In amd64_edac_init(void) in amd64_edac.c, cache_k8_northbridges() is
called before pci_register_driver. If it fails, should exit with err
directly.
Signed-off-by: Li Hong <lihong.hi@gmail.com>
Acked-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Allow csrows to properly initialize when the topology only has active
channels on 2 and 3. This new check allows proper detection and
initialization in this topology. Only checking the first mrt that
represented channels 0 and 1 is not sufficient.
I also fixed up the related debug information path. I can submit as a 2nd
patch if needed.
Signed-off-by: Keith Mannthey <kmannth@us.ibm.com>
Acked-by: Aristeu Rozanski <aris@ruivo.org>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When building without CONFIG_PCI the edac_pci_idx variable is unused,
causing a build-time warning. Wrap the variable in #ifdef CONFIG_PCI,
just like the rest of the PCI support.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The i5400 EDAC driver has several bugs with chip-select row computation
which most likely lead to bugs in detailed error reporting. Attempts to
contact the authors have gone mostly unanswered so I am presenting my diff
here. I do not subscribe to lkml and would appreciate being kept in the
cc.
The most egregious problem was miscalculating the addresses of MTR
registers after register 0 by assuming they are 32bit rather than 16.
This caused the driver to miss half of the memories. Most motherboards
tend to have only 8 dimm slots and not 16, so this may not have been
noticed before.
Further, the row calculations multiplied the number of dimms several
times, ultimately ending up with a maximum row of 32. The chipset only
supports 4 dimms in each of 4 channels, so csrow could not be higher than
4 unless you use a row per-rank with dual-rank dimms. I opted to
eliminate this behavior as it is confusing to the user and the error
reporting works by slot and not rank. This gives a much clearer view of
memory by slot and channel in /sys.
Signed-off-by: Jeff Roberson <jroberson@jroberson.net>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add an atomic notifier which ensures proper locking when conveying
MCE info to EDAC for decoding. The actual notifier call overrides a
default, negative priority notifier.
Note: make sure we register the default decoder only once since
mcheck_init() runs on each CPU.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <20091003065752.GA8935@liondog.tnic>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When injecting DRAM ECC errors (F3xBC_x8), EccVector[15:0] is a bitmask
of which bits should be error injected when written to and holds the
payload of 16-bit DRAM word when read, respectively.
Add /sysfs members to show the DRAM ECC section/word/vector.
Fail wrong injection values entered over /sysfs instead of truncating
them.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
On Fam10h and above, F1x[1, 0][7C:40] are DRAM Base/Limit registers
which specify the destination node of a DRAM address. Those address
boundaries are being extracted into ->dram_base[] and ->dram_limit[].
Correct the extraction masks to match the respective address bits.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Different processor families support a different number of chip selects.
Handle this in a family-dependent way with the proper values assigned at
init time (see amd64_set_dct_base_and_mask).
Remove _DCSM_COUNT defines since they're used at one place and originate
from public documentation.
CC: Keith Mannthey <kmannth@us.ibm.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
This allows the errors to be further decoded and mapped to csrows.
Tested with ECC debug dimms and an Rev F cpu based system.
Signed-off-by: Keith Mannthey <kmannth@us.ibm.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The check when DRAM interleaving is enabled should be done against the
pvt->dram_IntlvSel field and not against the ->dram_limit.
Simplify first loop and fixup printk formatting while at it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The pvt->dram_IntlvEn saves the 3 "Interleave Enable" bits already
right-shifted by 8 so the check in find_mc_by_sys_addr() by shifting the
values to the left 8 bits is wrong.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
K8 DRAM base and limit addresses from F1x40 +8*i and F1x44 + 8*i, where
i in (0..7) are both bits 39-24 and therefore the shifting should be
done by 24 and not by 8.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Allocate memory statically for 8-node machines max for simplicity
instead of relying on MAX_NUMNODES which is 0 on !CONFIG_NUMA builds.
Spotted by Jan Beulich.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
This converts the MCE decoding logic into a standalone config
option which can be built-in or a module, the first one being the
default for MCEs happening early on in the boot process.
This, beyond being separated in a cleaner way, also saves RAM by
making the decoding logic modular.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andi Kleen <andi@firstfloor.org>
LKML-Reference: <20091002133148.GD28682@aftab>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Make decoding of MCEs happen only on AMD hardware by registering a
non-default callback only on CPU families which support it.
While looking at the interaction of decode_mce() with the other MCE
code i also noticed a few other things and made the following
cleanups/fixes:
- Fixed the mce_decode() weak alias - a weak alias is really not
good here, it should be a proper callback. A weak alias will be
overriden if a piece of code is built into the kernel - not
good, obviously.
- The patch initializes the callback on AMD family 10h and 11h.
- Added the more correct fallback printk of:
No support for human readable MCE decoding on this CPU type.
Transcribe the message and run it through 'mcelog --ascii' to decode.
On CPUs that dont have a decoder.
- Made the surrounding code more readable.
Note that the callback allows us to have a default fallback -
without having to check the CPU versions during the printout
itself. When an EDAC module registers itself, it can install the
decode-print function.
(there's no unregister needed as this is core code.)
version -v2 by Borislav Petkov:
- add K8 to the set of supported CPUs
- always build in edac_mce_amd since we use an early_initcall now
- fix checkpatch warnings
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andi Kleen <andi@firstfloor.org>
LKML-Reference: <20091001141432.GA11410@aftab>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Module edac_core.ko uses call_rcu() callbacks in edac_device.c, edac_mc.c
and edac_pci.c.
They all use a wait_for_completion() scheme, but this scheme it not 100%
safe on multiple CPUs. See the _rcu_barrier() implementation which
explains why extra precausion is needed.
The patch adds a comment about rcu_barrier() and as a precausion calls
rcu_barrier(). A maintainer needs to look at removing the
wait_for_completion code.
[dougthompson@xmission.com: remove the wait_for_completion code]
Signed-off-by Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A driver for the Intel 3200 and 3210 memory controllers. It has only had
light testing so far, and currently makes no attempt to decode error
addresses at anything finer than csrow granularity.
Signed-off-by: Jason Uhlenkott <juhlenko@akamai.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the function resource_size, which reduces the chance of introducing
off-by-one errors in calculating the resource size.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
struct resource *res;
@@
- (res->end - res->start) + 1
+ resource_size(res)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the Freescale MPC83xx memory controller to the existing
driver for the Freescale MPC85xx memory controller. The only difference
between the two processors are in the CS_BNDS register parsing code, which
has been changed so it will work on both processors.
The L2 cache controller does not exist on the MPC83xx, but the OF
subsystem will not use the driver if the device is not present in the OF
device tree.
I had to change the nr_pages calculation to make the math work out. I
checked it on my board and did the math by hand for a 64GB 85xx using 64K
pages. In both cases, nr_pages * PAGE_SIZE comes out to the correct
value.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Based on Kumar's new compatible types patch, add P2020 into MPC85xx EDAC
compatible lists so that EDAC can recognize P2020 meomry controller and L2
cache controller and export the relevant fields to sysfs.
EDAC MPC85xx DDR3 support is needed if DDR3 memory stick is installed on a
P2020DS board so that EDAC core can recognize DDR3 memory type.
Signed-off-by: Yang Shi <yang.shi@windriver.com>
Acked-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The old code was using smp_call_function_many which skips the current
cpu if it is in the supplied cpumask. Switch to the rdmsr_on_cpus()
interface which takes care of that.
In addition, add get_cpus_on_this_dct_cpumask helper which computes a
cpumask of all the cores on a node and thus on a DCT.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Simplify the procedure by checking if there is any DIMM in each channel.
This patch will fix the bugs such as when there is no DIMMs under
certain node, two DIMMs in the same channel, and only one DIMM in each
channel of the node.
Borislav: minor fixups
Signed-off-by: Wan Wei <wanwei@mail.dawning.com.cn>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Simplify code flow and make sure return value is always valid since
further driver init depends on it. Carve out long warning string and
make code more readable. Shorten some names, while at it.
There should be no functional change resulting from this patch.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
-tip testing found the following build failure (config attached):
drivers/built-in.o: In function `amd64_check':
amd64_edac.c:(.text+0x3e9491): undefined reference to `amd_decode_nb_mce'
drivers/built-in.o: In function `amd64_init_2nd_stage':
amd64_edac.c:(.text+0x3e9b46): undefined reference to `amd_report_gart_errors'
amd64_edac.c:(.text+0x3e9b55): undefined reference to `amd_register_ecc_decoder'
drivers/built-in.o: In function `amd64_nbea_store':
amd64_edac_dbg.c:(.text+0x3ea22e): undefined reference to `amd_decode_nb_mce'
drivers/built-in.o: In function `amd64_remove_one_instance':
amd64_edac.c:(.devexit.text+0x3eea): undefined reference to `amd_report_gart_errors'
amd64_edac.c:(.devexit.text+0x3ef6): undefined reference to `amd_unregister_ecc_decoder'
the AMD EDAC code has a dependency on CONFIG_CPU_SUP_AMD facilities. The
patch below solves the problem here.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Those get reported in MC0_STATUS, see Table 92, F10h BKDG (31116, rev.
3.28) for more details.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
This is the MCE error code from the MCi_STATUS banks, bits [15:0] which
describe what type of error was encountered: GART TLB, Memory or Bus
error. The semantics of those bits are identical across all MCE banks so
decode those separately, irrespectively of MCE type.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The MCi_STATUS registers have most field definitions in common so decode
them in the general path. Do not pass ecc_type along and compute it in
__amd64_decode_bus_error instead.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Move NB decoder along with required defines to EDAC MCE core. Add
registration routines for further decoding of the MCE info in the AMD64
EDAC module.
CC: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
This is in preparation of adding AMD-specific MCE decoding functionality
to the EDAC core. The error decoding macros originate from the AMD64
EDAC driver albeit in a simplified and cleaned up version here.
While at it, add macros to generate the error description strings and
use them in the error type decoders directly which removes a bunch of
code and makes the decoding functions much more readable. Also, fix
strings and shorten macro names.
Remove superfluous htlink_msgs.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
On the good path of BIOS enabled ECC and no override, the value returned
is 1 by omission and thus is deemed failing by the probe-function.
Allow proper module initialization by clearing the retval explicitly.
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Intel X38 MCHBAR is a 64bits register, base from 0x48, so its higher base
is 0x4C.
Signed-off-by: Lu Zhihe <tombowfly@gmail.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: <stable@kernel.org> [2.6.30.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since some new MPC85xx SOCs support DDR3 memory now, so add DDR3 memory
type for MPC85xx EDAC.
Signed-off-by: Yang Shi <yang.shi@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
amd64_check_ecc_enabled() returns non-zero status when ECC
checking/correcting is disabled and this fails further loading of the
driver even when 'ecc_enable_override' boot param is used.
Fix that by clearing return status in that case.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Checking whether the machine is using ECC enabled DRAM is done through
testing the DimmEccEn bit in the DRAM Cfg Low register (F2x[1,0]90). Do
that instead of testing all bits from the DimmEccEn upwards.
Also, remove mci->edac_cap assignment and use value returned from
amd64_determine_edac_cap().
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The remove function uses __devexit, so the .remove assignment needs
__devexit_p() to fix a build error with hotplug disabled.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add edac_device_alloc_index(), because for MAPLE platform there may
exist several EDAC driver modules that could make use of
edac_device_ctl_info structure at the same time. The index allocation
for these structures should be taken care of by EDAC core.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce IBM CPC925 EDAC driver, which makes use of ECC, CPU and
HyperTransport Link error detections and corrections on the IBM
CPC925 Bridge and Memory Controller.
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prevent EDAC compilation units from being built by default and let the
user explicitly select the needed modules.
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Tested-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
While at it, fix a link failure when !K8_NB.
Acked-by: Doug Thompson <dougthompson@xmission.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Tested-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Also, link into Kbuild by adding Kconfig and Makefile entries.
Borislav:
- Kconfig/Makefile splitting
- use zero-sized arrays for the sysfs attrs if not enabled
- rename sysfs attrs to more conform values
- shorten CONFIG_ names
- make multiple structure members assignment vertically aligned
- fix/cleanup comments
- fix function return value patterns
- fix err labels
- fix a memleak bug caught by Ingo
- remove the NUMA dependency and use num_k8_northbrides for initializing
a driver instance per NB.
- do not copy the pvt contents into the mci struct in
amd64_init_2nd_stage() and save it in the mci->pvt_info void ptr
instead.
- cleanup debug calls
- simplify amd64_setup_pci_device()
Reviewed-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav:
- convert to the new {rd|wr}msr_on_cpus interfaces.
- convert pvt->old_mcgctl to a bitmask thus saving some bytes
- fix/cleanup comments
- fix function return value patterns
- add a proper bugfix found by Doug to amd64_check_ecc_enabled where we
missed checking for the ECC enabled bit in NB CFG.
- cleanup debug calls
Reviewed-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav:
- compute dct_sel_base_off in f10_match_to_this_node() correctly since
it cannot be assumed that the Reserved bits are zero and they have to be
masked out instead.
- cleanup, remove StinkyIdentifiers, simplify logic
- fix function return value patterns
- cleanup debug calls
Reviewed-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav:
- fix a wrong negation in f10_determine_base_addr_offset()
- fix a wrong mask in f10_determine_base_addr_offset() which should
select DctSelBaseAddr[31:11] and not [31:16] as it was before
- remove StinkyIdentifiers, trivially simplify code.
- fix/cleanup comments
- fix function return value patterns
Reviewed-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav:
Fail f10_early_channel_count() if error encountered while reading a NB
register since those cached register contents are accessed afterwards.
- fix/cleanup comments
- fix function return value patterns
- cleanup debug calls
Reviewed-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav:
- rename sysfs attrs to more conform names
- cleanup/fix comments according to BKDG text
- fix function return value patterns
- cleanup debug calls
Reviewed-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
This is for dumping different registers and testing the address mapping
logic using the ECC syndromes.
Borislav:
- split sysfs attrs per file
- use more conform names for the sysfs attrs
- fix function return value patterns
- cleanup/fix comments
- cleanup debug calls
Reviewed-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The amd8111_edac.c driver will fail allmodconfig on architectures other
than PPC, introduce Kconfig dependency to avoid this, since both AMD8111
and AMD8131 chips are only adopted on Maple so far.
Signed-off-by: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The "bus_id" member in the device structure has been obsolete, use
dev_name() instead.
Signed-off-by: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Error found by Jeff Haran.
The error detect register is 0s when no errors are detected. The check
code is incorrect, so reverse check sense.
Reported-by: Jeff Haran <jharan@Brocade.COM>
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The edac-core driver includes code which assumes that the work_struct
which is included in every delayed_work is the first member of that
structure. This is currently the case but might change in the future, so
use to_delayed_work() instead, which doesn't make such an assumption.
linux-2.6.30-rc1 has the to_delayed_work() function that will allow this
patch to work
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the edac local pci_write_bits32 to properly note the 'escape' mask if
all ones in a 32-bit word.
Currently no consumer of this function uses that mask, so there is no
danger to existing code.
Signed-off-by: Jeff Haran <jharan@Brocade.COM>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce AMD8131 EDAC driver source file, which makes use of error
detections on the PCI-X Bridge Controllers on the AMD8131 HyperTransport
PCI-X Tunnel.
Signed-off-by: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce AMD8131 EDAC driver header file, which adds register and bits
definitions for the PCI-X Bridge Controller on the AMD8131 HyperTransport
I/O Hub.
Signed-off-by: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add edac_pci_alloc_index(), because for MAPLE platform there may exist
several EDAC driver modules that could make use of edac_pci_ctl_info
structure at the same time. The index allocation for these structures
should be taken care of by EDAC core.
Signed-off-by: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce AMD8111 EDAC driver source file, which makes use of error
detections on the LPC Bridge Controller and PCI Bridge Controller on the
AMD8111 HyperTransport I/O Hub.
Signed-off-by: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce AMD8111 EDAC driver header file, which adds register and bits
definitions for the LPC Bridge Controller and PCI Bridge Controller on the
AMD8111 HyperTransport I/O Hub.
Signed-off-by: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds support for an EDAC memory controller adaptation driver for the
"ibm,sdram-4xx-ddr2" ECC controller realized in the AMCC PowerPC 405EX[r].
At present, this driver has been developed and tested against the
controller realization in the AMCC PPC405EX[r] on the AMCC Kilauea and
Haleakala boards (256 MiB w/o ECC memory soldered onto the board) and a
proprietary board based on those designs (128 MiB ECC memory, also
soldered onto the board).
In the future, dynamic feature detection and handling needs to be added
for the other realizations of this controller found in the 440SP, 440SPe,
460EX, 460GT and 460SX.
Eventually, this driver will likely be evolved and adapted to the above
variant realizations of this controller as well as broken apart to handle
the other known ECC-capable controllers prevalent in other PPC4xx
processors:
- IBM SDRAM (405GP, 405CR and 405EP) "ibm,sdram-4xx"
- IBM DDR1 (440GP, 440GX, 440EP and 440GR) "ibm,sdram-4xx-ddr"
- Denali DDR1/DDR2 (440EPX and 440GRX) "denali,sdram-4xx-ddr2"
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Grant Erickson <gerickson@nuovations.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After 3 years, this is a patch to remove the EXPERIMENTAL tag on EDAC. We
now have many module drivers submitters in EDAC and believe EDAC is no
longer EXPERIMENTAL
Signed-off-by: Doug Thompson <dougthompson@xmission.com
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A patch for making a debugging information more verbose for use in
development debugging.
By enabling the new option "More verbose debugging", information about
source file and line number will be added to debugging message.
This is sample output,
EDAC MC0: Giving out device to 'e7xxx_edac' 'E7205': DEV 0000:00:00.0
EDAC DEBUG: in drivers/edac/edac_pci.c, line at 48: edac_pci_alloc_ctl_info()
EDAC DEBUG: in drivers/edac/edac_pci.c, line at 334: edac_pci_add_device()
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Signed-off-by: Hitoshi Mitake <h.mitake@gmail.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These are all powerpc specific drivers.
res.start in fsl_elbc_nand.c needs to be cast since it may be either 32
or 64 bit. Thanks to Scott Wood for noticing.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Arnd Bergmann <arnd@arndb.de> call_edac bits in particular
Acked-by: Olof Johansson <olof@lixom.net> pasemi_nand peices
Acked-by: Scott Wood <scottwood@freescale.com> fsl_elbc fixes
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
All other compatibles that are uniquely identifying the processor use a
prefix of the form fsl,mpc85...'. We add support for it so we can
deprecate the older 'fsl,85...' that was improperly used here.
Additionally added mpc8536 & mpc8560 to the compatible lists.
This patch is based on Nate's 8572 patch.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Acked-by: Dave Jiang <djiang@mvista.com>
Cc: Nate Case <ncase@xes-inc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
