Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adding defines for RAID10 and RAID50 levels, in preparation
of adding RAID Transport support in the mpt fusion drivers.
(BTW: IME is RAID10, and IM is RAID1).
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
we always set ->SCp.ptr to physical address of buffer; for DMA that's
just what we need, but we end up using it as virtual address in PIO
case of esp_do_data(), with obvious breakage as soon as memory mapping
becomes non-trivial. The fix is obvious.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
oktagon_esp is described as modular. However, drivers/scsi/Makefile doesn't
handle it right - it's multi-object module, with one of the parts being built
from .S. Current makefile tries to declare each part a module of its own;
that not only wouldn't work (oktagon_io.o doesn't have the right parts for
that), it actually doesn't even build since kbuild doesn't believe in
single-object modules built from .S. Turned into proper multi-object
module...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
in amigahw.h custom renamed to amiga_custom, in drivers with few instances the
same replacement, in the rest - #define custom amiga_custom in driver itself
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
These days ioctl32.h is only used for communication of fs/compat.c and
fs/compat_ioctl.c and doesn't contain anything of interest to drivers.
Remove inclusion in various drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sg_page_malloc should clear the data buffer, not that extent of mem_map.
This fixes Jesper's sg_page_free "Bad page states"
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch works around a problem with spurious interrupts seen at boot time when
a MAXTOR 6H500F0 drive is present. An ATA interrupt condition is mysteriously
present at start of day. If we took too long in issuing the first command,
the kernel would basically get tired of the spurious interrupts and turn the interrupt
off. Issuing the first command essentially causes the interrupt condition to
get acknowledged.
I haven't seen this happen with any other drives.
What I basically do is ack ATA status by reading it regardless of whether we're
expecting to have to handle an interrupt. This clears the start-of-day anomalous
interrupt condition, and keeps the kernel from disabling that interrupt due to
too many spurious interrupts.
Also, I fixed a bug where hotplug interrupts weren't getting acknowledged as handled
in the ISR. This was not the cause of the spurious interrupts, but it's the right
thing to do anyway.
Signed-Off-By: Andrew Chew
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch moves the SCSI softirq handling to the block layer version.
There should be no functional changes.
Signed-off-by: Jens Axboe <axboe@suse.de>
Many ARM drivers do not need to include asm/irq.h - remove this
unnecessary include from some ARM drivers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
HDIO_GETGEO is implemented in most block drivers, and all of them have to
duplicate the code to copy the structure to userspace, as well as getting
the start sector. This patch moves that to common code [1] and adds a
->getgeo method to fill out the raw kernel hd_geometry structure. For many
drivers this means ->ioctl can go away now.
[1] the s390 block drivers are odd in this respect. xpram sets ->start
to 4 always which seems more than odd, and the dasd driver shifts
the start offset around, probably because of it's non-standard
sector size.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@suse.de>
Cc: <mike.miller@hp.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The pre-parsed addrs/n_addrs fields in struct device_node are finally
gone. Remove the dodgy heuristics that did that parsing at boot and
remove the fields themselves since we now have a good replacement with
the new OF parsing code. This patch also fixes a bunch of drivers to use
the new code instead, so that at least pmac32, pseries, iseries and g5
defconfigs build.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds suspend patch to libata, and ata_piix in particular. For
most low level drivers, they should just need to add the 4 hooks to
work. As I can only test ata_piix, I didn't enable it for more
though.
Suspend support is the single most important feature on a notebook, and
most new notebooks have sata drives. It's quite embarrassing that we
_still_ do not support this. Right now, it's perfectly possible to
suspend the drive in mid-transfer.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make drivers that use directly PC parport HW depend on PARPORT_PC rather than
HW independent PARPORT.
Signed-off-by: Marko Kohtala <marko.kohtala@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sanitize some s390 Kconfig options. We have ARCH_S390, ARCH_S390X,
ARCH_S390_31, 64BIT, S390_SUPPORT and COMPAT. Replace these 6 options by
S390, 64BIT and COMPAT.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reflect changes in SCSI midlayer and updated to use new
ordered request implementation
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
All ordered request related stuff delegated to HLD. Midlayer
now doens't deal with ordered setting or prepare_flush
callback. sd.c updated to deal with blk_queue_ordered
setting. Currently, ordered tag isn't used as SCSI midlayer
cannot guarantee request ordering.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
add @uptodate argument to end_that_request_last() and @error
to rq_end_io_fn(). there's no generic way to pass error code
to request completion function, making generic error handling
of non-fs request difficult (rq->errors is driver-specific and
each driver uses it differently). this patch adds @uptodate
to end_that_request_last() and @error to rq_end_io_fn().
for fs requests, this doesn't really matter, so just using the
same uptodate argument used in the last call to
end_that_request_first() should suffice. imho, this can also
help the generic command-carrying request jens is working on.
Signed-off-by: tejun heo <htejun@gmail.com>
Signed-Off-By: Jens Axboe <axboe@suse.de>
Unify the EVENT_CARD_INSERTION and "attach" callbacks to one unified
probe() callback. As all in-kernel drivers are changed to this new
callback, there will be no temporary backwards-compatibility. Inside a
probe() function, each driver _must_ set struct pcmcia_device
*p_dev->instance and instance->handle correctly.
With these patches, the basic driver interface for 16-bit PCMCIA drivers
now has the classic four callbacks known also from other buses:
int (*probe) (struct pcmcia_device *dev);
void (*remove) (struct pcmcia_device *dev);
int (*suspend) (struct pcmcia_device *dev);
int (*resume) (struct pcmcia_device *dev);
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The linked list of devices managed by each PCMCIA driver is, in very most
cases, unused. Therefore, remove it from many drivers.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Unify the "detach" and REMOVAL_EVENT handlers to one "remove" function.
Old functionality is preserved, for the moment.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Move the suspend and resume methods out of the event handler, and into
special functions. Also use these functions for pre- and post-reset, as
almost all drivers already do, and the remaining ones can easily be
converted.
Bugfix to include/pcmcia/ds.c
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Leave the overloaded "hotplug" word to susbsystems which are handling
real devices. The driver core does not "plug" anything, it just exports
the state to userspace and generates events.
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The distinction between hotplug and uevent does not make sense these
days, netlink events are the default.
udev depends entirely on netlink uevents. Only during early boot and
in initramfs, /sbin/hotplug is needed. So merge the two functions and
provide only one interface without all the options.
The netlink layer got a nice generic interface with named slots
recently, which is probably a better facility to plug events for
subsystem specific events.
Also the new poll() interface to /proc/mounts is a nicer way to
notify about changes than sending events through the core.
The uevents should only be used for driver core related requests to
userspace now.
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ignore all files generated from *_shipped files, plus a few others.
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
The oops is characteristic of the underlying device being removed from
visibility before the class device, and sure enough we do device_del()
before transport_unregister() in the scsi_target_reap() routines. I've
no idea why this is suddenly showing up, since the code has been in
there since that function was first invented. However, I've confirmed
this fixes Andrew Vasquez's boot oops.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch prevents libata from incorrectly modifying inquiry
VPD pages and command support data from ATAPI devices. I have tested
the patch with a SATA ATAPI tape drive on an AHCI controller.
Patch is against kernel 2.4.32 with 2.4.32-libata1.patch applied.
Anthony J. Battersby
Cybernetics
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Miquel van Smoorenburg <miquels@cistron.nl> forwarded me this fix to
resolve a deadlock condition that occurs due to the API change in
2.6.13+ kernels dropping the host locking when entering the error
handling. They all end up calling adpt_i2o_post_wait(), which if you
call it unlocked, might return with host_lock locked anyway and that
causes a deadlock.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix compile warnings with current scsi-misc git tree
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
scsi_reap_target() was desgined to be called from any context.
However it must do a device_del() of the target device, which may only
be called from user context. Thus we have to reimplement
scsi_reap_target() via a workqueue.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When the sym1 driver was in the tree, it used to share various parts of
its infrastructure with the ncr driver. Now it's gone, these files are
just an annoyance, so merge sym53c8xx_comm.h into ncr53c8xx.c and merge
sym53c8xx_defs.h into ncr53c8xx.h.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The ncr53c8xx driver had its own loop to print scsi messages. Use the
SPI one instead.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This update now allows this driver to be used on big endian bus
machines that aren't parisc. To do that, the driver must set a
CONFIG_53C700_BE_BUS in Kconfig to compile the right macro versions.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In the scenario that a link was broken, the devloss timer for each
rport was expire at roughly the same time, causing lots of "delete"
workqueue items being queued. Depth is dependent upon the number of
rports that were on the link.
The rport target remove calls were calling flush_scheduled_work(),
which would interrupt the stream, and start the next workqueue item,
which did the same thing, and so on until recursion depth was large.
This fix stops the recursion in the initial delete path, and pushes it
off to a host-level work item that reaps the dead rports.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Introduce a new helper, print_nego() to handle SDTR/WDTR/PPR.
Split out the guts of show_spi_transport_period_helper() into period_to_str()
and use it in print_nego to get the period factor conversion right.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Replace the custom NO_*_MSGS definitions with uses of ARRAY_SIZE.
This fixes a bug in the definition of NO_EXTENDED_MSGS.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A missing comma meant that "Ordered Queue Tag" and "Ignore Wide Residue"
were being concatenated together.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Rename scsi_print_msg to spi_print_msg and move its prototype from
scsi_dbg.h to scsi_transport_spi.h
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
scsi_print_msg() is an SPI-specific concept. This patch moves it from
constants.c to scsi_transport_spi.c and updates the Kconfig to link in
the SPI class for the drivers which use scsi_print_msg().
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This merge is pretty extensive. The conflict is over the new
req->retries parameter, so I had to change the prototype to
scsi_setup_blk_pc_cmnd() and the usage in sd, sr and st.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Patch from Kai minus last sg_segs clearing which was merged already.
> > Was there a oops or lockup or any debug output you can send me? I will try
> > some more large request tests with scsi_debug. You also have to compile your
> > kernel with SCSI_MAX_PHYS_SEGMENTS == 255 to get larger requests now.
>
It was an oops in sgl_unmap_user_pages(). The reason is this:
/* XXX: just for debug. Remove when PageReserved is removed */
BUG_ON(PageReserved(page));
I was using /dev/zero as input and it triggers this. When I used a file as
input, this did not trigger. Should this BUG_ON be removed?
In the same log I noticed that there was another ->sg_segs inconsistency.
Also, the field ->last_SRpnt was not reset when scsi_execute_async()
failed. This caused the error message "Async command already active"
later and prevented proper close.
While doing the changes, I noticed that the current code (since
2.6.0-test4) does not set the pages dirty when reading with direct i/o.
All of these st problems (including the one I sent earlier) are fixed in
the patch at the end of this message. These fixes should probably be
included already in 2.6.15.
After these fixes, the tape seems to operate as expected. Without other
changes, the largest block size with sym53c896 SCSI adapter is 384 kB. The
maximum number of sg segments is set to 96 and clustering is disabled in
the driver. 96 x 4 kB = 384 kB. OK.
I enabled clustering and set max_sectors to 10000 in the SCSI HBA driver.
Now the block size limit is 5000 kB as expected.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- export __blk_put_request and blk_execute_rq_nowait
needed for async REQ_BLOCK_PC requests
- seperate max_hw_sectors and max_sectors for block/scsi_ioctl.c and
SG_IO bio.c helpers per Jens's last comments. Since block/scsi_ioctl.c SG_IO was
already testing against max_sectors and SCSI-ml was setting max_sectors and
max_hw_sectors to the same value this does not change any scsi SG_IO behavior. It only
prepares ll_rw_blk.c, scsi_ioctl.c and bio.c for when SCSI-ml begins to set
a valid max_hw_sectors for all LLDs. Today if a LLD does not set it
SCSI-ml sets it to a safe default and some LLDs set it to a artificial low
value to overcome memory and feedback issues.
Note: Since we now cap max_sectors to BLK_DEF_MAX_SECTORS, which is 1024,
drivers that used to call blk_queue_max_sectors with a large value of
max_sectors will now see the fs requests capped to BLK_DEF_MAX_SECTORS.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
convert st to always send scatterlists and kill scsi_request
usage.
This is the same as last time as it was posted, but with Kai's patches
merged and we now pass the bytes value to scsi_execute_async.
TODO:
- move DIO code to common place or make block layers usable for ULDs.
- move buffer allocation code to common place for all ULDs to use. And
make buffer allocation code handle all queue limits so we can find
out about problems before calling scsi_execute_async.
- move indirect (copy_to/from_user) paths commone place or make block
layers usable for ULDs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Convert sg to always send scatterlists, and kill scsi_request usage.
TODO:
- move DIO code to common place or make block layers usable for ULDs.
- move buffer allocation code to common place for all ULDs to use. And
make buffer allocation code obey all queue limits so we can find
out about problems before calling scsi_execute_async. Currently, sg.c
could allocate a buffer that is too large, and send the request
to scsi_execute_async. scsi_execute_async will then check it against
all the queue limits and return a failure in this case. It would nicer
to know about the queue limit violation right away.
- move indirect (copy_to/from_user) paths commone place or make block
layers usable for ULDs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add kmemcache of scsi io contexts.
In the future when we finalize on where these functions will live
we can add a mempool for it and do a bioset for out REQ_BLOCK_PC
bios. This is needed becuase the dm-multipath handlers will
want to use the scsi_exectute* functions for failover and we cannot
have them and the bio device allocating from the same mempool.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
sd does not allow scsi_io_completion to retry commands for
SG_IO requests, and it make sense that it should not happen for st
SG_IO commands too. If for st we hit the bottom of scsi_io_completion
we will probably screw things up pretty bad. This patch returns to the
block layer that the whole command completed and relies on the caller to check
the request errors field. For initialization commands like in sd, this adds
the previous behavior where scsi_io_completion did not process the error.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
For tape we need to control the retries. This patch adds a retries
counter on the request for REQ_BLOCK_PC commands originating from
scsi_execute* to use. REQ_BLOCK_PC commands comming from the block
layer SG_IO path continue to use the retires set in the ULD init_command.
(scsi_execute* does not set the gendisk so we do not execute
the init_command in that path).
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add scsi helpers to create really-large-requests and convert
scsi-ml to scsi_execute_async().
Per Jens's previous comments, I placed this function in scsi_lib.c.
I made it follow all the queue's limits - I think I did at least :), so
I removed the warning on the function header.
I think the scsi_execute_* functions should eventually take a request_queue
and be placed some place where the dm-multipath hw_handler can use them
if that failover code is going to stay in the kernel. That conversion
patch will be sent in another mail though.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add scsi_add_host() failure handling for aic7xxx
Also silence a compiler warning :
drivers/scsi/aic7xxx/aic7xxx_osm.c: In function `ahc_linux_register_host':
drivers/scsi/aic7xxx/aic7xxx_osm.c:1100: warning: ignoring return value of `scsi_add_host', declared with attribute warn_unused_result
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add scsi_add_host() failure handling for aic79xx
Also silence a compiler warning :
drivers/scsi/aic7xxx/aic79xx_osm.c: In function `ahd_linux_register_host':
drivers/scsi/aic7xxx/aic79xx_osm.c:1099: warning: ignoring return value of `scsi_add_host', declared with attribute warn_unused_result
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This follows on from Jens' patch and consolidates all of the ULD
separate handlers for REQ_BLOCK_PC into a single call which has his
fix for our direction bug.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Since nobody has offered an explanation for why the sd driver makes a
write-protect check only for devices with removable media, I'm submitting
this patch to get rid of the removable-media test.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Add functionality to run in polled mode only. Includes run time
attribute to enable mode.
- Enable runtime writable hba settings for coallescing and delay parameters
Customers have requested a mode in the driver to run strictly polled.
This is generally to support an environment where the server is extremely
loaded and is looking to reclaim some cpu cycles from adapter interrupt
handling.
This patch adds a new "poll" attribute, and the following behavior:
if value is 0 (default):
The driver uses the normal method for i/o completion. It uses the
firmware feature of interrupt coalesing. The firmware allows a
minimum number of i/o completions before an interrupt, or a maximum
time delay between interrupts. By default, the driver sets these
to no delay (disabled) or 1 i/o - meaning coalescing is disabled.
Attributes were provided to change the coalescing values, but it was
a module-load time only and global across all adapters.
This patch allows them to be writable on a per-adapter basis.
if value is 1 :
Interrupts are left enabled, expecting that the user has tuned the
interrupt coalescing values. When this setting is enabled, the driver
will attempt to service completed i/o whenever new i/o is submitted
to the adapter. If the coalescing values are large, and the i/o
generation rate steady, an interrupt will be avoided by servicing
completed i/o prior to the coalescing thresholds kicking in. However,
if the i/o completion load is high enough or i/o generation slow, the
coalescion values will ensure that completed i/o is serviced in a timely
fashion.
if value is 3 :
Turns off FCP i/o interrupts altogether. The coalescing values now have
no effect. A new attribute "poll_tmo" (default 10ms) exists to set
the polling interval for i/o completion. When this setting is enabled,
the driver will attempt to service completed i/o and restart the
interval timer whenever new i/o is submitted. This behavior allows for
servicing of completed i/o sooner than the interval timer, but ensures
that if no i/o is being issued, then the interval timer will kick in
to service the outstanding i/o.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Release task management command before counting outstanding commands.
TMF was being erroneously counted as an active outstanding command.
- Serialize EH calls and block requests when EH function is running.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove locking wrappers around error handlers. Wrappers were added in
early 2.6.13 api change
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Remove unnecessary scsi_block_requests calls on rport deletes.
This was deadlocking the sdev removals as they wanted to flush commands.
- No longer block requests when adding the remote port (to block
discovery). Instead, register, then change port role. Maps to Qlogic
behavior, and closer to the register-node-upon-first-ELS behavior.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Cause: Link bounces were causing discovery ELS's to be killed.
Driver was not properly flushing ELS commands upon the subsequent
link bounces. Thus, processing of ELS post link bounce erroneously
assumed discovery failure and device loss.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Miscellaneous Cleanups:
- Remove ProgType READ_REV mailbox command value check in lpfc_config_port_prep.
- Convert simple printk to an lpfc_printf_log in queuecommand.
- Modify lpfc_abort_handler message 0749 to display more accurate text and data.
- Minor style cleanup: fix 3 long lines in lpfc_hw.h
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Make the vendor, model and rev fields in scsi_device pointers to const
and update a few prototypes of functions using them.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From Wang Zhenyu:
check header digest for cmd and mgmt tasks
Signed-off-by: Wang Zhenyu <zhenyu.z.wang@intel.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From Wang Zhenyu:
High queue depth was a problem for some targets so make queue_depth adjustable
From Mike Christie
Make default queue_depth a little lower
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From Wang Zhenyu:
data digest fix (the bug caused data corruption w/Wasabi StorageBuilder target)
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
from Wang Zhenyu:
Must check SCSI CMD and R2T response according to the spec
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From tomof@acm.org:
There is one more issue about Equallogic systems. They send
re-direction info with FIN. I think that the kernel module needs to
let iscsid to read data from the socket before killing it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Must check only valid opcode bits.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Rather than print a list of targets at driver init time, print each
disabled target as we attempt to scan it.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The NVRAM for both Tekram and Symbios boards allows the user to set the
speed and width for individual targets. I took that code out in March
2004 when we introduced Domain Validation, but it seems there's still
a legitimate need for it in some configurations.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
sym_show_msg was almost a duplicate of scsi_print_msg, except not as
featureful. So use the common code instead.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Now that this constant has been added to dma-mapping.h, we don't need our
own definition
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The upper layer doesn't send these down since 2.4.x (or 2.6 in
practice), so no need to handle it. Inline sym_setup_data_pointers
into its only caller so we can fail gracefully in the case we'd get
one neverless.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
