4 micro seconds is not enough for PBIAS if MMC regulator is
enabled from MMC regulator OFF.
Increase the delay for PBIAS to stabilize.
Wait for PBIAS and timeout if not.
Resolves MMC/SD failure on OMAP4
"Pbias Voltage is not same as LDO"
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Several boards defining mtd partitions also defined NAND_BLOCK_SIZE as
SZ_128K. Move the define to common-board-devices.h
This removes multiple defines of NAND_BLOCK_SIZE.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 407a6888f7 (OMAP4: hwmod data:
Add AESS, McPDM, bandgap, counter_32k, MMC, KBD, ISS & IPU) added the
entry for keypad, but did not enable it.
Enable the keypad in the hwmod database so it works.
Signed-off-by: Shubhrajyoti D<shubhrajyoti@ti.com>
Acked-by: Benoit Cousson<b-cousson@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Free Beagle rev gpios when they are read, so others can read them later
Signed-off-by: Tasslehoff Kjappfot <tasskjapp@gmail.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Without msecure beeing high it isn't possible to set (or start)
the RTC.
Tested with a BeagleBoard C4.
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Speaker amplifier is accidentally powered up in early TWL gpio setup. This
causes a few mA of needless battery current consumption. Without this patch
the amplifier can be shutdown only by having one active audio playback and
shutdown cycle to speaker output.
Thanks to Kalle Jokiniemi <kalle.jokiniemi@nokia.com> for noticing the issue.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Kalle Jokiniemi <kalle.jokiniemi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The V28_A domain in Nokia N900 that supplies VDD voltages to TLV320AIC34 and
TPA6130A2 should not be shutdown. This is because otherwise there will be
leak from VIO to VDD in TLV320AIC34 and this leak consumes more battery
current that is saved from keeping V28_A off. With this patch the battery
current consumption is approximately 1.5 mA lower.
Thanks to Kalle Jokiniemi <kalle.jokiniemi@nokia.com> for noticing the issue.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Kalle Jokiniemi <kalle.jokiniemi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
eMMC does not handle power off when not in sleep state,
Skip regulator disable during probe when eMMC is
not in known state - state left by bootloader.
Resolves eMMC failure on OMAP4
mmc0: error -110 whilst initialising MMC card
Signed-off-by: Balaji T K <balajitk@ti.com>
Tested-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Acked-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
introduced by: 96974a24
(omap: consolidate touch screen initialization among different boards)
ads7846 driver can use either gpio_pendown or get_pendown_state()
callback. In case of gpio_pendown, it requests the provided gpio_pendown
thus resulting in double requesting that gpio:
ads7846 spi1.0: failed to request pendown GPIO57
ads7846: probe of spi1.0 failed with error -16
Fix this by restricting the gpio request to the case of
get_pendown_state() callback is used.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP4 contains two separate instances of the padconf registers,
one in the core system config and one in the wakeup system config.
Pass in two tables to apply the correct values to each instance.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP4 has two mux instances, and the board may not have settings
for one of them. Allow the board file to pass NULL for an
instance's mux settings, which will initialize the mux instance
but skip writing board settings.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Don't PTR_ERR() a non-error pointer:
initcall omap4_l3_init+0x0/0xdc returned -544980480 after 0 usecs
initcall omap4_l3_init+0x0/0xdc returned with error code -544980480
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix below compilation warnings.
arch/arm/mach-omap2/omap_hwmod.c: In function 'omap_hwmod_for_each':
arch/arm/mach-omap2/omap_hwmod.c:1631: warning: 'ret' may be used uninitialized in this function
arch/arm/mach-omap2/mux.c: In function 'omap_mux_get_gpio':
arch/arm/mach-omap2/mux.c:917: warning: 'm' may be used uninitialized in this function
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
WARNING: arch/arm/mach-omap2/built-in.o(.text+0x11014): Section mismatch
in reference from the function cm_t3517_init_usbh() to the (unknown
reference) .init.data:(unknown)
The function cm_t3517_init_usbh() references
the (unknown reference) __initdata (unknown).
This is often because cm_t3517_init_usbh lacks a __initdata
annotation or the annotation of (unknown) is wrong.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The serial*_data should have been marked as __initdata as per
it's usage in the board files. Fix the same to remove the
section mismatch warnings caused by it.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Silesh C V <silesh@ti.com>
[tony@atomide.com: updated with additional fixes from Silesh]
Signed-off-by: Tony Lindgren <tony@atomide.com>
I got some build error like below while executing "make omap2plus_defconfig".
CC arch/arm/mach-omap2/board-2430sdp.o
arch/arm/mach-omap2/board-2430sdp.c: In function 'omap_2430sdp_init':
arch/arm/mach-omap2/board-2430sdp.c:247: error: 'GPIOF_OUT_INIT_LOW' undeclared (first use in this function)
arch/arm/mach-omap2/board-2430sdp.c:247: error: (Each undeclared identifier is reported only once
arch/arm/mach-omap2/board-2430sdp.c:247: error: for each function it appears in.)
This patch fixes the build error by include linux/gpio.h instead of mach/gpio.h.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Syed Mohammed Khasim <x0khasim@ti.com>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Cc: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* git://git.infradead.org/battery-2.6:
PXA: Use dev_pm_ops in z2_battery
ds2760_battery: Fix rated capacity of the hx4700 1800mAh battery
ds2760_battery: Fix indexing of the 4 active full EEPROM registers
power: Make test_power driver more dynamic.
bq27x00_battery: Name of cycle count property
max8903_charger: Add GENERIC_HARDIRQS as a dependency (fixes S390 build)
ARM: RX-51: Enable isp1704 power on/off
isp1704_charger: Allow board specific powering routine
gpio-charger: Add gpio_charger_resume
power_supply: Add driver for MAX8903 charger
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (57 commits)
regulator: Fix 88pm8607.c printk format warning
input: Add support for Qualcomm PMIC8XXX power key
input: Add Qualcomm pm8xxx keypad controller driver
mfd: Add omap-usbhs runtime PM support
mfd: Fix ASIC3 SD Host Controller Configuration size
mfd: Fix omap_usbhs_alloc_children error handling
mfd: Fix omap usbhs crash when rmmoding ehci or ohci
mfd: Add ASIC3 LED support
leds: Add ASIC3 LED support
mfd: Update twl4030-code maintainer e-mail address
mfd: Correct the name and bitmask for ab8500-gpadc BTempPullUp
mfd: Add manual ab8500-gpadc batt temp activation for AB8500 3.0
mfd: Provide ab8500-core enumerators for chip cuts
mfd: Check twl4030-power remove script error condition after i2cwrite
mfd: Fix twl6030 irq definitions
mfd: Add phoenix lite (twl6025) support to twl6030
mfd: Avoid to use constraint name in 88pm860x regulator driver
mfd: Remove checking on max8925 regulator[0]
mfd: Remove unused parameter from 88pm860x API
mfd: Avoid to allocate 88pm860x static platform data
...
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (33 commits)
OMAP3: PM: Boot message is not an error, and not helpful, remove it
OMAP3: cpuidle: change the power domains modes determination logic
OMAP3: cpuidle: code rework for improved readability
OMAP3: cpuidle: re-organize the C-states data
OMAP3: clean-up mach specific cpuidle data structures
OMAP3 cpuidle: remove useless SDP specific timings
usb: otg: OMAP4430: Powerdown the internal PHY when USB is disabled
usb: otg: OMAP4430: Fixing the omap4430_phy_init function
usb: musb: am35x: fix compile error when building am35x
usb: musb: OMAP4430: Power down the PHY during board init
omap: drop board-igep0030.c
omap: igep0020: add support for IGEP3
omap: igep0020: minor refactoring
omap: igep0020: name refactoring for future merge with IGEP3
omap: Remove support for omap2evm
arm: omap2plus: GPIO cleanup
omap: musb: introduce default board config
omap: move detection of NAND CS to common-board-devices
omap: use common initialization for PMIC i2c bus
omap: consolidate touch screen initialization among different boards
...
Modifying the macro name Main_Ref to all caps(MAIN_REF).
Suggested by Nishanth Menon <nm@ti.com>
Signed-off-by: Lesly A M <leslyam@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: David Derrick <dderrick@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (137 commits)
ARM: bcmring: convert to use sp804 clockevents
ARM: bcmring: convert to sp804 clocksource
ARM: 6912/1: bcmring: Add clkdev table in init_early
clockevents: ARM sp804: obtain sp804 timer rate via clks
clockevents: ARM sp804: allow clockevent name to be specified
clocksource: ARM sp804: obtain sp804 timer rate via clks
clocksource: ARM sp804: allow clocksource name to be specified
clocksource: convert OMAP1 to 32-bit down counting clocksource
clocksource: convert MXS timrotv2 to 32-bit down counting clocksource
clocksource: convert SPEAr platforms 16-bit up counting clocksource
clocksource: convert Integrator/AP 16-bit down counting clocksource
clocksource: convert W90x900 24-bit down counting clocksource
clocksource: convert ARM 32-bit down counting clocksources
clocksource: convert ARM 32-bit up counting clocksources
clocksource: add common mmio clocksource
ARM: update sa1100 to reflect PXA updates
ARM: omap1: convert to using readl/writel instead of volatile struct
ARM: omap1: delete useless interrupt handler
ARM: s5p: consolidate selection of timer register
ARM: 6939/1: fix missing 'cpu_relax()' declaration
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
b43: fix comment typo reqest -> request
Haavard Skinnemoen has left Atmel
cris: typo in mach-fs Makefile
Kconfig: fix copy/paste-ism for dell-wmi-aio driver
doc: timers-howto: fix a typo ("unsgined")
perf: Only include annotate.h once in tools/perf/util/ui/browsers/annotate.c
md, raid5: Fix spelling error in comment ('Ofcourse' --> 'Of course').
treewide: fix a few typos in comments
regulator: change debug statement be consistent with the style of the rest
Revert "arm: mach-u300/gpio: Fix mem_region resource size miscalculations"
audit: acquire creds selectively to reduce atomic op overhead
rtlwifi: don't touch with treewide double semicolon removal
treewide: cleanup continuations and remove logging message whitespace
ath9k_hw: don't touch with treewide double semicolon removal
include/linux/leds-regulator.h: fix syntax in example code
tty: fix typo in descripton of tty_termios_encode_baud_rate
xtensa: remove obsolete BKL kernel option from defconfig
m68k: fix comment typo 'occcured'
arch:Kconfig.locks Remove unused config option.
treewide: remove extra semicolons
...
Rather than having each platform class provide a mach/smp.h header for
smp_cross_call(), arrange for them to register the function with the
core ARM SMP code instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It shows up on the console despite using "silent" in the bootargs, and
it's really just noise in the boot log since PM init is always called.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Cc: jhnikula@gmail.com
[khilman@ti.com: minor changelog edits]
Signed-off-by: Kevin Hilman <khilman@ti.com>
The achievable power modes of the power domains in cpuidle
depends on the system wide 'enable_off_mode' knob in debugfs.
Upon changing enable_off_mode, do not change the C-states
'valid' field but instead dynamically restrict the power modes
when entering idle.
The C-states 'valid' field is just used to enable/disable some
C-states at init and shall not be changed later on.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
- fix single and multi-lines comments format
- removed the omap3_idle_bm_check function and replaced the test
in omap3_enter_idle_bm by the equivalent code
- re-organize omap3_enter_idle_bm code path, assign local variables
only when needed
- reword some comments
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The current implementation defines an internal structure and a
C-states array. Using those structures is redundant to the
structs used by the cpuidle framework.
This patch provides a clean-up of the internal struct, removes the
internal C-states array, stores the data using the existing cpuidle
per C-state struct and registers the mach specific data to cpuidle
C-state driver_data (accessed using cpuidle_[gs]et_statedata).
Also removes unused macros, fields and code and compacts the repeating
code using an inline helper function.
The result is more compact and more readable code as well as
reduced data RAM usage.
Also retain C1 as the only always valid C-state and system safe state.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
- sleep_latency and wake_latency are not used, replace them by
exit_latency which is used by cpuidle. exit_latency simply is
the sum of sleep_latency and wake_latency,
- replace threshold by target_residency,
- changed the OMAP3 specific cpuidle code accordingly,
- changed the OMAP3 board code accordingly.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The cpuidle states settings can be overriden by some board-
specific settings, by calling omap3_pm_init_cpuidle.
Remove the 3430SDP specific states settings registration
since the figures are identical to the default ones (in cpuidle34xx.c).
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Powerdown the internal UTMI PHY when USB is not enabled. This will
allow the OMAP core domain to transition to retention and offmode.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
omap4430_phy_init() function can be called with no device pointer,
to powerdown the PHY during board init when USB is disabled.
Fix the function accordingly.
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Powerdown the internal PHY during board init for OMAP44xx.
So that when musb is disabled core transition to retention/off
is not blocked.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
* power-domains:
PM: Fix build issue in clock_ops.c for CONFIG_PM_RUNTIME unset
PM: Revert "driver core: platform_bus: allow runtime override of dev_pm_ops"
OMAP1 / PM: Use generic clock manipulation routines for runtime PM
PM / Runtime: Generic clock manipulation rountines for runtime PM (v6)
PM / Runtime: Add subsystem data field to struct dev_pm_info
OMAP2+ / PM: move runtime PM implementation to use device power domains
PM / Platform: Use generic runtime PM callbacks directly
shmobile: Use power domains for platform runtime PM
PM: Export platform bus type's default PM callbacks
PM: Make power domain callbacks take precedence over subsystem ones
Add IGEP3 machine support to board-igep0020
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
to allow easy addition of IGEP3
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
IGEP2 and IGEP3 boards are very similar and can be merged into one file.
Start refactoring with changing igep2 to igep where applicable.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use generic irq chip for omap2 & 3.
Note that this patch also leaves out the spurious IRQ warning
for omap3.
This warning should no longer be needed as the interrupt handlers
for various devices have implemented the necessayr read-back of
the posted write.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The debug l3_ick/rate is not displaying the actual rate of the clock in
hardware. This is because, the core dpll set_rate function doesn't update the
clk.rate. After fixing, the l3_ick/rate is displaying proper values.
Signed-off-by: Shweta Gulati <shweta.gulati@ti.com>
Signed-off-by: Avinash.H.M <avinashhm@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Wamsley <paul@pwsan.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
use gpio_request_<one|array>() instead of multiple gpiolib calls,
remove unneeded variables, etc.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently, omap_display_init() maintains arrays for hwmod name(oh_name) and the
correspnding platform_device name(dev_name) needed by omap_device_build().
A variable oh_count keeps a track of the number of devices to build from oh_name
based on what omap revision it is.
Clean this up by maintaining an array of omap_dss_hwmod_data struct which is
defined for each omap revision as suggested by Tomi Valkeinen. Assign the
corresponding omap_dss_hwmod_data array struct to the pointer curr_dss_hwmod in
omap_display_init().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Balaji T K