet
Patrick McHardy