There's currently a diagnostic printk in relay_switch_subbuf() meant as
a warning if you accidentally try to log an event larger than the
sub-buffer size.
The problem is if this happens while logging from somewhere it's not
safe to be doing printks, such as in the scheduler, you can end up with
a deadlock. This patch removes the warning from relay_switch_subbuf()
and instead prints some diagnostic info when the channel is closed.
Thanks to Mathieu Desnoyers for pointing out the problem and
suggesting a fix.
Signed-off-by: Tom Zanussi <zanussi@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Ensure we call unmap_mapping_range() and sync dirty pages to disk before
doing an NFS direct write.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
When we insert a new xfrm_state which potentially
subsumes an existing one, make sure all cached
bundles are flushed so that the new SA is used
immediately.
Signed-off-by: David S. Miller <davem@davemloft.net>
I reported a problem and gave hints to the solution, but nobody seemed
to react. So I prepared a patch against 2.6.14.4.
Tested on 2.6.14.4 with "ip monitor addr" and with the program
attached, while adding and removing IPv6 address. Both programs didn't
receive any messages. Tested 2.6.14.4 + this patch, and both programs
received add and remove messages.
Signed-off-by: Kristian Slavov <kristian.slavov@nomadiclab.com>
Acked-by: Jamal Hadi salim <hadi@cyberus.ca>
ACKed-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This (and the three subsequent patches) is working well on OMAP H4 with
2.6.15-rc4 kernel and passes the LTP fs test.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
DMA_MODE_{READ,WRITE} are declared in asm-powerpc/dma.h and their
declarations there match the definitions. Old declarations in
ppc4xx_dma.h are not right anymore (wrong type, to start with).
Killed them, added include of asm/dma.h where needed.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sparc64, i386 and x86_64 have support for a special data section dedicated
to rarely updated data that is frequently read. The section was created to
avoid false sharing of those rarely read data with frequently written kernel
data.
This patch creates such a data section for ia64 and will group rarely written
data into this section.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The logic that decides that a fork() might be able to avoid copying a VM
area when it can be re-created by page faults didn't know about the new
vm_insert_page() case.
Also make some things a bit more anal wrt VM_PFNMAP.
Pointed out by Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The udelay() inline for ia64 uses the ITC. If CONFIG_PREEMPT is enabled
and the platform has unsynchronized ITCs and the calling task migrates
to another CPU while doing the udelay loop, then the effective delay may
be too short or very, very long.
This patch disables preemption around 100 usec chunks of the overall
desired udelay time. This minimizes preemption-holdoffs.
udelay() is now too big to be inline, move it out of line and export it.
Signed-off-by: John Hawkes <hawkes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Changes here include removing all of CONFIG_PM while it is being repeatedly
smacked with a lead pipe, moving the BURSTMODE param to a #define (it should
be defined almost always anyway), fixing the rqsize stuff, pulling ide_ioreg_t,
and general cleanups and whatnot.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Some motherboards (such as the Asus P5V800-MX) ship a
PCI_DEVICE_ID_VIA_82C586_1 IDE controller alongside a VT8251 southbridge.
This southbridge is currently unrecognised in the via82cxxx IDE driver,
preventing those users from getting DMA access to disks.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Patch from Daniel Jacobowitz
Handle new EABI relocations when loading kernel modules. This is
necessary for CONFIG_AEABI kernels, and also for some broken
(since fixed) old ABI toolchains.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This follows on from Jens' patch and consolidates all of the ULD
separate handlers for REQ_BLOCK_PC into a single call which has his
fix for our direction bug.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
ERR_SEVERITY item is defined as a 8 bits item in SAL documentation
($B.2.1 rev december 2003), but as an u16 in sal.h.
This has the side effect that current code in mca.c may not call
ia64_sal_clear_state_info() upon receiving corrected platform errors
if there are bits set in the validation byte. Reported by Xavier Bru.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Some hardware does not support the PACKET command at all.
Other hardware supports ATAPI, but the driver does something nasty such
as calling BUG() when an ATAPI command is issued.
For these such cases, we mark them with a new flag, ATA_FLAG_NO_ATAPI.
Initial version contributed by Ben Collins.
The drawing function cfbfillrect does not work correctly when access is not
unsigned-long aligned. It manifests as extra lines of pixels that are not
complete drawn. Reversing the shift operator solves the problem, so I would
presume that this bug would manifest only on little endian machines. The
function cfbcopyarea may also have this bug.
Aligned access should present no problems.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Every framebuffer driver relies on the assumption that the set_par()
function of the driver is called before drawing functions and other
functions dependent on the hardware state are executed.
Whenever you switch from X to a framebuffer console for the very first
time, there is a chance that a broken X system has _not_ set the mode to
KD_GRAPHICS, thus the vt and framebuffer code executes a screen redraw and
several other functions before a set_par() is executed. This is believed
to be not a bug of linux but a bug of X/xdm. At least some X releases used
by SuSE and Debian show this behaviour.
There was a 2nd case, but that has been fixed by Antonino Daplas on
10-dec-2005.
This patch allows drivers to set a flag to inform fbcon_switch() that they
prefer a set_par() call on every console switch, working around the
problems caused by the broken X releases.
The flag will be used by the next release of cyblafb and might help other
drivers that assume a hardware state different to the one used by X.
As the default behaviour does not change, this patch should be acceptable
to everybody.
Signed-off-by: Knut Petersen <Knut_Petersen@t-online.de>
Acked-by: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add hooks to save and restore the graphics state. These hooks are called in
fbcon_blank() when entering/leaving KD_GRAPHICS mode. This is needed by
savagefb at least so it can cooperate with savage_dri and by cyblafb.
State save/restoration can be full or partial.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Spotted by a Fedora user. Compiling with DEBUG_PARPORT set fails due to
the broken cast.
Just remove it.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When multiple probes are registered at the same address and if due to some
recursion (probe getting triggered within a probe handler), we skip calling
pre_handlers and just increment nmissed field.
The below patch make sure it walks the list for multiple probes case.
Without the below patch we get incorrect results of nmissed count for
multiple probe case.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For Kprobes critical path is the path from debug break exception handler
till the control reaches kprobes exception code. No probes can be
supported in this path as we will end up in recursion.
This patch prevents this by moving the below function to safe __kprobes
section onto which no probes can be inserted.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The below patch lets userspace have more control over the inodes that
inotify will watch. It introduces two new flags.
IN_ONLYDIR -- only watch the inode if it is a directory.
This is needed to avoid the race that can occur when we want to be
sure that we are watching a directory.
IN_DONT_FOLLOW -- don't follow a symlink. In combination
with IN_ONLYDIR we can make sure that we don't watch the target of
symlinks.
The issues the flags fix came up when writing the gnome-vfs inotify
backend. Default behaviour is unchanged.
Signed-off-by: John McCutchan <ttb@tentacle.dhs.org>
Acked-by: Robert Love <rml@novell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add list_replace_rcu: replace old entry by new one.
Signed-off-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds a timestamp field to the events sent via the process event
connector. The timestamp allows listeners to accurately account the
duration(s) between a process' events and offers strong means with which
to determine the order of events with respect to a given task while also
avoiding the addition of per-task data.
This alters the size and layout of the event structure and hence would
break compatibility if process events connector as it stands in 2.6.15-rc2
were released as a mainline kernel.
Signed-off-by: Matt Helsley <matthltc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are several functions that might seem appropriate for a timestamp:
get_cycles()
current_kernel_time()
do_gettimeofday()
<read jiffies/jiffies_64>
Each has problems with combinations of SMP-safety, low resolution, and
monotonicity. This patch adds a new function that returns a monotonic SMP-safe
timestamp with nanosecond resolution where available.
Changes:
Split timestamp into separate patch
Moved to kernel/time.c
Renamed to getnstimestamp
Fixed unintended-pointer-arithmetic bug
Signed-off-by: Matt Helsley <matthltc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This introduces a new interface - rcu_barrier() which waits until all
the RCUs queued until this call have been completed.
Reiser4 needs this, because we do more than just freeing memory object
in our RCU callback: we also remove it from the list hanging off
super-block. This means, that before freeing reiser4-specific portion
of super-block (during umount) we have to wait until all pending RCU
callbacks are executed.
The only change of reiser4 made to the original patch, is exporting of
rcu_barrier().
Cc: Hans Reiser <reiser@namesys.com>
Cc: Vladimir V. Saveliev <vs@namesys.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
IA64 is using the generic version of __raw_read_trylock, which always
waits for the lock to be free instead of returning when the lock is in
use. Define an ia64 version of __raw_read_trylock which behaves
correctly, and drop the generic one.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
With the previous commit, we can handle arbitrary shared re-mappings
even without this complexity, and since the only known private mappings
are for strange users of /dev/mem (which never create an incomplete one),
there seems to be no reason to support it.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On most powerpc CPUs, the dcache and icache are not coherent so
between writing and executing a page, the caches must be flushed.
Userspace programs assume pages given to them by the kernel are icache
clean, so we must do this flush between the kernel clearing a page and
it being mapped into userspace for execute. We were not doing this
for hugepages, this patch corrects the situation.
We use the same lazy mechanism as we use for normal pages, delaying
the flush until userspace actually attempts to execute from the page
in question.
Tested on G5.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Patch from Deepak Saxena
This looks like a leftover from 2.4 days...
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Local add/sub macros need to have a parameter to specify
the addend/subtrahend respectively.
Signed-off-by: Christoph Lameter <clameter@sgi.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
We have a customer application which trips a bug. The problem arises
when a driver attempts to call do_munmap on an area which is mapped, but
because current->thread.task_size has been set to 0xC0000000, the call
to do_munmap fails thinking it is an unmap beyond the user's address
space.
The comment in fs/binfmt_elf.c in load_elf_library() before the call
to SET_PERSONALITY() indicates that task_size must not be changed for
the running application until flush_thread, but is for ia64 executing
ia32 binaries.
This patch moves the setting of task_size from SET_PERSONALITY() to
flush_thread() as indicated. The customer application no longer is able
to trip the bug.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Altix only patch to add fixup code that sets up
pci_controller->window. This code is a temporary
fix until ACPI support on Altix is added.
Also, corrects the usage of pci_dev->sysdata,
which had previously been used to reference
platform specific device info, to now point to
a pci_controller struct.
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
