This patch allows the guest to enable the VMXE bit in CR4, which is a
prerequisite to running VMXON.
Whether to allow setting the VMXE bit now depends on the architecture (svm
or vmx), so its checking has moved to kvm_x86_ops->set_cr4(). This function
now returns an int: If kvm_x86_ops->set_cr4() returns 1, __kvm_set_cr4()
will also return 1, and this will cause kvm_set_cr4() will throw a #GP.
Turning on the VMXE bit is allowed only when the nested VMX feature is
enabled, and turning it off is forbidden after a vmxon.
Signed-off-by: Nadav Har'El <nyh@il.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch allows a guest to use the VMXON and VMXOFF instructions, and
emulates them accordingly. Basically this amounts to checking some
prerequisites, and then remembering whether the guest has enabled or disabled
VMX operation.
Signed-off-by: Nadav Har'El <nyh@il.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch adds to kvm_intel a module option "nested". This option controls
whether the guest can use VMX instructions, i.e., whether we allow nested
virtualization. A similar, but separate, option already exists for the
SVM module.
This option currently defaults to 0, meaning that nested VMX must be
explicitly enabled by giving nested=1. When nested VMX matures, the default
should probably be changed to enable nested VMX by default - just like
nested SVM is currently enabled by default.
Signed-off-by: Nadav Har'El <nyh@il.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
During tracing the emulator, we noticed that init_emulate_ctxt()
sometimes took a bit longer time than we expected.
This patch is for mitigating the problem by some degree.
By looking into the function, we soon notice that it clears the whole
decode_cache whose size is about 2.5K bytes now. Furthermore, most of
the bytes are taken for the two read_cache arrays, which are used only
by a few instructions.
Considering the fact that we are not assuming the cache arrays have
been cleared when we store actual data, we do not need to clear the
arrays: 2K bytes elimination. In addition, we can avoid clearing the
fetch_cache and regs arrays.
This patch changes the initialization not to clear the arrays.
On our 64-bit host, init_emulate_ctxt() becomes 0.3 to 0.5us faster with
this patch applied.
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Cc: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Use a local pointer to the emulate_ctxt for simplicity. Then, arrange
the hard-to-read mode selection lines neatly.
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: Avi Kivity <avi@redhat.com>
So far kvm_arch_vcpu_setup is responsible for freeing the vcpu struct if
it fails. Move this confusing resonsibility back into the hands of
kvm_vm_ioctl_create_vcpu. Only kvm_arch_vcpu_setup of x86 is affected,
all other archs cannot fail.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
In VMX, before we bring down a CPU we must VMCLEAR all VMCSs loaded on it
because (at least in theory) the processor might not have written all of its
content back to memory. Since a patch from June 26, 2008, this is done using
a per-cpu "vcpus_on_cpu" linked list of vcpus loaded on each CPU.
The problem is that with nested VMX, we no longer have the concept of a
vcpu being loaded on a cpu: A vcpu has multiple VMCSs (one for L1, a pool for
L2s), and each of those may be have been last loaded on a different cpu.
So instead of linking the vcpus, we link the VMCSs, using a new structure
loaded_vmcs. This structure contains the VMCS, and the information pertaining
to its loading on a specific cpu (namely, the cpu number, and whether it
was already launched on this cpu once). In nested we will also use the same
structure to hold L2 VMCSs, and vmx->loaded_vmcs is a pointer to the
currently active VMCS.
Signed-off-by: Nadav Har'El <nyh@il.ibm.com>
Acked-by: Acked-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Instead of blacklisting known-unsupported cpuid leaves, whitelist known-
supported leaves. This is more conservative and prevents us from reporting
features we don't support. Also whitelist a few more leaves while at it.
Signed-off-by: Avi Kivity <avi@redhat.com>
Acked-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Cleanup the same operation between kvm_mmu_page_unlink_children and
mmu_pte_write_zap_pte
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Parent pte rmap and page rmap are very similar, so use the same arithmetic
for them
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Abstract the operation of rmap to spte_list, then we can use it for the
reverse mapping of parent pte in the later patch
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Fix:
warning: ‘cs_sel’ may be used uninitialized in this function
warning: ‘ss_sel’ may be used uninitialized in this function
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Simply use __copy_to_user/__clear_user to write guest page since we have
already verified the user address when the memslot is set
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Simply return from kvm_mmu_pte_write path if no shadow page is
write-protected, then we can avoid to walk all shadow pages and hold
mmu-lock
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
vmcs_readl() and friends are really short, but gcc thinks they are long because of
the out-of-line exception handlers. Mark them always_inline to clear the
misunderstanding.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
We clean up a failed VMREAD by clearing the output register. Do
it in the exception handler instead of unconditionally. This is
worthwhile since there are more than a hundred call sites.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Dereference it in the actual users.
This not only cleans up the emulator but also makes it easy to convert
the old emulation functions to the new em_xxx() form later.
Note: Remove some inline keywords to let the compiler decide inlining.
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Dereference it in the actual users: only do_insn_fetch_byte().
This is consistent with the way __linearize() dereferences it.
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
The two macros need special care to use:
Assume rc, ctxt, ops and done exist outside of them.
Can goto outside.
Considering the fact that these are used only in decode functions,
moving these right after do_insn_fetch() seems to be a right thing
to improve the readability.
We also rename do_fetch_insn_byte() to do_insn_fetch_byte() to be
consistent.
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
The macro MIN_MEMORY_BLOCK_SIZE is currently defined twice in two .c
files, and I need it in a third one to fix a powerpc bug, so let's
first move it into a header
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Removing __init from check_platform_magic since it is called by
xen_unplug_emulated_devices in non-init contexts (It probably gets inlined
because of -finline-functions-called-once, removing __init is more to avoid
mismatch being reported).
Signed-off-by: Raghavendra D Prabhu <rprabhu@wnohang.net>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
In the past we would only use the function's value if the
returned value was not equal to 'acpi_sci_override_gsi'. Meaning
that the INT_SRV_OVR values for global and source irq were different.
But it is OK to use the function's value even when the global
and source irq are the same.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
In the past (2.6.38) the 'xen_allocate_pirq_gsi' would allocate
an entry in a Linux IRQ -> {XEN_IRQ, type, event, ..} array. All
of that has been removed in 2.6.39 and the Xen IRQ subsystem uses
an linked list that is populated when the call to
'xen_allocate_irq_gsi' (universally done from any of the xen_bind_*
calls) is done. The 'xen_allocate_pirq_gsi' is a NOP and there is
no need for it anymore so lets remove it.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
As the code paths that are guarded by CONFIG_XEN_DOM0 already depend
on CONFIG_ACPI so the extra #ifdef is not required. The earlier
patch that added them in had done its job.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
.. which means we can preset of NR_IRQS_LEGACY interrupts using
the 'acpi_get_override_irq' API before this loop.
This means that we can get the IRQ's polarity (and trigger) from either
the ACPI (or MP); or use the default values. This fixes a bug if we did
not have an IOAPIC we would not been able to preset the IRQ's polarity
if the MP table existed.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Since they are only called once and the rest of the pci_xen_*
functions follow the same pattern of setup.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
In the past we would guard those code segments to be dependent
on CONFIG_XEN_DOM0 (which depends on CONFIG_ACPI) so this patch is
not stricly necessary. But the next patch will merge common
HVM and initial domain code and we want to make sure the CONFIG_ACPI
dependency is preserved - as HVM code does not depend on CONFIG_XEN_DOM0.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Update the out-dated comment at the beginning of the file.
Also provide the copyrights of folks who have been contributing
to this code lately.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The file is hard to read. Move the code around so that
the contents of it follows a uniform format:
- setup GSIs - PV, HVM, and initial domain case
- then MSI/MSI-x setup - PV, HVM and then initial domain case.
- then MSI/MSI-x teardown - same order.
- lastly, the __init functions in PV, HVM, and initial domain order.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The code in setup_ioapic_irq() determines the Destination Field,
so why not also include it in the debug printk output that gets
displayed when the boot parameter "apic=debug" is used.
Before the change, "dmesg" will show:
IOAPIC[0]: Set routing entry (8-1 -> 0x31 -> IRQ 1 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (8-2 -> 0x30 -> IRQ 0 Mode:0 Active:0)
IOAPIC[0]: Set routing entry (8-3 -> 0x33 -> IRQ 3 Mode:0 Active:0) ...
After the change, you will see:
IOAPIC[0]: Set routing entry (8-1 -> 0x31 -> IRQ 1 Mode:0 Active:0 Dest:0)
IOAPIC[0]: Set routing entry (8-2 -> 0x30 -> IRQ 0 Mode:0 Active:0 Dest:0)
IOAPIC[0]: Set routing entry (8-3 -> 0x33 -> IRQ 3 Mode:0 Active:0 Dest:0) ...
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Link: http://lkml.kernel.org/r/20110708184603.2734.91071.sendpatchset@nchumbalkar.americas.cpqcorp.net
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When IOAPIC data is displayed in "dmesg" with the help of the
boot parameter "apic=debug" certain values are not formatted
correctly wrt their size.
In the "dmesg" snippet below, note that the output for "max
redirection entries", and "IO APIC version" which are each
defined to be just 8-bits long are displayed as 2 bytes in
length. Similarly, "Dst" under the "IRQ redirection table"
should only be 8-bits long.
IO APIC #0......
...
...
.... register #01: 00170020
....... : max redirection entries: 0017
....... : PRQ implemented: 0
....... : IO APIC version: 0020
...
...
.... IRQ redirection table:
NR Dst Mask Trig IRR Pol Stat Dmod Deli Vect:
00 000 1 0 0 0 0 0 0 00
01 000 0 0 0 0 0 0 0 31
02 000 0 0 0 0 0 0 0 30
03 000 1 0 0 0 0 0 0 33
...
...
Do some formatting clean up, so you will see output like below:
IO APIC #0......
...
...
.... register #01: 00170020
....... : max redirection entries: 17
....... : PRQ implemented: 0
....... : IO APIC version: 20
...
...
.... IRQ redirection table:
NR Dst Mask Trig IRR Pol Stat Dmod Deli Vect:
00 00 1 0 0 0 0 0 0 00
01 00 0 0 0 0 0 0 0 31
02 00 0 0 0 0 0 0 0 30
03 00 1 0 0 0 0 0 0 33
...
...
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Link: http://lkml.kernel.org/r/20110708184557.2734.61830.sendpatchset@nchumbalkar.americas.cpqcorp.net
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit 2706a0bf7b ("x86, NUMA: Enable CONFIG_AMD_NUMA on 32bit
too") enabled AMD NUMA for 32bit too. Unfortunately, SPARSEMEM
on 32bit had rather coarse (512MiB) addr->node mapping
granularity due to lack of space in page->flags. This led to
boot failure on certain AMD NUMA machines which had 128MiB
alignment on nodes.
Patches to properly detect this condition and reject NUMA
configuration are posted[1] but deemed too pervasive for merge
at this point (-rc6). Disable AMD NUMA for 32bit for now and
re-enable once the detection logic is merged.
[1] http://thread.gmane.org/gmane.linux.kernel/1161279/focus=1162583
Reported-by: Hans Rosenfeld <hans.rosenfeld@amd.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Conny Seidel <conny.seidel@amd.com>
Link: http://lkml.kernel.org/r/20110711083432.GC943@htj.dyndns.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Detect Xen before HyperV because in Viridian compatibility mode Xen
presents itself as HyperV. Move Xen to the top since it seems more
likely that Xen would emulate VMware than vice versa.
Signed-off-by: Anupam Chanda <achanda@nicira.com>
Link: http://lkml.kernel.org/r/1310150570-26810-1-git-send-email-achanda@nicira.com
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Yaozu (Eddie) Dong <eddie.dong@intel.com>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
nr_cpus allows one to specify number of possible cpus in the system.
Current assumption seems to be that first cpu to show up is boot cpu
and this assumption will be broken in kdump scenario where we can be
booting on a non boot cpu with nr_cpus=1.
It might happen that first cpu we parse is not the cpu we boot on and
later we ignore boot cpu. Though code later seems to recognize this
anomaly and forcibly sets boot cpu in physical cpu map with following
warning.
if (!physid_isset(hard_smp_processor_id(), phys_cpu_present_map)) {
printk(KERN_WARNING
"weird, boot CPU (#%d) not listed by the BIOS.\n",
hard_smp_processor_id());
physid_set(hard_smp_processor_id(), phys_cpu_present_map);
}
This patch waits for boot cpu to show up and starts ignoring the cpus
once we have hit (nr_cpus - 1) number of cpus. So effectively we are
reserving one slot out of nr_cpus for boot cpu explicitly.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/20110708171926.GF2930@redhat.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Don't use the EFI reboot method by default
x86, suspend: Restore MISC_ENABLE MSR in realmode wakeup
x86, reboot: Acer Aspire One A110 reboot quirk
x86-32, NUMA: Fix boot regression caused by NUMA init unification on highmem machines
I triggered a triple fault with gcc 4.5.1 because it did not
honor the inline annotation to arch_local_save_flags() function
and that function was added to the pool of functions traced by
the function tracer.
When preempt_schedule() called arch_local_save_flags() (called
by irqs_disabled()), it was traced, but the first thing the
function tracer does is disable preemption. When it enables
preemption, the NEED_RESCHED flag will not have been cleared and
the preemption check will trigger the call to preempt_schedule()
again.
Although the dynamic function tracer crashed immediately, the
static version of the function tracer (CONFIG_DYNAMIC_FTRACE is
not set) actually was able to show where the problem was.
swapper-1 3.N.. 103885us : arch_local_save_flags <-preempt_schedule
swapper-1 3.N.. 103886us : arch_local_save_flags <-preempt_schedule
swapper-1 3.N.. 103886us : arch_local_save_flags <-preempt_schedule
swapper-1 3.N.. 103887us : arch_local_save_flags <-preempt_schedule
swapper-1 3.N.. 103887us : arch_local_save_flags <-preempt_schedule
swapper-1 3.N.. 103888us : arch_local_save_flags <-preempt_schedule
swapper-1 3.N.. 103888us : arch_local_save_flags <-preempt_schedule
It went on for a while before it triple faulted with a corrupted
stack.
The arch_local_save_flags and arch_local_irq_* functions should
not be traced. Even though they are marked as inline, gcc may
still make them a function and enable tracing of them.
The simple solution is to just mark them as notrace. I had to
add the <linux/types.h> for this file to include the notrace
tag.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20110702033852.733414762@goodmis.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Previously we would check for acpi_sci_override_gsi == gsi every time
a PCI device was enabled. That works during early bootup, but later
on it could lead to triggering unnecessarily the acpi_gsi_to_irq(..) lookup.
The reason is that acpi_sci_override_gsi was declared in __initdata and
after early bootup could contain bogus values.
This patch moves the check for acpi_sci_override_gsi to the
site where the ACPI SCI is preset.
CC: stable@kernel.org
Reported-by: Raghavendra D Prabhu <rprabhu@wnohang.net>
Tested-by: Raghavendra D Prabhu <rprabhu@wnohang.net>
[http://lists.xensource.com/archives/html/xen-devel/2011-07/msg00154.html]
Suggested-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Testing suggests that at least some Lenovos and some Intels will
fail to reboot via EFI, attempting to jump to an unmapped
physical address. In the long run we could handle this by
providing a page table with a 1:1 mapping of physical addresses,
but for now it's probably just easier to assume that ACPI or
legacy methods will be present and reboot via those.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alan Cox <alan@linux.intel.com>
Link: http://lkml.kernel.org/r/1309985557-15350-1-git-send-email-mjg@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Some BIOSes will reset the Intel MISC_ENABLE MSR (specifically the
XD_DISABLE bit) when resuming from S3, which can interact poorly with
ebba638ae7. In 32bit PAE mode, this can
lead to a fault when EFER is restored by the kernel wakeup routines,
due to it setting the NX bit for a CPU that (thanks to the BIOS reset)
now incorrectly thinks it lacks the NX feature. (64bit is not affected
because it uses a common CPU bring-up that specifically handles the
XD_DISABLE bit.)
The need for MISC_ENABLE being restored so early is specific to the S3
resume path. Normally, MISC_ENABLE is saved in save_processor_state(),
but this happens after the resume header is created, so just reproduce
the logic here. (acpi_suspend_lowlevel() creates the header, calls
do_suspend_lowlevel, which calls save_processor_state(), so the saved
processor context isn't available during resume header creation.)
[ hpa: Consider for stable if OK in mainline ]
Signed-off-by: Kees Cook <kees.cook@canonical.com>
Link: http://lkml.kernel.org/r/20110707011034.GA8523@outflux.net
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: <stable@kernel.org> 2.6.38+
Add a driver for the ACPI-based EC event interface found on the
OLPC XO-1.5 laptop. This enables notification of battery/AC power events,
and enables various devices to be used as wakeup sources through regular
ACPI mechanisms.
This driver can't be built as a module, because some drivers need to know
at boot-time if SCI-based functionality is available via
olpc_ec_wakeup_available().
Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-12-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Add a driver to configure the XO-1 RTC via CS5536 MSRs, to be used as a
system wakeup source via olpc-xo1-pm.
Device detection is based on finding the relevant device tree node.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-11-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
EC events indicate change in AC power connectivity, battery state of
charge, battery error, battery presence, etc. Send notifications to
the power supply subsystem when changes are detected.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-10-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Configure the XO-1's lid switch GPIO to trigger an SCI interrupt,
and correctly expose this input device which can be used as a wakeup
source.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-9-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The EC in the OLPC XO-1 delivers GPE events to provide various
notifications. Add the basic code for GPE/EC event processing and
enable the ebook switch, which can be used as a wakeup source.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-8-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Update the EC SCI masks with recent additions.
Add functions to query SCI events and set the wakeup mask, to be used by
followup patches.
Add functions to tweak an event mask used to select certain EC events as
a system wakeup source. Also add a function to determine if EC wakeup
functionality is available, as this depends on child drivers (different
for each laptop model) to configure the SCI interrupt.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-7-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The System Control Interrupt is used in the OLPC XO-1 to control various
features of the laptop. Add the driver base and the power button
functionality.
This driver can't be built as a module, because functionality added in
future patches means that some drivers need to know at boot-time whether
SCI-based functionality is available.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-6-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Add code needed for basic suspend/resume of the XO-1 laptop.
Based on earlier work by Jordan Crouse, Andres Salomon, and others.
This patch incorporates all earlier feedback from Thomas Gleixner. To
clarify a certain point (now more obvious in the code itself):
On resume, OpenFirmware returns execution to Linux in protected mode
with a kernel-compatible GDT already set up. The changes and
simplifications suggested have all been included.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-5-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Based on earlier review comments, we'll no longer try to stick all of
our XO-1 goodies in a single driver. We'll split it into a power management
driver, and an EC/SCI driver.
As a first step, rename olpc-xo1 to olpc-xo1-pm, and make it builtin
instead of modular.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-4-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Move these definitions into the relevant header file.
This was requested in the review of the upcoming XO-1 suspend/resume code.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-3-git-send-email-dsd@laptop.org
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
In response to new device tree code in the kernel, OLPC will start
using it for probing of certain devices. However, some firmware fixes
are needed to put the devicetree into a usable state.
Retain compatibility with old firmware by fixing up the device tree
at boot-time if it does not contain the new nodes/properties that
we need for probing. This is the same approach taken on PPC platforms.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Link: http://lkml.kernel.org/r/1309019658-1712-2-git-send-email-dsd@laptop.org
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Andres Salomon <dilinger@queued.net>
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Since git commit
660e34cebf x86: reorder reboot method
preferences,
my Acer Aspire One hangs on reboot. It appears that its ACPI method
for rebooting is broken. The attached patch adds a quirk so that the
machine will reboot via the BIOS.
[ hpa: verified that the ACPI control on this machine is just plain broken. ]
Signed-off-by: Peter Chubb <peter.chubb@nicta.com.au>
Link: http://lkml.kernel.org/r/w439iki5vl.wl%25peter@chubb.wattle.id.au
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Consumers of the table pointers in struct efi check for
EFI_INVALID_TABLE_ADDR to determine validity, hence these
pointers should all be pre-initialized to this value (rather
than zero).
Noticed by the discrepancy between efivars' systab sysfs entry
showing all tables (and their pointers) despite the code
intending to only display the valid ones. No other bad effects
known, but having the various table parsing routines bogusly
access physical address zero is certainly not very desirable
(even though they're unlikely to find anything useful there).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Link: http://lkml.kernel.org/r/4E13100A020000780004C256@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
rbp is used in SAVE_ARGS_IRQ to save the old stack pointer
in order to restore it later in ret_from_intr.
It is convenient because we save its value in the irq regs
and it's easily restored using the leave instruction.
However this is a kind of abuse of the frame pointer which
role is to help unwinding the kernel by chaining frames
together, each node following the return address to the
previous frame.
But although we are breaking the frame by changing the stack
pointer, there is no preceding return address before the new
frame. Hence using the frame pointer to link the two stacks
breaks the stack unwinders that find a random value instead of
a return address here.
There is no workaround that can work in every case. We are using
the fixup_bp_irq_link() function to dereference that abused frame
pointer in the case of non nesting interrupt (which means stack
changed).
But that doesn't fix the case of interrupts that don't change the
stack (but we still have the unconditional frame link), which is
the case of hardirq interrupting softirq. We have no way to detect
this transition so the frame irq link is considered as a real frame
pointer and the return address is dereferenced but it is still a
spurious one.
There are two possible results of this: either the spurious return
address, a random stack value, luckily belongs to the kernel text
and then the unwinding can continue and we just have a weird entry
in the stack trace. Or it doesn't belong to the kernel text and
unwinding stops there.
This is the reason why stacktraces (including perf callchains) on
irqs that interrupted softirqs don't work very well.
To solve this, we don't save the old stack pointer on rbp anymore
but we save it to a scratch register that we push on the new
stack and that we pop back later on irq return.
This preserves the whole frame chain without spurious return addresses
in the middle and drops the need for the horrid fixup_bp_irq_link()
workaround.
And finally irqs that interrupt softirq are sanely unwinded.
Before:
99.81% perf [kernel.kallsyms] [k] perf_pending_event
|
--- perf_pending_event
irq_work_run
smp_irq_work_interrupt
irq_work_interrupt
|
|--41.60%-- __read
| |
| |--99.90%-- create_worker
| | bench_sched_messaging
| | cmd_bench
| | run_builtin
| | main
| | __libc_start_main
| --0.10%-- [...]
After:
1.64% swapper [kernel.kallsyms] [k] perf_pending_event
|
--- perf_pending_event
irq_work_run
smp_irq_work_interrupt
irq_work_interrupt
|
|--95.00%-- arch_irq_work_raise
| irq_work_queue
| __perf_event_overflow
| perf_swevent_overflow
| perf_swevent_event
| perf_tp_event
| perf_trace_softirq
| __do_softirq
| call_softirq
| do_softirq
| irq_exit
| |
| |--73.68%-- smp_apic_timer_interrupt
| | apic_timer_interrupt
| | |
| | |--96.43%-- amd_e400_idle
| | | cpu_idle
| | | start_secondary
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jan Beulich <JBeulich@novell.com>
The unwinder backlink in interrupt entry is very useless.
It's actually not part of the stack frame chain and thus is
never used.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jan Beulich <JBeulich@novell.com>
Just for clarity in the code. Have a first block that handles
the frame pointer and a separate one that handles pt_regs
pointer and its use.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jan Beulich <JBeulich@novell.com>
The save_regs function that saves the regs on low level
irq entry is complicated because of the fact it changes
its stack in the middle and also because it manipulates
data allocated in the caller frame and accesses there
are directly calculated from callee rsp value with the
return address in the middle of the way.
This complicates the static stack offsets calculation and
require more dynamic ones. It also needs a save/restore
of the function's return address.
To simplify and optimize this, turn save_regs() into a
macro.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jan Beulich <JBeulich@novell.com>
When regs are passed to dump_stack(), we fetch the frame
pointer from the regs but the stack pointer is taken from
the current frame.
Thus the frame and stack pointers may not come from the same
context. For example this can result in the unwinder to
think the context is in irq, due to the current value of
the stack, but the frame pointer coming from the regs points
to a frame from another place. It then tries to fix up
the irq link but ends up dereferencing a random frame
pointer that doesn't belong to the irq stack:
[ 9131.706906] ------------[ cut here ]------------
[ 9131.707003] WARNING: at arch/x86/kernel/dumpstack_64.c:129 dump_trace+0x2aa/0x330()
[ 9131.707003] Hardware name: AMD690VM-FMH
[ 9131.707003] Perf: bad frame pointer = 0000000000000005 in callchain
[ 9131.707003] Modules linked in:
[ 9131.707003] Pid: 1050, comm: perf Not tainted 3.0.0-rc3+ #181
[ 9131.707003] Call Trace:
[ 9131.707003] <IRQ> [<ffffffff8104bd4a>] warn_slowpath_common+0x7a/0xb0
[ 9131.707003] [<ffffffff8104be21>] warn_slowpath_fmt+0x41/0x50
[ 9131.707003] [<ffffffff8178b873>] ? bad_to_user+0x6d/0x10be
[ 9131.707003] [<ffffffff8100c2da>] dump_trace+0x2aa/0x330
[ 9131.707003] [<ffffffff810107d3>] ? native_sched_clock+0x13/0x50
[ 9131.707003] [<ffffffff8101b164>] perf_callchain_kernel+0x54/0x70
[ 9131.707003] [<ffffffff810d391f>] perf_prepare_sample+0x19f/0x2a0
[ 9131.707003] [<ffffffff810d546c>] __perf_event_overflow+0x16c/0x290
[ 9131.707003] [<ffffffff810d5430>] ? __perf_event_overflow+0x130/0x290
[ 9131.707003] [<ffffffff810107d3>] ? native_sched_clock+0x13/0x50
[ 9131.707003] [<ffffffff8100fbb9>] ? sched_clock+0x9/0x10
[ 9131.707003] [<ffffffff810752e5>] ? T.375+0x15/0x90
[ 9131.707003] [<ffffffff81084da4>] ? trace_hardirqs_on_caller+0x64/0x180
[ 9131.707003] [<ffffffff810817bd>] ? trace_hardirqs_off+0xd/0x10
[ 9131.707003] [<ffffffff810d5764>] perf_event_overflow+0x14/0x20
[ 9131.707003] [<ffffffff810d588c>] perf_swevent_hrtimer+0x11c/0x130
[ 9131.707003] [<ffffffff817821a1>] ? error_exit+0x51/0xb0
[ 9131.707003] [<ffffffff81072e93>] __run_hrtimer+0x83/0x1e0
[ 9131.707003] [<ffffffff810d5770>] ? perf_event_overflow+0x20/0x20
[ 9131.707003] [<ffffffff81073256>] hrtimer_interrupt+0x106/0x250
[ 9131.707003] [<ffffffff812a3bfd>] ? trace_hardirqs_off_thunk+0x3a/0x3c
[ 9131.707003] [<ffffffff81024833>] smp_apic_timer_interrupt+0x53/0x90
[ 9131.707003] [<ffffffff81789053>] apic_timer_interrupt+0x13/0x20
[ 9131.707003] <EOI> [<ffffffff817821a1>] ? error_exit+0x51/0xb0
[ 9131.707003] [<ffffffff8178219c>] ? error_exit+0x4c/0xb0
[ 9131.707003] ---[ end trace b2560d4876709347 ]---
Fix this by simply taking the stack pointer from regs->sp
when regs are provided.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
In order to prepare for fetching the stack pointer from the
regs when possible in dump_trace() instead of taking the
local one, save the current stack pointer in perf live regs saving.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
This code uses PCI_CLASS_REVISION instead of PCI_REVISION_ID, so
it wasn't converted by commit 44c10138fd ("PCI: Change all
drivers to use pci_device->revision") before being moved to
arch/x86/...
Do it now at last -- and save one level of indentation...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/201107012242.08347.sshtylyov@ru.mvista.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'stable/bug.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pci: Use the INT_SRC_OVR IRQ (instead of GSI) to preset the ACPI SCI IRQ.
xen/mmu: Fix for linker errors when CONFIG_SMP is not defined.
During 32/64 NUMA init unification, commit 797390d855 ("x86-32,
NUMA: use sparse_memory_present_with_active_regions()") made
32bit mm init call memory_present() automatically from
active_regions instead of leaving it to each NUMA init path.
This commit description is inaccurate - memory_present() calls
aren't the same for flat and numaq. After the commit,
memory_present() is only called for the intersection of e820 and
NUMA layout. Before, on flatmem, memory_present() would be
called from 0 to max_pfn. After, it would be called only on the
areas that e820 indicates to be populated.
This is how x86_64 works and should be okay as memmap is allowed
to contain holes; however, x86_32 DISCONTIGMEM is missing
early_pfn_valid(), which makes memmap_init_zone() assume that
memmap doesn't contain any hole. This leads to the following
oops if e820 map contains holes as it often does on machine with
near or more 4GiB of memory by calling pfn_to_page() on a pfn
which isn't mapped to a NUMA node, a reported by Conny Seidel:
BUG: unable to handle kernel paging request at 000012b0
IP: [<c1aa13ce>] memmap_init_zone+0x6c/0xf2
*pdpt =3D 0000000000000000 *pde =3D f000eef3f000ee00
Oops: 0000 [#1] SMP
last sysfs file:
Modules linked in:
Pid: 0, comm: swapper Not tainted 2.6.39-rc5-00164-g797390d #1 To Be Filled By O.E.M. To Be Filled By O.E.M./E350M1
EIP: 0060:[<c1aa13ce>] EFLAGS: 00010012 CPU: 0
EIP is at memmap_init_zone+0x6c/0xf2
EAX: 00000000 EBX: 000a8000 ECX: 000a7fff EDX: f2c00b80
ESI: 000a8000 EDI: f2c00800 EBP: c19ffe54 ESP: c19ffe34
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
Process swapper (pid: 0, ti=3Dc19fe000 task=3Dc1a07f60 task.ti=3Dc19fe000)
Stack:
00000002 00000000 0023f000 00000000 10000000 00000a00 f2c00000 f2c00b58
c19ffeb0 c1a80f24 000375fe 00000000 f2c00800 00000800 00000100 00000030
c1abb768 0000003c 00000000 00000000 00000004 00207a02 f2c00800 000375fe
Call Trace:
[<c1a80f24>] free_area_init_node+0x358/0x385
[<c1a81384>] free_area_init_nodes+0x420/0x487
[<c1a79326>] paging_init+0x114/0x11b
[<c1a6cb13>] setup_arch+0xb37/0xc0a
[<c1a69554>] start_kernel+0x76/0x316
[<c1a690a8>] i386_start_kernel+0xa8/0xb0
This patch fixes the bug by defining early_pfn_valid() to be the
same as pfn_valid() when DISCONTIGMEM.
Reported-bisected-and-tested-by: Conny Seidel <conny.seidel@amd.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: hans.rosenfeld@amd.com
Cc: Christoph Lameter <cl@linux.com>
Cc: Conny Seidel <conny.seidel@amd.com>
Link: http://lkml.kernel.org/r/20110628094107.GB3386@htj.dyndns.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The v1 PMU does not have any fixed counters. Using the v2 constraints,
which do have fixed counters, causes an additional choice to be present
in the weight calculation, but not when actually scheduling the event,
leading to an event being not scheduled at all.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1309362157-6596-3-git-send-email-avi@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The perf_event overflow handler does not receive any caller-derived
argument, so many callers need to resort to looking up the perf_event
in their local data structure. This is ugly and doesn't scale if a
single callback services many perf_events.
Fix by adding a context parameter to perf_event_create_kernel_counter()
(and derived hardware breakpoints APIs) and storing it in the perf_event.
The field can be accessed from the callback as event->overflow_handler_context.
All callers are updated.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1309362157-6596-2-git-send-email-avi@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add a NODE level to the generic cache events which is used to measure
local vs remote memory accesses. Like all other cache events, an
ACCESS is HIT+MISS, if there is no way to distinguish between reads
and writes do reads only etc..
The below needs filling out for !x86 (which I filled out with
unsupported events).
I'm fairly sure ARM can leave it like that since it doesn't strike me as
an architecture that even has NUMA support. SH might have something since
it does appear to have some NUMA bits.
Sparc64, PowerPC and MIPS certainly want a good look there since they
clearly are NUMA capable.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: David Miller <davem@davemloft.net>
Cc: Anton Blanchard <anton@samba.org>
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/1303508226.4865.8.camel@laptop
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Since the OFFCORE registers are fully symmetric, try the other one
when the specified one is already in use.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1306141897.18455.8.camel@twins
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds Intel Sandy Bridge offcore_response support by
providing the low-level constraint table for those events.
On Sandy Bridge, there are two offcore_response events. Each uses
its own dedictated extra register. But those registers are NOT shared
between sibling CPUs when HT is on unlike Nehalem/Westmere. They are
always private to each CPU. But they still need to be controlled within
an event group. All events within an event group must use the same
value for the extra MSR. That's not controlled by the second patch in
this series.
Furthermore on Sandy Bridge, the offcore_response events have NO
counter constraints contrary to what the official documentation
indicates, so drop the events from the contraint table.
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20110606145712.GA7304@quad
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The validate_group() function needs to validate events with
extra shared regs. Within an event group, only events with
the same value for the extra reg can co-exist. This was not
checked by validate_group() because it was missing the
shared_regs logic.
This patch changes the allocation of the fake cpuc used for
validation to also point to a fake shared_regs structure such
that group events be properly testing.
It modifies __intel_shared_reg_get_constraints() to use
spin_lock_irqsave() to avoid lockdep issues.
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20110606145708.GA7279@quad
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch improves the code managing the extra shared registers
used for offcore_response events on Intel Nehalem/Westmere. The
idea is to use static allocation instead of dynamic allocation.
This simplifies greatly the get and put constraint routines for
those events.
The patch also renames per_core to shared_regs because the same
data structure gets used whether or not HT is on. When HT is
off, those events still need to coordination because they use
a extra MSR that has to be shared within an event group.
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20110606145703.GA7258@quad
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Since only samples call perf_output_sample() its much saner (and more
correct) to put the sample logic in there than in the
perf_output_begin()/perf_output_end() pair.
Saves a useless argument, reduces conditionals and shrinks
struct perf_output_handle, win!
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-2crpvsx3cqu67q3zqjbnlpsc@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The nmi parameter indicated if we could do wakeups from the current
context, if not, we would set some state and self-IPI and let the
resulting interrupt do the wakeup.
For the various event classes:
- hardware: nmi=0; PMI is in fact an NMI or we run irq_work_run from
the PMI-tail (ARM etc.)
- tracepoint: nmi=0; since tracepoint could be from NMI context.
- software: nmi=[0,1]; some, like the schedule thing cannot
perform wakeups, and hence need 0.
As one can see, there is very little nmi=1 usage, and the down-side of
not using it is that on some platforms some software events can have a
jiffy delay in wakeup (when arch_irq_work_raise isn't implemented).
The up-side however is that we can remove the nmi parameter and save a
bunch of conditionals in fast paths.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Michael Cree <mcree@orcon.net.nz>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Eric B Munson <emunson@mgebm.net>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Don Zickus <dzickus@redhat.com>
Link: http://lkml.kernel.org/n/tip-agjev8eu666tvknpb3iaj0fg@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Due to restriction and specifics of Netburst PMU we need a separated
event for NMI watchdog. In particular every Netburst event
consumes not just a counter and a config register, but also an
additional ESCR register.
Since ESCR registers are grouped upon counters (i.e. if ESCR is occupied
for some event there is no room for another event to enter until its
released) we need to pick up the "least" used ESCR (or the most available
one) for nmi-watchdog purposes -- so MSR_P4_CRU_ESCR2/3 was chosen.
With this patch nmi-watchdog and perf top should be able to run simultaneously.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
CC: Lin Ming <ming.m.lin@intel.com>
CC: Arnaldo Carvalho de Melo <acme@redhat.com>
CC: Frederic Weisbecker <fweisbec@gmail.com>
Tested-and-reviewed-by: Don Zickus <dzickus@redhat.com>
Tested-and-reviewed-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20110623124918.GC13050@sun
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove the hysterical outb/inb_pit defines and use outb_p/inb_p in the
code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: John Stultz <john.stultz@linaro.org>
Link: http://lkml.kernel.org/r/20110609130622.348437125@linutronix.de
Before check_fpu() is called, we have cr0.TS bit set and hence the floating
point code to check the FDIV bug was generating a DNA exception.
Use kernel_fpu_begin()/kernel_fpu_end() around the floating point
code to avoid this unnecessary device not available exception during
boot.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1309479572.2665.1372.camel@sbsiddha-MOBL3.sc.intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
In the past we would use the GSI value to preset the ACPI SCI
IRQ which worked great as GSI == IRQ:
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
While that is most often seen, there are some oddities:
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 20 low level)
which means that GSI 20 (or pin 20) is to be overriden for IRQ 9.
Our code that presets the interrupt for ACPI SCI however would
use the GSI 20 instead of IRQ 9 ending up with:
xen: sci override: global_irq=20 trigger=0 polarity=1
xen: registering gsi 20 triggering 0 polarity 1
xen: --> pirq=20 -> irq=20
xen: acpi sci 20
.. snip..
calling acpi_init+0x0/0xbc @ 1
ACPI: SCI (IRQ9) allocation failed
ACPI Exception: AE_NOT_ACQUIRED, Unable to install System Control Interrupt handler (20110413/evevent-119)
ACPI: Unable to start the ACPI Interpreter
as the ACPI interpreter made a call to 'acpi_gsi_to_irq' which got nine.
It used that value to request an IRQ (request_irq) and since that was not
present it failed.
The fix is to recognize that for interrupts that are overriden (in our
case we only care about the ACPI SCI) we should use the IRQ number
to present the IRQ instead of the using GSI. End result is that we get:
xen: sci override: global_irq=20 trigger=0 polarity=1
xen: registering gsi 20 triggering 0 polarity 1
xen: --> pirq=20 -> irq=9 (gsi=9)
xen: acpi sci 9
which fixes the ACPI interpreter failing on startup.
CC: stable@kernel.org
Reported-by: Liwei <xieliwei@gmail.com>
Tested-by: Liwei <xieliwei@gmail.com>
[http://lists.xensource.com/archives/html/xen-devel/2011-06/msg01727.html]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Simple enough - we use an extern defined symbol which is not
defined when CONFIG_SMP is not defined. This fixes the linker
dying.
CC: stable@kernel.org
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
%rip-relative addressing is relative to the first byte of the next instruction,
so we need to add %rip only after we've fetched any immediate bytes.
Based on original patch by Li Xin <xin.li@intel.com>.
Signed-off-by: Avi Kivity <avi@redhat.com>
Acked-by: Li Xin <xin.li@intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Trying to build the Intel SCU Watchdog fails for me with gcc 4.6.0 -
$ gcc --version | head -n 1
gcc (GCC) 4.6.0 20110513 (prerelease)
like this :
CC drivers/watchdog/intel_scu_watchdog.o
In file included from drivers/watchdog/intel_scu_watchdog.c:49:0:
/home/jj/src/linux-2.6/arch/x86/include/asm/apb_timer.h: In function ‘apbt_time_init’:
/home/jj/src/linux-2.6/arch/x86/include/asm/apb_timer.h:65:42: warning: ‘return’ with a value, in function returning void [enabled by default]
drivers/watchdog/intel_scu_watchdog.c: In function ‘intel_scu_watchdog_init’:
drivers/watchdog/intel_scu_watchdog.c:468:2: error: implicit declaration of function ‘sfi_get_mtmr’ [-Werror=implicit-function-declaration]
drivers/watchdog/intel_scu_watchdog.c:468:32: warning: assignment makes pointer from integer without a cast [enabled by default]
cc1: some warnings being treated as errors
make[1]: *** [drivers/watchdog/intel_scu_watchdog.o] Error 1
make: *** [drivers/watchdog/intel_scu_watchdog.o] Error 2
Additionally, linux/types.h is needlessly being included twice in
drivers/watchdog/intel_scu_watchdog.c
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
MTRR rendezvous sequence is not implemened using stop_machine() before, as this
gets called both from the process context aswell as the cpu online paths
(where the cpu has not come online and the interrupts are disabled etc).
Now that we have a new stop_machine_from_inactive_cpu() API, use it for
rendezvous during mtrr init of a logical processor that is coming online.
For the rest (runtime MTRR modification, system boot, resume paths), use
stop_machine() to implement the rendezvous sequence. This will consolidate and
cleanup the code.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/20110623182057.076997177@sbsiddha-MOBL3.sc.intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The APB timers are an IP block from Synopsys (DesignWare APB timers)
and are also found in other systems including ARM SoC's. This patch
adds functions for creating clock_event_devices and clocksources from
APB timers but does not do the resource allocation. This is handled
in a higher layer to allow the timers to be created from multiple
methods such as platform_devices.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
commit 21a3c96 uses node_start/end_pfn(nid) for detection start/end
of nodes. But, it's not defined in linux/mmzone.h but defined in
/arch/???/include/mmzone.h which is included only under
CONFIG_NEED_MULTIPLE_NODES=y.
Then, we see
mm/page_cgroup.c: In function 'page_cgroup_init':
mm/page_cgroup.c:308: error: implicit declaration of function 'node_start_pfn'
mm/page_cgroup.c:309: error: implicit declaration of function 'node_end_pfn'
So, fixiing page_cgroup.c is an idea...
But node_start_pfn()/node_end_pfn() is a very generic macro and
should be implemented in the same manner for all archs.
(m32r has different implementation...)
This patch removes definitions of node_start/end_pfn() in each archs
and defines a unified one in linux/mmzone.h. It's not under
CONFIG_NEED_MULTIPLE_NODES, now.
A result of macro expansion is here (mm/page_cgroup.c)
for !NUMA
start_pfn = ((&contig_page_data)->node_start_pfn);
end_pfn = ({ pg_data_t *__pgdat = (&contig_page_data); __pgdat->node_start_pfn + __pgdat->node_spanned_pages;});
for NUMA (x86-64)
start_pfn = ((node_data[nid])->node_start_pfn);
end_pfn = ({ pg_data_t *__pgdat = (node_data[nid]); __pgdat->node_start_pfn + __pgdat->node_spanned_pages;});
Changelog:
- fixed to avoid using "nid" twice in node_end_pfn() macro.
Reported-and-acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Reported-and-tested-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
MTRR rendezvous sequence using stop_one_cpu_nowait() can potentially
happen in parallel with another system wide rendezvous using
stop_machine(). This can lead to deadlock (The order in which
works are queued can be different on different cpu's. Some cpu's
will be running the first rendezvous handler and others will be running
the second rendezvous handler. Each set waiting for the other set to join
for the system wide rendezvous, leading to a deadlock).
MTRR rendezvous sequence is not implemented using stop_machine() as this
gets called both from the process context aswell as the cpu online paths
(where the cpu has not come online and the interrupts are disabled etc).
stop_machine() works with only online cpus.
For now, take the stop_machine mutex in the MTRR rendezvous sequence that
gets called from an online cpu (here we are in the process context
and can potentially sleep while taking the mutex). And the MTRR rendezvous
that gets triggered during cpu online doesn't need to take this stop_machine
lock (as the stop_machine() already ensures that there is no cpu hotplug
going on in parallel by doing get_online_cpus())
TBD: Pursue a cleaner solution of extending the stop_machine()
infrastructure to handle the case where the calling cpu is
still not online and use this for MTRR rendezvous sequence.
fixes: https://bugzilla.novell.com/show_bug.cgi?id=672008
Reported-by: Vadim Kotelnikov <vadimuzzz@inbox.ru>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/20110623182056.807230326@sbsiddha-MOBL3.sc.intel.com
Cc: stable@kernel.org # 2.6.35+, backport a week or two after this gets more testing in mainline
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
A simple implementation that only supports the word size and does not
have a fallback mode (would require a spinlock).
Add 32 and 64 bit support for cmpxchg_double. cmpxchg double uses
the cmpxchg8b or cmpxchg16b instruction on x86 processors to compare
and swap 2 machine words. This allows lockless algorithms to move more
context information through critical sections.
Set a flag CONFIG_CMPXCHG_DOUBLE to signal that support for double word
cmpxchg detection has been build into the kernel. Note that each subsystem
using cmpxchg_double has to implement a fall back mechanism as long as
we offer support for processors that do not implement cmpxchg_double.
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Christoph Lameter <cl@linux.com>
Link: http://lkml.kernel.org/r/20110601172614.173427964@linux.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
x86/PCI/ACPI: fix type mismatch
PCI: fix new kernel-doc warning
PCI: Fix warning in drivers/pci/probe.c on sparc64
Remove linux/mm.h inclusion from netdevice.h -- it's unused (I've checked manually).
To prevent mm.h inclusion via other channels also extract "enum dma_data_direction"
definition into separate header. This tiny piece is what gluing netdevice.h with mm.h
via "netdevice.h => dmaengine.h => dma-mapping.h => scatterlist.h => mm.h".
Removal of mm.h from scatterlist.h was tried and was found not feasible
on most archs, so the link was cutoff earlier.
Hope people are OK with tiny include file.
Note, that mm_types.h is still dragged in, but it is a separate story.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct the UV2 broacast assist unit's destination timeout
period. And the activation status register in UV2 should be
tested for a destination timeout with a 4, not a 2. The values
for Active versus Timeout were reversed.
This patch is critical for TLB shootdown on an Altix UV2 system
(i.e. the follow-on to the current Altix UV).
Destination timeout period:
The period is set in 4 bits of memory-mapped register MISC_CONTROL.
The left bit toggles base period between 10us and 80us.
The other 3 bits are the multiplier.
Decimal 15, hex f, gives the maximum: 7 * 80us
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Link: http://lkml.kernel.org/r/20110621122243.117324443@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix a memory leak in init_per_cpu() when the topology check
fails.
The leak should never occur on deployed systems. It would only occur
in an unexpected topology that would make the BAU unuseable as a result.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Link: http://lkml.kernel.org/r/20110621122242.981533045@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove the large stack-resident cpumask_t from
reset_with_ipi()'s stack by allocating one per uvhub.
Due to the limited size of the stack the potentially huge cpumask_t may
cause stack overrun. We haven't seen it happen yet, but we need to make it
a practice not to push such structures onto the stack.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Link: http://lkml.kernel.org/r/20110621122242.832589130@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Rename 'bau_targ_hubmask' to 'pnmask' for clarity.
The BAU distribution bit mask is indexed by pnode number, not hub or
blade number. This important fact is not clear while the mask is
called a 'hubmask'.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Link: http://lkml.kernel.org/r/20110621122242.630995969@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix reset_with_ipi() to look up a cpu for a blade based on the
distribution map being indexed by the potentially sparsely
numbered pnode.
This patch is critical to tlb shootdown on a partitioned UV
system, or one with nonconsecutive blade numbers.
The distribution map bits represent pnodes relative to the partition base
pnode. Previous to this patch it had been assuming bits based on 0-based,
consecutive blade ids.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Link: http://lkml.kernel.org/r/20110621122242.497700003@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix for the topology in which there is a socket 1 on a blade
with no socket 0.
Only call make_per_cpu_thp() for present sockets.
We have only seen this fail for internal configurations.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Link: http://lkml.kernel.org/r/20110621122242.363757364@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Make all the functions in uv_bau.h inline so that it can
be included in the fake prom (used in simulations).
If not inlined the unused functions will generate compiler warnings.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Link: http://lkml.kernel.org/r/20110621122242.230529678@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix a call by tunables_write() to smp_processor_id() within a
preemptable region.
Call get_cpu()/put_cpu() around the region where the returned
cpu number is actually used, which makes it non-preemptable.
A DEBUG_PREEMPT warning is prevented.
UV does not support cpu hotplug yet, but this is a step toward
that ability as well.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Link: http://lkml.kernel.org/r/20110621122242.086384966@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
A few parts of the driver were missing in drivers/iommu.
Move them there to have the complete driver in that
directory.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This should ease finding similarities with different platforms,
with the intention of solving problems once in a generic framework
which everyone can use.
Note: to move intel-iommu.c, the declaration of pci_find_upstream_pcie_bridge()
has to move from drivers/pci/pci.h to include/linux/pci.h. This is handled
in this patch, too.
As suggested, also drop DMAR's EXPERIMENTAL tag while we're at it.
Compile-tested on x86_64.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This should ease finding similarities with different platforms,
with the intention of solving problems once in a generic framework
which everyone can use.
Compile-tested on x86_64.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
* 'stable/bug.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/setup: Fix for incorrect xen_extra_mem_start.
xen: When calling power_off, don't call the halt function.
xen: Fix compile warning when CONFIG_SMP is not defined.
xen: support CONFIG_MAXSMP
xen: partially revert "xen: set max_pfn_mapped to the last pfn mapped"
* 'kvm-updates/3.0' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: Fix register corruption in pvclock_scale_delta
KVM: MMU: fix opposite condition in mapping_level_dirty_bitmap
KVM: VMX: do not overwrite uptodate vcpu->arch.cr3 on KVM_SET_SREGS
KVM: MMU: Fix build warnings in walk_addr_generic()
Many stupid corrections of duplicated includes based on the output of
scripts/checkincludes.pl.
Signed-off-by: Vitaliy Ivanov <vitalivanov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The 128-bit multiply in pvclock.h was missing an output constraint for
EDX which caused a register corruption to appear. Thanks to Ulrich for
diagnosing the EDX corruption and Avi for providing this fix.
Signed-off-by: Zachary Amsden <zamsden@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The condition is opposite, it always maps huge page for the dirty tracked page
Reported-by: Steve <stefan.bosak@gmail.com>
Signed-off-by: Steve <stefan.bosak@gmail.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Only decache guest CR3 value if vcpu->arch.cr3 is stale.
Fixes loadvm with live guest.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Tested-by: Markus Schade <markus.schade@gmail.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
On 3.0-rc1 I get
In file included from arch/x86/kvm/mmu.c:2856:
arch/x86/kvm/paging_tmpl.h: In function ‘paging32_walk_addr_generic’:
arch/x86/kvm/paging_tmpl.h:124: warning: ‘ptep_user’ may be used uninitialized in this function
In file included from arch/x86/kvm/mmu.c:2852:
arch/x86/kvm/paging_tmpl.h: In function ‘paging64_walk_addr_generic’:
arch/x86/kvm/paging_tmpl.h:124: warning: ‘ptep_user’ may be used uninitialized in this function
caused by 6e2ca7d180. According to Takuya
Yoshikawa, ptep_user won't be used uninitialized so shut up gcc.
Cc: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Link: http://lkml.kernel.org/r/20110530094604.GC21833@liondog.tnic
Signed-off-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Commit 916f676f8d started reserving boot service code since some systems
require you to keep that code around until SetVirtualAddressMap is called.
However, in some cases those areas will overlap with reserved regions.
The proper medium-term fix is to fix the bootloader to prevent the
conflicts from occurring by moving the kernel to a better position,
but the kernel should check for this possibility, and only reserve regions
which can be reserved.
Signed-off-by: Maarten Lankhorst <m.b.lankhorst@gmail.com>
Link: http://lkml.kernel.org/r/4DF7A005.1050407@gmail.com
Acked-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The earlier attempts (24bdb0b62c)
at fixing this problem caused other problems to surface (PV guests
with no PCI passthrough would have SWIOTLB turned on - which meant
64MB of precious contingous DMA32 memory being eaten up per guest).
The problem was: "on xen we add an extra memory region at the end of
the e820, and on this particular machine this extra memory region
would start below 4g and cross over the 4g boundary:
[0xfee01000-0x192655000)
Unfortunately e820_end_of_low_ram_pfn does not expect an
e820 layout like that so it returns 4g, therefore initial_memory_mapping
will map [0 - 0x100000000), that is a memory range that includes some
reserved memory regions."
The memory range was the IOAPIC regions, and with the 1-1 mapping
turned on, it would map them as RAM, not as MMIO regions. This caused
the hypervisor to complain. Fortunately this is experienced only under
the initial domain so we guard for it.
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The ucode size check has to take the section header size into account
too when sanity checking the section length. Shorten and clarify define
names, while at it.
Caught-by: Ben Hutchings <ben@decadent.org.uk>
Link: http://lkml.kernel.org/r/1302752223.5282.674.camel@localhost
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
There are many functions named mce_* so use a new prefix for the subset
of functions related to sysfs support.
And since f3c6ea1b06 introduces
syscore_ops, use the prefix mce_syscore for some functions related to
power management which were in sysdev_class before.
Before: After:
mce_device mce_sysdev
mce_sysclass mce_sysdev_class
mce_attrs mce_sysdev_attrs
mce_dev_initialized mce_sysdev_initialized
mce_create_device mce_sysdev_create
mce_remove_device mce_sysdev_remove
mce_suspend mce_syscore_suspend
mce_shutdown mce_syscore_shutdown
mce_resume mce_syscore_resume
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/4DEED81B.8020506@jp.fujitsu.com
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
There are many functions named mce_* so use a new prefix for the subset
of functions dealing with the character device /dev/mcelog.
This change doesn't impact the mce-inject module because the exported
symbol mce_chrdev_ops already has the prefix, therefore it is left
unchanged.
Before: After:
mce_wait mce_chrdev_wait
mce_state_lock mce_chrdev_state_lock
open_count mce_chrdev_open_count
open_exclu mce_chrdev_open_exclu
mce_open mce_chrdev_open
mce_release mce_chrdev_release
mce_read_mutex mce_chrdev_read_mutex
mce_read mce_chrdev_read
mce_poll mce_chrdev_poll
mce_ioctl mce_chrdev_ioctl
mce_log_device mce_chrdev_device
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/4DEED7CD.3040500@jp.fujitsu.com
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Use a temporary local variable m to simplify the code. No change in
logic.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/4DEED7A8.8020307@jp.fujitsu.com
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Use temporary local variable sysdev to simplify the code. No change in
logic.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/4DEED777.7080205@jp.fujitsu.com
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Because "ancient CPUs" like p5 and winchip don't have X86_FEATURE_MCA
(I suppose so), mcheck_cpu_init() on such CPUs will return at check of
mce_available() after __mcheck_cpu_ancient_init().
It is hard to know this implicit behavior without knowing the CPUs
well. So make it clear that we leave mcheck_cpu_init() when the CPU is
initialized in __mcheck_cpu_ancient_init().
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/4DEED74B.20502@jp.fujitsu.com
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
This patch introduces mce_gather_info() which is to be called at the
beginning of error handling and gathers minimum error information from
proper error registers (and saved registers).
As the result of mce_get_rip() is integrated, unnecessary zeroing
is removed. This also takes care of saving RIP which is required to
make some decision about error severity for SRAR errors, instead of
retrieving it later in the handler.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/4DEED71A.1060906@jp.fujitsu.com
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The MCE handler uses a special vector for self IPI to invoke
post-emergency processing in an interrupt context, e.g. call an
NMI-unsafe function, wakeup loggers, schedule time-consuming work for
recovery, etc.
This mechanism is now generalized by the following commit:
> e360adbe29
> Author: Peter Zijlstra <a.p.zijlstra@chello.nl>
> Date: Thu Oct 14 14:01:34 2010 +0800
>
> irq_work: Add generic hardirq context callbacks
>
> Provide a mechanism that allows running code in IRQ context. It is
> most useful for NMI code that needs to interact with the rest of the
> system -- like wakeup a task to drain buffers.
:
So change to use provided generic mechanism.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/4DEED6B2.6080005@jp.fujitsu.com
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
More specifically:
- sort bits in the macros
- use BITCLR/BITSET
- coordinate message pattern
- use m for struct mce
- cleanup for severities_debugfs_init()
No functional change.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/4DEED679.9090503@jp.fujitsu.com
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The current format of an item in this table is:
condition(param, ..., level, message [, condition2 ...])
So we have to check both an item's head and tail to find the conditions
which match the item.
Format them in a more straight forward manner:
item(level, message, condition [, condition2 ...])
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/4DEED61F.5010502@jp.fujitsu.com
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The table looks very complicated and hard to read for people other than
skilled developers. So let's clean it up a bit. At first, change format
to ease reading elements in the table.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/4DEED5EB.6050400@jp.fujitsu.com
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The "Spurious not enabled" entry is redundant: the "Not enabled" entry
earlier in the table will cover this case.
The "Action required; unknown MCACOD" entry shouldn't specify MCACOD in
the .mask field. Current code will only match for mcacod==0 rather than
all AR=1 entries.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Link: http://lkml.kernel.org/r/4DEED5BC.8030703@jp.fujitsu.com
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
.. As it won't actually power off the machine.
Reported-by: Sven Köhler <sven.koehler@gmail.com>
Tested-by: Sven Köhler <sven.koehler@gmail.com>
Signed-off-by: Tom Goetz <tom.goetz@virtualcomputer.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The MAXSMP config option requires CPUMASK_OFFSTACK, which in turn
requires we init the memory for the maps while we bring up the cpus.
MAXSMP also increases NR_CPUS to 4096. This increase in size exposed an
issue in the argument construction for multicalls from
xen_flush_tlb_others. The args should only need space for the actual
number of cpus.
Also in 2.6.39 it exposes a bootup problem.
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff8157a1d3>] set_cpu_sibling_map+0x123/0x30d
...
Call Trace:
[<ffffffff81039a3f>] ? xen_restore_fl_direct_reloc+0x4/0x4
[<ffffffff819dc4db>] xen_smp_prepare_cpus+0x36/0x135
..
CC: stable@kernel.org
Signed-off-by: Andrew Jones <drjones@redhat.com>
[v2: Updated to compile on 3.0]
[v3: Updated to compile when CONFIG_SMP is not defined]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Both the equivalence table and the microcode patch types are u32. Access
them properly through the buf-ptr.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
In some rare cases, nmis are generated immediately after the nmi
handler of the cpu was started. This causes the counter not to be
enabled. Before enabling the nmi handlers we need to set variable
ctr_running first and make sure its value is written to memory.
Also, the patch makes all existing barriers a memory barrier instead
of a compiler barrier only.
Reported-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: <stable@kernel.org> # .35+
Signed-off-by: Robert Richter <robert.richter@amd.com>
Swap the 1st and 2nd parameters of save_stack_trace_regs()
as same as the parameters of save_stack_trace_tsk().
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: yrl.pp-manager.tt@hitachi.com
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Namhyung Kim <namhyung@gmail.com>
Link: http://lkml.kernel.org/r/20110608070921.17777.31103.stgit@fedora15
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
[ Also from Ben Hutchings <ben@decadent.org.uk> and Vitaliy Ivanov
<vitalivanov@gmail.com> ]
Commit 06ae40ce07 ("x86 idle: EXPORT_SYMBOL(default_idle, pm_idle)
only when APM demands it") removed the export for pm_idle/default_idle
unless the apm module was modularised and CONFIG_APM_CPU_IDLE was set.
But the apm module uses pm_idle/default_idle unconditionally,
CONFIG_APM_CPU_IDLE only affects the bios idle threshold. Adjust the
export accordingly.
[ Used #ifdef instead of #if defined() as it's shorter, and what both
Ben and Vitaliy used.. Andy, you're out-voted ;) - Linus ]
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Vitaliy Ivanov <vitalivanov@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: Compare only lower 32 bits of framebuffer map offsets
drm/i915: Don't leak in i915_gem_shmem_pread_slow()
drm/radeon/kms: do bounds checking for 3D_LOAD_VBPNTR and bump array limit
drm/radeon/kms: fix mac g5 quirk
x86/uv/x2apic: update for change in pci bridge handling.
alpha, drm: Remove obsolete Alpha support in MGA DRM code
alpha/drm: Cleanup Alpha support in DRM generic code
savage: remove unnecessary if statement
drm/radeon: fix GUI idle IH debug statements
drm/radeon/kms: check modes against max pixel clock
drm: fix fbs in DRM_IOCTL_MODE_GETRESOURCES ioctl
Create a dedicated folder for iommu drivers, and move the base
iommu implementation over there.
Grouping the various iommu drivers in a single location will help
finding similar problems shared by different platforms, so they
could be solved once, in the iommu framework, instead of solved
differently (or duplicated) in each driver.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This finally allows PCI-Device-IDs to be handled by the
IOMMU driver that have no corresponding struct device
present in the system.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Search for existing dev_data first will allow to switch
dev_data->alias to just store dev_data instead of struct
device.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
With this patch the low-level attach/detach functions only
work on dev_data structures. This allows to remove the
dev_data->dev pointer.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch make the functions flushing the DTE and IOTLBs
only take the dev_data structure instead of the struct
device directly.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This list keeps all allocated iommu_dev_data structs in a
list together. This is needed for instances that have no
associated device.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Remove these function calls from places where the function
has already been called by another function.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
When I added 3448a19da4
I forgot about the special uv handling code for this, so this
patch fixes it up.
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Ingo Molnar
Signed-off-by: Dave Airlie <airlied@redhat.com>
Several fixes as well where the +1 was missing.
Done via coccinelle scripts like:
@@
struct resource *ptr;
@@
- ptr->end - ptr->start + 1
+ resource_size(ptr)
and some grep and typing.
Mostly uncompiled, no cross-compilers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Unconditionally changing the address limit to USER_DS and not restoring
it to its old value in the error path is wrong because it prevents us
using kernel memory on repeated calls to this function. This, in fact,
breaks the fallback of hard coded paths to the init program from being
ever successful if the first candidate fails to load.
With this patch applied switching to USER_DS is delayed until the point
of no return is reached which makes it possible to have a multi-arch
rootfs with one arch specific init binary for each of the (hard coded)
probed paths.
Since the address limit is already set to USER_DS when start_thread()
will be invoked, this redundancy can be safely removed.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes the following build failure:
drivers/built-in.o: In function `early_init_dt_check_for_initrd':
/home/florian/dev/kernel/x86/linux-2.6-x86/drivers/of/fdt.c:571:
undefined reference to `early_init_dt_setup_initrd_arch'
make: *** [.tmp_vmlinux1] Error 1
which happens as soon as we enable initrd support on a x86 devicetree
platform such as Intel CE4100.
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Maxime Bizon <mbizon@freebox.fr>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: stable@kernel.org # 2.6.39
Link: http://lkml.kernel.org/r/201106061015.50039.ffainelli@freebox.fr
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We only need to set max_pfn_mapped to the last pfn mapped on x86_64 to
make sure that cleanup_highmap doesn't remove important mappings at
_end.
We don't need to do this on x86_32 because cleanup_highmap is not called
on x86_32. Besides lowering max_pfn_mapped on x86_32 has the unwanted
side effect of limiting the amount of memory available for the 1:1
kernel pagetable allocation.
This patch reverts the x86_32 part of the original patch.
CC: stable@kernel.org
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Lenghty lists of the kind "depends on ARCH1 || ARCH2 ... || ARCH123" are
usually either wrong or too coarse grained. Or plain an ugly sin.
[ tglx: Fixed up amigaone ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linux-alpha@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Gerhard Pircher <gerhard_pircher@gmx.net>
Link: http://lkml.kernel.org/r/20110601180610.984881988@duck.linux-mips.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
x86 defines PIT_LATCH as LATCH which in <linux/timex.h> is defined as
((CLOCK_TICK_RATE + HZ/2) / HZ) and <asm/timex.h> again defines
CLOCK_TICK_RATE as PIT_TICK_RATE.
MIPS defines PIT_LATCH as LATCH which in <linux/timex.h> is defined as
((CLOCK_TICK_RATE + HZ/2) / HZ) and <asm/timex.h> again defines
CLOCK_TICK_RATE as 1193182.
ARM defines PITCH_LATCH as ((PIT_TICK_RATE + HZ / 2) / HZ) - and that's
the sanest thing and equivalent to above definitions so use that as the
new definition in <linux/i8253.h>.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mips@linux-mips.org
Link: http://lkml.kernel.org/r/20110601180610.832810002@duck.linux-mips.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There are multiple declarations of global_clock_event in header files
specific to particular clock event implementations. Consolidate them
in <asm/time.h> and make sure all users include that header.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Venkatesh Pallipadi (Venki) <venki@google.com>
Link: http://lkml.kernel.org/r/20110601180610.762763451@duck.linux-mips.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Move them to drivers/clocksource/i8253.c and remove the
implementations in arch/
[ tglx: Avoid the extra file in lib - folded arch patches in. The
export will become conditional in a later step ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Link: http://lkml.kernel.org/r/20110601180610.221426078@duck.linux-mips.net
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'stable/bug.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: off by one errors in multicalls.c
xen: use the trigger info we already have to choose the irq handler
After a newly plugged CPU sets the cpu_online bit it enables
interrupts and goes idle. The cpu which brought up the new cpu waits
for the cpu_online bit and when it observes it, it sets the cpu_active
bit for this cpu. The cpu_active bit is the relevant one for the
scheduler to consider the cpu as a viable target.
With forced threaded interrupt handlers which imply forced threaded
softirqs we observed the following race:
cpu 0 cpu 1
bringup(cpu1);
set_cpu_online(smp_processor_id(), true);
local_irq_enable();
while (!cpu_online(cpu1));
timer_interrupt()
-> wake_up(softirq_thread_cpu1);
-> enqueue_on(softirq_thread_cpu1, cpu0);
^^^^
cpu_notify(CPU_ONLINE, cpu1);
-> sched_cpu_active(cpu1)
-> set_cpu_active((cpu1, true);
When an interrupt happens before the cpu_active bit is set by the cpu
which brought up the newly onlined cpu, then the scheduler refuses to
enqueue the woken thread which is bound to that newly onlined cpu on
that newly onlined cpu due to the not yet set cpu_active bit and
selects a fallback runqueue. Not really an expected and desirable
behaviour.
So far this has only been observed with forced hard/softirq threading,
but in theory this could happen without forced threaded hard/softirqs
as well. It's probably unobservable as it would take a massive
interrupt storm on the newly onlined cpu which causes the softirq loop
to wake up the softirq thread and an even longer delay of the cpu
which waits for the cpu_online bit.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Peter Zijlstra <peterz@infradead.org>
Cc: stable@kernel.org # 2.6.39
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/amd-iommu: Fix boot crash with hidden PCI devices
x86/amd-iommu: Use only per-device dma_ops
x86/amd-iommu: Fix 3 possible endless loops
* 'kvm-updates/3.0' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: Initialize kvm before registering the mmu notifier
KVM: x86: use proper port value when checking io instruction permission
KVM: add missing void __user * cast to access_ok() call
The generic code always get the device-node in the right place now
so a single implementation will work for all archs
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Michal Simek <monstr@monstr.eu>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
All archs do more or less the same thing now, move it into
a single generic place.
I chose pci.h rather than of_pci.h to avoid having to change
all call-sites to include the later.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Michal Simek <monstr@monstr.eu>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Instead of walking the whole PCI tree to update the of_node's for
PCI busses and devices after the fact, enable the new generic core
code for doing so by providing the proper device nodes for the
PCI host bridges
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Some PCIe cards ship with a PCI-PCIe bridge which is not
visible as a PCI device in Linux. But the device-id of the
bridge is present in the IOMMU tables which causes a boot
crash in the IOMMU driver.
This patch fixes by removing these cards from the IOMMU
handling. This is a pure -stable fix, a real fix to handle
this situation appriatly will follow for the next merge
window.
Cc: stable@kernel.org # > 2.6.32
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
There's a fair amount of code in the vsyscall page. It contains
a syscall instruction (in the gettimeofday fallback) and who
knows what will happen if an exploit jumps into the middle of
some other code.
Reduce the risk by replacing the vsyscalls with short magic
incantations that cause the kernel to emulate the real
vsyscalls. These incantations are useless if entered in the
middle.
This causes vsyscalls to be a little more expensive than real
syscalls. Fortunately sensible programs don't use them.
The only exception is time() which is still called by glibc
through the vsyscall - but calling time() millions of times
per second is not sensible. glibc has this fixed in the
development tree.
This patch is not perfect: the vread_tsc and vread_hpet
functions are still at a fixed address. Fixing that might
involve making alternative patching work in the vDSO.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jesper Juhl <jj@chaosbits.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Jan Beulich <JBeulich@novell.com>
Cc: richard -rw- weinberger <richard.weinberger@gmail.com>
Cc: Mikael Pettersson <mikpe@it.uu.se>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Louis Rilling <Louis.Rilling@kerlabs.com>
Cc: Valdis.Kletnieks@vt.edu
Cc: pageexec@freemail.hu
Link: http://lkml.kernel.org/r/e64e1b3c64858820d12c48fa739efbd1485e79d5.1307292171.git.luto@mit.edu
[ Removed the CONFIG option - it's simpler to just do it unconditionally. Tidied up the code as well. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We're currently missing support for any of the runtime service calls
introduced with the UEFI 2.0 spec in 2006. Add the infrastructure for
supporting them.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Link: http://lkml.kernel.org/r/1307388985-7852-2-git-send-email-mjg@redhat.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Get the information about the VGA console hardware from Xen, and put
it into the form the bootloader normally generates, so that the rest
of the kernel can deal with VGA as usual.
[ Impact: make VGA console work in dom0 ]
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
[v1: Rebased on 2.6.39]
[v2: Removed incorrect comments and fixed compile warnings]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Unfortunatly there are systems where the AMD IOMMU does not
cover all devices. This breaks with the current driver as it
initializes the global dma_ops variable. This patch limits
the AMD IOMMU to the devices listed in the IVRS table fixing
DMA for devices not covered by the IOMMU.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
The driver contains several loops counting on an u16 value
where the exit-condition is checked against variables that
can have values up to 0xffff. In this case the loops will
never exit. This patch fixed 3 such loops.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Commit f6511935f4 moved the permission check for io instructions
to the ->check_perm callback. It failed to copy the port value from RDX
register for string and "in,out ax,dx" instructions.
Fix it by reading RDX register at decode stage when appropriate.
Fixes FC8.32 installation.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Jumping to 0x00 might do something depending on the following
bytes. Jumping to 0xcc is a trap. So fill the unused parts of
the vsyscall page with 0xcc to make it useless for exploits to
jump there.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Cc: Jesper Juhl <jj@chaosbits.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Jan Beulich <JBeulich@novell.com>
Cc: richard -rw- weinberger <richard.weinberger@gmail.com>
Cc: Mikael Pettersson <mikpe@it.uu.se>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Louis Rilling <Louis.Rilling@kerlabs.com>
Cc: Valdis.Kletnieks@vt.edu
Cc: pageexec@freemail.hu
Link: http://lkml.kernel.org/r/ed54bfcfbe50a9070d20ec1edbe0d149e22a4568.1307292171.git.luto@mit.edu
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It just segfaults since April 2008 (a4928cff), so I'm pretty
sure that nothing uses it. And having an empty section makes
the linker script a bit fragile.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Cc: Jesper Juhl <jj@chaosbits.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Jan Beulich <JBeulich@novell.com>
Cc: richard -rw- weinberger <richard.weinberger@gmail.com>
Cc: Mikael Pettersson <mikpe@it.uu.se>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Louis Rilling <Louis.Rilling@kerlabs.com>
Cc: Valdis.Kletnieks@vt.edu
Cc: pageexec@freemail.hu
Link: http://lkml.kernel.org/r/4a4abcf47ecadc269f2391a313576fe6d06acef7.1307292171.git.luto@mit.edu
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently the HPET mapping is a user-accessible syscall
instruction at a fixed address some of the time.
A sufficiently determined hacker might be able to guess when.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Cc: Jesper Juhl <jj@chaosbits.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Jan Beulich <JBeulich@novell.com>
Cc: richard -rw- weinberger <richard.weinberger@gmail.com>
Cc: Mikael Pettersson <mikpe@it.uu.se>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Louis Rilling <Louis.Rilling@kerlabs.com>
Cc: Valdis.Kletnieks@vt.edu
Cc: pageexec@freemail.hu
Link: http://lkml.kernel.org/r/ab41b525a4ca346b1ca1145d16fb8d181861a8aa.1307292171.git.luto@mit.edu
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It's unnecessary overhead in code that's supposed to be highly
optimized. Removing it allows us to remove one of the two
syscall instructions in the vsyscall page.
The only sensible use for it is for UML users, and it doesn't
fully address inconsistent vsyscall results on UML. The real
fix for UML is to stop using vsyscalls entirely.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Cc: Jesper Juhl <jj@chaosbits.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Jan Beulich <JBeulich@novell.com>
Cc: richard -rw- weinberger <richard.weinberger@gmail.com>
Cc: Mikael Pettersson <mikpe@it.uu.se>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Louis Rilling <Louis.Rilling@kerlabs.com>
Cc: Valdis.Kletnieks@vt.edu
Cc: pageexec@freemail.hu
Link: http://lkml.kernel.org/r/973ae803fe76f712da4b2740e66dccf452d3b1e4.1307292171.git.luto@mit.edu
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move vvars out of the vsyscall page into their own page and mark
it NX.
Without this patch, an attacker who can force a daemon to call
some fixed address could wait until the time contains, say,
0xCD80, and then execute the current time.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Cc: Jesper Juhl <jj@chaosbits.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Jan Beulich <JBeulich@novell.com>
Cc: richard -rw- weinberger <richard.weinberger@gmail.com>
Cc: Mikael Pettersson <mikpe@it.uu.se>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Louis Rilling <Louis.Rilling@kerlabs.com>
Cc: Valdis.Kletnieks@vt.edu
Cc: pageexec@freemail.hu
Link: http://lkml.kernel.org/r/b1460f81dc4463d66ea3f2b5ce240f58d48effec.1307292171.git.luto@mit.edu
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It's declared __attribute__((aligned(16)) but it's explicitly
not aligned. This is probably harmless but it's a bit
embarrassing.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Cc: Jesper Juhl <jj@chaosbits.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Jan Beulich <JBeulich@novell.com>
Cc: richard -rw- weinberger <richard.weinberger@gmail.com>
Cc: Mikael Pettersson <mikpe@it.uu.se>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Louis Rilling <Louis.Rilling@kerlabs.com>
Cc: Valdis.Kletnieks@vt.edu
Cc: pageexec@freemail.hu
Link: http://lkml.kernel.org/r/5f3bc5542e9aaa9382d53f153f54373165cdef89.1307292171.git.luto@mit.edu
Signed-off-by: Ingo Molnar <mingo@elte.hu>
While testing the patchset at
http://lkml.kernel.org/r/1306873314-32523-1-git-send-email-bp@alien8.de
with binutils 2.16.1 from hell, kernel build fails with the following
error:
arch/x86/ia32/ia32entry.S: Assembler messages:
arch/x86/ia32/ia32entry.S:139: Error: too many positional arguments
make[2]: *** [arch/x86/ia32/ia32entry.o] Error 1
make[1]: *** [arch/x86/ia32] Error 2
make[1]: *** Waiting for unfinished jobs....
make: *** [arch/x86] Error 2
make: *** Waiting for unfinished jobs....
due to spaces between the operators of the __USER32_CS define. Fix it so
that gas 2.16 can swallow it too.
Signed-off-by: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/1307131642-32595-1-git-send-email-bp@alien8.de
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Drop thunk_ra macro in favor of an additional argument to the thunk
macro since their bodies are almost identical. Do a whitespace scrubbing
and use CFI-aware macros for full annotation.
Signed-off-by: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/1306873314-32523-5-git-send-email-bp@alien8.de
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
b->args[] has MC_ARGS elements, so the comparison here should be
">=" instead of ">". Otherwise we read past the end of the array
one space.
CC: stable@kernel.org
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Enable 64-bit ACPI MFCG support for SGI UV2 platform. The check
is similar to the check on UV1. UV2 has a different oem_id
string.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Link: http://lkml.kernel.org/r/20110602195943.GA27079@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The flags field of struct resource from linux/ioport.h is "unsigned
long". Change the "type" parameter of coalesce_windows() function to
match that field. This fixes the following warning messages when
compiling with "make C=1 W=1 bzImage modules":
arch/x86/pci/acpi.c: In function ‘coalesce_windows’:
arch/x86/pci/acpi.c:198: warning: conversion to ‘long unsigned int’ from ‘int’ may change the sign of the result
arch/x86/pci/acpi.c:203: warning: conversion to ‘long unsigned int’ from ‘int’ may change the sign of the result
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The blacklist was added in response to my bug report
(http://lkml.org/lkml/2006/1/19/362) and has never
contained more than the one entry describing my old
now dead ThinkPad 380XD laptop. As found out later
(http://lkml.org/lkml/2007/11/29/50), this special
treatment has been unnecessary for a long time, so
it can be removed.
Signed-off-by: Tero Roponen <tero.roponen@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
virtio_net: delay TX callbacks
virtio: add api for delayed callbacks
virtio_test: support event index
vhost: support event index
virtio_ring: support event idx feature
virtio ring: inline function to check for events
virtio: event index interface
virtio: add full three-clause BSD text to headers.
virtio balloon: kill tell-host-first logic
virtio console: don't manually set or finalize VIRTIO_CONSOLE_F_MULTIPORT.
drivers, block: virtio_blk: Replace cryptic number with the macro
virtio_blk: allow re-reading config space at runtime
lguest: remove support for VIRTIO_F_NOTIFY_ON_EMPTY.
lguest: fix up compilation after move
lguest: fix timer interrupt setup
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix mwait_play_dead() faulting on mwait-incapable cpus
x86 idle: Fix mwait deprecation warning message
Evil merge to remove extra quote noticed by Joe Perches
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Put back -pg to tsc.o and add no GCOV to vread_tsc_64.o
A logic error in mwait_play_dead() causes the kernel to use
mwait even on cpus which don't support it, such as KVM virtual
cpus.
Introduced by:
349c004e3d31: x86: A fast way to check capabilities of the current cpu
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=36222
Reported-by: Török Edwin <edwintorok@gmail.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/1306758237-9327-1-git-send-email-avi@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
No code changes. Reformat definitions to make it more readable.
I fixed alignment of comments in the structure definitions.
Also aligned comments and most field definitions & values. Also
sorted the defines for the SHIFT & MASK values for each MMR.
This make the file visually much more acceptable.
Some of the symbol names are still quite long. The file is based
on post-processing of verilog definitions that are used for the
node controller chip design. Although some symbol names are not
what I would chose, I would like to maintain compatibility with
the names used by the chip designers. We have a number of
cross-reference utilities & having common names is important.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Link: http://lkml.kernel.org/r/20110527145256.GA31224@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
--
arch/x86/include/asm/uv/uv_mmrs.h | 2873 +++++++++++++++++++++-----------------
1 file changed, 1600 insertions(+), 1273 deletions(-)
Without an IRQ chip set, we now get a WARN_ON and no timer interrupt. This
prevents booting.
Fortunately, the fix is a one-liner: set up the timer IRQ like everything
else.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org # .39.x
* 'idle-release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-idle-2.6:
x86 idle: deprecate mwait_idle() and "idle=mwait" cmdline param
x86 idle: deprecate "no-hlt" cmdline param
x86 idle APM: deprecate CONFIG_APM_CPU_IDLE
x86 idle floppy: deprecate disable_hlt()
x86 idle: EXPORT_SYMBOL(default_idle, pm_idle) only when APM demands it
x86 idle: clarify AMD erratum 400 workaround
idle governor: Avoid lock acquisition to read pm_qos before entering idle
cpuidle: menu: fixed wrapping timers at 4.294 seconds
mwait_idle() is a C1-only idle loop intended to be more efficient
than HLT on SMP hardware that supports it.
But mwait_idle() has been replaced by the more general
mwait_idle_with_hints(), which handles both C1 and deeper C-states.
ACPI uses only mwait_idle_with_hints(), and never uses mwait_idle().
Deprecate mwait_idle() and the "idle=mwait" cmdline param
to simplify the x86 idle code.
After this change, kernels configured with
(!CONFIG_ACPI=n && !CONFIG_INTEL_IDLE=n) when run on hardware
that support MWAIT will simply use HLT. If MWAIT is desired
on those systems, cpuidle and the cpuidle drivers above
can be used.
cc: x86@kernel.org
cc: stable@kernel.org # .39.x
Signed-off-by: Len Brown <len.brown@intel.com>
We'd rather that modern machines not check if HLT works on
every entry into idle, for the benefit of machines that had
marginal electricals 15-years ago. If those machines are still running
the upstream kernel, they can use "idle=poll". The only difference
will be that they'll now invoke HLT in machine_hlt().
cc: x86@kernel.org # .39.x
Signed-off-by: Len Brown <len.brown@intel.com>
We don't want to export the pm_idle function pointer to modules.
Currently CONFIG_APM_CPU_IDLE w/ CONFIG_APM_MODULE forces us to.
CONFIG_APM_CPU_IDLE is of dubious value, it runs only on 32-bit
uniprocessor laptops that are over 10 years old. It calls into
the BIOS during idle, and is known to cause a number of machines
to fail.
Removing CONFIG_APM_CPU_IDLE and will allow us to stop exporting
pm_idle. Any systems that were calling into the APM BIOS
at run-time will simply use HLT instead.
cc: x86@kernel.org
cc: Jiri Kosina <jkosina@suse.cz>
cc: stable@kernel.org # .39.x
Signed-off-by: Len Brown <len.brown@intel.com>
In the long run, we don't want default_idle() or (pm_idle)() to
be exported outside of process.c. Start by not exporting them
to modules, unless the APM build demands it.
cc: x86@kernel.org
cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
The workaround for AMD erratum 400 uses the term "c1e" falsely suggesting:
1. Intel C1E is somehow involved
2. All AMD processors with C1E are involved
Use the string "amd_c1e" instead of simply "c1e" to clarify that
this workaround is specific to AMD's version of C1E.
Use the string "e400" to clarify that the workaround is specific
to AMD processors with Erratum 400.
This patch is text-substitution only, with no functional change.
cc: x86@kernel.org
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, asm: Clean up desc.h a bit
x86, amd: Do not enable ARAT feature on AMD processors below family 0x12
x86: Move do_page_fault()'s error path under unlikely()
x86, efi: Retain boot service code until after switching to virtual mode
x86: Remove unnecessary check in detect_ht()
x86: Reorder mm_context_t to remove x86_64 alignment padding and thus shrink mm_struct
x86, UV: Clean up uv_tlb.c
x86, UV: Add support for SGI UV2 hub chip
x86, cpufeature: Update CPU feature RDRND to RDRAND
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (25 commits)
perf: Fix SIGIO handling
perf top: Don't stop if no kernel symtab is found
perf top: Handle kptr_restrict
perf top: Remove unused macro
perf events: initialize fd array to -1 instead of 0
perf tools: Make sure kptr_restrict warnings fit 80 col terms
perf tools: Fix build on older systems
perf symbols: Handle /proc/sys/kernel/kptr_restrict
perf: Remove duplicate headers
ftrace: Add internal recursive checks
tracing: Update btrfs's tracepoints to use u64 interface
tracing: Add __print_symbolic_u64 to avoid warnings on 32bit machine
ftrace: Set ops->flag to enabled even on static function tracing
tracing: Have event with function tracer check error return
ftrace: Have ftrace_startup() return failure code
jump_label: Check entries limit in __jump_label_update
ftrace/recordmcount: Avoid STT_FUNC symbols as base on ARM
scripts/tags.sh: Add magic for trace-events for etags too
scripts/tags.sh: Fix ctags for DEFINE_EVENT()
x86/ftrace: Fix compiler warning in ftrace.c
...
32bit and 64bit on x86 are tested and working. The rest I have looked
at closely and I can't find any problems.
setns is an easy system call to wire up. It just takes two ints so I
don't expect any weird architecture porting problems.
While doing this I have noticed that we have some architectures that are
very slow to get new system calls. cris seems to be the slowest where
the last system calls wired up were preadv and pwritev. avr32 is weird
in that recvmmsg was wired up but never declared in unistd.h. frv is
behind with perf_event_open being the last syscall wired up. On h8300
the last system call wired up was epoll_wait. On m32r the last system
call wired up was fallocate. mn10300 has recvmmsg as the last system
call wired up. The rest seem to at least have syncfs wired up which was
new in the 2.6.39.
v2: Most of the architecture support added by Daniel Lezcano <dlezcano@fr.ibm.com>
v3: ported to v2.6.36-rc4 by: Eric W. Biederman <ebiederm@xmission.com>
v4: Moved wiring up of the system call to another patch
v5: ported to v2.6.39-rc6
v6: rebased onto parisc-next and net-next to avoid syscall conflicts.
v7: ported to Linus's latest post 2.6.39 tree.
> arch/blackfin/include/asm/unistd.h | 3 ++-
> arch/blackfin/mach-common/entry.S | 1 +
Acked-by: Mike Frysinger <vapier@gentoo.org>
Oh - ia64 wiring looks good.
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The commit 44259b1abf
Author: Andy Lutomirski <luto@MIT.EDU>
x86-64: Move vread_tsc into a new file with sensible options
Removed the -pg from tsc.o which caused the function graph tracer
to go into an infinite function call recursion as it uses the tsc
internally outside its recursion protection, thus tracing the tsc
breaks the function graph tracer.
This commit also added the file vread_tsc_64.c that gets used
by vdso but failed to prevent GCOV from monkeying with it,
causing userspace to try to access kernel data when GCOV was
enabled.
Thanks to Thomas Gleixner for pointing out GCOV as the likely
culprit that added strange kernel accesses into the vread_tsc()
call.
Cc: Author: Andy Lutomirski <luto@MIT.EDU>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PM: Fix PM QOS's user mode interface to work with ASCII input
PM / Hibernate: Update kerneldoc comments in hibernate.c
PM / Hibernate: Remove arch_prepare_suspend()
PM / Hibernate: Update some comments in core hibernate code
* 'upstream/tidy-xen-mmu-2.6.39' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
xen: fix compile without CONFIG_XEN_DEBUG_FS
Use arbitrary_virt_to_machine() to deal with ioremapped pud updates.
Use arbitrary_virt_to_machine() to deal with ioremapped pmd updates.
xen/mmu: remove all ad-hoc stats stuff
xen: use normal virt_to_machine for ptes
xen: make a pile of mmu pvop functions static
vmalloc: remove vmalloc_sync_all() from alloc_vm_area()
xen: condense everything onto xen_set_pte
xen: use mmu_update for xen_set_pte_at()
xen: drop all the special iomap pte paths.
By the previous style change, CONFIG_GENERIC_FIND_NEXT_BIT,
CONFIG_GENERIC_FIND_BIT_LE, and CONFIG_GENERIC_FIND_LAST_BIT are not used
to test for existence of find bitops anymore.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Blackfin arch, like the x86 arch, needs to adjust the PC manually
after a breakpoint is hit as normally this is handled by the remote gdb.
However, rather than starting another arch ifdef mess, create a common
GDB_ADJUSTS_BREAK_OFFSET define for any arch to opt-in via their kgdb.h.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Dongdong Deng <dongdong.deng@windriver.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ns_cgroup is an annoying cgroup at the namespace / cgroup frontier and
leads to some problems:
* cgroup creation is out-of-control
* cgroup name can conflict when pids are looping
* it is not possible to have a single process handling a lot of
namespaces without falling in a exponential creation time
* we may want to create a namespace without creating a cgroup
The ns_cgroup was replaced by a compatibility flag 'clone_children',
where a newly created cgroup will copy the parent cgroup values.
The userspace has to manually create a cgroup and add a task to
the 'tasks' file.
This patch removes the ns_cgroup as suggested in the following thread:
https://lists.linux-foundation.org/pipermail/containers/2009-June/018616.html
The 'cgroup_clone' function is removed because it is no longer used.
This is a userspace-visible change. Commit 45531757b4 ("cgroup: notify
ns_cgroup deprecated") (merged into 2.6.27) caused the kernel to emit a
printk warning users that the feature is planned for removal. Since that
time we have heard from XXX users who were affected by this.
Signed-off-by: Daniel Lezcano <daniel.lezcano@free.fr>
Signed-off-by: Serge E. Hallyn <serge.hallyn@canonical.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Jamal Hadi Salim <hadi@cyberus.ca>
Reviewed-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Paul Menage <menage@google.com>
Acked-by: Matt Helsley <matthltc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: vdso: Remove unused variable
x86-64: Optimize vDSO time()
x86-64: Add time to vDSO
x86-64: Turn off -pg and turn on -foptimize-sibling-calls for vDSO
x86-64: Move vread_tsc into a new file with sensible options
x86-64: Vclock_gettime(CLOCK_MONOTONIC) can't ever see nsec < 0
x86-64: Don't generate cmov in vread_tsc
x86-64: Remove unnecessary barrier in vread_tsc
x86-64: Clean up vdso/kernel shared variables
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
seqlock: Get rid of SEQLOCK_UNLOCKED
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
irq: Remove smp_affinity_list when unregister irq proc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/djm/tmem:
xen: cleancache shim to Xen Transcendent Memory
ocfs2: add cleancache support
ext4: add cleancache support
btrfs: add cleancache support
ext3: add cleancache support
mm/fs: add hooks to support cleancache
mm: cleancache core ops functions and config
fs: add field to superblock to support cleancache
mm/fs: cleancache documentation
Fix up trivial conflict in fs/btrfs/extent_io.c due to includes
Commit b87cf80af3 added support for
ARAT (Always Running APIC timer) on AMD processors that are not
affected by erratum 400. This erratum is present on certain processor
families and prevents APIC timer from waking up the CPU when it
is in a deep C state, including C1E state.
Determining whether a processor is affected by this erratum may
have some corner cases and handling these cases is somewhat
complicated. In the interest of simplicity we won't claim ARAT
support on processor families below 0x12 and will go back to
broadcasting timer when going idle.
Signed-off-by: Boris Ostrovsky <ostr@amd64.org>
Link: http://lkml.kernel.org/r/1306423192-19774-1-git-send-email-ostr@amd64.org
Tested-by: Boris Petkov <borislav.petkov@amd.com>
Cc: Hans Rosenfeld <Hans.Rosenfeld@amd.com>
Cc: Andreas Herrmann <Andreas.Herrmann3@amd.com>
Cc: Chuck Ebbert <cebbert@redhat.com>
Cc: stable@kernel.org # 32.x, 38.x, 39.x
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This patch provides a shim between the kernel-internal cleancache
API (see Documentation/mm/cleancache.txt) and the Xen Transcendent
Memory ABI (see http://oss.oracle.com/projects/tmem).
Xen tmem provides "hypervisor RAM" as an ephemeral page-oriented
pseudo-RAM store for cleancache pages, shared cleancache pages,
and frontswap pages. Tmem provides enterprise-quality concurrency,
full save/restore and live migration support, compression
and deduplication.
A presentation showing up to 8% faster performance and up to 52%
reduction in sectors read on a kernel compile workload, despite
aggressive in-kernel page reclamation ("self-ballooning") can be
found at:
http://oss.oracle.com/projects/tmem/dist/documentation/presentations/TranscendentMemoryXenSummit2010.pdf
Signed-off-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Reviewed-by: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Rik Van Riel <riel@redhat.com>
Cc: Jan Beulich <JBeulich@novell.com>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Andreas Dilger <adilger@sun.com>
Cc: Ted Ts'o <tytso@mit.edu>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <joel.becker@oracle.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Ingo suggested SIGKILL check should be moved into slowpath
function. This will reduce the page fault fastpath impact
of this recent commit:
37b23e0525d3: x86,mm: make pagefault killable
Suggested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: kamezawa.hiroyu@jp.fujitsu.com
Cc: minchan.kim@gmail.com
Cc: willy@linux.intel.com
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/4DDE0B5C.9050907@jp.fujitsu.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
UEFI stands for "Unified Extensible Firmware Interface", where "Firmware"
is an ancient African word meaning "Why do something right when you can
do it so wrong that children will weep and brave adults will cower before
you", and "UEI" is Celtic for "We missed DOS so we burned it into your
ROMs". The UEFI specification provides for runtime services (ie, another
way for the operating system to be forced to depend on the firmware) and
we rely on these for certain trivial tasks such as setting up the
bootloader. But some hardware fails to work if we attempt to use these
runtime services from physical mode, and so we have to switch into virtual
mode. So far so dreadful.
The specification makes it clear that the operating system is free to do
whatever it wants with boot services code after ExitBootServices() has been
called. SetVirtualAddressMap() can't be called until ExitBootServices() has
been. So, obviously, a whole bunch of EFI implementations call into boot
services code when we do that. Since we've been charmingly naive and
trusted that the specification may be somehow relevant to the real world,
we've already stuffed a picture of a penguin or something in that address
space. And just to make things more entertaining, we've also marked it
non-executable.
This patch allocates the boot services regions during EFI init and makes
sure that they're executable. Then, after SetVirtualAddressMap(), it
discards them and everyone lives happily ever after. Except for the ones
who have to work on EFI, who live sad lives haunted by the knowledge that
someone's eventually going to write yet another firmware specification.
[ hpa: adding this to urgent with a stable tag since it fixes currently-broken
hardware. However, I do not know what the dependencies are and so I do
not know which -stable versions this may be a candidate for. ]
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Link: http://lkml.kernel.org/r/1306331593-28715-1-git-send-email-mjg@redhat.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: <stable@kernel.org>
Due to commit dc326fca2b (x86, cpu: Clean up and unify the NOP selection infrastructure), we get the following warning:
arch/x86/kernel/ftrace.c: In function ‘ftrace_make_nop’:
arch/x86/kernel/ftrace.c:308:6: warning: assignment discards qualifiers from pointer target type
arch/x86/kernel/ftrace.c: In function ‘ftrace_make_call’:
arch/x86/kernel/ftrace.c:318:6: warning: assignment discards qualifiers from pointer target type
ftrace_nop_replace() now returns const unsigned char *, so change its associated function/variable to its compatible type to keep compiler clam.
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Link: http://lkml.kernel.org/r/1305221620.7986.4.camel@localhost.localdomain
[ updated for change of const void *src in probe_kernel_write() ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: New driver for the SMSC EMC6W201
hwmon: (abituguru) Depend on DMI
hwmon: (it87) Use request_muxed_region
hwmon: (sch5627) Trigger Vbat measurements
hwmon: (sch5627) Add sch5627_send_cmd function
i8k: Integrate with the hwmon subsystem
hwmon: (max6650) Properly support the MAX6650
hwmon: (max6650) Drop device detection
Move ACPI power meter driver to hwmon
hwmon: (f71882fg) Add support for F71808A
hwmon: (f71882fg) Split has_beep in fan_has_beep and temp_has_beep
hwmon: (asc7621) Drop duplicate dependency
hwmon: (jc42) Change detection class
hwmon: Add driver for AMD family 15h processor power information
hwmon: (k10temp) Add support for Fam15h (Bulldozer)
hwmon: Use helper functions to set and get driver data
i8k: Avoid lahf in 64-bit code
This patch removes a check that causes incorrect scheduler
domain setup (SMP instead of SMT) and bootlog warning messages
when cpuid extensions for topology enumeration are not supported
and the number of processors reported to the OS is smaller than
smp_num_siblings.
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Nikhil P Rao <nikhil.rao@intel.com>
Link: http://lkml.kernel.org/r/1306343921.19325.1.camel@fedora13
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This has been obsoleted by the root= commandline and the rdev utility
for many, many years. People who still depend on this will surely
have a copy of the rdev utility around, the rest of the world gets rid
of another piece of buildhost-dependent data in the build. Thanks to
Paul Bolle for the build.c cleanup.
Cc: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Link: http://lkml.kernel.org/r/1302607824-24699-1-git-send-email-mmarek@suse.cz
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Let i8k create an hwmon class device so that libsensors will expose
the CPU temperature and fan speeds to monitoring applications.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Massimo Dal Zotto <dz@debian.org>
Most arches define CONFIG_DEBUG_STACK_USAGE exactly the same way. Move it
to lib/Kconfig.debug so each arch doesn't have to define it. This
obviously makes the option generic, but that's fine because the config is
already used in generic code.
It's not obvious to me that sysrq-P actually does anything caution by
keeping the most inclusive wording.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Richard Weinberger <richard@nod.at>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
DEBUG_PER_CPU_MAPS is used in lib/cpumask.c as well as in
inlcude/linux/cpumask.h and thus it has outgrown its use within x86 and
powerpc alone. Any arch with SMP support may want to get some more
debugging, so make this option generic.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: <linux-arch@vger.kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On larger systems, because of the numerous ACPI, Bootmem and EFI messages,
the static log buffer overflows before the larger one specified by the
log_buf_len param is allocated. Minimize the overflow by allocating the
new log buffer as soon as possible.
On kernels without memblock, a later call to setup_log_buf from
kernel/init.c is the fallback.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix CONFIG_PRINTK=n build]
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The presense of a writeq() implementation on 32-bit x86 that splits the
64-bit write into two 32-bit writes turns out to break the mpt2sas driver
(and in general is risky for drivers as was discussed in
<http://lkml.kernel.org/r/adaab6c1h7c.fsf@cisco.com>). To fix this,
revert 2c5643b1c5 ("x86: provide readq()/writeq() on 32-bit too") and
follow-on cleanups.
This unfortunately leads to pushing non-atomic definitions of readq() and
write() to various x86-only drivers that in the meantime started using the
definitions in the x86 version of <asm/io.h>. However as discussed
exhaustively, this is actually the right thing to do, because the right
way to split a 64-bit transaction is hardware dependent and therefore
belongs in the hardware driver (eg mpt2sas needs a spinlock to make sure
no other accesses occur in between the two halves of the access).
Build tested on 32- and 64-bit x86 allmodconfig.
Link: http://lkml.kernel.org/r/x86-32-writeq-is-broken@mdm.bga.com
Acked-by: Hitoshi Mitake <h.mitake@gmail.com>
Cc: Kashyap Desai <Kashyap.Desai@lsi.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Ravi Anand <ravi.anand@qlogic.com>
Cc: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Jason Uhlenkott <juhlenko@akamai.com>
Acked-by: James Bottomley <James.Bottomley@parallels.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change each shrinker's API by consolidating the existing parameters into
shrink_control struct. This will simplify any further features added w/o
touching each file of shrinker.
[akpm@linux-foundation.org: fix build]
[akpm@linux-foundation.org: fix warning]
[kosaki.motohiro@jp.fujitsu.com: fix up new shrinker API]
[akpm@linux-foundation.org: fix xfs warning]
[akpm@linux-foundation.org: update gfs2]
Signed-off-by: Ying Han <yinghan@google.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Acked-by: Pavel Emelyanov <xemul@openvz.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
cpumask_t is very big struct and cpu_vm_mask is placed wrong position.
It might lead to reduce cache hit ratio.
This patch has two change.
1) Move the place of cpumask into last of mm_struct. Because usually cpumask
is accessed only front bits when the system has cpu-hotplug capability
2) Convert cpu_vm_mask into cpumask_var_t. It may help to reduce memory
footprint if cpumask_size() will use nr_cpumask_bits properly in future.
In addition, this patch change the name of cpu_vm_mask with cpu_vm_mask_var.
It may help to detect out of tree cpu_vm_mask users.
This patch has no functional change.
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Straightforward conversion of i_mmap_lock to a mutex.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Miller <davem@davemloft.net>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Tony Luck <tony.luck@intel.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nadav Har'El