The reference clock configuration must be done before any mode setting
can occur as all outputs must be disabled to change
anything. Initialize the clocks after turning everything off during
the initialization process.
Also, re-initialize the refclk at resume time.
Signed-off-by: Keith Packard <keithp@keithp.com>
I can't find any reference clocks which run at 96MHz as seems to be
indicated from the comments in this code.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
When trying to use SSC on Ibex Peak without CK505, any non-SSC outputs
(like VGA or TV) get broken. So, do not use SSC on Ibex Peak unless
there is a CK505 available (as specified by the VBT).
On Cougar Point, all clocking is internal, so SSC can always be used,
and there will never be a CK505 available.
This eliminates VGA shimmer on some Ironlake machines which have a
CK505 clock source.
References: https://bugzilla.kernel.org/show_bug.cgi?id=21742
References: https://bugs.freedesktop.org/show_bug.cgi?id=38750
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
The PCH refclk settings are global, so we need to look at all of the
encoders, not just the current encoder when deciding how to configure
it. Also, handle systems with more than one panel (any combination of
PCH/non-PCH eDP and LVDS).
Disable SSC clocks when no panels are connected.
Signed-off-by: Keith Packard <keithp@keithp.com>
Allow SSC to be enabled even when the BIOS disables it for testing SSC paths.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Make the default FBC behaviour chipset specific, allowing us to turn
it on by default for Ironlake and older where it has been seen to
cause trouble with screen updates.
Signed-off-by: Keith Packard <keithp@keithp.com>
Tested-by: Francis Moreau <francis.moro@gmail.com>
Add ELD support for Intel Eaglelake, IbexPeak/Ironlake,
SandyBridge/CougarPoint and IvyBridge/PantherPoint chips.
ELD (EDID-Like Data) describes to the HDMI/DP audio driver the audio
capabilities of the plugged monitor. It's built and passed to audio
driver in 2 steps:
(1) at get_modes time, parse EDID and save ELD to drm_connector.eld[]
(2) at mode_set time, write drm_connector.eld[] to the Transcoder's hw
ELD buffer and set the ELD_valid bit to inform HDMI/DP audio driver
This patch is tested OK on G45/HDMI, IbexPeak/HDMI and IvyBridge/HDMI+DP.
Test scheme: plug in the HDMI/DP monitor, and run
cat /proc/asound/card0/eld*
to check if the monitor name, HDMI/DP type, etc. show up correctly.
Minor imperfection: the GEN5_AUD_CNTL_ST/DIP_Port_Select field always
reads 0 (reserved). Without knowing the port number, I worked it around
by setting the ELD_valid bit for ALL the three ports. It's tested to not
be a problem, because the audio driver will find invalid ELD data and
hence rightfully abort, even when it sees the ELD_valid indicator.
Thanks to Zhenyu and Pierre-Louis for a lot of valuable help and testing.
CC: Zhao Yakui <yakui.zhao@intel.com>
CC: Wang Zhenyu <zhenyu.z.wang@intel.com>
CC: Jeremy Bush <contractfrombelow@gmail.com>
CC: Christopher White <c.white@pulseforce.com>
CC: Pierre-Louis Bossart <pierre-louis.bossart@intel.com>
CC: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
We want to enable dithering on any pipe where the frame buffer has
more color resolution than the output device.
The previous code was incorrectly clamping the frame buffer bpc to the
display bpc, effectively disabling dithering all of the time as the
computed frame buffer bpc would never be larger than the display bpc.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reported-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
We want to enable dithering on any pipe where the frame buffer has
more color resolution than the output device.
The previous code was incorrectly clamping the frame buffer bpc to the
display bpc, effectively disabling dithering all of the time as the
computed frame buffer bpc would never be larger than the display bpc.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reported-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Various issues involved with the space character were generating
warnings in the checkpatch.pl file. This patch removes most of those
warnings.
Signed-off-by: Akshay Joshi <me@akshayjoshi.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Otherwise it just contains random memory.
Issue detected by cppcheck.
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
The commit "Not all systems expose a firmware or platform mechanism for
changing the backlight intensity on i915, so add native driver support"
adds calls to intel_panel_setup_backlight() from intel_{lvds,dp}_init
so do not call it again from intel_setup_outputs().
BugLink: http://bugs.launchpad.net/bugs/831542
Signed-off-by: Kamal Mostafa <kamal@canonical.com>
ACKed-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
We ought to be calling this from our DPMS routines as well as global
state may change and we need to enable/disable clocks. So split out the
code in preparation for further changes.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Just an extra parameter which isn't actually needed.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
CPT pipe select is different from previous generations (using two bits
instead of one). All of the paths from intel_disable_pch_ports were
not making this distinction.
Mode setting with pipe A turned off would then also force all outputs
on pipe B to get turned off as the disable code would mistakenly
decide that all of these outputs were on pipe A and turn them off.
This is an extension of the CPT DP disable fix (why didn't I fix this then?)
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The EDID parser will zero out the bpc value, and the driver needs to handle
that case. In our picker, we'll just ignore 0 values as far as bpp
picking goes.
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=39323.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
These bits moved around on SNB and above.
v2: again with the git send-email fail
v3: add macros for getting per-pipe override & enable bits
v4: enable phase sync pointer on SNB and IVB configs as well
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Using the new quirk added to support disabling SSC on Lenovo U160
(#36656, commit 435793dfb8), also register
the Vaio as a special case and disable SSC for it.
This patch fixes#34437 on fdo bugzilla:
https://bugs.freedesktop.org/show_bug.cgi?id=34437
Signed-off-by: Michel Alexandre Salim <salimma@fedoraproject.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
If a mode set fails we may get a message from drm_crtc_helper if we're lucky,
but it won't tell us anything about *why* we failed to set a mode. So
add a few DRM_ERRORs for the cases that shouldn't happen so we can debug
things more easily.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
CB tuning is needed to handle potential process variations that might
cause clock jitter for certain PLL settings. However, we were setting
it incorrectly since we were using the wrong M value as a check (M1 when
we needed to use the whole M value). Fix it up, making my HDMI
attached display a little prettier (used to have occasional dots crawl
across the display).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Writes to the plane control register are buffered in the chip until a
write to the DSPADDR (pre-965) or DSPSURF (post-965) register occurs.
This patch adds flushes in:
intel_enable_plane
gen6_init_clock_gating
ivybridge_init_clock_gating
Signed-off-by: Keith Packard <keithp@keithp.com>
After writing to the plane control reg we need to write to the surface
reg to trigger the double buffered register latch. On previous
chipsets, writing to DSPADDR was enough, but on ILK+ DSPSURF is the reg
that triggers the double buffer latch.
v2: write DSPADDR too to cover pre-965 chipsets
v3: use flush_display_plane instead, that's what it's for
v4: send the right patch
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
On CougarPoint and PantherPoint PCH chips, the timing generator may fail
to start after DP training completes. This is due to a bug in the
FDI autotraining detect logic (which will stall the timing generator and
re-enable it once training completes), so disable it to avoid silent DP
mode setting failures.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
This corrects the DPMS mode tracking so that the DPMS code will
actually turn the CRTC off the next time the screen saves.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Display port pipe selection on CPT is not done with a bit in the
output register, rather it is controlled by a couple of bits in the
separate transcoder register which indicate which display port output
is connected to the transcoder.
This patch replaces the simplistic macro DP_PIPE_ENABLED with the
rather more complicated function dp_pipe_enabled which checks the
output register to see if that is enabled, and then goes on to either
check the output register pipe selection bit (on non-CPT) or the
transcoder DP selection bits (on CPT).
Before this patch, any time the mode of pipe A was changed, any
display port outputs on pipe B would get disabled as
intel_disable_pch_ports would ensure that the mode setting operation
could occur on pipe A without interference from other outputs
connected to that pch port
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Adam Jackson <ajax@redhat.com>
If a mode set fails we may get a message from drm_crtc_helper if we're lucky,
but it won't tell us anything about *why* we failed to set a mode. So
add a few DRM_ERRORs for the cases that shouldn't happen so we can debug
things more easily.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
We've tried several times to make this machine 'just work', but every
patch that does causes many other machines to fail. This adds a quirk
which special cases this hardware and forces ssc to be
disabled. There's no way to override this from the command line; that
would be a significantly more invasive change.
This patch fixes#36656 on fdo bugzilla:
https://bugs.freedesktop.org/show_bug.cgi?id=36656
Signed-off-by: Keith Packard <keithp@keithp.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=36656
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Upon review, all path share the same dependencies for updating the
registers and so we can benefit from sharing the code and checking
early.
This removes the unsightly intel_wait_for_vblank() from the lowlevel
functions and upon further analysis the only path that will require a
wait is if we are performing an instantaneous transition between two
valid FBC configurations. The page-flip path itself will have disabled
FBC registers and will have waited for at least one vblank before
finishing the flip and attempting to re-enable FBC. This wait can be
accomplished simply by delaying the enable until after we are sure that
a vblank will have passed, which we are already doing to make sure that
the display is settled before enabling FBC.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
In order to accommodate the requirements of re-enabling FBC after
page-flipping, but to avoid doing so and incurring the cost of a wait
for vblank in the middle of a page-flip sequence, we defer the actual
enablement by 50ms. If any request to disable FBC arrive within that
interval, the enablement is cancelled and we are saved from blocking on
the wait.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Page-flipping updates the scanout address, nukes the FBC compressed
image and so forces an FBC update so that the displayed image remains
consistent. However, page-flipping does not update the FBC registers
themselves, which remain pointing to both the old address and the old
CPU fence. Future updates to the new front-buffer (scanout) are then
undetected!
This first approach to demonstrate the issue and highlight the fix,
simply disables FBC upon page-flip (a recompression will be forced on
every flip so FBC becomes immaterial) and then re-enables FBC in the
page-flip finish work function, so that the FBC registers are now
pointing to the new framebuffer and front-buffer rendering works once
more.
Ideally, we want to only re-enable FBC after page-flipping is complete,
as otherwise we are just wasting cycles and power (with needless
recompression) whilst the page-flipping application is still running.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=33487
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Persistent mode is intended for use with front-buffer rendering, such as
X, where it is necessary to detect writes to the scanout either by the
GPU or through the CPU's fence, and recompress the dirty regions on the
fly. (By comparison to the back-buffer rendering, the scanout is always
recompressed after a page-flip.)
References: https://bugs.freedesktop.org/show_bug.cgi?id=33487
References: https://bugs.freedesktop.org/show_bug.cgi?id=31742
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
...and this requirement is enforced by intel_update_fbc() so we can
remove the later check from g4x_enable_fbc() and ironlake_enable_fbc().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
The cfb_pitch was only used for 8xx_enable_fbc(), every later routine
was just overwriting the value with itself thanks to a copy'n'paste
error.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
...to ensure that any pending FBC enable tasklet is cancelled.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
As the enable/disable routines will be gain additional complexity in
future patches, it is necessary that all callers do not bypass the
generic interface by calling into the chipset routines directly. to do
this we make the chipset routines static, so there is no choice.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
This will catch bad fb configs earlier.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
Updating the planes is device specific, so create a new display callback
and use it in pipe_set_base. (In fact we could go even further, valid
display plane bits have changed with each generation, as has tiled
buffer handling.)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
Figuring out which pipe bpp to use is a bit painful. It depends on both
the encoder and display configuration attached to a pipe. For instance,
to drive a 24bpp framebuffer out to an 18bpp panel, we need to use 6bpc
on the pipe but also enable dithering. But driving that same
framebuffer to a DisplayPort output on another pipe means using 8bpc and
no dithering.
So split out and enhance the code to handle the various cases, returning
an appropriate pipe bpp as well as whether dithering should be enabled.
Save the resulting pipe bpp in the intel_crtc struct for use by encoders
in calculating bandwidth requirements (defaults to 24bpp on pre-ILK).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
This may not be the default value, so pull the bpc out of the pipe reg
and write it to the DP transcoder so proper dithering and signaling
occurs.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
This prevents us from setting reserved or incorrect bits on CougarPoint.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
They use the same register interfaces, so we can simply enable the
existing code on IVB.
v2:
- resolve conflict with ring freq scaling, we can enable it too
v3:
- resolve conflict again, this time on drm-intel-next
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
The ring frequency scaling table tells the PCU to treat certain GPU
frequencies as if they were a given CPU frequency for purposes of
scaling the ring frequency. Normally the PCU will scale the ring
frequency based on the CPU P-state, but with the table present, it will
also take the GPU frequency into account.
The main downside of keeping the ring frequency high while the CPU is
at a low frequency (or asleep altogether) is increased power
consumption. But then if you're keeping your GPU busy, you probably
want the extra performance.
v2:
- add units to debug table header (from Eric)
- use tsc_khz as a fallback if the cpufreq driver doesn't give us a freq
(from Chris)
v3:
- fix comments & debug output
- remove unneeded force wake get/put
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Tested-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard