Link resets leave ata affiliations intact, so arrange for libsas to make
an effort to avoid dropping the device due to a slow-to-recover link.
Towards this end carry out reset in the host workqueue so that it can
check for ata devices and kick the reset request to libata. Hard
resets, in contrast, bypass libata since they are meant for associating
an ata device with another initiator in the domain (tears down
affiliations).
Need to add a new transport_sas_phy_reset() since the current
sas_phy_reset() is a utility function to libsas lldds. They are not
prepared for it to loop back into eh.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Extend the sas transport class to allow transport users to attach extra
data to a sas_phy (->hostdata). Use this area in libsas to move resets
to workq context in preparation for scheduling ata device resets through
libata-eh.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Since sata devices can take several seconds to recover the link on reset
the 0.5 seconds that libsas currently waits may not be enough. Instead
if we are rediscovering a phy that was previously attached to a sata
device let libata handle any resets to encourage the device to transmit
the initial fis.
Once sas_ata_hard_reset() and lldds learn how to honor 'deadline' libsas
should stop encountering phys in an intermediate state, until then this
will loop until the fis is transmitted or ->attached_sas_addr gets
cleared, but in the more likely initial discovery case we keep existing
behavior.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
lldds use the SAS_TASK_NEED_DEV_RESET interface to request that eh
perform a reset. In the sata device case defer the commands that
triggered the reset to libata-eh context so it can perform its pre and
post reset management.
In the sas_ata_post_internal() case the reset request is falling on deaf
ears as the sas_task is immediately destroyed without any reset action.
Since it is currently a nop, and likely superfluous given the conversion
to new-style libata-eh, just drop the request.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
libsas-eh if it successfully aborts an ata command will hide the timeout
condition (AC_ERR_TIMEOUT) from libata. The command likely completes
with the all-zero task->task_status it started with. Instead, interpret
a TMF_RESP_FUNC_COMPLETE as the end of the sas_task but keep the scmd
around for libata-eh to handle.
Tested-by: Andrzej Jakowski <andrzej.jakowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Until we have told the lldd to forget a task a timed out operation can
return from the hardware at any time. Since completion frees the task
we need to make sure that no tasks run their normal completion handler
once eh has decided to manage the task. Similar to
ata_scsi_cmd_error_handler() freeze completions to let eh judge the
outcome of the race.
Task collector mode is problematic because it presents a situation where
a task can be timed out and aborted before the lldd has even seen it.
For this case we need to guarantee that a task that an lldd has been
told to forget does not get queued after the lldd says "never seen it".
With sas_scsi_timed_out we achieve this with the ->task_queue_flush
mutex, rather than adding more time.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We invoke task->task_done() to free the task in the eh case, but at this
point we are prepared for scsi_eh_flush_done_q() to finish off the scmd.
Introduce sas_end_task() to capture the final response status from the
lldd and free the task.
Also take the opportunity to kill this warning.
drivers/scsi/libsas/sas_scsi_host.c: In function ‘sas_end_task’:
drivers/scsi/libsas/sas_scsi_host.c:102:3: warning: case value ‘2’ not in enumerated type ‘enum exec_status’ [-Wswitch]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Since sas_ata does not implement ->freeze(), completions for scmds and
internal commands can still arrive concurrent with
ata_scsi_cmd_error_handler() and sas_ata_post_internal() respectively.
By the time either of those is called libata has committed to completing
the qc, and the ATA_PFLAG_FROZEN flag tells sas_ata_task_done() it has
lost the race.
In the sas_ata_post_internal() case we take on the additional
responsibility of freeing the sas_task to close the race with
sas_ata_task_done() freeing the the task while sas_ata_post_internal()
is in the process of invoking ->lldd_abort_task().
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Prior to the conversion to the new-style libata-eh sas_ata_task_done()
may have been the last opportunity to clean up the scmd, but now
libata-eh explicitly handles this case. It also races against sas-eh.
If a lldd completes a task after SAS_TASK_STATE_ABORTED is set it could
trigger a spurious decrement of shost->host_failed. Current lldds have
the band-aid of checking SAS_TASK_STATE_ABORTED before calling
->task_done(), but better to just let the scmds escalate to libata for
race free cleanup.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
sas_discover_sata() notifies lldds of sata devices twice. Once to allow
the 'identify' to be sent, and a second time to allow aic94xx (the only
libsas driver that cares about sata_dev.identify) to setup NCQ
parameters before the device becomes known to the midlayer. Replace
this double notification and intervening 'identify' with an explicit
->lldd_ata_set_dmamode notification. With this change all ata internal
commands are issued by libata, so we no longer need sas_issue_ata_cmd().
The data from the identify command only needs to be cached in one
location so ata_device.id replaces domain_device.sata_dev.identify.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
libata error handling provides for a timeout for link recovery. libsas
must not rescan for previously known devices in this interval otherwise
it may remove a device that is simply waiting for its link to recover.
Let libata-eh make the determination of when the link is stable and
prevent libsas (host workqueue) from taking action while this
determination is pending.
Using a mutex (ha->disco_mutex) to flush and disable revalidation while
eh is running requires any discovery action that may block on eh be
moved to its own context outside the lock. Probing ATA devices
explicitly waits on ata-eh and the cache-flush-io issued during device
removal may also pend awaiting eh completion. Essentially any rphy
add/remove activity needs to run outside the lock.
This adds two new cleanup states for sas_unregister_domain_devices()
'allocated-but-not-probed', and 'flagged-for-destruction'. In the
'allocated-but-not-probed' state dev->rphy points to a rphy that is
known to have not been through a sas_rphy_add() event. At domain
teardown check if this device is still pending probe and cleanup
accordingly. Similarly if a device has already been queued for removal
then sas_unregister_domain_devices has nothing to do.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In preparation for adding tracking of another device state "destroy".
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Each libsas driver (mvsas, pm8001, and isci) has invented a different
method for managing the ap->lock. The lock is held by the ata
->queuecommand() path. mvsas drops it prior to acquiring any internal
locks which allows it to hold its internal lock across calls to
task->task_done(). This capability is important as it is the only way
the driver can flush task->task_done() instances to guarantee that it no
longer has any in-flight references to a domain_device at
->lldd_dev_gone() time.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When an lldd invokes ->notify_port_event() it can trigger a chain of libsas
events to:
1/ form the port and find the direct attached device
2/ if the attached device is an expander perform domain discovery
A call to flush_workqueue() will only flush the initial port formation work.
Currently libsas users need to call scsi_flush_work() up to the max depth of
chain (which will grow from 2 to 3 when ata discovery is moved to its own
discovery event). Instead of open coding multiple calls switch to use
drain_workqueue() to flush sas work.
drain_workqueue() does not handle new work submitted during the drain so
libsas needs a bit of infrastructure to hold off unchained work submissions
while a drain is in flight. A lldd ->notify() event is considered 'unchained'
while a sas_discover_event() is 'chained'. As Tejun notes:
"For now, I think it would be best to add private wrapper in libsas to
support deferring unchained work items while draining."
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In preparation for adding new states (SAS_HA_DRAINING, SAS_HA_FROZEN),
convert ha->state into a set of flags.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The locks only served to make sure the pending event bitmask was updated
consistently.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
These are never freed in the nominal path. A domain_device has a
different lifetime than a sas_rphy we need a dev->rphy independent way
of identifying sata devices.
Reviewed-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Arrange for the deallocation of a struct domain_device object when it no
longer has:
1/ any children
2/ references by any scsi_targets
3/ references by a lldd
The comment about domain_device lifetime in
Documentation/scsi/libsas.txt is stale as it appears mainline never had
a version of a struct domain_device that was registered as a kobject.
We now manage domain_device reference counts on behalf of external
agents.
Reviewed-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Per commit 3e4ec344 "libata: kill ATA_FLAG_DISABLED" needing to set
ATA_DEV_NONE is a holdover from before libsas converted to the
"new-style" ata-eh.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Commit 1e34c838 "[SCSI] libsas: remove spurious sata control register
read/write" removed the routines to fake the presence of the sata
control registers, now remove the unused data structure fields to kill
any remaining confusion.
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For the basic SCSI infrastructure files that are exporting symbols
but not modules themselves, add in the basic export.h header file
to allow the exports.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
port->dev_list maintains a list of devices attached to a given sas root port.
It needs to be mutated under a lock as contexts outside of the
single-threaded-libsas-workqueue access the list via sas_find_dev_by_rphy().
Fixup locations where the list was being mutated without a lock.
This is a follow-up to commit 5911e963 "[SCSI] libsas: remove expander
from dev list on error", where Luben noted [1]:
> 2/ We have unlocked list manipulations in sas_ex_discover_end_dev(),
> sas_unregister_common_dev(), and sas_ex_discover_end_dev()
Yes, I can see that and that is very unfortunate.
[1]: http://marc.info/?l=linux-scsi&m=131480962006471&w=2
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Allow the sas-transport-class to update events for local phys via a new
PHY_FUNC_GET_EVENTS command to ->lldd_control_phy(). Fixup drivers that
are not prepared for new enum phy_func values, and unify
->lldd_control_phy() error codes.
These are the SAS defined phy events that are reported in a
smp-report-phy-error-log command:
* /sys/class/sas_phy/<phyX>/invalid_dword_count
* /sys/class/sas_phy/<phyX>/running_disparity_error_count
* /sys/class/sas_phy/<phyX>/loss_of_dword_sync_count
* /sys/class/sas_phy/<phyX>/phy_reset_problem_count
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Based on original implementation from Jiangbi Liu and Maciej Trela.
ATAPI transfers happen in two-to-three stages. The two stage atapi
commands are those that include a dma data transfer. The data transfer
portion of these operations is handled by the hardware packet-dma
acceleration. The three-stage commands do not have a data transfer and
are handled without hardware assistance in raw frame mode.
stage1: transmit host-to-device fis to notify the device of an incoming
atapi cdb. Upon reception of the pio-setup-fis repost the task_context
to perform the dma transfer of the cdb+data (go to stage3), or repost
the task_context to transmit the cdb as a raw frame (go to stage 2).
stage2: wait for hardware notification of the cdb transmission and then
go to stage 3.
stage3: wait for the arrival of the terminating device-to-host fis and
terminate the command.
To keep the implementation simple we only support ATAPI packet-dma
protocol (for commands with data) to avoid needing to handle the data
transfer manually (like we do for SATA-PIO). This may affect
compatibility for a small number of devices (see
ATA_HORKAGE_ATAPI_MOD16_DMA).
If the data-transfer underruns, or encounters an error the
device-to-host fis is expected to arrive in the unsolicited frame queue
to pass to libata for disposition. However, in the DONE_UNEXP_FIS (data
underrun) case it appears we need to craft a response. In the
DONE_REG_ERR case we do receive the UF and propagate it to libsas.
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Libsas forget to set the sas_address and device type of rphy lead to file
under /sys/class/sas_x show wrong value, fix that.
Signed-off-by: Jack Wang <jack_wang@usish.com>
Tested-by: Crystal Yu <crystal_yu@usish.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The queue-depth for libsas-attached devices initializes to 32 and can
only be increased manually via sysfs to a max of 64, while mpt2sas
attached devices initialize to 254 and dynamically float via the
midlayer ->change_queue_depth interface.
No performance regression was observed with this change on the isci
driver.
Tested-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Pass queue_depth change requests to libata, and prevent queue_type
changes for ATA devices.
Otherwise:
1/ we do not honor the libata specific restrictions on the queue depth
2/ libsas drivers that do not set sdev->tagged_supported are unable to
change the queue_depth of ata devices via sysfs
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Allow expander table-to-table attachments for
expanders that support it.
Signed-off-by: Luben Tuikov <ltuikov@yahoo.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add SFF-8485 v0.7 / SAS-1 smp-write-gpio register support to libsas.
Defer SAS-2 support unless/until it defines an sgpio interface.
Minimum implementation needed to get the lights blinking.
try_test_sas_gpio_gp_bit() provides a common method to parse the
incoming write data (raw bitstream), and the to_sas_gpio_gp_bit() helper
routine can be used as a basis for the set/clear operations for the
'read' implementation. Host implementations parse as many bits
(ODx.[012]) as are locally supported and report the number of registers
successfully written. If the submitted data overruns the internal
number of registers available report the write as a success with the
number of bytes remaining reported in ->resid_len.
Example (assuming an active backplane) set the "identify" pattern for
the first 21 devices:
smp_write_gpio --count=2 --data=92,49,24,92,24,92,49,24 -t 4 --index=1 /dev/bsg/sas_hostX
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In an enclosure model where there are chaining expanders to a large body
of storage, it was discovered that libsas, responding to a broadcast
event change, would only revalidate the domain of first child expander
in the list.
The issue is that the pointer value to the discovered source device was
used to break out of the loop, rather than the content of the pointer.
This still remains non-compliant as the revalidate domain code is
supposed to loop through all child expanders, and not stop at the first
one it finds that reports a change count. However, the design of this
routine does not allow multiple device discoveries and that would be a
more complicated set of patches reserved for another day. We are fixing
the glaring bug rather than refactoring the code.
Signed-off-by: Mark Salyzyn <msalyzyn@us.xyratex.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
->queuecommand must return either 0, or one of the SCSI_MLQUEUE_* return
values. Non-transient errors are indicated by setting cmd->result before
calling ->scsi_done and returning 0. Fix libsas to adhere to this calling
convention. Note that the DID_ERROR for returns from the low-level driver
might not be correct for all cases, but it's the best we can do with
the current layering in libsas. I also suspect that the pre-existing
handling of -SAS_QUEUE_FULL should really be SCSI_MLQUEUE_HOST_BUSY, but
I'll leave that for a separate change.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Switch sas_queuecommand to a normal indentation and goto based error handling.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Now that isci has added a 3rd open coded user of this functionality just
share the libsas version.
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If expander discovery fails (sas_discover_expander()), remove the
expander from the port device list (sas_ex_discover_expander()),
before freeing it. Else the list is corrupted and, e.g., when we
attempt to send SMP commands to other devices, the kernel oopses.
Signed-off-by: Luben Tuikov <ltuikov@yahoo.com>
Cc: stable@kernel.org
Reviewed-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This allows a libsas driver to optionally provide a soft reset handler
for libata to drive. The isci driver allows software to control the
assertion/deassertion of SRST.
[jejb: checkpatch.pl fixes]
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Head off doomed-to-fail i/o in sas_queuecommand before sending it down
the ata path.
Before:
sd 7:0:0:0: [sdd] Synchronizing SCSI cache
ata8: no sense translation for status: 0x00
ata8: translated ATA stat/err 0x00/00 to SCSI SK/ASC/ASCQ 0xb/00/00
ata8.00: device reported invalid CHS sector 0
ata8: status=0x00 { }
ata8: no sense translation for status: 0x00
ata8: translated ATA stat/err 0x00/00 to SCSI SK/ASC/ASCQ 0xb/00/00
ata8.00: device reported invalid CHS sector 0
ata8: status=0x00 { }
ata8: no sense translation for status: 0x00
ata8: translated ATA stat/err 0x00/00 to SCSI SK/ASC/ASCQ 0xb/00/00
ata8.00: device reported invalid CHS sector 0
ata8: status=0x00 { }
sd 7:0:0:0: [sdd] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
sd 7:0:0:0: [sdd] Sense Key : Aborted Command [current] [descriptor]
sd 7:0:0:0: [sdd] Add. Sense: No additional sense information
sd 7:0:0:0: [sdd] Stopping disk
After:
sd 9:0:0:0: [sdd] Synchronizing SCSI cache
sd 9:0:0:0: [sdd] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
sd 9:0:0:0: [sdd] Stopping disk
sd 9:0:0:0: [sdd] START_STOP FAILED
sd 9:0:0:0: [sdd] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
This is a cosmetic change as sata i/o can still leak to a gone device,
but this addresses the nominal hotplug case when releasing the target.
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Commit 56dd2c06 "libsas: Don't issue commands to devices that have been
hot-removed" edited Darrick's original patch to remove setting 'gone' in
the sas_deform_port() path because that prevented scsi sync cache
commands from being issued when the driver was unloaded. However, this
allows true device gone notifications (as signaled port phy events) to
trigger sync cache commands to devices that are known to be unreachable.
Teach libsas which sas_deform_port() invocations are likely device gone
events.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Current version of libsas can not handle SATA NCQ error.
This patch handle SATA NCQ error as AHCI do.
Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
* 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6: (25 commits)
video: change to new flag variable
scsi: change to new flag variable
rtc: change to new flag variable
rapidio: change to new flag variable
pps: change to new flag variable
net: change to new flag variable
misc: change to new flag variable
message: change to new flag variable
memstick: change to new flag variable
isdn: change to new flag variable
ieee802154: change to new flag variable
ide: change to new flag variable
hwmon: change to new flag variable
dma: change to new flag variable
char: change to new flag variable
fs: change to new flag variable
xtensa: change to new flag variable
um: change to new flag variables
s390: change to new flag variable
mips: change to new flag variable
...
Fix up trivial conflict in drivers/hwmon/Makefile
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (170 commits)
[SCSI] scsi_dh_rdac: Add MD36xxf into device list
[SCSI] scsi_debug: add consecutive medium errors
[SCSI] libsas: fix ata list corruption issue
[SCSI] hpsa: export resettable host attribute
[SCSI] hpsa: move device attributes to avoid forward declarations
[SCSI] scsi_debug: Logical Block Provisioning (SBC3r26)
[SCSI] sd: Logical Block Provisioning update
[SCSI] Include protection operation in SCSI command trace
[SCSI] hpsa: fix incorrect PCI IDs and add two new ones (2nd try)
[SCSI] target: Fix volume size misreporting for volumes > 2TB
[SCSI] bnx2fc: Broadcom FCoE offload driver
[SCSI] fcoe: fix broken fcoe interface reset
[SCSI] fcoe: precedence bug in fcoe_filter_frames()
[SCSI] libfcoe: Remove stale fcoe-netdev entries
[SCSI] libfcoe: Move FCOE_MTU definition from fcoe.h to libfcoe.h
[SCSI] libfc: introduce __fc_fill_fc_hdr that accepts fc_hdr as an argument
[SCSI] fcoe, libfc: initialize EM anchors list and then update npiv EMs
[SCSI] Revert "[SCSI] libfc: fix exchange being deleted when the abort itself is timed out"
[SCSI] libfc: Fixing a memory leak when destroying an interface
[SCSI] megaraid_sas: Version and Changelog update
...
Fix up trivial conflicts due to whitespace differences in
drivers/scsi/libsas/{sas_ata.c,sas_scsi_host.c}
Replace EXTRA_CFLAGS with ccflags-y.
Signed-off-by: matt mooney <mfm@muteddisk.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
I think this stems from a misunderstanding of how the ata error handler
works. ata_scsi_cmd_error_handler() gets called with a passed in list
of commands to handle. However, that list may still not be empty when
it exits. The command ata_scsi_port_error_handler() must be called
(which takes no list) before the list will be completely emptied. This
bites the sas error handler because the two are called from different
functions and the original list has gone out of scope before
ata_scsi_port_error_handler() is called. leading to some commands
dangling on bare stack, which is a potential memory corruption issue.
Fix this by manually deleting all outstanding commands from the on-stack
list before it goes out of scope.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
All checks of ATA_FLAG_NO_LEGACY have been removed by the commits
c791c30670 ([libata] minor PCI IDE probe
fixes and cleanups) and f0d36efdc6 (libata:
update libata core layer to use devres), so I think it's time to finally
get rid of this flag...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 0d5ff56677 (libata: convert to iomap)
removed all checks of ATA_FLAG_MMIO but neglected to remove the flag itself.
Do it now, at last...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
These flags are marked as obsolete and the checks for them have been removed
by commit 294440887b (libata-sff: kill unused
ata_bus_reset()), so I think it's time to finally get rid of them...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 14bdef982c ([libata] convert drivers to
use ata.h mode mask defines) didn't convert these two libata driver outside
drivers/ata/...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The conversion is quite complex given that the libata new error
handler has to be hooked into the current libsas timeout and error
handling. The way this is done is to process all the failed commands
via libsas first, but if they have no underlying sas task (and they're
on a sata device) assume they are destined for the libata error
handler and send them accordingly.
Finally, activate the port recovery of the libata error handler for
each port known to the host. This is somewhat suboptimal, since that
port may not need recovering, but given the current architecture of
the libata error handler, it's the only way; and the spurious
activation is harmless.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
In some test envirenment, there is loopback topology test. We should
handle this during discovery.
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The conversion is quite complex given that the libata new error
handler has to be hooked into the current libsas timeout and error
handling. The way this is done is to process all the failed commands
via libsas first, but if they have no underlying sas task (and they're
on a sata device) assume they are destined for the libata error
handler and send them accordingly.
Finally, activate the port recovery of the libata error handler for
each port known to the host. This is somewhat suboptimal, since that
port may not need recovering, but given the current architecture of
the libata error handler, it's the only way; and the spurious
activation is harmless.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Originally, libata required the illusion that it could access the sata
control register. Now, however, it can run perfectly well without
them, so remove the dummy routines from libsas which tried to emulate
them (but only ended up causing confusion).
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
ATAPI check condition needs to be treated the same as a success or
protocol return. The register returns from the PACKET command are all
correctly positioned in the device to host register FIS and so we
should collect them properly. Right at the moment this doesn't matter
because libata sends a request sense always for ATAPI errors, but if
it ever checked the registers, we should have the correct contents
just in case.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
libsas makes use of scsi_schedule_eh() but forgets to clear the
host_eh_scheduled flag in its error handling routine. Because of this,
the error handler thread never gets to sleep; it's constantly awake and
trying to run the error routine leading to console spew and inability to
run anything else (at least on a UP system). The fix is to clear the
flag as we splice the work queue.
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
To date libsas has only looked at the attached sas address when
determining the formation of wide ports. The specification and some
hardware expects that phys with different addresses will not form a wide
port unless the local peer phys also match each other. Introduce a flag
to select stricter behavior at sas_register_ha() time. The flag can be
dropped once it is known that all libsas users expect the same behavior.
Current drivers just initialize this field to zero and get the
traditional behavior.
Reported-by: Patrick Thomson <patrick.s.thomson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Move the mid-layer's ->queuecommand() invocation from being locked
with the host lock to being unlocked to facilitate speeding up the
critical path for drivers who don't need this lock taken anyway.
The patch below presents a simple SCSI host lock push-down as an
equivalent transformation. No locking or other behavior should change
with this patch. All existing bugs and locking orders are preserved.
Additionally, add one parameter to queuecommand,
struct Scsi_Host *
and remove one parameter from queuecommand,
void (*done)(struct scsi_cmnd *)
Scsi_Host* is a convenient pointer that most host drivers need anyway,
and 'done' is redundant to struct scsi_cmnd->scsi_done.
Minimal code disturbance was attempted with this change. Most drivers
needed only two one-line modifications for their host lock push-down.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fix bug reported by Chuck. And this new version incorporate comments
from Hannes. Please consider to include it into mainline.
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Lindar Liu <lindar_liu@usish.com>
Tested-by: Chuck Tuffli <Chuck_Tuffli@pmc-sierra.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
sd will get hung up issuing commands to flush write cache if a SAS
device behind the expander is unplugged without warning. Change libsas
to reject commands to domain devices that have already gone away.
[maciej.trela@intel.com: removed setting ->gone in sas_deform_port() to
permit sync cache commands at module removal]
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Tested-by: Haipao Fan <haipao.fan@intel.com>
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Some cards (like mvsas) have issue troubles if non-NCQ commands are
mixed with NCQ ones. Fix this by using the libata default NCQ check
routine which waits until all NCQ commands are complete before issuing
a non-NCQ one. The impact to cards (like aic94xx) which don't need
this logic should be minimal
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
REQ_HARDBARRIER is deprecated. Remove spurious uses in the following
users. Please note that other than osdblk, all other uses were
already spurious before deprecation.
* osdblk: osdblk_rq_fn() won't receive any request with
REQ_HARDBARRIER set. Remove the test for it.
* pktcdvd: use of REQ_HARDBARRIER in pkt_generic_packet() doesn't mean
anything. Removed.
* aic7xxx_old: Setting MSG_ORDERED_Q_TAG on REQ_HARDBARRIER is
spurious. Removed.
* sas_scsi_host: Setting TASK_ATTR_ORDERED on REQ_HARDBARRIER is
spurious. Removed.
* scsi_tcq: The ordered tag path wasn't being used anyway. Removed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Boaz Harrosh <bharrosh@panasas.com>
Cc: James Bottomley <James.Bottomley@suse.de>
Cc: Peter Osterlund <petero2@telia.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
We have two separate definitions for identical constants with nearly the
same name. One comes from the generic headers in scsi.h; the other is
an enum in libsas.h ... it's causing confusion about which one is
correct (fortunately they both are).
Fix this by eliminating the libsas.h duplicate
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (182 commits)
[SCSI] aacraid: add an ifdef'd device delete case instead of taking the device offline
[SCSI] aacraid: prohibit access to array container space
[SCSI] aacraid: add support for handling ATA pass-through commands.
[SCSI] aacraid: expose physical devices for models with newer firmware
[SCSI] aacraid: respond automatically to volumes added by config tool
[SCSI] fcoe: fix fcoe module ref counting
[SCSI] libfcoe: FIP Keep-Alive messages for VPorts are sent with incorrect port_id and wwn
[SCSI] libfcoe: Fix incorrect MAC address clearing
[SCSI] fcoe: fix a circular locking issue with rtnl and sysfs mutex
[SCSI] libfc: Move the port_id into lport
[SCSI] fcoe: move link speed checking into its own routine
[SCSI] libfc: Remove extra pointer check
[SCSI] libfc: Remove unused fc_get_host_port_type
[SCSI] fcoe: fixes wrong error exit in fcoe_create
[SCSI] libfc: set seq_id for incoming sequence
[SCSI] qla2xxx: Updates to ISP82xx support.
[SCSI] qla2xxx: Optionally disable target reset.
[SCSI] qla2xxx: ensure flash operation and host reset via sg_reset are mutually exclusive
[SCSI] qla2xxx: Silence bogus warning by gcc for wrap and did.
[SCSI] qla2xxx: T10 DIF support added.
...
ATA_FLAG_DISABLED is only used by drivers which don't use
->error_handler framework and is largely broken. Its only meaningful
function is to make irq handlers skip processing if the flag is set,
which is largely useless and even harmful as it makes those ports more
likely to cause IRQ storms.
Kill ATA_FLAG_DISABLED and makes the callers disable attached devices
instead. ata_port_probe() and ata_port_disable() which manipulate the
flag are also killed.
This simplifies condition check in IRQ handlers. While updating IRQ
handlers, remove ap NULL check as libata guarantees consecutive port
allocation (unoccupied ports are initialized with dummies) and
long-obsolete ATA_QCFLAG_ACTIVE check (checked by ata_qc_from_tag()).
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
commit 70b25f890c
Author: Tejun Heo <tj@kernel.org>
Date: Thu Apr 15 09:00:08 2010 +0900
[SCSI] fix locking around blk_abort_request()
Introduced a reference before check problem, fix this by moving the
lock shorthand code to be right at the point of actual use.
Reported-by: Dan Carpenter <error27@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
blk_abort_request() expects queue lock to be held by the caller.
Grab it before calling the function.
Lack of this synchronization led to infinite loop on corrupt
q->timeout_list.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (222 commits)
[SCSI] zfcp: Remove flag ZFCP_STATUS_FSFREQ_TMFUNCNOTSUPP
[SCSI] zfcp: Activate fc4s attributes for zfcp in FC transport class
[SCSI] zfcp: Block scsi_eh thread for rport state BLOCKED
[SCSI] zfcp: Update FSF error reporting
[SCSI] zfcp: Improve ELS ADISC handling
[SCSI] zfcp: Simplify handling of ct and els requests
[SCSI] zfcp: Remove ZFCP_DID_MASK
[SCSI] zfcp: Move WKA port to zfcp FC code
[SCSI] zfcp: Use common code definitions for FC CT structs
[SCSI] zfcp: Use common code definitions for FC ELS structs
[SCSI] zfcp: Update FCP protocol related code
[SCSI] zfcp: Dont fail SCSI commands when transitioning to blocked fc_rport
[SCSI] zfcp: Assign scheduled work to driver queue
[SCSI] zfcp: Remove STATUS_COMMON_REMOVE flag as it is not required anymore
[SCSI] zfcp: Implement module unloading
[SCSI] zfcp: Merge trace code for fsf requests in one function
[SCSI] zfcp: Access ports and units with container_of in sysfs code
[SCSI] zfcp: Remove suspend callback
[SCSI] zfcp: Remove global config_mutex
[SCSI] zfcp: Replace local reference counting with common kref
...
This patch modifies scsi_host_template->change_queue_depth so that
it takes an argument indicating why it is being called. This will be
used so that if a LLD needs to do some extra processing when
handling queue fulls or later ramp ups, it can do so.
This is a simple port of the drivers setting a change_queue_depth
callback. In the patch I just have these LLDs adjust the queue depth
if the user was requesting it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
[Vasu.Dev: v2
Also converted pmcraid_change_queue_depth and then verified
all modules compile using "make allmodconfig" for any new build
warnings on X86_64.
Updated original description after combing two original
patches from Mike to make this patch git bisectable.]
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
[jejb: fixed up 53c700]
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
We should not set res to 0 in function sas_ex_discover_dev in order to let
it discover it further when wide port hotplug in .
Signed-off-by: Tom Peng <tom_peng@usish.com>
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Hotplug of phys which form wide ports simply does not work at the moment. Fix
this by adding checks at the hotplug points to see if the attached sas address
of the phy already exists (in which case it's part of a wide port) and act
accordingly.
Signed-off-by: Tom Peng <tom_peng@usish.com>
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Lindar Liu <lindar_liu@usish.com>
Signed-off-by: Kevin Ao <aoqingyun@usish.com>
[jejb: tidied up coding, fixed an error case and made TRUE/FALSE lower
case to fix a ppc64 compile error in linux-next]
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There's a hotplug problem in the way libsas allocates ports: it loops over the
available ports first trying to add to an existing for a wide port and
otherwise allocating the next free port. This scheme only works if the port
array is packed from zero, which fails if a port gets hot unplugged and the
array becomes sparse. In that case, a new port is formed even if there's a
wide port it should be part of. Fix this by creating two loops over all the
ports: the first to see if the phy should be part of a wide port and the
second to form a new port in an empty port slot.
Signed-off-by: Tom Peng <tom_peng@usish.com>
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Lindar Liu <lindar_liu@usish.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In commit c3a4d78c58, while introducing
rq->resid_len, the default value of residue count was changed from
full count to zero. The conversion was done under the assumption that
when a request fails residue count wasn't defined. However, Boaz and
James pointed out that this wasn't true and the residue count should
be preserved for failed requests too.
This patchset restores the original behavior by setting rq->resid_len
to blk_rq_bytes(rq) on request start and restoring explicit clearing
in affected drivers. While at it, take advantage of the fact that
rq->resid_len is set to full count where applicable.
* ide-cd: rq->resid_len cleared on pc success
* mptsas: req->resid_len cleared on success
* sas_expander: rsp/req->resid_len cleared on success
* mpt2sas_transport: req->resid_len cleared on success
* ide-cd, ide-tape, mptsas, sas_host_smp, mpt2sas_transport, ub: take
advantage of initial full count to simplify code
Boaz Harrosh spotted bug in resid_len initialization. Fixed as
suggested.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Borislav Petkov <petkovbb@googlemail.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
With recent unification of fields, it's now guaranteed that
rq->data_len always equals blk_rq_bytes(). Convert all non-IDE direct
users to accessors. IDE will be converted in a separate patch.
Boaz: spotted incorrect data_len/resid_len conversion in osd.
[ Impact: convert direct rq->data_len usages to blk_rq_bytes() ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
rq->data_len served two purposes - the length of data buffer on issue
and the residual count on completion. This duality creates some
headaches.
First of all, block layer and low level drivers can't really determine
what rq->data_len contains while a request is executing. It could be
the total request length or it coulde be anything else one of the
lower layers is using to keep track of residual count. This
complicates things because blk_rq_bytes() and thus
[__]blk_end_request_all() relies on rq->data_len for PC commands.
Drivers which want to report residual count should first cache the
total request length, update rq->data_len and then complete the
request with the cached data length.
Secondly, it makes requests default to reporting full residual count,
ie. reporting that no data transfer occurred. The residual count is
an exception not the norm; however, the driver should clear
rq->data_len to zero to signify the normal cases while leaving it
alone means no data transfer occurred at all. This reverse default
behavior complicates code unnecessarily and renders block PC on some
drivers (ide-tape/floppy) unuseable.
This patch adds rq->resid_len which is used only for residual count.
While at it, remove now unnecessasry blk_rq_bytes() caching in
ide_pc_intr() as rq->data_len is not changed anymore.
Boaz : spotted missing conversion in osd
Sergei : spotted too early conversion to blk_rq_bytes() in ide-tape
[ Impact: cleanup residual count handling, report 0 resid by default ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Doug Gilbert <dgilbert@interlog.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
for SAS drivers.
Caught by Ke Wei (and team?) at Marvell.
Also, move the ata_scsi_ioctl export to libata-scsi.c, as that seems to be the
general trend.
Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
[jejb: limit ioctl to returning 20 characters to avoid overrun
on long device names and add a few more conversions]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* 'for-2.6.28' of git://git.kernel.dk/linux-2.6-block: (132 commits)
doc/cdrom: Trvial documentation error, file not present
block_dev: fix kernel-doc in new functions
block: add some comments around the bio read-write flags
block: mark bio_split_pool static
block: Find bio sector offset given idx and offset
block: gendisk integrity wrapper
block: Switch blk_integrity_compare from bdev to gendisk
block: Fix double put in blk_integrity_unregister
block: Introduce integrity data ownership flag
block: revert part of d7533ad0e132f92e75c1b2eb7c26387b25a583c1
bio.h: Remove unused conditional code
block: remove end_{queued|dequeued}_request()
block: change elevator to use __blk_end_request()
gdrom: change to use __blk_end_request()
memstick: change to use __blk_end_request()
virtio_blk: change to use __blk_end_request()
blktrace: use BLKTRACE_BDEV_SIZE as the name size for setup structure
block: add lld busy state exporting interface
block: Fix blk_start_queueing() to not kick a stopped queue
include blktrace_api.h in headers_install
...
Right now SCSI and others do their own command timeout handling.
Move those bits to the block layer.
Instead of having a timer per command, we try to be a bit more clever
and simply have one per-queue. This avoids the overhead of having to
tear down and setup a timer for each command, so it will result in a lot
less timer fiddling.
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Logically, SCR access ops should take @link; however, there was no
compelling reason to convert all SCR access ops when adding @link
abstraction as there's one-to-one mapping between a port and a non-PMP
link. However, that assumption won't hold anymore with the scheduled
addition of slave link.
Make SCR access ops per-link.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
[jejb: fixed up a ton of missed conversions.
All of you are on notice this has happened, driver trees will now
need to be rebased]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: SCSI List <linux-scsi@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (137 commits)
[SCSI] iscsi: bidi support for iscsi_tcp
[SCSI] iscsi: bidi support at the generic libiscsi level
[SCSI] iscsi: extended cdb support
[SCSI] zfcp: Fix error handling for blocked unit for send FCP command
[SCSI] zfcp: Remove zfcp_erp_wait from slave destory handler to fix deadlock
[SCSI] zfcp: fix 31 bit compile warnings
[SCSI] bsg: no need to set BSG_F_BLOCK bit in bsg_complete_all_commands
[SCSI] bsg: remove minor in struct bsg_device
[SCSI] bsg: use better helper list functions
[SCSI] bsg: replace kobject_get with blk_get_queue
[SCSI] bsg: takes a ref to struct device in fops->open
[SCSI] qla1280: remove version check
[SCSI] libsas: fix endianness bug in sas_ata
[SCSI] zfcp: fix compiler warning caused by poking inside new semaphore (linux-next)
[SCSI] aacraid: Do not describe check_reset parameter with its value
[SCSI] aacraid: Fix down_interruptible() to check the return value
[SCSI] sun3_scsi_vme: add MODULE_LICENSE
[SCSI] st: rename flush_write_buffer()
[SCSI] tgt: use KMEM_CACHE macro
[SCSI] initio: fix big endian problems for auto request sense
...
Now that SFF assumptions are separated out from non-SFF reset
sequence, port_ops->sff_dev_select() is no longer necessary for
non-SFF controllers. Kill ata_noop_dev_select() and ->sff_dev_select
initialization from base and other non-SFF port_ops.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Now that all SFF stuff is separated out of core layer, core layer
doesn't call ops->[alt_]check_status(). In fact, no one calls them
for non-SFF drivers anymore. Kill them.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Now that all SFF stuff is separated out of core layer, core layer
doesn't call ops->tf_read directly. It gets called only via
ops->qc_fill_rtf() for non-SFF drivers. This patch directly
implements private ops->qc_fill_rtf() for non-SFF controllers and kill
ops->tf_read().
This is much cleaner for non-SFF controllers as some of them have to
cache SFF register values in private data structure and report the
cached values via ops->tf_read(). Also, ops->tf_read() gets nasty for
controllers which don't have clear notion of TF registers when
operation is not in progress.
As this change makes default ops->qc_fill_rtf unnecessary, move
ata_sff_qc_fill_rtf() form ata_base_port_ops to ata_sff_port_ops where
it belongs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
On command completion, ata_qc_complete() directly called ops->tf_read
to fill qc->result_tf. This patch adds ops->qc_fill_rtf to replace
hardcoded ops->tf_read usage.
ata_sff_qc_fill_rtf() which uses ops->tf_read to fill result_tf is
implemented and set in ata_base_port_ops and other ops tables which
don't inherit from ata_base_port_ops, so this patch doesn't introduce
any behavior change.
ops->qc_fill_rtf() is similar to ops->sff_tf_read() but can only be
called when a command finishes. As some non-SFF controllers don't
have TF registers defined unless they're associated with in-flight
commands, this limited operation makes life easier for those drivers
and help lifting SFF assumptions from libata core layer.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Add sff_ prefix to SFF specific port ops.
This rename is in preparation of separating SFF support out of libata
core layer. This patch strictly renames ops and doesn't introduce any
behavior difference.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Provide a facility to use the request_firmware() interface to get a SAS
address from userspace. This can be used by SAS LLDDs that cannot
obtain the address from the host adapter.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We give a very cryptic error if an ATA device is seen on a SAS port
but libsas isn't compiled to include libata to handle them. Add an
extra warning to explain specifically what the problem is.
Acked-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- Correct one use after free of the sas task
- update the reset required path to move straight to LUN reset
- make the bigger hammer actually reset something instead of just trying
to clear all the tasks.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Once the phy reset is plumbed in properly, SATA error handling fails
nastily because we change the port attached_sas_address using the WWN
field of the IDENTIFY message. This is a nice thing to do in theory,
but it really destroys hotplug because any event on the port causes an
automatic mismatch between the sas_address the phy just picked up and
the one we propagate into the port. However ugly they are, we have to
stick with the sas addresses made up by the phys and expanders.
Also does a few cosmetic changes to the way port printing is done to
make it clearer how a port is formed.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This is needed by the to be added I_T reset function in aic94xx. It
needs to know the local phy so it can send a link or hard reset along
the path.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Dan Williams