In fs/Makefile, ext3 was placed before ext2 so that a root filesystem
that possessed a journal, it would be mounted as ext3 instead of ext2.
This was necessary because a cleanly unmounted ext3 filesystem was
fully backwards compatible with ext2, and could be mounted by ext2 ---
but it was desirable that it be mounted with ext3 so that the
journaling would be enabled.
The ext4 filesystem supports new incompatible features, so there is no
danger of an ext4 filesystem being mistaken for an ext2 filesystem.
At that point, the relative ordering of ext4 with respect to ext2
didn't matter until ext4 gained the ability to mount filesystems
without a journal starting in 2.6.29-rc1. Now that this is the case,
given that ext4 is before ext2, it means that root filesystems that
were using the plain-jane ext2 format are getting mounted using the
ext4 filesystem driver, which is a change in behavior which could be
surprising to users.
It's doubtful that there are that many ext2-only root filesystem users
that would also have ext4 compiled into the kernel, but to adhere to
the principle of least surprise, the correct ordering in fs/Makefile
is ext3, followed by ext2, and finally ext4.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable: (864 commits)
Btrfs: explicitly mark the tree log root for writeback
Btrfs: Drop the hardware crc32c asm code
Btrfs: Add Documentation/filesystem/btrfs.txt, remove old COPYING
Btrfs: kmap_atomic(KM_USER0) is safe for btrfs_readpage_end_io_hook
Btrfs: Don't use kmap_atomic(..., KM_IRQ0) during checksum verifies
Btrfs: tree logging checksum fixes
Btrfs: don't change file extent's ram_bytes in btrfs_drop_extents
Btrfs: Use btrfs_join_transaction to avoid deadlocks during snapshot creation
Btrfs: drop remaining LINUX_KERNEL_VERSION checks and compat code
Btrfs: drop EXPORT symbols from extent_io.c
Btrfs: Fix checkpatch.pl warnings
Btrfs: Fix free block discard calls down to the block layer
Btrfs: avoid orphan inode caused by log replay
Btrfs: avoid potential super block corruption
Btrfs: do not call kfree if kmalloc failed in btrfs_sysfs_add_super
Btrfs: fix a memory leak in btrfs_get_sb
Btrfs: Fix typo in clear_state_cb
Btrfs: Fix memset length in btrfs_file_write
Btrfs: update directory's size when creating subvol/snapshot
Btrfs: add permission checks to the ioctls
...
There is going to be a new version of quota format having 64-bit
quota limits and a new quota format for OCFS2. They are both
going to use the same tree structure as VFSv0 quota format. So
split out tree handling into a separate file and make size of
leaf blocks, amount of space usable in each block (needed for
checksumming) and structures contained in them configurable
so that the code can be shared.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Creating a generic filesystem notification interface, fsnotify, which will be
used by inotify, dnotify, and eventually fanotify is really starting to
clutter the fs directory. This patch simply moves inotify and dnotify into
fs/notify/inotify and fs/notify/dnotify respectively to make both current fs/
and future notification tidier.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This just moves those files, but change link order from MSDOS, VFAT to
VFAT, MSDOS.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patchs adds the CONFIG_AIO option which allows to remove support
for asynchronous I/O operations, that are not necessarly used by
applications, particularly on embedded devices. As this is a
size-reduction option, it depends on CONFIG_EMBEDDED. It allows to
save ~7 kilobytes of kernel code/data:
text data bss dec hex filename
1115067 119180 217088 1451335 162547 vmlinux
1108025 119048 217088 1444161 160941 vmlinux.new
-7042 -132 0 -7174 -1C06 +/-
This patch has been originally written by Matt Mackall
<mpm@selenic.com>, and is part of the Linux Tiny project.
[randy.dunlap@oracle.com: build fix]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Cc: Zach Brown <zach.brown@oracle.com>
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-2.6.28' of git://linux-nfs.org/~bfields/linux: (59 commits)
svcrdma: Fix IRD/ORD polarity
svcrdma: Update svc_rdma_send_error to use DMA LKEY
svcrdma: Modify the RPC reply path to use FRMR when available
svcrdma: Modify the RPC recv path to use FRMR when available
svcrdma: Add support to svc_rdma_send to handle chained WR
svcrdma: Modify post recv path to use local dma key
svcrdma: Add a service to register a Fast Reg MR with the device
svcrdma: Query device for Fast Reg support during connection setup
svcrdma: Add FRMR get/put services
NLM: Remove unused argument from svc_addsock() function
NLM: Remove "proto" argument from lockd_up()
NLM: Always start both UDP and TCP listeners
lockd: Remove unused fields in the nlm_reboot structure
lockd: Add helper to sanity check incoming NOTIFY requests
lockd: change nlmclnt_grant() to take a "struct sockaddr *"
lockd: Adjust nlmsvc_lookup_host() to accomodate AF_INET6 addresses
lockd: Adjust nlmclnt_lookup_host() signature to accomodate non-AF_INET
lockd: Support non-AF_INET addresses in nlm_lookup_host()
NLM: Convert nlm_lookup_host() to use a single argument
svcrdma: Add Fast Reg MR Data Types
...
The ext4 filesystem is getting stable enough that it's time to drop
the "dev" prefix. Also remove the requirement for the TEST_FILESYS
flag.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This patch adds the CONFIG_FILE_LOCKING option which allows to remove
support for advisory locks. With this patch enabled, the flock()
system call, the F_GETLK, F_SETLK and F_SETLKW operations of fcntl()
and NFS support are disabled. These features are not necessarly needed
on embedded systems. It allows to save ~11 Kb of kernel code and data:
text data bss dec hex filename
1125436 118764 212992 1457192 163c28 vmlinux.old
1114299 118564 212992 1445855 160fdf vmlinux
-11137 -200 0 -11337 -2C49 +/-
This patch has originally been written by Matt Mackall
<mpm@selenic.com>, and is part of the Linux Tiny project.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Matt Mackall <mpm@selenic.com>
Cc: matthew@wil.cx
Cc: linux-fsdevel@vger.kernel.org
Cc: mpm@selenic.com
Cc: akpm@linux-foundation.org
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Adds OMFS to the fs Kconfig and Makefile
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for_linus' of git://git.infradead.org/~dedekind/ubifs-2.6:
UBIFS: include to compilation
UBIFS: add new flash file system
UBIFS: add brief documentation
MAINTAINERS: add UBIFS section
do_mounts: allow UBI root device name
VFS: export sync_sb_inodes
VFS: move inode_lock into sync_sb_inodes
Add UBIFS to Makefile and Kbuild.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Some block devices support verifying the integrity of requests by way
of checksums or other protection information that is submitted along
with the I/O.
This patch implements support for generating and verifying integrity
metadata, as well as correctly merging, splitting and cloning bios and
requests that have this extra information attached.
See Documentation/block/data-integrity.txt for more information.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This adds Kconfig and Makefile bits to build fs/compat_binfmt_elf.c,
just added. Each arch that wants to use this file needs to add a
"select COMPAT_BINFMT_ELF" line in its Kconfig bits that enable COMPAT.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since CONFIG_RAMFS is currently hard-selected to "y", and since
Documentation/filesystems/ramfs-rootfs-initramfs.txt reads as follows:
"The amount of code required to implement ramfs is tiny, because all the
work is done by the existing Linux caching infrastructure. Basically,
you're mounting the disk cache as a filesystem. Because of this, ramfs is
not an optional component removable via menuconfig, since there would be
negligible space savings."
It seems pointless to leave this as a Kconfig entry.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a very simple and light file descriptor, that can be used as event
wait/dispatch by userspace (both wait and dispatch) and by the kernel
(dispatch only). It can be used instead of pipe(2) in all cases where those
would simply be used to signal events. Their kernel overhead is much lower
than pipes, and they do not consume two fds. When used in the kernel, it can
offer an fd-bridge to enable, for example, functionalities like KAIO or
syslets/threadlets to signal to an fd the completion of certain operations.
But more in general, an eventfd can be used by the kernel to signal readiness,
in a POSIX poll/select way, of interfaces that would otherwise be incompatible
with it. The API is:
int eventfd(unsigned int count);
The eventfd API accepts an initial "count" parameter, and returns an eventfd
fd. It supports poll(2) (POLLIN, POLLOUT, POLLERR), read(2) and write(2).
The POLLIN flag is raised when the internal counter is greater than zero.
The POLLOUT flag is raised when at least a value of "1" can be written to the
internal counter.
The POLLERR flag is raised when an overflow in the counter value is detected.
The write(2) operation can never overflow the counter, since it blocks (unless
O_NONBLOCK is set, in which case -EAGAIN is returned).
But the eventfd_signal() function can do it, since it's supposed to not sleep
during its operation.
The read(2) function reads the __u64 counter value, and reset the internal
value to zero. If the value read is equal to (__u64) -1, an overflow happened
on the internal counter (due to 2^64 eventfd_signal() posts that has never
been retired - unlickely, but possible).
The write(2) call writes an __u64 count value, and adds it to the current
counter. The eventfd fd supports O_NONBLOCK also.
On the kernel side, we have:
struct file *eventfd_fget(int fd);
int eventfd_signal(struct file *file, unsigned int n);
The eventfd_fget() should be called to get a struct file* from an eventfd fd
(this is an fget() + check of f_op being an eventfd fops pointer).
The kernel can then call eventfd_signal() every time it wants to post an event
to userspace. The eventfd_signal() function can be called from any context.
An eventfd() simple test and bench is available here:
http://www.xmailserver.org/eventfd-bench.c
This is the eventfd-based version of pipetest-4 (pipe(2) based):
http://www.xmailserver.org/pipetest-4.c
Not that performance matters much in the eventfd case, but eventfd-bench
shows almost as double as performance than pipetest-4.
[akpm@linux-foundation.org: fix i386 build]
[akpm@linux-foundation.org: add sys_eventfd to sys_ni.c]
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch introduces a new system call for timers events delivered though
file descriptors. This allows timer event to be used with standard POSIX
poll(2), select(2) and read(2). As a consequence of supporting the Linux
f_op->poll subsystem, they can be used with epoll(2) too.
The system call is defined as:
int timerfd(int ufd, int clockid, int flags, const struct itimerspec *utmr);
The "ufd" parameter allows for re-use (re-programming) of an existing timerfd
w/out going through the close/open cycle (same as signalfd). If "ufd" is -1,
s new file descriptor will be created, otherwise the existing "ufd" will be
re-programmed.
The "clockid" parameter is either CLOCK_MONOTONIC or CLOCK_REALTIME. The time
specified in the "utmr->it_value" parameter is the expiry time for the timer.
If the TFD_TIMER_ABSTIME flag is set in "flags", this is an absolute time,
otherwise it's a relative time.
If the time specified in the "utmr->it_interval" is not zero (.tv_sec == 0,
tv_nsec == 0), this is the period at which the following ticks should be
generated.
The "utmr->it_interval" should be set to zero if only one tick is requested.
Setting the "utmr->it_value" to zero will disable the timer, or will create a
timerfd without the timer enabled.
The function returns the new (or same, in case "ufd" is a valid timerfd
descriptor) file, or -1 in case of error.
As stated before, the timerfd file descriptor supports poll(2), select(2) and
epoll(2). When a timer event happened on the timerfd, a POLLIN mask will be
returned.
The read(2) call can be used, and it will return a u32 variable holding the
number of "ticks" that happened on the interface since the last call to
read(2). The read(2) call supportes the O_NONBLOCK flag too, and EAGAIN will
be returned if no ticks happened.
A quick test program, shows timerfd working correctly on my amd64 box:
http://www.xmailserver.org/timerfd-test.c
[akpm@linux-foundation.org: add sys_timerfd to sys_ni.c]
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch series implements the new signalfd() system call.
I took part of the original Linus code (and you know how badly it can be
broken :), and I added even more breakage ;) Signals are fetched from the same
signal queue used by the process, so signalfd will compete with standard
kernel delivery in dequeue_signal(). If you want to reliably fetch signals on
the signalfd file, you need to block them with sigprocmask(SIG_BLOCK). This
seems to be working fine on my Dual Opteron machine. I made a quick test
program for it:
http://www.xmailserver.org/signafd-test.c
The signalfd() system call implements signal delivery into a file descriptor
receiver. The signalfd file descriptor if created with the following API:
int signalfd(int ufd, const sigset_t *mask, size_t masksize);
The "ufd" parameter allows to change an existing signalfd sigmask, w/out going
to close/create cycle (Linus idea). Use "ufd" == -1 if you want a brand new
signalfd file.
The "mask" allows to specify the signal mask of signals that we are interested
in. The "masksize" parameter is the size of "mask".
The signalfd fd supports the poll(2) and read(2) system calls. The poll(2)
will return POLLIN when signals are available to be dequeued. As a direct
consequence of supporting the Linux poll subsystem, the signalfd fd can use
used together with epoll(2) too.
The read(2) system call will return a "struct signalfd_siginfo" structure in
the userspace supplied buffer. The return value is the number of bytes copied
in the supplied buffer, or -1 in case of error. The read(2) call can also
return 0, in case the sighand structure to which the signalfd was attached,
has been orphaned. The O_NONBLOCK flag is also supported, and read(2) will
return -EAGAIN in case no signal is available.
If the size of the buffer passed to read(2) is lower than sizeof(struct
signalfd_siginfo), -EINVAL is returned. A read from the signalfd can also
return -ERESTARTSYS in case a signal hits the process. The format of the
struct signalfd_siginfo is, and the valid fields depends of the (->code &
__SI_MASK) value, in the same way a struct siginfo would:
struct signalfd_siginfo {
__u32 signo; /* si_signo */
__s32 err; /* si_errno */
__s32 code; /* si_code */
__u32 pid; /* si_pid */
__u32 uid; /* si_uid */
__s32 fd; /* si_fd */
__u32 tid; /* si_fd */
__u32 band; /* si_band */
__u32 overrun; /* si_overrun */
__u32 trapno; /* si_trapno */
__s32 status; /* si_status */
__s32 svint; /* si_int */
__u64 svptr; /* si_ptr */
__u64 utime; /* si_utime */
__u64 stime; /* si_stime */
__u64 addr; /* si_addr */
};
[akpm@linux-foundation.org: fix signalfd_copyinfo() on i386]
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch add an anonymous inode source, to be used for files that need
and inode only in order to create a file*. We do not care of having an
inode for each file, and we do not even care of having different names in
the associated dentries (dentry names will be same for classes of file*).
This allow code reuse, and will be used by epoll, signalfd and timerfd
(and whatever else there'll be).
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce several fsstack_copy_* functions which allow stackable filesystems
(such as eCryptfs and Unionfs) to easily copy over (currently only) inode
attributes. This prevents code duplication and allows for code reuse.
[akpm@osdl.org: Remove unneeded wrapper]
[bunk@stusta.de: fs/stack.c should #include <linux/fs_stack.h>]
Signed-off-by: Josef "Jeff" Sipek <jsipek@cs.sunysb.edu>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reworked from a patch by Mingming Cao and Randy Dunlap
Signed-off-By: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Dave Kleikamp <shaggy@austin.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Originally part of a patch from Mingming Cao and Randy Dunlap. Reorganized
by Shaggy.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Mingming Cao<cmm@us.ibm.com>
Signed-off-by: Dave Kleikamp <shaggy@austin.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
eCryptfs is a stacked cryptographic filesystem for Linux. It is derived from
Erez Zadok's Cryptfs, implemented through the FiST framework for generating
stacked filesystems. eCryptfs extends Cryptfs to provide advanced key
management and policy features. eCryptfs stores cryptographic metadata in the
header of each file written, so that encrypted files can be copied between
hosts; the file will be decryptable with the proper key, and there is no need
to keep track of any additional information aside from what is already in the
encrypted file itself.
[akpm@osdl.org: updates for ongoing API changes]
[bunk@stusta.de: cleanups]
[akpm@osdl.org: alpha build fix]
[akpm@osdl.org: cleanups]
[tytso@mit.edu: inode-diet updates]
[pbadari@us.ibm.com: generic_file_*_read/write() interface updates]
[rdunlap@xenotime.net: printk format fixes]
[akpm@osdl.org: make slab creation and teardown table-driven]
Signed-off-by: Phillip Hellewell <phillip@hellewell.homeip.net>
Signed-off-by: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Erez Zadok <ezk@cs.sunysb.edu>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make it possible to disable the block layer. Not all embedded devices require
it, some can make do with just JFFS2, NFS, ramfs, etc - none of which require
the block layer to be present.
This patch does the following:
(*) Introduces CONFIG_BLOCK to disable the block layer, buffering and blockdev
support.
(*) Adds dependencies on CONFIG_BLOCK to any configuration item that controls
an item that uses the block layer. This includes:
(*) Block I/O tracing.
(*) Disk partition code.
(*) All filesystems that are block based, eg: Ext3, ReiserFS, ISOFS.
(*) The SCSI layer. As far as I can tell, even SCSI chardevs use the
block layer to do scheduling. Some drivers that use SCSI facilities -
such as USB storage - end up disabled indirectly from this.
(*) Various block-based device drivers, such as IDE and the old CDROM
drivers.
(*) MTD blockdev handling and FTL.
(*) JFFS - which uses set_bdev_super(), something it could avoid doing by
taking a leaf out of JFFS2's book.
(*) Makes most of the contents of linux/blkdev.h, linux/buffer_head.h and
linux/elevator.h contingent on CONFIG_BLOCK being set. sector_div() is,
however, still used in places, and so is still available.
(*) Also made contingent are the contents of linux/mpage.h, linux/genhd.h and
parts of linux/fs.h.
(*) Makes a number of files in fs/ contingent on CONFIG_BLOCK.
(*) Makes mm/bounce.c (bounce buffering) contingent on CONFIG_BLOCK.
(*) set_page_dirty() doesn't call __set_page_dirty_buffers() if CONFIG_BLOCK
is not enabled.
(*) fs/no-block.c is created to hold out-of-line stubs and things that are
required when CONFIG_BLOCK is not set:
(*) Default blockdev file operations (to give error ENODEV on opening).
(*) Makes some /proc changes:
(*) /proc/devices does not list any blockdevs.
(*) /proc/diskstats and /proc/partitions are contingent on CONFIG_BLOCK.
(*) Makes some compat ioctl handling contingent on CONFIG_BLOCK.
(*) If CONFIG_BLOCK is not defined, makes sys_quotactl() return -ENODEV if
given command other than Q_SYNC or if a special device is specified.
(*) In init/do_mounts.c, no reference is made to the blockdev routines if
CONFIG_BLOCK is not defined. This does not prohibit NFS roots or JFFS2.
(*) The bdflush, ioprio_set and ioprio_get syscalls can now be absent (return
error ENOSYS by way of cond_syscall if so).
(*) The seclvl_bd_claim() and seclvl_bd_release() security calls do nothing if
CONFIG_BLOCK is not set, since they can't then happen.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The patches solve the following problem: We want to grant access to devices
based on who is logged in from where, etc. This includes switching back and
forth between multiple user sessions, etc.
Using ACLs to define device access for logged-in users gives us all the
flexibility we need in order to fully solve the problem.
Device special files nowadays usually live on tmpfs, hence tmpfs ACLs.
Different distros have come up with solutions that solve the problem to
different degrees: SUSE uses a resource manager which tracks login sessions
and sets ACLs on device inodes as appropriate. RedHat uses pam_console, which
changes the primary file ownership to the logged-in user. Others use a set of
groups that users must be in in order to be granted the appropriate accesses.
The freedesktop.org project plans to implement a combination of a
console-tracker and a HAL-device-list based solution to grant access to
devices to users, and more distros will likely follow this approach.
These patches have first been posted here on 2 February 2005, and again
on 8 January 2006. We have been shipping them in SLES9 and SLES10 with
no problems reported. The previous submission is archived here:
http://lkml.org/lkml/2006/1/8/229http://lkml.org/lkml/2006/1/8/230http://lkml.org/lkml/2006/1/8/231
This patch:
Add some infrastructure for access control lists on in-memory
filesystems such as tmpfs.
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the first patch in a series of patches that removes devfs
support from the kernel. This patch removes the core devfs code, and
its private header file.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following series of patches introduces a kernel API for inotify,
making it possible for kernel modules to benefit from inotify's
mechanism for watching inodes. With these patches, inotify will
maintain for each caller a list of watches (via an embedded struct
inotify_watch), where each inotify_watch is associated with a
corresponding struct inode. The caller registers an event handler and
specifies for which filesystem events their event handler should be
called per inotify_watch.
Signed-off-by: Amy Griffis <amy.griffis@hp.com>
Acked-by: Robert Love <rml@novell.com>
Acked-by: John McCutchan <john@johnmccutchan.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
configfs_init() needs to be called first to register configfs before anyconsumers try to access it. Move up configfs in fs/Makefile to make
sure it is initialized early.
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Remove the recently-added LINUX_FADV_ASYNC_WRITE and LINUX_FADV_WRITE_WAIT
fadvise() additions, do it in a new sys_sync_file_range() syscall instead.
Reasons:
- It's more flexible. Things which would require two or three syscalls with
fadvise() can be done in a single syscall.
- Using fadvise() in this manner is something not covered by POSIX.
The patch wires up the syscall for x86.
The sycall is implemented in the new fs/sync.c. The intention is that we can
move sys_fsync(), sys_fdatasync() and perhaps sys_sync() into there later.
Documentation for the syscall is in fs/sync.c.
A test app (sync_file_range.c) is in
http://www.zip.com.au/~akpm/linux/patches/stuff/ext3-tools.tar.gz.
The available-to-GPL-modules do_sync_file_range() is for knfsd: "A COMMIT can
say NFS_DATA_SYNC or NFS_FILE_SYNC. I can skip the ->fsync call for
NFS_DATA_SYNC which is hopefully the more common."
Note: the `async' writeout mode SYNC_FILE_RANGE_WRITE will turn synchronous if
the queue is congested. This is trivial to fix: add a new flag bit, set
wbc->nonblocking. But I'm not sure that we want to expose implementation
details down to that level.
Note: it's notable that we can sync an fd which wasn't opened for writing.
Same with fsync() and fdatasync()).
Note: the code takes some care to handle attempts to sync file contents
outside the 16TB offset on 32-bit machines. It makes such attempts appear to
succeed, for best 32-bit/64-bit compatibility. Perhaps it should make such
requests fail...
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds support for the sys_splice system call. Using a pipe as a
transport, it can connect to files or sockets (latter as output only).
From the splice.c comments:
"splice": joining two ropes together by interweaving their strands.
This is the "extended pipe" functionality, where a pipe is used as
an arbitrary in-memory buffer. Think of a pipe as a small kernel
buffer that you can use to transfer data from one end to the other.
The traditional unix read/write is extended with a "splice()" operation
that transfers data buffers to or from a pipe buffer.
Named by Larry McVoy, original implementation from Linus, extended by
Jens to support splicing to files and fixing the initial implementation
bugs.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the core of the distributed lock manager which is required
to use GFS2 as a cluster filesystem. It is also used by CLVM and
can be used as a standalone lock manager independantly of either
of these two projects.
It implements VAX-style locking modes.
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Steve Whitehouse <swhiteho@redhat.com>
Adds GFS2 into fs/Kconfig and adds a Makefile entry
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Now that all these entries in the arch ioctl32.c files are gone [1], we can
build fs/compat_ioctl.c as a normal object and kill tons of cruft. We need a
special do_ioctl32_pointer handler for s390 so the compat_ptr call is done.
This is not needed but harmless on all other architectures. Also remove some
superflous includes in fs/compat_ioctl.c
Tested on ppc64.
[1] parisc still had it's PPP handler left, which is not fully correct
for ppp and besides that ppp uses the generic SIOCPRIV ioctl so it'd
kick in for all netdevice users. We can introduce a proper handler
in one of the next patch series by adding a compat_ioctl method to
struct net_device but for now let's just kill it - parisc doesn't
compile in mainline anyway and I don't want this to block this
patchset.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Matthew Wilcox <willy@debian.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add /proc/sys/vm/drop_caches. When written to, this will cause the kernel to
discard as much pagecache and/or reclaimable slab objects as it can. THis
operation requires root permissions.
It won't drop dirty data, so the user should run `sync' first.
Caveats:
a) Holds inode_lock for exorbitant amounts of time.
b) Needs to be taught about NUMA nodes: propagate these all the way through
so the discarding can be controlled on a per-node basis.
This is a debugging feature: useful for getting consistent results between
filesystem benchmarks. We could possibly put it under a config option, but
it's less than 300 bytes.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Link the code into the kernel build system. OCFS2 is marked as
experimental.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Signed-off-by: Kurt Hackel <kurt.hackel@oracle.com>
Configfs, a file system for userspace-driven kernel object configuration.
The OCFS2 stack makes extensive use of this for propagation of cluster
configuration information into kernel.
Signed-off-by: Joel Becker <joel.becker@oracle.com>
