the 'load_irix_binary' and having kernel faults, Irix support is
disabled. I suspect locking of some sort, but I will now have to
investigate further.
Static IRIX binaries are now being detected properly and are using the
ELF interpreter found in this file.
Signed-off-by: Steven J. Hill <sjhill@realitydiluted.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
binutils are broken and don't warn about this use of $at even though
gas is in .set noat mode so this for now is an accident waiting to
happen.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patch from Kenneth Tan
Defining IXP46X peripheral devices memory mapping definitions that have
been missed out:
o Peripheral virtual base address is being adjusted to allow more headroom to add extra peripheral device addresses
o Peripheral size is being increased to address the above needs
o Virtual address of expansion bus and PCI configuration register needs to be adjusted as new peripheral device memory space is overlapping with their virtual address space
Signed-off-by: Kenneth Tan <chong.yin.tan@intel.com>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Introduce ixp2000_reg_wrb, which is a variant of ixp2000_reg_write
that does a readback from the target register, to make sure that
the write has been flushed out of the write buffer.
Unlike the previous (ineffective) readback in ixp2000_reg_write, this
readback is followed by an instruction that depends on the value of
the readback so that the CPU actually stalls until the readback has
completed.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Turn ixp2000_reg_read into an inline function.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
The workaround that we do for avoiding triggering ixp2400 erratum #66
involves mapping I/O pages using XCB=101 instead of XCB=000 so that we
prevent the I/O signal to the gasket from being asserted (which can
cause data corruption.) But XCB=101 mappings are write-buffered while
mappings using XCB=000 are not, which is why if we use XCB=101 mappings
we do a readback for every CSR store in an attempt to make sure that
the store has been pushed out of the xscale core and the gasket.
Unfortunately, there are two issues with this:
- we do a readback for every CSR store, which is wrong, because the
register we are writing to might have unwanted side-effects on read,
for example, in the case of the scratchpad ring enqueue/dequeue
registers; and
- the readback is totally ineffective in the way we currently do it,
because we just issue a load but do not issue any instruction that
depends on the return value of that load, so the xscale core does
not wait for the load to complete before continuing.
See this linux-arm-kernel mailing list post for further information:
http://lists.arm.linux.org.uk/pipermail/linux-arm-kernel/2005-September/031314.html
This means that my ixp2400 boxes have been running for many months
without a working readback in ixp2000_reg_write, without any apparent
adverse effects. Two of them have been running for a week now with
the actual readback deleted from ixp2000_reg_write, also without any
apparent ill effects.
So, because in its current form it does more harm than good, the
readback in ixp2000_reg_write should simply be killed, as the patch
below does.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Macro arguments should _always_ be surrounded by parentheses
when used to prevent unexpected problems with operator precedence.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since the machine information structures are now static, the
compiler might optimise them away. Mark them with
__attribute_used__ to prevent this occuring.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Expose faster ether compare for use by protocols and other
driver. And change name to be more consistent with other ether
address manipulation routines in same file
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
With CONFIG_PM=n:
drivers/built-in.o(.text+0x1098c): In function `hub_thread':
drivers/usb/core/hub.c:2673: undefined reference to `.dpm_runtime_resume'
drivers/built-in.o(.text+0x10998):drivers/usb/core/hub.c:2674: undefined reference to `.dpm_runtime_resume'
Please, never ever ever put extern decls into .c files. Use the darn header
files :(
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as592) makes a few small improvements to the way device
strings are handled, and it fixes some bugs in a couple of other sysfs
attribute routines. (Look at show_configuration_string() to see what I
mean.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I can't stand text lines that wrap-around in my 80-column windows. This
patch (as589) makes cosmetic changes to a couple of source files.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This revised patch (as587b) improves the implementation of USB endpoint
sysfs files. Instead of storing a whole bunch of attributes for every
single endpoint, each endpoint now gets its own kobject and they can
share a static list of attributes. The number of extra fields added to
struct usb_host_endpoint has been reduced from 4 to 1.
The bEndpointAddress field is retained even though it is redundant (it
repeats the same information as the attributes' directory name). The
code avoids calling kobject_register, to prevent generating unwanted
hotplug events.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This revised patch (as586b) makes usb-handoff permanently true and no
longer a kernel boot parameter. It also removes the piix3_usb quirk code;
that was nothing more than an early version of the USB handoff code
(written at a time when Intel's PIIX3 was about the only motherboard with
USB support). And it adds identifiers for the three PCI USB controller
classes to pci_ids.h.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This should let us get rid of all of the different hooks in the USB core for
when something has changed.
Also, some other parts of the kernel have wanted to know this kind of
information at times.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a USB device is put into suspend mode, the current drawn from VBUS
has to be less than 500 uA. Some transceivers need to be put into a
special power-saving mode to accomplish this, and won't have a separate
OTG driver handling that.
This adds a suspend method to the "otg_transceiver" struct -- misnamed,
it's not only for OTG -- and calls it from the OMAP UDC driver.
Signed-off-by: Juha Yrj?l? <juha.yrjola@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The way we're looking at USB suspend lately doesn't expect drivers to
call usb_suspend_device() or usb_resume_device() directly; that'll
be implicit when no interfaces are in use.
This patch removes those APIs from visibility outside usbcore.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
drivers/usb/core/hub.c | 12 ++++--------
drivers/usb/core/usb.h | 4 ++++
include/linux/usb.h | 5 -----
3 files changed, 8 insertions(+), 13 deletions(-)
This saves a word from "struct device" ... there's a refcounting mechanism
stub that's rather ineffective (the values are never even tested!), which
can safely be deleted. With this patch it uses normal device refcounting,
so any potential users of the pm_parent mechanism will be more correct.
(That mechanism is actually unusable for now though; it does nothing.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/base/power/main.c | 26 +++-----------------------
include/linux/pm.h | 1 -
2 files changed, 3 insertions(+), 24 deletions(-)
This patch removes the extra usb_suspend_device() parameter. The original
reason to pass that parameter was so that this routine could suspend any
active children. A previous patch removed that functionality ... leaving
no reason to pass the parameter. A close analogy is pci_set_power_state,
which doesn't need a pm_message_t either.
On the internal code path that comes through the driver model, the parameter
is now used to distinguish cases where USB devices need to "freeze" but not
suspend. It also checks for an error case that's accessible through sysfs:
attempting to suspend a device before its interfaces (or for hubs, ports).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/core/hub.c | 34 +++++++++++++++++++++-------------
drivers/usb/core/usb.c | 23 +++++++++++++++++++++--
drivers/usb/host/ehci-hcd.c | 2 +-
drivers/usb/host/isp116x-hcd.c | 2 +-
drivers/usb/host/ohci-pci.c | 2 +-
include/linux/usb.h | 2 +-
6 files changed, 46 insertions(+), 19 deletions(-)
This patch adds endpoint information for both devices and interfaces to
sysfs. Previously it was only possible to get the endpoint information
from usbfs, and never possible to get any information on endpoint 0.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/core/sysfs.c | 195 ++++++++++++++++++++++++++++++++++++++++++++++-
include/linux/usb.h | 4
2 files changed, 197 insertions(+), 2 deletions(-)
I told you that the pci_ids.h cleanup was a bad idea ;)
Cc: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pci_ids.h cleanup: remove duplicated entries and change some defines to
explicit value rather than in terms of another constant, preparation for
removing unused symbols
Signed-off-by: Grant Coady <gcoady@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
include/linux/pci_ids.h | 28 +++++++++-------------------
1 file changed, 9 insertions(+), 19 deletions(-)
Some PCI adapters (eg. ipr scsi adapters) have an exposure today in that they
issue BIST to the adapter to reset the card. If, during the time it takes to
complete BIST, userspace attempts to access PCI config space, the host bus
bridge will master abort the access since the ipr adapter does not respond on
the PCI bus for a brief period of time when running BIST. On PPC64 hardware,
this master abort results in the host PCI bridge isolating that PCI device
from the rest of the system, making the device unusable until Linux is
rebooted. This patch is an attempt to close that exposure by introducing some
blocking code in the PCI code. When blocked, writes will be humored and reads
will return the cached value. Ben Herrenschmidt has also mentioned that he
plans to use this in PPC power management.
Signed-off-by: Brian King <brking@us.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/pci/access.c | 89 ++++++++++++++++++++++++++++++++++++++++++++++++
drivers/pci/pci-sysfs.c | 20 +++++-----
drivers/pci/pci.h | 7 +++
drivers/pci/proc.c | 28 +++++++--------
drivers/pci/syscall.c | 14 +++----
include/linux/pci.h | 7 +++
6 files changed, 134 insertions(+), 31 deletions(-)
Rename SCTP specific control message flags to use SCTP_ prefix rather than
MSG_ prefix as per the latest sctp sockets API draft.
Signed-off-by: Ivan Skytte Jorgensen <isj-sctp@i1.dk>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
The new SMBus PEC implementation doesn't support PEC emulation on
non-PEC non-I2C SMBus masters, so we can drop all related code.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is my rewrite of the SMBus PEC support. The original
implementation was known to have bugs (credits go to Hideki Iwamoto
for reporting many of them recently), and was incomplete due to a
conceptual limitation.
The rewrite affects only software PEC. Hardware PEC needs very little
code and is mostly untouched.
Technically, both implementations differ in that the original one
was emulating PEC in software by modifying the contents of an
i2c_smbus_data union (changing the transaction to a different type),
while the new one works one level lower, on i2c_msg structures (working
on message contents). Due to the definition of the i2c_smbus_data union,
not all SMBus transactions could be handled (at least not without
changing the definition of this union, which would break user-space
compatibility), and those which could had to be implemented
individually. At the opposite, adding PEC to an i2c_msg structure
can be done on any SMBus transaction with common code.
Advantages of the new implementation:
* It's about twice as small (from ~136 lines before to ~70 now, only
counting i2c-core, including blank and comment lines). The memory
used by i2c-core is down by ~640 bytes (~3.5%).
* Easier to validate, less tricky code. The code being common to all
transactions by design, the risk that a bug can stay uncovered is
lower.
* All SMBus transactions have PEC support in I2C emulation mode
(providing the non-PEC transaction is also implemented). Transactions
which have no emulation code right now will get PEC support for free
when they finally get implemented.
* Allows for code simplifications in header files and bus drivers
(patch follows).
Drawbacks (I guess there had to be at least one):
* PEC emulation for non-PEC capable non-I2C SMBus masters was dropped.
It was based on SMBus tricks and doesn't quite fit in the new design.
I don't think it's really a problem, as the benefit was certainly
not worth the additional complexity, but it's only fair that I at
least mention it.
Lastly, let's note that the new implementation does slightly affect
compatibility (both in kernel and user-space), but doesn't actually
break it. Some defines will be dropped, but the code can always be
changed in a way that will work with both the old and the new
implementations. It shouldn't be a problem as there doesn't seem to be
many users of SMBus PEC to date anyway.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Discard I2C_FUNC_SMBUS_*_PEC defines. i2c clients are not supposed to
check for PEC support of i2c bus drivers on individual SMBus
transactions, and i2c bus drivers are not supposed to advertise them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drop unused i2c-over-parallel-port i2c IDs:
* I2C_HW_B_LPC was never actually used as far as I could search.
* I2C_HW_B_ELV and I2C_HW_B_VELLE are no more used since the
introduction of the unified i2c-parport driver in Linux 2.6.2.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix several redefinitions of i2c IDs. i2c IDs must not be defined
outside of i2c-id.h.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Henk Vergonet <henk@god.dyndns.org>
Acked-by: Mark McClelland <mark@alpha.dyndns.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
New driver for the Xicor X1205 RTC chip.
Signed-off-by: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drop I2C_SMBUS_I2C_BLOCK_MAX, use I2C_SMBUS_BLOCK_MAX instead.
I2C_SMBUS_I2C_BLOCK_MAX has always been defined to the same value as
I2C_SMBUS_BLOCK_MAX, and this will never change: setting it to a lower
value would make no sense, setting it to a higher value would break
i2c_smbus_data compatibility. There is no point in changing
i2c_smbus_data to support larger block transactions in SMBus mode, as
no SMBus hardware supports more than 32 byte blocks. Thus, for larger
transactions, direct I2C transfers are the way to go.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are no more per-i2c-algorithm adapter max. Last time there were
was in July 1999.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Delete 2 out-of-date, colliding ioctl defines. I2C_UDELAY and
I2C_MDELAY are supposed to be used by i2c-algo-bit, but actually
aren't (and I suspect never were). Moreover, their values are the same
as I2C_FUNCS and I2C_SLAVE_FORCE, respectively, which *are* widely
used.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix a misplaced comment in i2c.h. Spotted by Hideki Iwamoto.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CVS revision IDs are totally useless and irrelevant by now.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The i2c_smbus_data union block member has a comment stating that an
extra byte is required for SMBus Block Process Call transactions. This
has been true for three weeks around June 2002, but no more since, so
it is about time that we drop this comment and fix the definition.
From: Hideki Iwamoto <h-iwamoto@kit.hi-ho.ne.jp>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
include/linux/i2c.h | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
Add complete support for 5714/5715. These chips are very similar to
5780 so the changes are very trivial. A TG3_FLG2_5780_CLASS flag is
added to identify these chips.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Attached is kernel patch for UDP Fragmentation Offload (UFO) feature.
1. This patch incorporate the review comments by Jeff Garzik.
2. Renamed USO as UFO (UDP Fragmentation Offload)
3. udp sendfile support with UFO
This patches uses scatter-gather feature of skb to generate large UDP
datagram. Below is a "how-to" on changes required in network device
driver to use the UFO interface.
UDP Fragmentation Offload (UFO) Interface:
-------------------------------------------
UFO is a feature wherein the Linux kernel network stack will offload the
IP fragmentation functionality of large UDP datagram to hardware. This
will reduce the overhead of stack in fragmenting the large UDP datagram to
MTU sized packets
1) Drivers indicate their capability of UFO using
dev->features |= NETIF_F_UFO | NETIF_F_HW_CSUM | NETIF_F_SG
NETIF_F_HW_CSUM is required for UFO over ipv6.
2) UFO packet will be submitted for transmission using driver xmit routine.
UFO packet will have a non-zero value for
"skb_shinfo(skb)->ufo_size"
skb_shinfo(skb)->ufo_size will indicate the length of data part in each IP
fragment going out of the adapter after IP fragmentation by hardware.
skb->data will contain MAC/IP/UDP header and skb_shinfo(skb)->frags[]
contains the data payload. The skb->ip_summed will be set to CHECKSUM_HW
indicating that hardware has to do checksum calculation. Hardware should
compute the UDP checksum of complete datagram and also ip header checksum of
each fragmented IP packet.
For IPV6 the UFO provides the fragment identification-id in
skb_shinfo(skb)->ip6_frag_id. The adapter should use this ID for generating
IPv6 fragments.
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (forwarded)
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch moves rfcomm_crc_table[] into the RFCOMM core, because there
is no need to keep it in a separate file.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In PM v1, all devices were called at SUSPEND_DISABLE level. Then
all devices were called at SUSPEND_SAVE_STATE level, and finally
SUSPEND_POWER_DOWN level. However, with PM v2, to maintain
compatibility for platform devices, I arranged for the PM v2
suspend/resume callbacks to call the old PM v1 suspend/resume
callbacks three times with each level in order so that existing
drivers continued to work.
Since this is obsolete infrastructure which is no longer necessary,
we can remove it. Here's an (untested) patch to do exactly that.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch allows struct class_device to be nested, so that another
struct class_device can be the parent of a new one, instead of only
having the struct class be the parent. This will allow us to
(hopefully) fix up the input and video class subsystem mess.
But please people, don't go crazy and start making huge trees of class
devices, you should only need 2 levels deep to get everything to work
(remember to use a class_interface to get notification of a new class
device being added to the system.)
Oh, this also allows us to have the possibility of potentially, someday,
moving /sys/block into /sys/class. The main hindrance is that pesky
/dev numberspace issue...
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A "coldplug + udevstart" can be simple like this:
for i in /sys/block/*/*/uevent; do echo 1 > $i; done
for i in /sys/class/*/*/uevent; do echo 1 > $i; done
for i in /sys/bus/*/devices/*/uevent; do echo 1 > $i; done
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Driver core: pass interface to class intreface methods
Pass interface as argument to add() and remove() class interface
methods. This way a subsystem can implement generic add/remove
handlers and then call interface-specific ones.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I2O: cleanup - remove i2o_device_class
I2O devices reside on their own bus so there should be no reason
to also have i2c_device class that mirros i2o bus.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a refresh of an earlier patch to add "wakeup" support to the
PM core model. This provides per-device bus-neutral control of the
use of wakeup events.
* "struct device_pm_info" has two bits that are initialized as
part of setting up the enclosing struct device:
- "can_wakeup", reflecting hardware capabilities
- "may_wakeup", the policy setting (when CONFIG_PM)
* There's a writeable sysfs "wakeup" file, with one of two values:
- "enabled", when the policy is to allow wakeup
- "disabled", when the policy is not to allow it
- "" if the device can't currently issue wakeups
By default, wakeup is enabled on all devices that support it. If its
driver doesn't support it ... treat it as a bug. :)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch from Bellido Nicolas
The AAEC-2000 has an ARM PrimeCell PL110 Color LCD Controller.
This patch contains the platform glue that will be used by specific boards.
Signed-off-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Bellido Nicolas
This adds platform code for MTD devices on AAEC-2000.
Signed-off-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Bellido Nicolas
linux/config.h is not necessary in hardware.h, while asm/sizes.h and asm/arch//aaec2000.h will be used later.
Signed-off-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Bellido Nicolas
The AAED-2000 board has GPIO pins on an external port.
This patch adds the defines, and do the necessary mapping.
Signed-off-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Bellido Nicolas
Add defines for GPIO registers on the AAEC-2000 processor.
Signed-off-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
This is the PXA2xx common IRDA driver, plus platform support
for Lubbock and Mainstone.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Acked-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Erik Hovland
I noticed that the same typo (i before c in associated) showed up twice
in the file kernel/include/linux/mmc/mmc.h.
This patch fixes both of the instances I found with this mistake. The
typos are in comments and should have no affect on working code.
E
Signed-off-by: Erik Hovland <erik@hovland.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Todd Poynor
Add symbols for PXA2xx PWRMODE register M field that selects low-power
mode, replace unadorned constants. Honor power mode parameter of
pxa_cpu_suspend(mode), no longer force to 3 (sleep). Full Deep Sleep
low-power mode support for PXA27x is pending generic PM interfaces to
select more than 2 suspend-to-RAM-style power modes, but this is
expected soon. This can be hardcoded in the meantime by replacing the
pxa_cpu_suspend() parameter value. From David Burrage and Todd Poynor.
Try #2 removes one of the register copies and moves the code to save the
pxa_cpu_suspend parameter to immediately surround the call that requires
the parameter value be preserved.
Signed-off-by: Todd Poynor <tpoynor@mvista.com>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Jon Ringle
Updated 2898/1 per comments:
- Removed fixup
- Moved code in mach-mp1000/ to mach-clps711x/
- Cleaned up code in mp1000-seprom.c. Eliminated code that displayed the contents of the eeprom
Please comment.
Signed-off-by: Jon Ringle
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
... and related annotations for amd64 - swiotlb code is shared, but
prototypes are not.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- ->releasepage() annotated (s/int/gfp_t), instances updated
- missing gfp_t in fs/* added
- fixed misannotation from the original sweep caught by bitwise checks:
XFS used __nocast both for gfp_t and for flags used by XFS allocator.
The latter left with unsigned int __nocast; we might want to add a
different type for those but for now let's leave them alone. That,
BTW, is a case when __nocast use had been actively confusing - it had
been used in the same code for two different and similar types, with
no way to catch misuses. Switch of gfp_t to bitwise had caught that
immediately...
One tricky bit is left alone to be dealt with later - mapping->flags is
a mix of gfp_t and error indications. Left alone for now.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Beginning of gfp_t annotations:
- -Wbitwise added to CHECKFLAGS
- old __bitwise renamed to __bitwise__
- __bitwise defined to either __bitwise__ or nothing, depending on
__CHECK_ENDIAN__ being defined
- gfp_t switched from __nocast to __bitwise__
- force cast to gfp_t added to __GFP_... constants
- new helper - gfp_zone(); extracts zone bits out of gfp_t value and casts
the result to int
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Ben Dooks
Change set_s3c2410fb_info to s3c2410_fb_set_platdata
and use kmalloc() for the copy of the information it
is passed.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
We already had a mapping for the msf, but we didn't have any
register definitions for it yet.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ian Campbell
The sparse warning initially surfaced in sound/arm/pxa2xx-ac97.c
because it was using u32 * variables to hold the unsigned long *
register addresses.
I submitted an ALSA patch for this http://thread.gmane.org/gmane.linux.alsa.devel/27804 issue and it was suggested that it might be preferable to change the register
definitions to use u32.
Most other subarches seem to use u32 for their register type, at least
the ones which use a __REG macro (like the PXA) do. Nico indicated in
the thread above that he wouldn't mind this patch.
Changing the type required fixes for opposite warnings in the pxa2xx usb
gadget code but that was the only new warning introduced on defconfig
or lubbock, mainstone and our own PXA255 boards.
Signed-off-by: Ian Campbell <icampbell@arcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add generic values for the parameters to the
s3c2410_gpio_cfgpin() function, so that a caller
does not need to know the exact constant for
the specified pin.
This is very useful for the case where a driver
is passed a gpio pin number and needs to reconfigure
the pin's function.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
Convert map_desc.physical to map_desc.pfn. This allows us to add
support for 36-bit addressed physical devices in the static maps
without having to resort to u64 variables.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix sparse warnings in arch/arm/kernel/module.c,
arch/arm/mm/consistent.c, drivers/pcmcia/sa1111_generic.c,
and platform support files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
EBSA110 only requires hardware.h to be included for a couple of
files. Move the include there.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Including asm/hardware.h into asm/io.h can cause #define clashes
between platform specific definitions and driver local definitions.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- 100msec sleep is a little excessive, lots of requests can complete
in that timeframe. Use 10msec instead.
- Rename QUEUE_FLAG_BYPASS to QUEUE_FLAG_ELVSWITCH to indicate what
is going on.
Signed-off-by: Jens Axboe <axboe@suse.de>
This patch reimplements elevator switch. This patch assumes generic
dispatch queue patchset is applied.
* Each request is tagged with REQ_ELVPRIV flag if it has its elevator
private data set.
* Requests which doesn't have REQ_ELVPRIV flag set never enter
iosched. They are always directly back inserted to dispatch queue.
Of course, elevator_put_req_fn is called only for requests which
have its REQ_ELVPRIV set.
* Request queue maintains the current number of requests which have
its elevator data set (elevator_set_req_fn called) in
q->rq->elvpriv.
* If a request queue has QUEUE_FLAG_BYPASS set, elevator private data
is not allocated for new requests.
To switch to another iosched, we set QUEUE_FLAG_BYPASS and wait until
elvpriv goes to zero; then, we attach the new iosched and clears
QUEUE_FLAG_BYPASS. New implementation is much simpler and main code
paths are less cluttered, IMHO.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
This patch kills max_back_kb handling from elv_dispatch_sort() and
kills max_back_kb field from struct request_queue.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
Currently, both generic elevator code and specific ioscheds
participate in the management and usage of last_merge. This
and the following patches move last_merge handling into
generic elevator code.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
Implements generic dispatch queue which can replace all
dispatch queues implemented by each iosched. This reduces
code duplication, eases enforcing semantics over dispatch
queue, and simplifies specific ioscheds.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
struct gendisk has these two fields: stamp, stamp_idle. Update to
stamp_idle is always in sync with stamp and they are always the same.
Therefore, it does not add any value in having two fields tracking
same timestamp. Suggest to remove it.
Also, we should only update gendisk stats with non-zero value.
Advantage is that we don't have to needlessly calculate memory address,
and then add zero to the content.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
Optimise attribute revalidation when hardlinking. Add post-op attributes
for the directory and the original inode.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
"Optional" means that the close call will not fail if the getattr
at the end of the compound fails.
If it does succeed, try to refresh inode attributes.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Since the directory attributes change every time we CREATE a file,
we might as well pick up the new directory attributes in the same
compound.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Since we almost always call nfs_end_data_update() after we called
nfs_refresh_inode(), we now end up marking the inode metadata
as needing revalidation immediately after having updated it.
This patch rearranges things so that we mark the inode as needing
revalidation _before_ we call nfs_refresh_inode() on those operations
that need it.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Allow nfs_refresh_inode() also to update attributes on the inode if the
RPC call was sent after the last call to nfs_update_inode().
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Commit id 6142891a0c
Andi Kleen reports that it seems to break things for some people,
and since it's purely a small optimization, revert it for now.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
flush_tlb_all() can be a scaling issue on large SGI Altix systems
since it uses the global call_lock and always executes on all cpus.
When a process enters flush_tlb_range() to purge TLBs for another
process, it is possible to avoid flush_tlb_all() and instead allow
sn2_global_tlb_purge() to purge TLBs only where necessary.
This patch modifies flush_tlb_range() so that this case can be handled
by platform TLB purge functions and updates ia64_global_tlb_purge()
accordingly. sn2_global_tlb_purge() now calculates the region register
value from the mm argument introduced with this patch.
Signed-off-by: Dean Roe <roe@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Patch from Ian Campbell
Sparse complains about the definition of generic_fls in asm-arm/bitops.h:
CHECK /home/icampbell/devel/kernel/2.6/arch/arm/mach-pxa/viper.c
include2/asm/bitops.h:350:34: error: marked inline, but without a definition
The definition is unnecessary since linux/bitops.h defines generic_fls before including asm/bitops.h and asm/bitops.h should not be included directly. There are still some places where asm/bitops.h is directly included, but I think that code should be fixed. I was a little wary of the patch for this reason but lubbock, mainstone and assabet all build OK and so do my in house boards...
ARM is the only arch with the generic_fls prototype in this way.
Signed-off-by: Ian Campbell <icampbell@arcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add kernel-doc to skbuff.h, skbuff.c to eliminate kernel-doc warnings.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Now that we've switched over to storing MTUs in the xfrm_dst entries,
we no longer need the dst's get_mss methods. This patch gets rid of
them.
It also documents the fact that our MTU calculation is not optimal
for ESP.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch addresses a few issues with the open/close protocol that
were revealed by the newly added disengage functionality combined
with more extensive testing.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The MAD layer was violating the DMA API by touching data buffers used
for sends after the DMA mapping was done. This causes problems on
non-cache-coherent architectures, because the device doing DMA won't
see updates to the payload buffers that exist only in the CPU cache.
Fix this by having all MAD consumers use ib_create_send_mad() to
allocate their send buffers, and moving the DMA mapping into the MAD
layer so it can be done just before calling send (and after any
modifications of the send buffer by the MAD layer).
Tested on a non-cache-coherent PowerPC 440SPe system.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
My alpha build is exploding because asm/atomic.h now needs smb_mb(), which is
over in the (not included) system.h.
I fear what will happen if I include system.h into atomic.h, so let's put the
barriers into their own header file.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the new ID 0x132a and configure the new PCI Diva console port. This
device supports only 1 single console UART.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested by Wolfgang Denk with this device:
00:0f.0 Network controller: PLX Technology, Inc. PCI <-> IOBus Bridge (rev 01)
Subsystem: Exsys EX-4055 4S(16C550) RS-232
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
Region 0: Memory at 80100000 (32-bit, non-prefetchable) [size=128]
Region 1: I/O ports at 7080 [size=128]
Region 2: I/O ports at 7400 [size=32]
00:0f.0 Class 0280: 10b5:9050 (rev 01)
Subsystem: d84d:4055
Results with this patch:
Serial: 8250/16550 driver $Revision: 1.90 $ 32 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
PCI: Found IRQ 10 for device 0000:00:0f.0
ttyS4 at I/O 0x7400 (irq = 10) is a 16550A
ttyS5 at I/O 0x7408 (irq = 10) is a 16550A
ttyS6 at I/O 0x7410 (irq = 10) is a 16550A
ttyS7 at I/O 0x7418 (irq = 10) is a 16550A
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix a bug which was reported and diagnosed by
Stefan Jones <stefan.jones@churchillrandoms.co.uk>
IDR trees include a cache of idr_layer objects. There's no way to destroy
this cache, so when we discard an overall idr tree we end up leaking some
memory.
Add and use idr_destroy() for this. v9fs and infiniband also need to use
idr_destroy() to avoid leaks.
Or, we make the cache global, like radix_tree_preload(). Which is probably
better. Later.
Cc: Eric Van Hensbergen <ericvh@ericvh.myip.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Robert Love <rml@novell.com>
Cc: John McCutchan <ttb@tentacle.dhs.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As stated in Documentation/atomic_ops.txt, atomic functions
returning values must have the memory barriers both before and after
the operation.
Thanks to DaveM for pointing that out.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On architectures where the char type defaults to unsigned some of the
arithmetic in the AX.25 stack to fail, resulting in some packets being dropped
on receive.
Credits for tracking this down and the original patch to
Bob Brose N0QBJ <linuxhams@n0qbj-11.ampr.org>.
Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Update drivers to new input layer changes.
Signed-off-by: Helge Deller <deller@parisc-linux.org>
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Reorder code in gscps2_interrupt() and only enable ports when opened.
This fixes issues with hangs booting an SMP kernel on my C360.
Previously serio_interrupt() could be called before the lock in
struct serio was initialised.
Signed-off-by: Richard Hirst <rhirst@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
fixup.S needs to specify .level and use correct LDREG macro.
New binutils has a bug where it doesn't "promote" from PA1.0 to PA1.1
correctly when using ",s" completer.
remove use of __LP64__ in assembly.h and add some white space.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
drivers/infiniband depends on definition of pgprot_noncached() macro.
Someone else will have to fix it's wrong.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
add ECANCELED - SuSv3 wants one L. IB/SDP actually returns this error.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fix the alloc_slabmgmt panic
Hopefully this should also fix a lot of other intermittent kernel bugs.
The problem has been around since 2.6.9-rc2-pa6 when we allowed
floating point registers to be used in kernel code. The essence of
the problem is that gcc prefers to use floating point for integer
divides and multiples. Further, it can rely on the values in the no
clobber fp regs being correct across a function call. Unfortunately,
our task switch function only saves the integer no clobber registers,
not the fp ones, so if gcc makes a function call to any function in
the kernel which could sleep, the values it is relying on in any no
clobber floating point register may be lost. In the case of
alloc_slabmgmt, the value of the page offset is being stored in %fr12
across a call to kmem_getpages(), which sleeps if no pages are
available. Thus, the offset can be trashed and the slab code can end
up with a completely bogus address leading to corruption.
Kudos to Randolph who came up with the program to trip this problem at
will and thus allowed it to be tracked and fixed.
Signed-off-by: James Bottomley <jejb@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
2.6.12-rc1-pa6 use work queue in LED/LCD driver instead of tasklet.
Main advantage is it allows use of msleep() in the led_LCD_driver to
"atomically" perform two MMIO writes (CMD, then DATA).
Lead to nice cleanup of the main led_work_func() and led_LCD_driver().
Kudos to David for being persistent.
From: David Pye <dmp@davidmpye.dyndns.org>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Optimize ext2_find_next_zero_bit. Gives about 25% perf improvement with a
rsync test with ext3.
Signed-off-by: Randolph Chung <tausq@parisc-linux.org>
fix ext3 performance - ext2_find_next_zero() was culprit.
Kudos to jejb for pointing out the the possibility that ext2_test_bit
and ext2_find_next_zero() may in fact not be enumerating bits in
the bitmap because of endianess. Took sparc64 implementation and
adapted it to our tree. I suspect the real problem is ffz() wants
an unsigned long and was getting garbage in the top half of the
unsigned int. Not confirmed but that's what I suspect.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Fix find_next_bit for 32-bit
Make masking consistent for bitops
From: Joel Soete <soete.joel@tiscali.be>
Signed-off-by: Randolph Chung <tausq@parisc-linux.org>
Add back incorrectly removed ext2_find_first_zero_bit definition
Signed-off-by: James Bottomley <jejb@parisc-linux.org>
Fixup bitops.h to use volatile for *_bit() ops
Based on this email thread:
http://marc.theaimsgroup.com/?t=108826637900003
In a nutshell:
*_bit() want use of volatile.
__*_bit() are "relaxed" and don't use spinlock or volatile.
other minor changes:
o replaces hweight64() macro with alias to generic_hweight64() (Joel Soete)
o cleanup ext2* macros so (a) it's obvious what the XOR magic is about
and (b) one version that works for both 32/64-bit.
o replace 2 uses of CONFIG_64BIT with __LP64__. bitops.h used both.
I think header files that might go to user space should use
something userspace will know about (__LP64__).
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Move SHIFT_PER_LONG to standard location for BITS_PER_LONG (asm/types.h)
and ditch the second definition of BITS_PER_LONG in bitops.h
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
export profile_pc() symbol - oprofile needs it when built as a module.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Take into account nullified insn and lock functions for profiling
This is needed at the end of functions; it is typical that the return
branch nullifies the next insn, which is in the next function. This
causes profiling data to show up against the "wrong" function.
We also count lock times against the locker. This is consistent with
other architectures.
Signed-off-by: Randolph Chung <tausq@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Neaten up the CONFIG_PA20 ifdefs
More merge fixes, this time for SMP
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Prettify the CONFIG_DEBUG_SPINLOCK __SPIN_LOCK_UNLOCKED initializers.
Clean up some warnings with CONFIG_DEBUG_SPINLOCK enabled.
Fix build with spinlock debugging turned on. Patch is cleaner like this,
too.
Remove mandatory 16-byte alignment requirement on PA2.0 processors by
using the ldcw,CO completer. Provides a nice insn savings.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
move pa_tlb_lock and it's primary consumers to tlb_flush.h
Future step will be to move spinlock_t definition out of system.h.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
2.6.12-rc4-pa3 : first pass at making sure use of RFI conforms to
PA 2.0 arch pages F-4 and F-5, PA 1.1 Arch page 3-19 and 3-20.
The discussion revolves around all the rules for clearing PSW Q-bit.
The hard part is meeting all the rules for "relied upon translation".
.align directive is used to guarantee the critical sequence ends more than
8 instructions (32 bytes) from the end of page.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Convert pa_dev->hpa from an unsigned long to a struct resource.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Fix up users of ->hpa to use ->hpa.start instead.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fix parse_tree_node. much more needs to be done to fix this file.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Make drivers.c compile based on a patch from Pat Mochel.
From: Patrick Mochel <mochel@digitalimplant.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fix drivers.c to create new device tree nodes when no match is found.
Signed-off-by: Richard Hirst <rhirst@parisc-linux.org>
Do a proper depth-first search returning parents before children, using the
new klist infrastructure.
Signed-off-by: Richard Hirst <rhirst@parisc-linux.org>
Fixed parisc_device traversal so that pdc_stable works again
Fixed check_dev so it doesn't dereference a parisc_device until it
has verified the bus type
Signed-off-by: Randolph Chung <tausq@parisc-linux.org>
Convert pa_dev->hpa from an unsigned long to a struct resource.
Use insert_resource() instead of request_mem_region().
Request resources at bus walk time instead of driver probe time.
Don't release the resources as we don't have any hotplug parisc_device
support yet.
Add parisc_pathname() to conveniently get the textual representation
of the hwpath used in sysfs.
Inline the remnants of claim_device() into its caller.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
I noticed that some of the STI regions weren't showing up in iomem.
Reading the STI spec indicated that all STI devices occupy at least 32MB.
So check for STI HPAs and give them 32MB instead of 4kB.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
This is needed for full AMD and VIA drivers and possibly more. Functions
to turn actual clocking and cycle timings into register values. Also to
merge shared timings to compute an optimal timing set.
Built from the drivers/ide version by Vojtech Pavlik
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Patch from Ben Dooks
From: Guillaume Gourat <guillaume.gourat@nexvision.fr>
Add MASK definitions for DCLK0 and DCLK1
Signed-off-by: Guillaume Gourat <guillaume.gourat@nexvision.fr>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Avoid the possiblity that if the board is using
a 16.9334 or higher crystal with a high PLL
multiplier, then the pll value could overflow
the capability of an int.
Also fix the value types of the intermediate
variables to unsigned int.
Rewrite of patch from Guillaume Gourat
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This reverts commit 3359b54c8c and
replaces it with a cleaner version that is purely based on page table
operations, so that the synchronization between inode size and hugetlb
mappings becomes moot.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This introduces a limit parameter to the core bootmem allocator; The new
parameter indicates that physical memory allocated by the bootmem
allocator should be within the requested limit.
We also introduce alloc_bootmem_low_pages_limit, alloc_bootmem_node_limit,
alloc_bootmem_low_pages_node_limit apis, but alloc_bootmem_low_pages_limit
is the only api used for swiotlb.
The existing alloc_bootmem_low_pages() api could instead have been
changed and made to pass right limit to the core allocator. But that
would make the patch more intrusive for 2.6.14, as other arches use
alloc_bootmem_low_pages(). We may be done that post 2.6.14 as a
cleanup.
With this, swiotlb gets memory within 4G for both x86_64 and ia64
arches.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Ravikiran G Thirumalai <kiran@scalex86.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The hugetlb pages are currently pre-faulted. At the time of mmap of
hugepages, we populate the new PTEs. It is possible that HW has already
cached some of the unused PTEs internally. These stale entries never
get a chance to be purged in existing control flow.
This patch extends the check in page fault code for hugepages. Check if
a faulted address falls with in size for the hugetlb file backing it.
We return VM_FAULT_MINOR for these cases (assuming that the arch
specific page-faulting code purges the stale entry for the archs that
need it).
Signed-off-by: Rohit Seth <rohit.seth@intel.com>
[ This is apparently arguably an ia64 port bug. But the code won't
hurt, and for now it fixes a real problem on some ia64 machines ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Not only are the qop parameters that are passed around throughout the gssapi
unused by any currently implemented mechanism, but there appears to be some
doubt as to whether they will ever be used. Let's just kill them off for now.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Add support for privacy to the krb5 rpcsec_gss mechanism.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The code this was originally derived from processed wrap and mic tokens using
the same functions. This required some contortions, and more would be required
with the addition of xdr_buf's, so it's better to separate out the two code
paths.
In preparation for adding privacy support, remove the last vestiges of the
old wrap token code.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Various xdr encode routines use au_rslack to guess where the reply argument
will end up, so we can set up the xdr_buf to recieve data into the right place
for zero copy.
Currently we calculate the au_rslack estimate when we check the verifier.
Normally this only depends on the verifier size. In the integrity case we add
a few bytes to allow for a length and sequence number.
It's a bit simpler to calculate only the verifier size when we check the
verifier, and delay the full calculation till we unwrap.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
For privacy, we need to allocate pages to store the encrypted data (passed
in pages can't be used without the risk of corrupting data in the page cache).
So we need a way to free that memory after the request has been transmitted.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Add support for privacy to generic gss-api code. This is dead code until we
have both a mechanism that supports privacy and code in the client or server
that uses it.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Make NFSv4 return the fully initialized file pointer with the
stateid that it created in the lookup w/intent.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This is needed by NFSv4 for atomicity reasons: our open command is in
fact a lookup+open, so we need to be able to propagate open context
information from lookup() into the resulting struct file's
private_data field.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Once the state_owner and lock_owner semaphores get removed, it will be
possible for other OPEN requests to reopen the same file if they have
lower sequence ids than our CLOSE call.
This patch ensures that we recheck the file state once
nfs_wait_on_sequence() has completed waiting.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Pete Popov