Currently, nonlinear mappings can not be distinguished from ordinary
mappings. This patch adds into /proc/pid/smaps line "Nonlinear: <size>
kB", where size is amount of nonlinear ptes in vma, this line appears only
if VM_NONLINEAR is set. This information may be useful not only for
checkpoint/restore project.
Requested by Pavel Emelyanov.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently smaps reports migration entries as "swap", as result "swap" can
appears in shared mapping.
This patch converts migration entries into pages and handles them as usual.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is an implementation of Andrew's proposal to extend the pagemap file
bits to report what is missing about tasks' working set.
The problem with the working set detection is multilateral. In the criu
(checkpoint/restore) project we dump the tasks' memory into image files
and to do it properly we need to detect which pages inside mappings are
really in use. The mincore syscall I though could help with this did not.
First, it doesn't report swapped pages, thus we cannot find out which
parts of anonymous mappings to dump. Next, it does report pages from page
cache as present even if they are not mapped, and it doesn't make that has
not been cow-ed.
Note, that issue with swap pages is critical -- we must dump swap pages to
image file. But the issues with file pages are optimization -- we can
take all file pages to image, this would be correct, but if we know that a
page is not mapped or not cow-ed, we can remove them from dump file. The
dump would still be self-consistent, though significantly smaller in size
(up to 10 times smaller on real apps).
Andrew noticed, that the proc pagemap file solved 2 of 3 above issues --
it reports whether a page is present or swapped and it doesn't report not
mapped page cache pages. But, it doesn't distinguish cow-ed file pages
from not cow-ed.
I would like to make the last unused bit in this file to report whether the
page mapped into respective pte is PageAnon or not.
[comment stolen from Pavel Emelyanov's v1 patch]
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- use int fpr priority and nice, since task_nice()/task_prio() return that
- field 24: get_mm_rss() returns unsigned long
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pass "fd" directly, not via pointer -- one less memory read.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rcu_read_lock()/rcu_read_unlock() is nop for TINY_RCU, but is not a nop
for, say, PREEMPT_RCU.
proc_fill_cache() is called without RCU lock, there is no need to
lock/unlock on error path, simply jump out of the loop.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm_for_maps() is a simple wrapper for mm_access(), and the name is
misleading, so just remove it and use mm_access() directly.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Similar to e268337dfe ("proc: clean up and fix /proc/<pid>/mem
handling"), move the check of permission to open(), this will simplify
read() code.
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In embedded systems, sometimes the same program (busybox) is the cause of
multiple warnings. Outputting the pid with the program name in the
warning printk helps distinguish which instances of a program are using
the stack most.
This is a small patch, but useful.
Signed-off-by: Tim Bird <tim.bird@am.sony.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 8f92054e7c ("CRED: Fix __task_cred()'s lockdep check and banner
comment"):
add the following validation condition:
task->exit_state >= 0
to permit the access if the target task is dead and therefore
unable to change its own credentials.
OK, but afaics currently this can only help wait_task_zombie() which calls
__task_cred() without rcu lock.
Remove this validation and change wait_task_zombie() to use task_uid()
instead. This means we do rcu_read_lock() only to shut up the lockdep,
but we already do the same in, say, wait_task_stopped().
task_is_dead() should die, task->exit_state != 0 means that this task has
passed exit_notify(), only do_wait-like code paths should use this.
Unfortunately, we can't kill task_is_dead() right now, it has already
acquired buggy users in drivers/staging. The fix already exists.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: David Howells <dhowells@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Warning(kernel/kmod.c:419): No description found for parameter 'depth'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If we move call_usermodehelper_fns() to kmod.c file and EXPORT_SYMBOL it
we can avoid exporting all it's helper functions:
call_usermodehelper_setup
call_usermodehelper_setfns
call_usermodehelper_exec
And make all of them static to kmod.c
Since the optimizer will see all these as a single call site it will
inline them inside call_usermodehelper_fns(). So we loose the call to
_fns but gain 3 calls to the helpers. (Not that it matters)
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Both kernel/sys.c && security/keys/request_key.c where inlining the exact
same code as call_usermodehelper_fns(); So simply convert these sites to
directly use call_usermodehelper_fns().
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
call_usermodehelper_freeinfo() is not used outside of kmod.c. So unexport
it, and make it static to kmod.c
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently FAT file-system maps the VFS "superblock" abstraction to the
FSINFO block. The FSINFO block contains non-essential data about the
amount of free clusters and the next free cluster. FAT file-system can
always find out this information by scanning the FAT table, but having it
in the FSINFO block may speed things up sometimes. So FAT file-system
relies on the VFS superblock write-out services to make sure the FSINFO
block is written out to the media from time to time.
The whole "superblock write-out" VFS infrastructure is served by the
'sync_supers()' kernel thread, which wakes up every 5 (by default) seconds
and writes out all dirty superblock using the '->write_super()' call-back.
But the problem with this thread is that it wastes power by waking up the
system every 5 seconds no matter what. So we want to kill it completely
and thus, we need to make file-systems to stop using the '->write_super'
VFS service, and then remove it together with the kernel thread.
This patch switches the FAT FSINFO block management from
'->write_super()'/'->s_dirt' to 'fsinfo_inode'/'->write_inode'. Now,
instead of setting the 's_dirt' flag, we just mark the special
'fsinfo_inode' inode as dirty and let VFS invoke the '->write_inode'
call-back when needed, where we write-out the FSINFO block.
This patch also makes sure we do not mark the 'fsinfo_inode' inode as
dirty if we are not FAT32 (FAT16 and FAT12 do not have the FSINFO block)
or if we are in R/O mode.
As a bonus, we can also remove the '->sync_fs()' and '->write_super()' FAT
call-back function because they become unneeded.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Preparation for further changes. It touches few functions in fatent.c and
prevents them from marking the superblock as dirty unnecessarily often.
Namely, instead of marking it as dirty in the internal tight loops - do it
only once at the end of the functions. And instead of marking it as dirty
while holding the FAT table lock, do it outside the lock.
The reason for this patch is that marking the superblock as dirty will
soon become a little bit heavier operation, so it is cleaner to do this
only when it is necessary.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A preparation patch which introduces a 'mark_fsinfo_dirty()' helper
function which just sets the 's_dirt' flag to 1 so far. I'll add more
code to this helper later, so I do not mark it as 'inline'.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is patchset makes fatfs stop using the VFS '->write_super()' method
for writing out the FSINFO block.
The final goal is to get rid of the 'sync_supers()' kernel thread. This
kernel thread wakes up every 5 seconds (by default) and calls
'->write_super()' for all mounted file-systems. And the bad thing is that
this is done even if all the superblocks are clean. Moreover, some
file-systems do not even need this end they do not register the
'->write_super()' method at all (e.g., btrfs).
So 'sync_supers()' most often just generates useless wake-ups and wastes
power. I am trying to make all file-systems independent of
'->write_super()' and plan to remove 'sync_supers()' and '->write_super'
completely once there are no more users.
The '->write_supers()' method is mostly used by baroque file-systems like
hfs, udf, etc. Modern file-systems like btrfs and xfs do not use it.
This justifies removing this stuff from VFS completely and make every FS
self-manage own superblock.
Tested with xfstests.
This patch:
Preparation for further changes. It introduces a special inode
('fsinfo_inode') in FAT file-system which we'll later use for managing the
FSINFO block. Note, this there is already one special inode ('fat_inode')
which is used for managing the FAT tables.
Introduce new 'MSDOS_FSINFO_INO' constant for this special inode. It is
safe to do because FAT file-system does not store inode numbers on the
media but generates them run-time.
I've also cleaned up the comment to existing 'MSDOS_ROOT_INO' constant,
while on it.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The PRINTK() macro isn't really used. Let's just remove it because it
is ugly and out of date.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are two cases that the cache flush is needed to avoid data loss
against unexpected hang or power failure. One is sync file function (i.e.
nilfs_sync_file) and another is checkpointing ioctl.
This issues a cache flush request to device for such cases if barrier
mount option is enabled, and makes sure data really is on persistent
storage on their completion.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As described in commit 07d106d0a3 ("vfs: fix up ENOIOCTLCMD error
handling"), drivers should return -ENOIOCTLCMD if they receive an ioctl
command which they don't understand. Doing so will result in -ENOTTY
being returned to userspace, which matches the behaviour of the compat
layer if it fails to translate an ioctl command.
This patch fixes the pipe ioctl to return -ENOIOCTLCMD instead of -EINVAL
when passed an unknown ioctl command.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The init/mount.o source files produce a number of sparse warnings of the
type:
warning: incorrect type in argument 1 (different address spaces)
expected char [noderef] <asn:1>*dev_name
got char *name
This is due to the syscalls expecting some of the arguments to be user
pointers but they are being passed as kernel pointers. This is harmless
but adds a lot of noise to a sparse build.
To limit the noise just disable the sparse checking in the relevant source
files, but still display a warning so that the user knows this has been
done.
Since the sparse checking has been disabled we can also remove the __user
__force casts that are scattered thru the source.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Suggest the shorter pr_<level> instead of printk(KERN_<LEVEL>.
Prefer to use pr_<level> over bare printks.
Prefer to use pr_warn over pr_warning.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Andy Whitcroft <apw@shadowen.org>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Requires --strict option during invocation:
~/linux$ scripts/checkpatch --strict foo.patch
This tests for a bad habits of mine like this:
return 0 ;
Note that it does allow a special case of a bare semicolon
for empty loops:
while (foo())
;
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Andy Whitcroft <apw@canonical.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Previous code was using optimizations which were developed to work well
even on narrow-word CPUs (by today's standards). But Linux runs only on
32-bit and wider CPUs. We can use that.
First: using 32x32->64 multiply and trivial 32-bit shift, we can correctly
divide by 10 much larger numbers, and thus we can print groups of 9 digits
instead of groups of 5 digits.
Next: there are two algorithms to print larger numbers. One is generic:
divide by 1000000000 and repeatedly print groups of (up to) 9 digits.
It's conceptually simple, but requires an (unsigned long long) /
1000000000 division.
Second algorithm splits 64-bit unsigned long long into 16-bit chunks,
manipulates them cleverly and generates groups of 4 decimal digits. It so
happens that it does NOT require long long division.
If long is > 32 bits, division of 64-bit values is relatively easy, and we
will use the first algorithm. If long long is > 64 bits (strange
architecture with VERY large long long), second algorithm can't be used,
and we again use the first one.
Else (if long is 32 bits and long long is 64 bits) we use second one.
And third: there is a simple optimization which takes fast path not only
for zero as was done before, but for all one-digit numbers.
In all tested cases new code is faster than old one, in many cases by 30%,
in few cases by more than 50% (for example, on x86-32, conversion of
12345678). Code growth is ~0 in 32-bit case and ~130 bytes in 64-bit
case.
This patch is based upon an original from Michal Nazarewicz.
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Douglas W Jones <jones@cs.uiowa.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The '%p' output of the kernel's vsprintf() uses spec.field_width to
determine how many digits to output based on 2 * sizeof(void*) so that all
digits of a pointer are shown. ie. a pointer will be output as
"001A2B3C" instead of "1A2B3C". However, if the '#' flag is used in the
format (%#p), then the code doesn't take into account the width of the
'0x' prefix and will end up outputing "0x1A2B3C" instead of "0x001A2B3C".
This patch reworks the "pointer()" format hook to include 2 characters for
the '0x' prefix if the '#' flag is included.
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the module-wide pr_fmt() mechanism rather than open-coding "genirq: "
everywhere.
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sethostname() and setdomainname() notify userspace on failure (without
modifying uts_kern_table). Change things so that we only notify userspace
on success, when uts_kern_table was actually modified.
Signed-off-by: Sasikantha babu <sasikanth.v19@gmail.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: WANG Cong <amwang@redhat.com>
Reviewed-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver uses PCI_CLASS_REVISION instead of PCI_REVISION_ID, so it
wasn't converted by 44c10138fd ("PCI: Change all drivers to use
pci_device->revision").
In one case, it even reads PCI revision ID without using it -- that code
is now removed...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: "Nandigama, Nagalakshmi" <Nagalakshmi.Nandigama@lsi.com>
Cc: Eric Moore <eric.moore@lsi.com>
Acked-by: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the comment of allocate_resource(), the explanation of parameter max
and min is not correct.
Actually, these two parameters are used to specify the range of the
resource that will be allocated, not the min/max size that will be
allocated.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ULONG_MAX is often used to check for integer overflow when calculating
allocation size. While ULONG_MAX happens to work on most systems, there
is no guarantee that `size_t' must be the same size as `long'.
This patch introduces SIZE_MAX, the maximum value of `size_t', to improve
portability and readability for allocation size validation.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Acked-by: Alex Elder <elder@dreamhost.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the new kmalloc_array() to the list of general-purpose memory
allocators in chapter 14.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Acked-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit d065bd810b ("mm: retry page fault when blocking on disk
transfer") and commit 37b23e0525 ("x86,mm: make pagefault killable")
introduced changes into the x86 pagefault handler for making the page
fault handler retryable as well as killable.
These changes reduce the mmap_sem hold time, which is crucial during OOM
killer invocation.
Port these changes to um.
Signed-off-by: Kautuk Consul <consul.kautuk@gmail.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allocation may be large. The code is probing to see if it will
succeed and if not, it falls back to vmalloc(). We should suppress any
page-allocation failure messages when the fallback happens.
Reported-by: Dave Jones <davej@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=B6u0
-----END PGP SIGNATURE-----
Merge tag 'for-v3.5' of git://git.infradead.org/battery-2.6
Pull battery updates from Anton Vorontsov:
"A bunch of fixes for v3.5, nothing extraordinary."
* tag 'for-v3.5' of git://git.infradead.org/battery-2.6: (27 commits)
smb347-charger: Include missing <linux/err.h>
smb347-charger: Clean up battery attributes
max17042_battery: Add support for max17047/50 chip
sbs-battery.c: Capacity attr = remaining relative capacity
isp1704_charger: Use after free on probe error
ds2781_battery: Use DS2781_PARAM_EEPROM_SIZE and DS2781_USER_EEPROM_SIZE
power_supply: Fix a typo in BATTERY_DS2781 Kconfig entry
charger-manager: Provide cm_notify_event function for in-kernel use
charger-manager: Poll battery health in normal state
smb347-charger: Convert to regmap API
smb347-charger: Move IRQ enabling to the end of probe
smb347-charger: Rename few functions to match better what they are doing
smb347-charger: Convert to use module_i2c_driver()
smb347_charger: Cleanup power supply registration code in probe
ab8500: Clean up probe routines
ab8500_fg: Harden platform data check
ab8500_btemp: Harden platform data check
ab8500_charger: Harden platform data check
MAINTAINERS: Fix 'F' entry for the power supply class
max17042_battery: Handle irq request failure case
...
Pull two small kvm fixes from Avi Kivity:
"A build fix for non-kvm archs and a transparent hugepage refcount
bugfix on hosts with 4M pages."
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: Export asm-generic/kvm_para.h
KVM: MMU: fix huge page adapted on non-PAE host
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPx1M+AAoJEDeqqVYsXL0MNOMH/jSbgDAHQskBuZMCEoVUHykZ
3aKiPFJQfnF1nQqN/xxECGFc7glrKSHv1fpAG9wDk0HLHNhP+QoOBVYdDGHpzktk
eP1hB6rWE/auJz90rIrKomJoD+cVYDRHkhlbNr1DsYBuXI+BGX0aUp+uAaajoxAT
8wp4/Z5007llQQXnep2Z0AvzIWBdCeR4PBXX5YvalJ8Qz3Rj8bYeY10oDpx6nO7v
iGcyh+h0Eo+q9KEQ3PosoDnqaskq44yTY4MWeE1Kd64fQM1JYTJo0SxOGGVxHHwQ
ZLfhX+fH3jCyBP0qRzCqBvSKTuiWeMBc8POdLbLMnq6ClCgQTr41iHH7UTuXXjE=
=fZOy
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull final round of SCSI updates from James Bottomley:
"This is primarily another round of driver updates (bnx2fc, qla2xxx,
qla4xxx) including the target mode driver for qla2xxx. We've also got
a couple of regression fixes (async scanning, broken this merge window
and a fix to a long standing break in the scsi_wait_scan module)."
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (45 commits)
[SCSI] fix scsi_wait_scan
[SCSI] fix async probe regression
[SCSI] be2iscsi: fix dma free size mismatch regression
[SCSI] qla4xxx: Update driver version to 5.02.00-k17
[SCSI] qla4xxx: Capture minidump for ISP82XX on firmware failure
[SCSI] qla4xxx: Add change_queue_depth API support
[SCSI] qla4xxx: Fix clear ddb mbx command failure issue.
[SCSI] qla4xxx: Fix kernel panic during discovery logout.
[SCSI] qla4xxx: Correct early completion of pending mbox.
[SCSI] fcoe, bnx2fc, libfcoe: SW FCoE and bnx2fc use FCoE Syfs
[SCSI] libfcoe: Add fcoe_sysfs
[SCSI] bnx2fc: Allocate fcoe_ctlr with bnx2fc_interface, not as a member
[SCSI] fcoe: Allocate fcoe_ctlr with fcoe_interface, not as a member
[SCSI] Fix dm-multipath starvation when scsi host is busy
[SCSI] ufs: fix potential NULL pointer dereferencing error in ufshcd_prove.
[SCSI] qla2xxx: don't free pool that wasn't allocated
[SCSI] mptfusion: unlock on error in mpt_config()
[SCSI] tcm_qla2xxx: Add >= 24xx series fabric module for target-core
[SCSI] qla2xxx: Add LLD target-mode infrastructure for >= 24xx series
[SCSI] Revert "qla2xxx: During loopdown perform Diagnostic loopback."
...
Pull follow-up block updates from Jens Axboe:
"Includes the fix from Eric to resolve the infinite loop in looking up
or creating an IO context for an exiting task.
Also a bunch of mtip32xx patches. Fairly trivial stuff. It's fairly
new though, but no point in keeping it out of the tree until 3.6 imho.
I've thrown it through basic testing locally as well, works fine. The
one contentious part is the patch that Greg complained about (sysfs
file with multiple values, should be a debugfs file), which is
perfectly valid, but not a regression from what the file contains now.
That will be fixed up separately."
* 'for-linus' of git://git.kernel.dk/linux-block:
block: avoid infinite loop in get_task_io_context()
mtip32xx: Changes to sysfs entries
mtip32xx: Convert macro definitions for flag bits to enum
mtip32xx: minor performance tweak
mtip32xx: Fix to support more than one sector in exec_drive_command()
mtip32xx: Use plain spinlock for 'cmd_issue_lock'
mtip32xx: Set block queue boundary variables
mtip32xx: Fix to handle TFE for PIO(IOCTL/internal) commands
mtip32xx: Change HDIO_GET_IDENTITY to return stored data
mtip32xx: Set custom timeouts for PIO commands
mtip32xx: fix clearing an incorrect register in mtip_init_port
tty_lock_pair() do the right thing to avoid deadlocks, but should
instruct LOCKDEP of this to avoid a splat.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the same mechanism as the block devices are using, but move the
helper functions from fs/direct-io.c into fs/inode.c to remove the
dependency on CONFIG_BLOCK.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Fred Isaman <iisaman@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull s390 patches from Heiko Carstens:
"A couple of s390 patches for the 3.5 merge window. Just a collection
of bug fixes and cleanups."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/uaccess: fix access_ok compile warnings
s390/cmpxchg: select HAVE_CMPXCHG_LOCAL option
s390/cmpxchg: fix sign extension bugs
s390/cmpxchg: fix 1 and 2 byte memory accesses
s390/cmpxchg: fix compile warnings specific to s390
s390/cmpxchg: add missing memory barrier to cmpxchg64
s390/cpu: remove cpu "capabilities" sysfs attribute
s390/kernel: Fix smp_call_ipl_cpu() for offline CPUs
s390/kernel: Introduce memcpy_absolute() function
s390/headers: replace __s390x__ with CONFIG_64BIT where possible
s390/headers: remove #ifdef __KERNEL__ from not exported headers
s390/irq: split irq stats for cpu-measurement alert facilities
s390/kexec: Move early_pgm_check_handler() to text section
s390/kdump: Use real mode for PSW restart and kexec
s390/kdump: Account /sys/kernel/kexec_crash_size changes in OS info
s390/kernel: Remove OS info init function call and diag 308 for kdump
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPx039AAoJEDeqqVYsXL0Ml90H/06bB0sH5gpmJPOcMOcz2y5n
xZH4nHFGFfDUou/NFBkjBFAveBZDFy1WwsSwN44RZobmtkmqj9tfF90R0EoRsew6
kfRKJAn2iYA67WpM33v0ZpI+00VpNBt/sXP6OM08FebPu1aGriTnLm3qaOutyeC4
Q9dMHwhsMBjTcD52TlTlPBFHfOTvpB1FZmw//TwujPZ56upFw+dI1FkvzxdrG68a
ES7h8QBD8GXaM6OC8klCqq36iMjP2wJK3A+9MsERxkGLjfGEGMLC7jV3MgwvfjHY
i5w/EUheOU4SLicu7jBoC9mPHzhsWdl7OCP+E7V2CGXGysKSu4lH65ft1bMRIvg=
=ZAzL
-----END PGP SIGNATURE-----
Merge tag 'parisc-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6
Pull misc parisc updates from James Bottomley:
"This is a couple of updates to complete our fixes and one to fix a
compile failure caused during the merge window. Additionally, we now
switch to the generic strncopy_from_user."
* tag 'parisc-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6:
[PARISC] update parisc to use generic strncpy_from_user()
[PARISC] Fix parisc compile failure after smp: Add task_struct argument to __cpu_up()
[PARISC] fix TLB fault path on PA2.0 narrow systems
[PARISC] fix boot failure on 32-bit systems caused by branch stubs placed before .text
Pull additional x86 fixes from Peter Anvin.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, amd, xen: Avoid NULL pointer paravirt references
x86, mtrr: Fix a type overflow in range_to_mtrr func
x86, realmode: Unbreak the ia64 build of drivers/acpi/sleep.c
x86/mm/pat: Improve scaling of pat_pagerange_is_ram()
x86: hpet: Fix copy-and-paste mistake in earlier change
x86/mce: Fix 32-bit build
x86/bitops: Move BIT_64() for a wider use
This branch contains a few development patches for Samsung and Versatile
Express that were submitted to arm-soc near the beginning of the merge
window. We picked them up with the agreement that they would need to
sit in linux-next for a while, and now they have.
There are also two fixes:
- One long-standing build breakage on ixp4xx due to missing gpiolib
dependencies.
- The other is for some gpio device tree changes needed on lpc32xx.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=IA3W
-----END PGP SIGNATURE-----
Merge tag 'devel-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull late-merged development and first fixes for arm-soc from Olof Johansson:
"This branch contains a few development patches for Samsung and
Versatile Express that were submitted to arm-soc near the beginning of
the merge window. We picked them up with the agreement that they
would need to sit in linux-next for a while, and now they have.
There are also two fixes:
- One long-standing build breakage on ixp4xx due to missing gpiolib
dependencies.
- The other is for some gpio device tree changes needed on lpc32xx."
* tag 'devel-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: LPC32xx: Adjust dts files to gpio dt binding
ixp4xx: fix compilation by adding gpiolib support
ARM: vexpress: Remove twice included header files
ARM: vexpress: Device Tree updates
ARM: EXYNOS: Support suspend and resume for EXYNOS5250
ARM: EXYNOS: Add Clock register list for save and restore
ARM: EXYNOS: Add PMU table for EXYNOS5250
ARM: EXYNOS: Rename of function for pm.c
ARM: EXYNOS: Remove GIC save & restore function
ARM: dts: Add node for interrupt combiner controller on EXYNOS5250
ARM: S3C24XX: add support for second irq set of S3C2416
ARM: S3C64XX: use timekeeping wrapper on cpuidle
ARM: S3C64XX: declare the states with the new api on cpuidle
ARM: S3C64XX: Hook up carrier class modules on Cragganmore
ARM: S3C64XX: Initial hookup for Bells module on Cragganmore
Konstantin Khlebnikov