IO-APIC support in the presence of interrupt-remapping infrastructure.
IO-APIC RTE will be programmed with interrupt-remapping table entry(IRTE)
index and the IRTE will contain information about the vector, cpu destination,
trigger mode etc, which traditionally was present in the IO-APIC RTE.
Introduce a new irq_chip for cleaner irq migration (in the process
context as opposed to the current irq migration in the context of an interrupt.
interrupt-remapping infrastructure will help us achieve this cleanly).
For edge triggered, irq migration is a simple atomic update(of vector
and cpu destination) of IRTE and flush the hardware cache.
For level triggered, we need to modify the io-apic RTE aswell with the update
vector information, along with modifying IRTE with vector and cpu destination.
So irq migration for level triggered is little bit more complex compared to
edge triggered migration. But the good news is, we use the same algorithm
for level triggered migration as we have today, only difference being,
we now initiate the irq migration from process context instead of the
interrupt context.
In future, when we do a directed EOI (combined with cpu EOI broadcast
suppression) to the IO-APIC, level triggered irq migration will also be
as simple as edge triggered migration and we can do the irq migration
with a simple atomic update to IO-APIC RTE.
TBD: some tests/changes needed in the presence of fixup_irqs() for
level triggered irq migration.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Interrupt-remapping enables queued invalidation. And once queued invalidation
is enabled, IOTLB invalidation also needs to use the queued invalidation
mechanism and the register based IOTLB invalidation doesn't work.
For now, Support for IOTLB invalidation using queued invalidation is
missing. Meanwhile, disable DMA-remapping, if Interrupt-remapping
support is detected.
For the meanwhile, if someone wants to really enable DMA-remapping, they
can use nox2apic, which will disable interrupt-remapping and as such
doesn't enable queued invalidation.
And given that none of the release platforms support intr-remapping yet,
we should be ok for this temporary hack.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Queued invalidation (part of Intel Virtualization Technology for
Directed I/O architecture) infrastructure.
This will be used for invalidating the interrupt entry cache in the
case of Interrupt-remapping and IOTLB invalidation in the case
of DMA-remapping.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Allocate the iommu during the parse of DMA remapping hardware
definition structures. And also, introduce routines for device
scope initialization which will be explicitly called during
dma-remapping initialization.
These will be used for enabling interrupt remapping separately from the
existing DMA-remapping enabling sequence.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Clean up the intel-iommu code related to deferred iommu flush logic. There is
no need to allocate all the iommu's as a sequential array.
This will be used later in the interrupt-remapping patch series to
allocate iommu much early and individually for each device remapping
hardware unit.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
code reorganization of the generic Intel vt-d parsing related routines and linux
iommu routines specific to Intel vt-d.
drivers/pci/dmar.c now contains the generic vt-d parsing related routines
drivers/pci/intel_iommu.c contains the iommu routines specific to vt-d
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: akpm@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: andi@firstfloor.org
Cc: ebiederm@xmission.com
Cc: jbarnes@virtuousgeek.org
Cc: steiner@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
want to remove arch_get_ram_range, and use early_node_map instead.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It seems VT3336 can't do msi either as with its bro 3351. Disable it.
Reported in the following SUSE bug.
https://bugzilla.novell.com/show_bug.cgi?id=300001
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During the development of the physical PCI slot patch series, Gary Hade
kept on reporting strange oopses due to interactions between pci_slot
and acpiphp.
http://lkml.org/lkml/2007/11/28/319
find_root_bridges() unconditionally installs
handle_hotplug_event_bridge() as an ACPI_SYSTEM_NOTIFY handler for all
root bridges.
However, during module cleanup, remove_bridge() will only remove the
notify handler iff the root bridge had a hot-pluggable slot directly
underneath. That is:
root bridge -> hotplug slot
But, if the topology looks like either of the following:
root bridge -> non-hotplug slot
root bridge -> p2p bridge -> hotplug slot
Then we currently do not remove the notify handler from that root
bridge.
This can cause a kernel oops if we modprobe acpiphp later and it gets
loaded somewhere else in memory. If the root bridge then receives a
hotplug event, it will then attempt to call a stale, non-existent notify
handler and we blow up.
Much thanks goes to Gary Hade for his persistent debugging efforts.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
For Broadcom 5706, 5708, 5709 rev. A nics, any read beyond the
VPD end tag will hang the device. This problem was initially
observed when a vpd entry was created in sysfs
('/sys/bus/pci/devices/<id>/vpd'). A read to this sysfs entry
will dump 32k of data. Reading a full 32k will cause an access
beyond the VPD end tag causing the device to hang. Once the device
is hung, the bnx2 driver will not be able to reset the device.
We believe that it is legal to read beyond the end tag and
therefore the solution is to limit the read/write length.
A majority of this patch is from Matthew Wilcox who gave code for
reworking the PCI vpd size information. A PCI quirk added for the
Broadcom NIC's to limit the read/write's.
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Some PCI devices will lock up if we attempt to read from VPD addresses
beyond some device-dependent limit. Until we can identify these
devices and adjust the file size accordingly, only let root read VPD
through sysfs to prevent a DoS by normal users.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
For the ranges with IORESOURCE_PREFETCH, export a new resource_wc interface in
pci /sysfs along with resource (which is uncached).
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When Greg "fixed" the sysfs usage of that driver a while back, he seem
to have introduced a bug where the quotes are added around the name of
our specific sysfs files, thus breaking the user space tool.
This fixes it. Tested DLPAR operations on a POWER6 machine successfully.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Some (broken?) platform assign the same slot name to multiple hotplug
slots. On such system, slot initialization would fail because of name
collision. The pciehp driver already have a "slot_with_bus" module
option which adds the bus number into the slot name. This patch adds
the message about this module option that will be displayed when slot
name collision is detected.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix the following errors reported by Jan C. Nordholz in
http://bugzilla.kernel.org/show_bug.cgi?id=10751.
kobject_add_internal failed for 2 with -EEXIST, don't try to register things with the same name in the same directory.
Pid: 1, comm: swapper Tainted: G W 2.6.26-rc3 #1
[<c0266980>] kobject_add_internal+0x140/0x190
[<c0266afd>] kobject_init_and_add+0x2d/0x40
[<c027bc91>] pci_hp_register+0x81/0x2f0
[<c027fd07>] pciehp_probe+0x1a7/0x470
[<c01b3b84>] sysfs_add_one+0x44/0xa0
[<c01b3c1f>] sysfs_addrm_start+0x3f/0xb0
[<c01b497a>] sysfs_create_link+0x8a/0xf0
[<c0279570>] pcie_port_probe_service+0x50/0x80
[<c02e0545>] driver_sysfs_add+0x55/0x70
[<c02e0662>] driver_probe_device+0x82/0x180
[<c02e07cc>] __driver_attach+0x6c/0x70
[<c02dfe0a>] bus_for_each_dev+0x3a/0x60
[<c05db2d0>] pcied_init+0x0/0x80
[<c02e04e6>] driver_attach+0x16/0x20
[<c02e0760>] __driver_attach+0x0/0x70
[<c02e0341>] bus_add_driver+0x1a1/0x220
[<c05db2d0>] pcied_init+0x0/0x80
[<c02e09cd>] driver_register+0x4d/0x120
[<c05db050>] ibm_acpiphp_init+0x0/0x190
[<c0125aab>] printk+0x1b/0x20
[<c05db2d0>] pcied_init+0x0/0x80
[<c05db2de>] pcied_init+0xe/0x80
[<c05c751a>] kernel_init+0x10a/0x300
[<c0120138>] schedule_tail+0x18/0x50
[<c0103b9a>] ret_from_fork+0x6/0x1c
[<c05c7410>] kernel_init+0x0/0x300
[<c05c7410>] kernel_init+0x0/0x300
[<c010485b>] kernel_thread_helper+0x7/0x1c
=======================
pci_hotplug: Unable to register kobject '2'<3>pciehp: pci_hp_register failed with error -22
Slot with the same name can be registered multiple times if shpchp or
pciehp driver is loaded after acpiphp is loaded because ACPI based
hotplug driver and Native OS hotplug driver trying to handle the same
physical slot. In this case, current pci_hotplug core will call
kobject_init_and_add() muliple time with the same name. This is the
cause of this problem. To fix this problem, this patch adds the check
into pci_hp_register() to see if the slot with the same name.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
According to the PCI Express specification, we must wait for at least
1 second after turning power off before taking any action that relies
on power having been removed from the slot/adapter. For this, current
pciehp wait for 1 second after issuing the power off command in
hpc_power_off_slot() function. But waiting for 1 second in
hpc_power_off_slot() can make pciehp probing slow-down because pciehp
probe code calls hpc_power_off_slot() if the slot is not occupied just
in case. We don't need to wait for 1 second at the pciehp probe time
because there is no action on that empty slot. So move 1 second wait
from hpc_power_off_slot() to the caller of hpc_power_off_slot().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix improper long wait for command completion in pciehp probing.
As described in PCI Express specification, software notification is
not generated if the command that occurs as a result of a write to the
Slot Control register that disables software notification of command
completed events. Since pciehp driver doesn't take it into account,
such command is issued in pciehp probing, and it causes improper long
wait for command completion.
This patch changes the pciehp driver to take such command into
account.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix the "pciehp probing slow" problem reported from Jan C. Nordholz in
http://bugzilla.kernel.org/show_bug.cgi?id=10751.
The command completed bit in Slot Status register applies only to
commands issued to control the attention indicator, power indicator,
power controller, or electromechanical interlock. However, writes to
other parts of the Slot Control register would end up writing to the
control fields. Hence, any write to Slot Control register is
considered as a command. However, if the controller doesn't support
any of attention indicator, power indicator, power controller and
electromechanical interlock, command completed bit would not set in
writing to Slot Control register. In this case, we should not wait for
command completed bit set, otherwise all commands would be considered
not completed in timeout seconds (1 sec.).
The cause of the problem is pciehp driver didn't take this situation
into account. This patch changes pciehp to take it into account. This
patch also add the check for "No Command Completed Support" bit in
Slot Capability register. If it is set, we should not wait for command
completed bit set as well.
This problem seems to be revealed by the commit
c27fb883df that fixed the bug that
pciehp did not wait for command completed properly (pciehp just
ignored the command completion event).
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Some (broken?) platform assign the same slot name to multiple hotplug
slots. On such system, slot initialization would fail because of name
collision. The shpchp driver already have a "slot_with_bus" module
option which adds the bus number into the slot name. This patch adds
the message about this module option that will be displayed when slot
name collision is detected.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
to make sure get one online node.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The Slot 03:00.* of JMicron controller has two functions, but one is
PCIE endpoint the other isn't PCIE device, very strange. PCIE spec
defines all functions should have the same config for ASPM, so disable
ASPM for the whole slot in this case.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Everybody wants to pass it a function pointer, and in fact, that is what
you _must_ pass it for it to make sense (since it knows that ia64 and
ppc64 use descriptors for function pointers and fetches the actual
address from there).
So don't make the argument be a 'unsigned long' and force everybody to
add a cast.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The acpi_query_osc() function can be called for the ACPI object that
doesn't have _OSC method. In this case, acpi_get_osc_data() would
allocate a useless memory region. To avoid this, we need to check the
existence of _OSC before calling acpi_get_osc_data() in acpi_query_osc().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This applies the NVidia MSI enabled flag for HT capable devices quirk
to ALi bridges as well.
As described in more detail in http://bugzilla.kernel.org/show_bug.cgi?id=10667
this is required for my board which is using an nForce 3 250Gb chipset with an
ALi M1695 northbridge.
It fixes a regression introduced in 2.6.24 that made the internal NIC of the
board unusable (MSI initialisation of the NIC but disabled MSI on the
northbridge devices.
Signed-off-by: Björn Krombholz <fox.box@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The following patch changes the intel-iommu.c code to use the TSC
instead of jiffies for detecting bad DMAR functionality. Some systems
with bad bios's have been seen to hang in early boot spinning in the
IOMMU_WAIT_IO macro. This patch will replace the infinite loop with a call to
panic.
Signed-off-by: Mark Gross <mgross@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The pci_osc_control_set() function can be called for the ACPI object
that doesn't have _OSC method. In this case, acpi_get_osc_data() would
allocate a useless memory region. To avoid this, we need to check the
existence of _OSC before calling acpi_get_osc_data(). Here is a patch
to fix this problem in pci_osc_control_set.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
There is an IA64 system here which have two pci root bridges with _OSC.
One _OSC disables SHPC control bit but the other not. Below patch makes
_OSC data per-device instead of one global, otherwise linux takes both
root bridges don't support SHPC.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix uninitialized variable in __pci_osc_support_set().
If the ACPI namespace doesn't have any device object corresponding to
the specified hid, 'retval' in __pci_osc_support_set() is not changed
by the acpi_query_osc() callback. Since 'retval' is not initizlized in
the current implementation, the contents of 'retval' is undefined in
this case. This causes a mis-handling of ctrlset_buf[OSC_SUPPORT_TYPE]
and will cause an unexpected result in the subsequent
pci_osc_control_set() call as a result.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
so let pci_cfg_space_size call it directly without flag.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (21 commits)
pciehp: fix error message about getting hotplug control
pci/irq: let pci_device_shutdown to call pci_msi_shutdown v2
pci/irq: restore mask_bits in msi shutdown -v3
doc: replace yet another dev with pdev for consistency in DMA-mapping.txt
PCI: don't expose struct pci_vpd to userspace
doc: fix an incorrect suggestion to pass NULL for PCI like buses
Consistently use pdev as the variable of type struct pci_dev *.
pciehp: Fix command write
shpchp: fix slot name
make pciehp_acpi_get_hp_hw_control_from_firmware()
pciehp: Clean up pcie_init()
pciehp: Mask hotplug interrupt at controller release
pciehp: Remove useless hotplug interrupt enabling
pciehp: Fix wrong slot capability check
pciehp: Fix wrong slot control register access
pciehp: Add missing memory barrier
pciehp: Fix interrupt event handlig
pciehp: fix slot name
Update MAINTAINERS with location of PCI tree
PCI: Add Intel SCH PCI IDs
...
People are confused by the following error message that actually is
not for indicating a error.
Cannot get control of hotplug hardware for pci %s
This patch changes this message to debug message.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@hobbes.lan>
[PATCH 2/2] pci/irq: let pci_device_shutdown to call pci_msi_shutdown v2
this change
| commit 23a274c8a5
| Author: Prakash, Sathya <sathya.prakash@lsi.com>
| Date: Fri Mar 7 15:53:21 2008 +0530
|
| [SCSI] mpt fusion: Enable MSI by default for SAS controllers
|
| This patch modifies the driver to enable MSI by default for all SAS chips.
|
| Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
| Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
Causes the kexec of a RHEL 5.1 kernel to fail.
root casue: the rhel 5.1 kernel still uses INTx emulation. and
mptscsih_shutdown doesn't call pci_disable_msi to reenable INTx on kexec path
So call pci_msi_shutdown in the shutdown path to do the same thing to msix
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@hobbes.lan>
[PATCH 1/2] pci/irq: restore mask_bits in msi shutdown -v3
Yinghai found that kexec'ing a RHEL 5.1 kernel with 2.6.25-rc3+ kernels
prevents his NIC from working. He bisected to
| commit 89d694b9db
| Author: Thomas Gleixner <tglx@linutronix.de>
| Date: Mon Feb 18 18:25:17 2008 +0100
|
| genirq: do not leave interupts enabled on free_irq
|
| The default_disable() function was changed in commit:
|
| 76d2160147
| genirq: do not mask interrupts by default
|
For MSI, default_shutdown will call mask_bit for msi device. All mask bits
will left disabled after free_irq. Then in the kexec case, the next kernel
can only use msi_enable bit, so all device's MSI can not be used.
So lets to restore the mask bit to its pci reset defined value (enabled) when
we disable the kernels use of msi to be a little friendlier to kexec'd kernels.
Extend msi_set_mask_bit to msi_set_mask_bits to take mask, so we can fully
restore that to 0x00 instead of 0xfe.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@hobbes.lan>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86-bigbox-pci:
x86: add pci=check_enable_amd_mmconf and dmi check
x86: work around io allocation overlap of HT links
acpi: get boot_cpu_id as early for k8_scan_nodes
x86_64: don't need set default res if only have one root bus
x86: double check the multi root bus with fam10h mmconf
x86: multi pci root bus with different io resource range, on 64-bit
x86: use bus conf in NB conf fun1 to get bus range on, on 64-bit
x86: get mp_bus_to_node early
x86 pci: remove checking type for mmconfig probe
x86: remove unneeded check in mmconf reject
driver core: try parent numa_node at first before using default
x86: seperate mmconf for fam10h out from setup_64.c
x86: if acpi=off, force setting the mmconf for fam10h
x86_64: check MSR to get MMCONFIG for AMD Family 10h
x86_64: check and enable MMCONFIG for AMD Family 10h
x86_64: set cfg_size for AMD Family 10h in case MMCONFIG
x86: mmconf enable mcfg early
x86: clear pci_mmcfg_virt when mmcfg get rejected
x86: validate against acpi motherboard resources
Fixed up fairly trivial conflicts in arch/x86/pci/{init.c,pci.h} due to
OLPC support manually.
Use proc_create()/proc_create_data() to make sure that ->proc_fops and ->data
be setup before gluing PDE to main tree.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Peter Osterlund <petero2@telia.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Neil Brown <neilb@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove proc_bus export and variable itself. Using pathnames works fine
and is slightly more understandable and greppable.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
scan AMD opteron io/mmio routing to make sure every pci root bus get correct
resource range. Thus later pci scan could assign correct resource to device
with unassigned resource.
this can fix a system without _CRS for multi pci root bus.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
in the device_add, we try to use use parent numa_node.
need to make sure pci root bus's bridge device numa_node is set.
then we could use device->numa_node direclty for all device.
and don't need to call pcibus_to_node().
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
reuse pci_cfg_space_size but skip check pci express and pci-x CAP ID.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Current implementation of pciehp_write_cmd() always enables command
completed interrupt. But pciehp_write_cmd() is also used for clearing
command completed interrupt enable bit. In this case, we must not set
the command completed interrupt enable bit. To fix this bug, this
patch add the check to see if caller wants to change command complete
interrupt enable bit.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Suresh Siddha