Use resource_size() instead of arithmetic.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Acked-by: Dave Jiang <djiang@mvista.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the ability to detect the specific data line or ECC line which failed
when printing out SDRAM single-bit errors. An example of a single-bit
SDRAM ECC error is below:
EDAC MPC85xx MC1: Err Detect Register: 0x80000004
EDAC MPC85xx MC1: Faulty data bit: 59
EDAC MPC85xx MC1: Expected Data / ECC: 0x7f80d000_409effa0 / 0x6d
EDAC MPC85xx MC1: Captured Data / ECC: 0x7780d000_409effa0 / 0x6d
EDAC MPC85xx MC1: Err addr: 0x00031ca0
EDAC MPC85xx MC1: PFN: 0x00000031
Knowning which specific data or ECC line caused an error can be useful in
tracking down hardware issues such as improperly terminated signals, loose
pins, etc.
Note that this feature is only currently enabled for 64-bit wide data
buses, 32-bit wide bus support should be added.
I don't have any 32-bit wide systems to test on. If someone has one and
is willing to give this patch a shot with the check for a 64-bit data bus
removed it would be much appreciated and I can re-submit with both 32 and
64 bit buses supported.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Dave Jiang <djiang@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With a 64-bit wide data bus only the lowest 8-bits of the ECC syndrome are
relevant. With a 32-bit wide data bus only the lowest 16-bits are
relevant on most architectures.
Without this change, the ECC syndrome displayed can be mildly confusing,
eg:
EDAC MPC85xx MC1: syndrome: 0x25252525
When in reality the ECC syndrome is 0x25.
A variety of Freescale manuals say a variety of different things about how
to decode the CAPTURE_ECC (syndrome) register. I don't have a system with
a 32-bit bus to test on, but I believe the change is correct. It'd be
good to get an ACK from someone at Freescale about this change though.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Dave Jiang <djiang@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some unused, unsupported debug code existed in the mpc85xx EDAC driver
that resulted in a build failure when CONFIG_EDAC_DEBUG was defined:
drivers/edac/mpc85xx_edac.c: In function 'mpc85xx_mc_err_probe':
drivers/edac/mpc85xx_edac.c:1031: error: implicit declaration of function 'edac_mc_register_mcidev_debug'
drivers/edac/mpc85xx_edac.c:1031: error: 'debug_attr' undeclared (first use in this function)
drivers/edac/mpc85xx_edac.c:1031: error: (Each undeclared identifier is reported only once
drivers/edac/mpc85xx_edac.c:1031: error: for each function it appears in.)
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit b484625172 ("edac: mpc85xx add
mpc83xx support") accidentally broke how a chip select's first and last
page addresses are calculated. The page addresses are being shifted too
far right by PAGE_SHIFT. This results in errors such as:
EDAC MPC85xx MC1: Err addr: 0x003075c0
EDAC MPC85xx MC1: PFN: 0x00000307
EDAC MPC85xx MC1: PFN out of range!
EDAC MC1: INTERNAL ERROR: row out of range (4 >= 4)
EDAC MC1: CE - no information available: INTERNAL ERROR
The vaule of PAGE_SHIFT is already being taken into consideration during
the calculation of the 'start' and 'end' variables, thus it is not
necessary to account for it again when setting a chip select's first and
last page address.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When building without CONFIG_PCI the edac_pci_idx variable is unused,
causing a build-time warning. Wrap the variable in #ifdef CONFIG_PCI,
just like the rest of the PCI support.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the Freescale MPC83xx memory controller to the existing
driver for the Freescale MPC85xx memory controller. The only difference
between the two processors are in the CS_BNDS register parsing code, which
has been changed so it will work on both processors.
The L2 cache controller does not exist on the MPC83xx, but the OF
subsystem will not use the driver if the device is not present in the OF
device tree.
I had to change the nr_pages calculation to make the math work out. I
checked it on my board and did the math by hand for a 64GB 85xx using 64K
pages. In both cases, nr_pages * PAGE_SIZE comes out to the correct
value.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Based on Kumar's new compatible types patch, add P2020 into MPC85xx EDAC
compatible lists so that EDAC can recognize P2020 meomry controller and L2
cache controller and export the relevant fields to sysfs.
EDAC MPC85xx DDR3 support is needed if DDR3 memory stick is installed on a
P2020DS board so that EDAC core can recognize DDR3 memory type.
Signed-off-by: Yang Shi <yang.shi@windriver.com>
Acked-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since some new MPC85xx SOCs support DDR3 memory now, so add DDR3 memory
type for MPC85xx EDAC.
Signed-off-by: Yang Shi <yang.shi@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Error found by Jeff Haran.
The error detect register is 0s when no errors are detected. The check
code is incorrect, so reverse check sense.
Reported-by: Jeff Haran <jharan@Brocade.COM>
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All other compatibles that are uniquely identifying the processor use a
prefix of the form fsl,mpc85...'. We add support for it so we can
deprecate the older 'fsl,85...' that was improperly used here.
Additionally added mpc8536 & mpc8560 to the compatible lists.
This patch is based on Nate's 8572 patch.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Acked-by: Dave Jiang <djiang@mvista.com>
Cc: Nate Case <ncase@xes-inc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds support for the dual-core MPC8572 processor. We have
to support making SPR changes on each core. Also, since we can
have multiple memory controllers sharing an interrupt, flag the
interrupts with IRQF_SHARED.
Signed-off-by: Andrew Kilkenny <akilkenny@xes-inc.com>
Signed-off-by: Nate Case <ncase@xes-inc.com>
Acked-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert PCI err device from platform to open firmware of_dev to comply
with powerpc schemes.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
including of <asm/mpc85xx.h> causes build problems since it doesn't exist.
Also removed warning:
drivers/edac/mpc85xx_edac.c:45: warning: 'mpc85xx_ctl_name' defined but not used
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Doug Thompson <dougthompson@xmission.com>
Acked-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Made a previous global variable, static in scope
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
