I forgot to remove the ide_etrax100 chipset type when removing the
ETRAX_IDE driver.
Reported-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Disable Virtual DMA support for now (it causes system hangs).
Thanks to TAKADA Yoshihito for the help with debugging the problem.
Reported-by: TAKADA Yoshihito <takada@mbf.nifty.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
SELECT_MASK() can now become static.
[bart: remove space between function name and open parenthesis]
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use 'hwif->dma_base + {4,8}' instead of hwif->dma_prdtable in
{ide,scc}_dma_setup().
* Remove no longer needed ->dma_prdtable field from ide_hwif_t.
While at it:
* Use ATA_DMA_TABLE_OFS define.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use 'hwif->dma_base + {1,3}' instead of hwif->dma_vendor{1,3} in
pdc202xx_new host driver.
* Remove no longer needed ->dma_vendor{1,3} fields from ide_hwif_t.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_pad_transfer() helper (which uses ->{in,out}put_data methods
internally so the transfer is also padded to drive+host requirements)
and use it instead of ide_atapi_{write_zeros,discard_data}().
* Remove no longer needed ide_atapi_{write_zeros,discard_data}().
Cc: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove no longer used ->INW and ->OUTW methods.
While at it:
* scc_pata.c: scc_ide_{out,in}w() is called only in scc_tf_{load,read}()
so inline it there.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->tf_load and ->tf_read methods to ide_hwif_t and set the default
methods in default_hwif_transport().
* Use ->tf_{load,read} instead o calling ide_tf_{load,read}() directly.
* Make ide_tf_{load,read}() static.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Factor out debugging code from ide_tf_load() to ide_tf_dump() helper
and update ide_tf_load() users accordingly.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_execute_pkt_cmd() helper for executing PACKET command,
then convert ATAPI device drivers to use it.
As a nice side-effect this fixes ide-{floppy,tape,scsi} w.r.t.
ide_lock taking (ide-cd was OK).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use ins{w,l}()/outs{w,l}() and __ide_mm_ins{w,l}()/__ide_mm_outs{w,l}()
directly in ata_{in,out}put_data() (by using IDE_HFLAG_MMIO host flag to
decide which I/O ops are required).
* Remove no longer needed ->INS{W,L} and ->OUTS{W,L} methods (ide-h8300,
au1xxx-ide and scc_pata implement their own ->{in,out}put_data methods).
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_HFLAG_MMIO host flag and set it for hosts which use
default_hwif_mmiops().
v2:
* Fix kernel panic in pmac host driver (',' should be '|').
Thanks to Kamalesh for reporting it + testing the fix
and to Andrew for hinting me about the source of the issue.
Cc: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Merge ->atapi_{in,out}put_bytes and ->ata_{in,out}put_data methods
into new ->{in,out}put_data methods which take number of bytes to
transfer as an argument and always do padding.
While at it:
* Use 'hwif' or 'drive->hwif' instead of 'HWIF(drive)'.
There should be no functional changes caused by this patch (all users
of ->ata_{in,out}put_data methods were using multiply-of-4 word counts).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->atapi_{in,out}put_bytes and ->ata_{in,out}put_data methods to
falconide and q40ide host drivers (->ata_* methods are implemented on
top of ->atapi_* methods so they also do byte-swapping now).
* Cleanup atapi_{in,out}put_bytes().
v2:
* Add 'struct request *rq' argument to ->ata_{in,out}put_data methods
and don't byte-swap disk fs requests (we shouldn't un-swap fs requests
because fs itself is stored byte-swapped on the disk) - this is how
things were done before the patch (ideally device mapper should be
used instead but it would break existing setups and would have some
performance impact).
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michael Schmitz <schmitz@debian.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Richard Zidlicky <rz@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add struct ide_io_ports and use it instead of `unsigned long io_ports[]`
in ide_hwif_t.
* Rename io_ports[] in hw_regs_t to io_ports_array[].
* Use un-named union for 'unsigned long io_ports_array[]' and 'struct
ide_io_ports io_ports' in hw_regs_t.
* Remove IDE_*_OFFSET defines.
v2:
* scc_pata.c build fix from Stephen Rothwell.
v3:
* Fix ctl_adrr typo in Sparc-specific part of ns87415.c.
(Noticed by Andrew Morton)
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Make ide_unregister() take 'ide_hwif_t *hwif' instead of 'unsigned int
index' (hwif->index) as an argument and update all users accordingly.
While at it:
* Remove unnecessary checks for hwif != NULL from ide-pnp.c::idepnp_remove()
and delkin_cb.c::delkin_cb_remove().
* Remove needless hwif->chipset assignment from scc_pata.c::scc_remove().
v2:
* Fixup ide_unregister() documentation.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Don't set IDE_HFLAG_NO_AUTOTUNE host flag in sgiioc4 and icside
host drivers - there is no need for it as they don't implement
->set_pio_mode method.
* Remove no longer needed IDE_HFLAG_NO_AUTOTUNE host flag.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add "vlb_clock=" parameter for specifying VLB clock frequency (in MHz).
* Add "pci_clock=" parameter for specifying PCI bus clock frequency (in MHz).
While at it:
* qd65xx.c: rename {active,recovery}_cycle variables to {act,rec}_cyc.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove obsoleted "hdx=noautotune" kernel parameter
(it has been obsoleted since 1 Nov 2004).
Then make ide_hwif_t.autotune a single bit flag
and remove no longer needed IDE_TUNE_* defines.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove obsoleted "idex=reset" kernel parameter
(it has been obsoleted since 1 Nov 2004).
Then remove corresponding code from ide_probe_port()
and no longer used ->reset field from ide_hwif_t.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add "ignore_cable" parameter:
* "ide_core.ignore_cable=[interface_number]" boot option if IDE is built-in
(i.e. "ide_core.ignore_cable=1" to force ignoring cable for "ide1")
* "ignore_cable=[interface_number]" module parameter (for ide_core module)
if IDE is compiled as module
v2:
* Add ide_port_apply_params() helper
- use it in ide_device_add_all() and ide_scan_port().
* Make it possible to later disable ignoring cable detection by passing
"[interface_number]:0" to /sys/module/ide_core/parameters/ignore_cable
(however sysfs interface is not enabled yet since it needs some other
IDE changes to make it work reliable).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Export ide_dma_exec_cmd() and __ide_dma_test_irq().
* Constify struct ide_dma_ops.
* Always set hwif->dma_ops to &sff_dma_ops in ide_setup_dma()
(it is later overriden by ide_init_port() if needed) and drop
'const struct ide_port_info *d' argument.
While at it:
* Rename __ide_dma_test_irq() to ide_dma_test_irq().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add struct ide_dma_ops and convert core code + drivers to use it.
While at it:
* Drop "ide_" prefix from ->ide_dma_end and ->ide_dma_test_irq methods.
* Drop "ide_" "infixes" from DMA methods.
* au1xxx-ide.c:
- use auide_dma_{test_irq,end}() directly in auide_dma_timeout()
* pdc202xx_old.c:
- drop "old_" "infixes" from DMA methods
* siimage.c:
- add siimage_dma_test_irq() helper
- print SATA warning in siimage_init_one()
* Remove no longer needed ->init_hwif implementations.
v2:
* Changes based on review from Sergei:
- s/siimage_ide_dma_test_irq/siimage_dma_test_irq/
- s/drive->hwif/hwif/ in idefloppy_pc_intr().
- fix patch description w.r.t. au1xxx-ide changes
- fix au1xxx-ide build
- fix naming for cmd64*_dma_ops
- drop "ide_" and "old_" infixes
- s/hpt3xxx_dma_ops/hpt37x_dma_ops/
- s/hpt370x_dma_ops/hpt370_dma_ops/
- use correct DMA ops for HPT302/N, HPT371/N and HPT374
- s/it821x_smart_dma_ops/it821x_pass_through_dma_ops/
v3:
* Two bugs slipped in v2 (noticed by Sergei):
- use correct DMA ops for HPT374 (for real this time)
- handle HPT370/HPT370A properly
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_HFLAG_SERIALIZE_DMA host flag to serialize ports
if DMA is available and handle it in ide_init_port().
* Convert sl82c105 host driver to use this new flag.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Make ide_hwif_setup_dma() return an error value.
* Pass 'const struct ide_port_info *d' instead of 'unsigned long dmabase'
to ->init_dma method and make it return an error value.
* Rename ide_get_or_set_dma_base() to ide_pci_dma_base(),
change ordering of its arguments and then export it.
* Export ide_pci_set_master().
* Do complete DMA setup inside ->init_dma method and update ->init_dma
users accordingly.
* Sanitize code for DMA setup in ide_init_port().
v2:
* Fix for CONFIG_BLK_DEV_IDEDMA_PCI=n configs
(from Jiri Slaby <jirislaby@gmail.com>):
Fix following compiler warning by returning EINVAL:
In file included from ANYTHING-INCLUDING-IDE.H:45:
include/linux/ide.h: In function ‘ide_hwif_setup_dma’:
include/linux/ide.h:1022: warning: no return statement in function returning non-void
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Export ide_allocate_dma_engine() and use it in trm290 host driver.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use hwif->name instead of cds->name in ide_allocate_dma_engine().
* Use pci_name(dev) instead of cds->name in init_dma_pdc202xx().
* Remove no longer needed ->cds field from ide_hwif_t.
v2:
* scc_pata.c also needs to be updated now (noticed by Stephen Rothwell).
There should be no functional changes caused by this patch.
Cc: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Cc: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Always setup hwif->extra_base in ide_iomio_dma() and remove
no longer needed ->extra field from struct ide_port_info.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Reserve PCI BARs 0-3 (0-1 for single port controllers) in
ide_pci_enable() and remove ide_hwif_request_regions() call
from ide_device_add_all() (also cleanup resource management
in scc_pata host driver).
* Fix handling of PCI BAR 4 in ide_pci_enable(), then cleanup
ide_iomio_dma() (+ init_hwif_trm290() in trm290 host driver)
and remove ide_release[_iomio]_dma().
v2:
* Fixup trm290 host driver.
v3:
* Because of scc_pata host driver changes we need to call
pci_request_selected_regions() also in setup_mmio_scc().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
All host drivers using ide_unregister()/module_exit() have been fixed
to manage resources themselves so this function can be removed now.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add 'unsigned long config' argument to ide_legacy_device_add()
for setting hwif->config_data.
* Use ide_find_port_slot() instead of ide_find_port() in
ide_legacy_device_add().
* Handle IDE_HFLAG_QD_2ND_PORT and IDE_HFLAG_SINGLE host flags in
ide_legacy_device_add().
* Convert qd65xx host driver to use ide_legacy_device_add().
v2:
* Update ali14xx, dtc2278, ht6560b and umc8672 host drivers.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_legacy_device_add() helper for use by legacy VLB host drivers
(+ convert them to use it).
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Update IDE PMAC host driver to use drive->noprobe instead of hwif->noprobe
and remove hwif->noprobe completely (it is always set to zero now).
There should be no functional changes caused by this patch.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move hooks for port/host specific methods from ide_hwif_t to
'struct ide_port_ops'.
* Add 'const struct ide_port_ops *port_ops' to 'struct ide_port_info'
and ide_hwif_t.
* Update host drivers and core code accordingly.
While at it:
* Rename ata66_*() cable detect functions to *_cable_detect() to match
the standard naming. (Suggested by Sergei Shtylyov)
v2:
* Fix build for bast-ide. (Noticed by Andrew Morton)
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
All host drivers now either set hwif->mmio or reserve continuous
I/O resources so remove no longer needed hwif->straight8 flag
and never reached code for 'hwif->straight8 == 0' case.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei suggested that it shouldn't be necessary + it had no effect
anyway since ide_id_dma_bug() is called earlier in ide_tune_dma().
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_HFLAG_QD_2ND_PORT host flag to indicate the need of skipping
first ide_hwifs[] slot for the second port of QD65xx controller.
* Handle this new host flag in ide_find_port_slot().
* Convert legacy VLB host drivers to use ide_find_port().
While at it:
* Fix couple of printk()-s in qd65xx host driver to not use hwif->name.
v2:
* Fix qd65xx.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Change ide_match_hwif() argument from 'u8 bootable' to
'struct ide_port_info *d'.
* Move ide_match_hwif() to ide-probe.c from setup-pci.c and rename
it to ide_find_port_slot(). Update some comments while at it.
* ide_find_port() can be now just a wrapper for ide_find_port_slot().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
No need for it nowadays so remove quirk code from ide_get_best_pio_mode()
and IDE_HFLAG_PIO_DOWNGRADE host flag.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
"bootable" should be the default behavior so replace
IDE_HFLAG_BOOTABLE host flag with IDE_HFLAG_NON_BOOTABLE.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
None of these files use any of the functionality promised by
asm/semaphore.h. It's possible that they (or some user of them) rely
on it dragging in some unrelated header file, but I can't build all
these files, so we'll have to fix any build failures as they come up.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
* Add CONFIG_IDE_ARCH_OBSOLETE_DEFAULTS to drivers/ide/Kconfig and use
it instead of defining IDE_ARCH_OBSOLETE_DEFAULTS in <arch/ide.h>.
v2:
* Define ide_default_irq() in ide-probe.c/ns87415.c if not already defined
and drop defining ide_default_irq() for CONFIG_IDE_ARCH_OBSOLETE_DEFAULTS=n.
[ Thanks to Stephen Rothwell and David Miller for noticing the problem. ]
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This new struct unifies ide{-floppy,-tape,-scsi}'s view of a packet command. For now,
it represents the common denominator between the three drivers while adding driver-
specific members at the end of the struct which will be merged/simplified into the
generic ATAPI handling code in later steps, or removed completely.
Bart:
- move struct ide_atapi_pc outside of #ifdef/#endif CONFIG_IDE_PROC_FS
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_{ALTSTATUS,IREASON,BCOUNTL,BCOUNTH}_OFFSET defines.
* Remove IDE_*_REG macros - this results in more readable
and slightly smaller code.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_atapi_{discard_data,write_zeros} inline helpers to <linux/ide.h>
and use them instead of home-brewn helpers in ide-{floppy,tape,scsi}.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
hdparm explicitely marks HDIO_[UNREGISTER,SCAN]_HWIF ioctls as DANGEROUS
and given the number of bugs we can assume that there are no real users:
* DMA has no chance of working because DMA resources are released by
ide_unregister() and they are never allocated again.
* Since ide_init_hwif_ports() is used for ->io_ports[] setup the ioctls
don't work for almost all hosts with "non-standard" (== non ISA-like)
layout of IDE taskfile registers (there is a lot of such host drivers).
* ide_port_init_devices() is not called when probing IDE devices so:
- drive->autotune is never set and IDE host/devices are not programmed
for the correct PIO/DMA transfer modes (=> possible data corruption)
- host specific I/O 32-bit and IRQ unmasking settings are not applied
(=> possible data corruption)
- host specific ->port_init_devs method is not called (=> no luck with
ht6560b, qd65xx and opti621 host drivers)
* ->rw_disk method is not preserved (=> no HPT3xxN chipsets support).
* ->serialized flag is not preserved (=> possible data corruption when
using icside, aec62xx (ATP850UF chipset), cmd640, cs5530, hpt366
(HPT3xxN chipsets), rz1000, sc1200, dtc2278 and ht6560b host drivers).
* ->ack_intr method is not preserved (=> needed by ide-cris, buddha,
gayle and macide host drivers).
* ->sata_scr[] and sata_misc[] is cleared by ide_unregister() and it
isn't initialized again (SiI3112 support needs them).
* To issue an ioctl() there need to be at least one IDE device present
in the system.
* ->cable_detect method is not preserved + it is not called when probing
IDE devices so cable detection is broken (however since DMA support is
also broken it doesn't really matter ;-).
* Some objects which may have already been freed in ide_unregister()
are restored by ide_hwif_restore() (i.e. ->hwgroup).
* ide_register_hw() may unregister unrelated IDE ports if free ide_hwifs[]
slot cannot be found.
* When IDE host drivers are modular unregistered port may be re-used by
different host driver that owned it first causing subtle bugs.
Since we now have a proper warm-plug support remove these ioctls,
then remove no longer needed:
- ide_register_hw() and ide_hwif_restore() functions
- 'init_default' and 'restore' arguments of ide_unregister()
- zeroeing of hwif->{dma,extra}_* fields in ide_unregister()
As an added bonus IDE core code size shrinks by ~3kB (x86-32).
v2:
* fix ide_unregister() arguments in cleanup_module() (Andrew Morton).
v3:
* fix ide_unregister() arguments in palm_bk3710.c.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add 'struct class ide_port_class' ('ide_port' class) and a 'struct
device *portdev' ('ide_port' class device) in ide_hwif_t.
* Register 'ide_port' class in ide_init() and unregister it in
cleanup_module().
* Create ->portdev in ide_register_port () and unregister it in
ide_unregister().
* Add "delete_devices" class device attribute for unregistering IDE devices
on a port and "scan" one for probing+registering IDE devices on a port.
* Add ide_sysfs_register_port() helper for registering "delete_devices"
and "scan" attributes with ->portdev. Call it in ide_device_add_all().
* Document IDE warm-plug support in Documentation/ide/warm-plug-howto.txt.
v2:
* Convert patch from using 'struct class_device' to use 'struct device'.
(thanks to Kay Sievers for doing it)
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
->busproc method is used by HDIO_SET_BUSSTATE ioctl but it has no chance
of working as intended (in 2.4.x days) because to issue an ioctl there
is a device node needed and:
- for BUSSTATE_TRISTATE+OFF it is too late (devices are already gone)
- for BUSSTATE_TRISTATE+ON it is too early (devices are not registered yet)
Just remove ->busproc method for now (it was only implemented by hpt366,
siimage and tc86c001 host drivers).
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Rework PowerMac media-bay support in such way that instead of
un/registering the IDE interface we un/register IDE devices:
* Add ide_port_scan() helper for probing+registerering devices on a port.
* Rename ide_port_unregister_devices() to __ide_port_unregister_devices().
* Add ide_port_unregister_devices() helper for unregistering devices on a port.
* Add 'ide_hwif_t *cd_port' to 'struct media_bay_info', pass 'hwif' instead
of hwif->index to media_bay_set_ide_infos() and use it to setup 'cd_port'.
* Use ide_port_unregister_devices() instead of ide_unregister()
and ide_port_scan() instead of ide_register_hw() in media_bay_step().
* Unexport ide_register_hw() and make it static.
v2:
* Fix build by adding <linux/ide.h> include to <asm-powerpc/mediabay.h>.
(Reported by Michael/Kamalesh/Andrew).
Cc: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
IDE devices need to be removed from /proc/ide/ _before_ being unregistered:
* Drop 'ide_hwif_t *hwif' argument from destroy_proc_ide_device()
and use drive->hwif instead.
* Rename destroy_proc_ide_device() to ide_proc_unregister_device().
* Call ide_proc_unregister_device() in drive_release_dev().
* Remove no longer needed destroy_proc_ide_drives().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use ide_find_port() instead of ide_deprecated_find_port() in bast-ide/
palm_bk3710/ide-cs/delkin_cb host drivers and in ide_register_hw().
* Remove no longer needed ide_deprecated_find_port().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This option is obsolete and can be removed safely.
It allows us to remove the pci_get_device_reverse() function from the
PCI core.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Without this patch a Opteron test system here oopses at boot with
current git.
Calling to_pci_dev() on a NULL pointer gives a negative value so the
following NULL pointer check never triggers and then an illegal address
is referenced. Check the unadjusted original device pointer for NULL
instead.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit 813a0eb233
Author: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Date: Fri Jan 25 22:17:10 2008 +0100
ide: switch idedisk_prepare_flush() to use REQ_TYPE_ATA_TASKFILE requests
...
broke flush requests.
Allocating IDE command structure on the stack for flush requests is not
a very brilliant idea:
- idedisk_prepare_flush() only prepares the request and it doesn't wait
for it to be completed
- there are can be multiple flush requests queued in the queue
Fix the problem (per hints from James Bottomley) by:
- dynamically allocating ide_task_t instance using kmalloc(..., GFP_ATOMIC)
- adding new taskfile flag (IDE_TFLAG_DYN)
- calling kfree() in ide_end_drive_command() if IDE_TFLAG_DYN is set
(while at it rename 'args' to 'task' and fix whitespace damage)
[ This will be fixed properly before 2.6.25 but this bug is rather
critical and the proper solution requires some more work + testing. ]
Thanks to Sebastian Siewior and Christoph Hellwig for reporting the
problem and testing patches (extra thanks to Sebastian for bisecting
it to the guilty commmit).
Tested-by: Sebastian Siewior <ide-bug@ml.breakpoint.cc>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Introduce new option CONFIG_BLK_DEV_IDEDMA_SFF for non-PCI SFF-8038i compatible
bus mastering IDE controllers (which there are a few known), thus fixing a hack
made for Palmchip BK3710 controller...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Anton Salnikov <asalnikov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide-cris.c:
* Add cris_setup_ports() helper and use it instead of ide_setup_ports()
(fixes random value being set in ->io_ports[IDE_IRQ_OFFSET]).
buddha.c:
* Add buddha_setup_ports() helper and use it instead of ide_setup_ports().
falconide.c:
* Add falconide_setup_ports() helper and use it instead of ide_setup_ports(),
also fix return value of falconide_init() while at it.
gayle.c:
* Add gayle_setup_ports() helper and use it instead of ide_setup_ports().
macide.c:
* Add macide_setup_ports() helper and use it instead of ide_setup_ports()
(fixes incorrect value being set in ->io_ports[IDE_IRQ_OFFSET]).
q40ide.c:
* Fix q40_ide_setup_ports() comments.
ide.c:
* Remove no longer needed ide_setup_ports().
Cc: Mikael Starvik <starvik@axis.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This is Palmchip BK3710 IDE controller support.
The IDE controller logic supports PIO, MultiWord-DMA and Ultra-DMA modes.
Supports interface to Compact Flash (CF) configured in True-IDE mode.
Bart:
- remove dead code
- fix ide_hwif_setup_dma() build problem
Signed-off-by: Anton Salnikov <asalnikov@ru.mvista.com>
Reviewed-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move check_dma_crc() to ide-dma.c and add inline version for
CONFIG_BLK_DEV_IDEDMA=n case.
* Rename check_dma_crc() to ide_check_dma_crc().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* siimage.c: use hwif->sata_scr[SATA_{ERROR,STATUS}_OFFSET] instead of
SATA_{ERROR,STATUS}_REG macros.
* Remove no longer needed SATA_*_REG macros.
While at it:
* Remove needless SATA Status register read from sil_sata_reset_poll().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ->nice0 and ->nice2 ide_drive_t fields are always zero so remove them.
* IDE_NICE_0 and IDE_NICE_2 defines from <linux/hdreg.h> are no longer
used by any kernel code so cover them with #ifndef/#endif __KERNEL__.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Un-static create_proc_ide_drives() and call it from ide_device_add_all().
While at it:
* Rename create_proc_ide_drives() to ide_proc_port_register_devices().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Factor out devices setup from ide_acpi_init() to
ide_acpi_port_init_devices().
* Call ide_acpi_port_init_devices() in ide_device_add_all().
While at it:
* Remove no longer needed 'drive' field from struct ide_acpi_drive_link.
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->port_init_devs method to ide_hwif_t for a host specific
initialization of devices on a port. Call the new method from
ide_port_init_devices().
* Convert ht6560b, qd65xx and opti621 host drivers to use the new
->port_init_devs method.
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use the same bit for IDE_HFLAG_CS5520 and IDE_HFLAG_VDMA host flags
(both are used only by cs5520 host driver currently).
* Add IDE_HFLAG_NO_IO32_BIT host flag and use it instead of ->no_io_32bit
ide_hwif_t field.
* Add IDE_HFLAG_NO_UNMASK_IRQS host flag, then convert dtc2278 and rz1000
host drivers to use it.
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Factor out code for finding ide_hwifs[] slot from ide_register_hw()
to ide_deprecated_find_port().
* Convert bast-ide, ide-cs and delkin_cb host drivers to use ide_device_add()
instead of ide_register_hw() (while at it drop doing "ide_unregister()" loop
which tries to unregister _all_ IDE interfaces if useable ide_hwifs[] slot
cannot be find).
This patch leaves us with only two ide_register_hw() users:
- drivers/macintosh/mediabay.c
- drivers/ide/ide.c
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add 'init_default' (flag for calling init_hwif_default()) and 'restore'
(flag for calling ide_hwif_restore()) arguments to ide_unregister().
* Update ide_unregister() users to set 'init_default' and 'restore' flags.
* No need to set 'init_default' flag in ide_register_hw() if the setup done
by init_hwif_default() is going to be overridden by ide_init_port_hw().
* No need to set 'init_default' and 'restore' flags in cleanup_module().
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Also, move xfer_func_t typedef to the ide.h since it is used by two drivers
now (more coming).
Bart:
- use __func__ while at it
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->cable_detect method to ide_hwif_t.
* Call the new method in ide_init_port() if:
- the host supports UDMA modes > UDMA2 ('hwif->ultra_mask & 78')
- DMA initialization was successful (if hwif->dma_base is not set
ide_init_port() sets hwif->ultra_mask to zero)
- "idex=ata66" is not used ('hwif->cbl != ATA_CBL_PATA40_SHORT')
* Convert PCI host drivers to use ->cable_detect method.
While at it:
* Factor out cable detection to separate functions (if not already done).
* hpt366.c/it8213.c/slc90e66.c:
- don't check cable type if "idex=ata66" is used
* pdc202xx_new.c:
- add __devinit tag to pdcnew_cable_detect()
* pdc202xx_old.c:
- rename pdc202xx_old_cable_detect() to pdc2026x_old_cable_detect()
- add __devinit tag to pdc2026x_old_cable_detect()
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove 'struct pci_dev *dev' argument from ide_hwif_setup_dma().
* Un-static ide_hwif_setup_dma() and add CONFIG_BLK_DEV_IDEDMA_PCI=n version.
* Add 'const struct ide_port_info *d' argument to ide_device_add[_all]().
* Factor out generic ports init from ide_pci_setup_ports() to ide_init_port(),
move it to ide-probe.c and call it in in ide_device_add_all() instead of
ide_pci_setup_ports().
* Move ->mate setup to ide_device_add_all() from ide_port_init().
* Add IDE_HFLAG_NO_AUTOTUNE host flag for host drivers that don't enable
->autotune currently.
* Setup hwif->chipset in ide_init_port() but iff pi->chipset is set
(to not override setup done by ide_hwif_configure()).
* Add ETRAX host handling to ide_device_add_all().
* cmd640.c: set IDE_HFLAG_ABUSE_* also for CONFIG_BLK_DEV_CMD640_ENHANCED=n.
* pmac.c: make pmac_ide_setup_dma() return an error value and move DMA masks
setup to pmac_ide_setup_device().
* Add 'struct ide_port_info' instances to legacy host drivers, pass them to
ide_device_add() calls and then remove open-coded ports initialization.
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Make ide_build_sglist() and ide_destroy_dmatable() available also when
CONFIG_BLK_DEV_IDEDMA_PCI=n.
* Use ide_build_sglist() and ide_destroy_dmatable() in {ics,au1xxx-}ide.c
and remove no longer needed {ics,au}ide_build_sglist().
There should be no functionality changes caused by this patch.
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Keep pointer to struct device instead of struct pci_dev in ide_hwif_t.
While on it:
* Use *dev->dma_mask instead of pci_dev->dma_mask in ide_toggle_bounce().
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_HFLAG_NO_DSC host flag for hosts that doesn't support DSC overlap.
* Set it in aec62xx (for ATP850UF only) and hpt34x host drivers.
* Convert ide-tape device driver to check for IDE_HFLAG_NO_DSC flag.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Rename 'simplex_stat' variable to 'dma_stat' in ide_get_or_set_dma_base().
* Factor out code for forcing host out of "simplex" mode from
ide_get_or_set_dma_base() to ide_pci_clear_simplex() helper.
* Add IDE_HFLAG_CLEAR_SIMPLEX host flag and set it in alim15x3 (for M5229),
amd74xx (for AMD 7409), cmd64x (for CMD643), generic (for Netcell) and
serverworks (for CSB5) host drivers.
* Make ide_get_or_set_dma_base() test for IDE_HFLAG_CLEAR_SIMPLEX host flag
instead of checking dev->device (BTW the code was buggy because it didn't
check for dev->vendor, luckily none of these PCI Device IDs was used by
some other vendor for PCI IDE controller).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
According to http://marc.info/?l=linux-ide&m=114346138611631, the drivers must
always register 8 DMA ports with ide_setup_dma(), so its last argument is not
needed. While at it, kill some useless parens in that function...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_dump_identify() debug helper for dumping raw identify data in
the hdparm friendly format (== the identify data can be extracted from
dmesg output and passed to hdparm --Istdin).
* Dump identify data in ide-probe.c::do_identify() if DEBUG is enabled.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
After commit 7267c33774
wait_drive_not_busy() can become static again.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
- ide_scan_pcibus() can become static
- instead of ide_scan_pci() we can use ide_scan_pcibus() directly
in module_init()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Based on the earlier work by Tejun Heo.
Switch set_xfer_rate() to use REQ_TYPE_ATA_TASKFILE requests
and make ide_wait_cmd() static.
There should be no functionality changes caused by this patch.
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use wait_drive_not_busy() in drive_cmd_intr().
v2:
* Fix wait_drive_not_busy() comment (noticed by Sergei).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Adrian Bunk