* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 3540/1: ixp23xx: deal with gap in interrupt bitmasks
[ARM] 3539/1: ixp23xx: fix __arch_ixp23xx_is_coherent() for A1 stepping
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Fix D-cache corruption in mremap
[SPARC64]: Make smp_processor_id() functional before start_kernel()
Patch from Lennert Buytenhek
On the ixp23xx, the microengine thread interrupt sources are numbered
56..119, but their mask/status bits are located in bit positions 64..127
in the various registers in the interrupt controller (bit positions
56..63 are unused.)
We don't deal with this, so currently, when asked to enable IRQ 64, we
will enable IRQ 56 instead.
The only interrupts >= 64 are the thread interrupt sources, and there
are no in-tree users of those yet, so this is fortunately not a big
problem, but this needs fixing anyway.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Treat R14000 like R10000.
[MIPS] Remove EXPERIMENTAL from PAGE_SIZE_16KB
[MIPS] Update/Fix instruction definitions
[MIPS] DSP and MDMX share the same config flag bit.
[MIPS] Fix deadlock on MP with cache aliases.
[MIPS] Use generic STABS_DEBUG macro.
[MIPS] Create consistency in "system type" selection.
[MIPS] Use generic DWARF_DEBUG
[MIPS] Fix kgdb exception handler from user mode.
[MIPS] Update struct sigcontext member names
[MIPS] Update/fix futex assembly
[MIPS] Remove support for sysmips(2) SETNAME and MIPS_RDNVRAM operations.
[MIPS] Fix detection and handling of the 74K processor.
[MIPS] Add missing 34K processor IDs
[MIPS] Fix marking buddy of pte global for MIPS32 w/36-bit physical address
[MIPS] AU1xxx mips_timer_interrupt() fixes
[MIPS] Fix typo
A proper fix would involve introducing the notion of shared caches but
at this stage of 2.6.17 that's going to be too intrusive and not needed
for current hardware; aside I think some discussion will be needed.
So for now on the affected SMP configurations which happen to suffer from
cache aliases we make use of the fact that a single cache will be shared
by all processors. This solves the deadlock issue and will improve
performance by getting rid of the smp_call_function overhead.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The "system type" Kconfig options on MIPS are not consistent. For
some platforms, only the name is listed while other entries are
prepended with "Support for". Remove this as it doesn't make sense
when describing the "system type".
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When debugging a kernel compiled by gcc 4.1 with gdb 6.4, gdb could
not show filename, linenumber, etc. It seems fixed if I used generic
DWARF_DEBUG macro. Although gcc 3.x seems work without this change,
it would be better to use the generic macro unless there were
something MIPS specific.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Rename the 64-bit sc_hi and sc_lo arrays to use the same names
as the 32-bit struct sigcontext (sc_mdhi, sc_hi1, et cetera).
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
SETNAME only had a minor defect but probably never had a user and
MIPS_RDNVRAM was unimplemented anyway.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Nothing exciting; Linux just didn't know it yet so this is most adding
a value to a case statement.
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
common/au1000/irq.c was missing a mips_timer_interrupt() prototype,
whereas in common/au1000/time.c the actual mips_timer_interrupt()
implementation was missing an irq_exit() invocation, causing a
preempt_count() leak.
Signed-off-by: Herbert Valerio Riedel <hvr@hvrlab.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The ARM Architecture Reference Manual lists bit 4 of the PMD as "implementation
defined" and it must be set to zero on Intel XScale CPUs or the cache does
not behave properly. Found by Mike Rapoport while debugging a flash issue
on the PXA255:
http://marc.10east.com/?l=linux-arm-kernel&m=114845287600782&w=1
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Prevent calling of some platform functions on the clock chips of the eMac
as it seems to cause it to lockup at boot. For now, add a quirk to prevent
that from happening. Later, I might find out what's wrong and fix it but
that doesn't seem to be important as the machine appear to work fine
without running those. It's possible that Darwin doesn't run them.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Nathan Pilatzke <nathanpilatzke@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Uses of smp_processor_id() get pushed earlier and earlier in
the start_kernel() sequence. So just get it working before
we call start_kernel() to avoid all possible problems.
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't enable the BTB on the ixp2350 as that can cause weird
crashes (erratum #42.) However, some bootloaders enable the BTB,
which means that we have to disable the BTB explicitly.
Found thanks to Tom Rini.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This reverts commit 5491d0f3e2.
As per Andi:
"After some discussion with people who have the affected system it
seems best to revert for 2.6.17. It broke a common BIOS workaround
and PCI-X still doesn't work. Alternative is for people to change
the BIOS which seems to be better right now."
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
int_ret_from_syscall already does syscall exit tracing, so
no need to do it again in the caller.
This caused problems for UML and some other special programs doing
syscall interception.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Robert Hentosh <robert_hentosh@dell.com>
Actually, we just stumbled on a different bug found in find_e820_area() in
e820.c. The following code does not handle the edge condition correctly:
while (bad_addr(&addr, size) && addr+size < ei->addr + ei->size)
;
last = addr + size;
if ( last > ei->addr + ei->size )
continue;
The second statement in the while loop needs to be a <= b so that it is the
logical negavite of the if (a > b) outside it. It needs to read:
while (bad_addr(&addr, size) && addr+size <= ei->addr + ei->size)
;
In the case that failed bad_addr was returning an address that is exactly size
bellow the end of the e820 range.
AK: Again together with the earlier avoid edma fix this fixes
boot on a Dell PE6850/16GB
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Daniel Yeisley <dan.yeisley@unisys.com>
It is possible to boot a Unisys ES7000 with CPUs from multiple cells, and not
also include the memory from those cells. This can create a scenario where
node 0 has cpus, but no associated memory. The system will boot fine in a
configuration where node 0 has memory, but nodes 2 and 3 do not.
[AK: I rechecked the code and generic code seems to indeed handle that already.
Dan's original patch had a change for mm/slab.c that seems to be already in now.]
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: "Jan Beulich" <jbeulich@novell.com>
The PM timer code updates vxtime.last_tsc, but this update was done
incorrectly in two ways:
- offset_delay being in microseconds requires multiplying with cpu_mhz
rather than cpu_khz
- the multiplication of offset_delay and cpu_khz (both being 32-bit
values) on most current CPUs would overflow (observed value of the
delay was approximately 4000us, yielding an overflow for frequencies
starting a little above 1GHz)
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: "Jan Beulich" <jbeulich@novell.com>
When using apic= on the kernel command line, this had no effect for machines
matched by either the ACPI MADT or the MPS OEM table scan. However, when such
option is specified, it should also take effect for this set of systems.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Complaining about the IOMMU not compiled in doesn't make sense
here because it is clearly compiled in.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ia32_setup_arg_pages would ignore the passed in random stack top
and use its own static value.
Now it uses the 8bit of randomness native i386 would use too.
This indirectly fixes mmap randomization for 32bit processes too,
which depends on the stack randomization.
Should also give slightly better virtual cache colouring and
possibly better performance with HyperThreading.
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A typo crept in with commit ea1e847cc2
which defined TI_LOCAL_FLAGS to be the offset of the `flags' field
of struct thread_info, rather than the `local_flags' field. This
fixes it. The typo was pointed out by Guennadi Liakhovetski.
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[PATCH] powerpc: fix RTC/NVRAM accesses on Maple
[PATCH] ppc32 CPM_UART: various fixes for pq2 uart users
[PATCH] powerpc: linuxppc64.org no more
For a very long time, echoing 'standby' or 'mem' into /sys/power/state has
killed the machine on powerpc. This patch fixes that.
This patch adds the .valid callback to pm_ops on PowerMac so that only the
suspend to disk state can be entered. Note that just returning 0 would
suffice since the upper layers don't pass PM_SUSPEND_DISK down, but we
handle it there regardless just in case that changes.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Due to a firmware device tree bug, RTC and NVRAM accesses (including
halt/reboot) on Maple have been broken since January, when an untested
build fix went in. This code patches the device tree in Linux.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes various odd things that missed update together with cpm_uart
platform_device move. Unified resources names, restructurisation, etc.
Also, addressed issue with recent phys/virt translation rework. Being
cache-coherent, CPM2's do alloc_bootmem() for the console stuff, and it was
used to treat console buffer descriptor mapping 1:1 (as in CPM1 case),
which is definitely wrong.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add missing parentheses for type cast to u64.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Syscall number 224 was absent from the table, which I believe means that
the SPU can cause an oops by attempting to use it.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Writing cr0 to cr2 register can't be right. This fixes the typo. I wonder
how it could survive so long.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Using asm-generic/dma-mapping.h does not work because pushing
the call down to pci_alloc_coherent() causes the gfp_t argument
of dma_alloc_coherent() to be ignored.
Fix this by implementing things directly, and adding a gfp_t
argument we can use in the internal call down to the PCI DMA
implementation of pci_alloc_coherent().
This fixes massive memory corruption when using the sound driver
layer, which passes things like __GFP_COMP down into these
routines and (correctly) expects that to work.
Signed-off-by: David S. Miller <davem@davemloft.net>
The 32 bit unsigned substraction (next - jiffies) in stop_hz_timer can
overflow if jiffies gets advanced between next_timer_interrupt and the read
under the xtime lock. The cast to a u64 then results in a large value
which causes the cpu to wait too long. Fix this by casting next and
jiffies independently to u64 before subtracting them.
(Spotted by Zachary Amsden <zach@vmware.com>)
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Problem:
If we put a probe onto a callq instruction and the probe is executed,
kernel panic of Bad RIP value occurs.
Root cause:
If resume_execution() found 0xff at first byte of p->ainsn.insn, it must
check the _second_ byte. But current resume_execution check _first_ byte
again.
I changed it checks second byte of p->ainsn.insn.
Kprobes on i386 don't have this problem, because the implementation is a
little bit different from x86_64.
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Satoshi Oshima <soshima@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o Kdump second kernel boot fails after a system crash if second kernel
is UP and acpi=off and if crash occurred on a non-boot cpu.
o Issue here is that MP tables report boot cpu lapic id as 0 but second
kernel is booting on a different processor and MP table data is stale
in this context. Hence apic_id_registered() check fails in setup_local_APIC()
when called from APIC_init_uniprocessor().
o Problem is not seen if ACPI is enabled as in that case
boot_cpu_physical_apicid is read from the LAPIC.
o Problem is not seen with SMP kernels as well because in this case also
boot_cpu_physical_apicid is read from LAPIC. (smp_boot_cpus()).
o The problem is fixed by reading boot_cpu_physical_apicid from LAPIC
if it is a UP kernel and CRASH_DUMP is enabled.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
i386 stack dump has a "<0>" in the middle of the line and an extra space
between columns in multicolumn mode. Remove those and also remove an extra
blank line of source code.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 3533/1: Implement the __raw_(read|write)_can_lock functions on ARM
[ARM] 3530/1: PXA Mainstone: prevent double enable_irq() in pcmcia
[ARM] 3529/1: s3c24xx: fix restoring control register with undefined instruction
Patch from Thomas Gleixner
The mainstone board pcmcia interrupt have been enabled via setup_irq()
and the following socket check calls enable_irq again. Set the NOAUTOEN flag so the interrupt is not automatically enabled in setup_irq()
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Dimitry Andric
In arch/arm/mach-s3c2410/sleep.S, the coprocessor registers are saved at
suspend time, and restored at resume time. However, an undefined
instruction is used when attempting to restore a non-existent "auxiliary
control register". This leads to a crash on S3C2412, which has an ARM926
core instead of an ARM920.
At suspend time, the following fragment runs:
mrc p15, 0, r7, c2, c0, 0 @ translation table base address
mrc p15, 0, r8, c2, c0, 0 @ auxiliary control register
mrc p15, 0, r9, c1, c0, 0 @ control register
and at resume time, the following fragment runs:
mcr p15, 0, r7, c2, c0, 0 @ translation table base
mcr p15, 0, r8, c1, c1, 0 @ auxilliary control
...
mcr p15, 0, r9, c1, c0, 0 @ turn on MMU, etc
There are several problems with these fragments:
1. The ARM920 and ARM926 cores don't have any "auxiliary control
register", at least not according to the ARM920 and ARM926 TRM's.
2. The 2nd line of suspend erroneously saves the c2 register again.
3. This saved c2 value is restored using an undefined instruction. For
some reason this does not crash on ARM920, but does crash on ARM926.
The following patch fixes all these problems.
Signed-off-by: Dimitry Andric <dimitry@andric.com>
Yes, this looks sensible
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Calls to set_irq_info in set_irq_affinity_info() is redundant because
irq_affinity mask was set just one line immediately above it. Remove
that duplicate call.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When CONFIG_PCI_MSI is set, move_irq() is an empty function, causing
grief when sys admin tries to bind interrupt to CPU.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] arch/arm/kernel/dma-isa.c: named initializers
[ARM] 3527/1: MPCore Boot Lockup Fix
[ARM] arch/arm/kernel/process.c: Fix warning
[ARM] 3526/1: ioremap should use vunmap instead of vfree on ARM
[ARM] 3524/1: ARM EABI: more 64-bit aligned stack fixes
[ARM] 3517/1: move definition of PROC_INFO_SZ from procinfo.h to asm-offsets.h
This patch converts struct dma_resources to named initializers.
Besides fixing a compile error in -mm, it didn't sound like a bad idea.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Alexander Schulz <alex@shark-linux.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Harry Fearnhamm
This patch fixes the occasional lockup seen in early boot stage
on RealView MPCore system.
Signed-off-by: Harry Fearnhamm <Harry.Fearnhamm@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[PATCH] Fix pSeries identification in prom_init.c
[PATCH] powerpc: fix kernel version display on pseries boxes
Extends an earlier patch from John Blackwood to more exception handlers
that also run on the exception stacks.
Expand the use of preempt_conditional_{sti,cli} to all cases where
interrupts are to be re-enabled during exception handling while running
on an IST stack.
Based on original patch from Jan Beulich.
Cc: John Blackwood <john.blackwood@ccur.com>
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes some boot failures on Dell and Unisys systems with memory
hotadd added.
- Set hotadd_percent to 0 by default. This means anybody using hotadd
memory needs to specify the value on the command line. That's
because there are lots of Intel boxes which have a bogus hotplug area
in their SRAT and they would waste a lot of memory before.
- Fix calculation of how much memory to use when the hotplug area
exceeds hotadd_percent
- Fix fallback when the
- Fix fallback if memory hotadd is not compiled in.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is needed to see all devices.
The system has multiple PCI segments and we don't handle that properly
yet in PCI and ACPI. Short term before this is fixed blacklist it to
pci=noacpi.
Acked-by: len.brown@intel.com
Cc: gregkh@suse.de
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This triggers for b44's 1GB DMA workaround which tries to map
first and then bounces.
The 32bit heuristic is reasonable because the IOMMU doesn't attempt
to handle < 32bit masks anyways.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The OF trampoline code prom_init.c still needs to identify IBM pSeries
(PAPR) machines in order to run some platform specific code on them like
instanciating the TCE tables. The code doing that detection was changed
recently in 2.6.17 early stages but was done slightly incorrectly. It
should be testing for an exact match of "chrp" and it currently tests
for anything that begins with "chrp". That means it will incorrectly
match with platforms using Maple-like device-trees and have open
firmware. This fixes it by using strcmp instead of strncmp to match what
the actual platform detection code does.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We are displaying the wrong thing on the operator panel (2x40
character LCD). This got broken in commit cebb21b5, when UTS_RELEASE
got changed to system_utsname.version.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Patch from Catalin Marinas
This patch modifies the __ioremap_pfn and __iounmap functions in
arch/arm/mm/ioremap.c to use vunmap instead of vfree.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Assembly code that calls C code must ensure the C code sees a 64-bit
aligned stack pointer.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Uwe Zeisberger
The symbol is only used in arch/arm/kernel/head-common.S. This in turn
is included from arch/arm/kernel/head.S and arch/arm/kernel/head-nommu.S
which include asm-offsets.h .
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
HOTPLUG_CPU entry says "Say Y..." then "Say N.". Slightly ugly, so I fixed
it up, and added remark about suspend on SMP as a bonus.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support to oprofile for the Intel Core Solo and Core Duo processors.
See also the patch to add support to oprofile-0.9.1-8.1.1 at
http://www.kvack.org/~bcrl/patches/oprofile/oprofile-core-0.9.1.diff .
Signed-off-by: Benjamin LaHaise <benjamin.c.lahaise@intel.com>
Cc: Philippe Elie <phil.el@wanadoo.fr>
Cc: John Levon <levon@movementarian.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add new vmsplice system call and add missing __NR_xxx defines for
sys_set_robust_list, sys_get_robust_list, sys_splice, sys_sync_file_range
and sys_tee.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Exploit rcu_needs_cpu() interface to keep the cpu 'ticking' if necessary.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This reverts commit 10dbe196a8.
The resource struct is still 32-bit, so trying to save a 64-bit memory
size there obviously won't work.
When we merge the 64-bit resource series, we can re-enable this.
Thanks to Sachin Sant and Maneesh Soni for debugging
Cc: Maneesh Soni <maneesh@in.ibm.com>
Cc: Sachin Sant <sachinp@in.ibm.com>
Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Cc: Sharyathi Nagesh <sharyath@in.ibm.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC]: Fix warning on prom_getproperty in openprom.c
[SPARC]: Handle UNWIND_INFO properly.
[SPARC64]: Update defconfig.
[SPARC]: show device name in /proc/dvma_map
[SPARC]: Remove duplicate symbol exports
For sparc32 we need R_SPARC_UA32 relocation support, for
sparc64 we need the handle R_SPARC_DISP32 relocations.
Based upon reports and initial patch by Martin Habets.
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Pavel Machek
Update collie defconfig to something that can bring closer-to-working
system to its user.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ARM thread struct allocator is racy on SMP systems. Fix it by
turning it into a per-cpu based allocator. This also allows keeps
the cache cache warm for thread structs and kernel stacks.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Instantiation of 8MB pages on the TLB cache for the kernel static
mapping trashes r3 register on !CONFIG_8xx_CPU6 configurations.
This ensures r3 gets saved and restored.
Signed-off-by: Marcelo Tosatti <marcelo@kvack.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Update versatile default configuration, enabling the AACI sound driver,
VFP and Versatile AB support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Based on analysis&patch from Robert Hentosch
Observed on a Dell PE6850 with 16GB
The problem occurs very early on, when the kernel allocates space for the
temporary memory map called bootmap. The bootmap overlaps the EBDA region.
EBDA region is not historically reserved in the e820 mapping. When the
bootmap is freed it marks the EBDA region as usable.
If you notice in setup.c there is already code to work around the EBDA
in reserve_ebda_region(), this check however occurs after the bootmap
is allocated and doesn't prevent the bootmap from using this range.
AK: I redid the original patch. Thanks also to Jan Beulich for
spotting some mistakes.
Cc: Robert_Hentosch@dell.com
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Playing with NMI watchdog on x86_64, I discovered that it didn't
do what I expected. It always panic-ed, even when it didn't
happen from interrupt context. This patch solves that
problem for me. Also, in this case, do_exit() will be called
with interrupts disabled, I believe. Would it be wise to also
call local_irq_enable() after nmi_exit()?
[Yes I added it -AK]
Currently, on x86_64, any NMI watchdog timeout will cause a panic
because the irq count will always be set to be in an interrupt
when do_exit() is called from die_nmi(). If we add nmi_exit() to
the die_nmi() call (since the nmi will never exit "normally")
it seems to solve this problem. The following small program
can be used to trigger the NMI watchdog to reproduce this:
main ()
{
iopl(3);
for (;;) asm("cli");
}
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I noticed this when poking around in this area.
The oops_begin() function in x86_64 would only conditionally claim
the die_lock if the call is nested, but oops_end() would always
release the spinlock. This patch adds a nest count for the die lock
so that the release of the lock is only done on the final oops_end().
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The IOMMU code can only deal with 8 northbridges. Error out when
more are found.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The patch addresses a problem with ACPI SCI interrupt entry, which gets
re-used, and the IRQ is assigned to another unrelated device. The patch
corrects the code such that SCI IRQ is skipped and duplicate entry is
avoided. Second issue came up with VIA chipset, the problem was caused by
original patch assigning IRQs starting 16 and up. The VIA chipset uses
4-bit IRQ register for internal interrupt routing, and therefore cannot
handle IRQ numbers assigned to its devices. The patch corrects this
problem by allowing PCI IRQs below 16.
Cc: len.brown@intel.com
Signed-off by: Natalie Protasevich <Natalie.Protasevich@unisys.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch will set the device name in a resource, which will be shown
in /proc/dvma_map.
Signed-off-by: Martin Habets <errandir_news@mph.eclipse.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resolves the following build warnings seen in 2.6.17-rc3:
WARNING: vmlinux: 'sys_close' exported twice. Previous export was in vmlinux
WARNING: vmlinux: 'memchr' exported twice. Previous export was in vmlinux
WARNING: vmlinux: 'strstr' exported twice. Previous export was in vmlinux
WARNING: vmlinux: 'strnlen' exported twice. Previous export was in vmlinux
WARNING: vmlinux: 'strrchr' exported twice. Previous export was in vmlinux
WARNING: vmlinux: 'strchr' exported twice. Previous export was in vmlinux
WARNING: vmlinux: 'strcmp' exported twice. Previous export was in vmlinux
WARNING: vmlinux: 'strncat' exported twice. Previous export was in vmlinux
WARNING: vmlinux: 'strcat' exported twice. Previous export was in vmlinux
WARNING: vmlinux: 'strncpy' exported twice. Previous export was in vmlinux
WARNING: vmlinux: 'strcpy' exported twice. Previous export was in vmlinux
Signed-off-by: Martin Habets <errandir_news@mph.eclipse.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Bellido Nicolas
aaed2000 map_desc.pfn conversion
Signed-off-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Bellido Nicolas
Since this patch:
[ARM] 3366/1: Allow the 16bpp mode configuration in the CLCD control register
linux/amba/bus.h needs to be included before linux/amba/clcd.h
Signed-off-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Bellido Nicolas
Patch:
[ARM] 2982/1: Replace map_desc.physical with map_desc.pfn: aaec2000
incorrectly expanded the struct map_desc for aaec2000.
Signed-off-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Sascha Hauer
This patch fixes the addruart macro to work with both mmu enabled and
disabled.
Signed-off-by: Sascha Hauer <s.hauer@pengutonix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The SA1100 RTC alarm can be configured to wake up the CPU
from sleep mode, and the RTC driver has been using the
API to configure this mode. Unfortunately, the code was
which sets the required bit in the hardware was missing.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Intel PXA27x developers manual section 5.4.1.1 lists a priority
distribution for the DMA channels differently than what the code
currently assumes. This patch fixes that.
Noticed by Simon Vogl <vogl@soft.uni-linz.ac.at>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from George G. Davis
The ARM VFP FPSCR register is corrupted when a condition flags modifying
VFP instruction is followed by a non-condition flags modifying VFP
instruction and both instructions raise exceptions. The fix is to
read the current FPSCR in between emulation of these two instructions
and use the current FPSCR value when handling the second exception.
Signed-off-by: George G. Davis <gdavis@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Bob Picco noted that 6edfba1b33
dropped the -ffreestanding compiler flag from the top level
Makefile, which allows the compiler to substitute memcpy() in
places where strcpy() is used with a known size source string.
But the ia64 memcpy() returns 0 for success, and "bytes copied"
for failure.
Fix to return the address of the destination string (like
stdlibc version, and other architectures). There are no
places where ia64 specific code makes use of the non-standard
return value.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Egry Gabor