During a rescan operation mmc_attach(sd|mmc|sdio) functions are
called. The error handling in these function can trigger a detach
of the bus, which also meant a power off. This is not notified by
the rescan operation which then continues to the next attach function.
If a power off has been done, the framework must never send any
new commands to the host driver, without first doing a new power up.
This will most likely trigger any host driver to hang.
Moving power off out of detach and instead handle power off
separately when it is actually needed, solves the issue.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently if card_power_gpio is passed from platform data, it is acquired
and its value is either set or reset. After that we overwrite it with 1,
which is not required.
So, this patch removes the extra line which sets its value.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Freescale eSDHC registers only support 32-bit accesses, this patch
ensures that all Freescale eSDHC register accesses are 32-bit.
Signed-off-by: Xu lei <B33228@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Put MMC to sleep if it supports SLEEP/AWAKE (CMD5) in the mmc suspend
so that Vcc (NAND core) can be cut to minimize power consumption.
eMMC put into SLEEP can respond to CMD0 or H/W reset or CMD5.
Current implemention on resume from suspend relies on CMD0 in
mmc_init_card to get out of SLEEP mode.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Venkatraman S <svenkatr@ti.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The default controller configuration which was previously setup by
platform helper functions is moved into the driver.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Stress-testing the runtime power management of libertas_sdio
through a rmmod/insmod loop revealed that it is quite easy to
cause an ETIMEDOUT failure in mmc_sdio_power_restore() leading to:
libertas_sdio: probe of mmc1:0001:1 failed with error -16
Experimentation shows that a very short delay (100us) is needed in
the power down path before the card can be successfully booted again.
We know that this setup is lacking poweroff clamps on the card's power
lines, but as only a short delay is needed, apply this unconditionally.
Also bump up to 1ms sleep for extra legroom.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The previous patch which implemented a DT binding for sdhci-tegra did not
allow all platform data fields to be initialized from DT. The following
were missing:
is_8bit: Implemented by this patch.
pm_flags: Not implemented yet. There are no mainline users of this field.
I'm not quite sure what it's for, and hence how to represent this
in DT; the value ends up being assigned to host->mmc->pm_caps.
While we're at it, fix the binding documentation to refer to "SD/MMC"
instead of "eSDHC", since that's the correct name; "eSDHC" was cut/paste
from the Freescale binding docs.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The Patch adds the support for SDIO interrupts for all slots.
It includes enabling of SDIO interrupts through dw_mci_enable_sdio_irq
and the handling of the slot specific interrupts in the Interrupt Service
Routine.
Signed-off-by: Shashidhar Hiremath <shashidharh@vayavyalabs.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
If DMA resource is not available then SDCC driver
should atleast work in PIO data transfer mode.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Intialize busclk_timer before it is accessed in probe.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Not all targets have IRQ1 line routed from the SD controller to
the processor. So we cannot rely on IRQ1 for PIO interrupts.
This patch moves all PIO interrupts to IRQ0 and enables the PIO
mode.
Signed-off-by: Murali Palnati <palnatim@codeaurora.org>
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
On some targets, MCI_IRQ_MASK1 is not routed to the MSM in which
case only "cmd_irq" must be used even for PIO. With this change,
all the targets will use only "cmd_irq" for both CMD and PIO.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
For clocks that support rates which can be set (most clocks other
than _pclk AHB clocks), a rate must be set using clk_set_rate()
before the clock is enabled for the first time with clk_enable().
Subsequent calls to clk_enable() need not be preceded with the
clk_set_rate() calls unless we wish to change the clock rate that
is set previously.
SDC host->clk is currently enabled without setting the clock rate
even once. This patch fixes this, by ensuring that the clock rate
for this clock is first set before enabling the clock.
Signed-off-by: Murali Palnati <palnatim@codeaurora.org>
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This allows boards with non-standard sdio cards to fill the CIS/CCCR data.
It is particularly important for old msm72k boards using wl1251.
Also drop the obsolete embedded_sdio_data structure from the header
as it was intended to surve a similiar purpose but was not implemented.
Signed-off-by: Alexander Tarasikov <alexander.tarasikov@gmail.com>
Acked-by: Sahitya Tummala <stummala@codeaurora.org>
[davidb: minor formatting cleanup]
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The use of && instead of || caused a NULL pointer dereference if
gpio setup was not passed via platform data
Signed-off-by: Alexander Tarasikov <alexander.tarasikov@gmail.com>
Acked-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Allow named IRQs to use corresponding specific handlers. If named IRQs are
used, at least an "sdcard" IRQ has to be specified by the platform. If
names are not used, an arbitrary number of IRQs can be provided by the
platform, in which case the generic ISR will be used for each of them.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
[g.liakhovetski@gmx.de: style and typo corrections, platform data check]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Provide separate interrupt handlers which may be used by platforms where
SDHI has three interrupt sources.
This patch also removes the commented-out handling of CRC and other errors.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
This avoids the need to look up the masks each time an interrupt is handled.
As suggested by Guennadi.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fix the sparse warning output "warning: Using plain integer as NULL pointer"
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fix the sparse warning "drivers/mmc/card/queue.c:111:20: warning:
symbol 'mmc_alloc_sg' was not declared. Should it be static?"
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The individual SoC dependency in Kconfig hardly scales anymore.
Instead of having such a fine grained dependency just depend
on ARCH_MXC and risk that the uninformed user has to look in
the help text to figure out which driver is the correct one.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add hooks to read gpio configuration out of the device tree node.
[grant.likely: Rewrite of original patch from John Bonesio]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
[swarren: Fixed tegra_sdhci_get_ro() to retrieve pdata correctly]
[swarren: Reworked to avoid #ifdef CONFIG_OF]
[swarren: Reworked binding based on fsl-imx-esdhc.txt]
[swarren: Documented binding]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Now that we have improved the runtime power management powerup/powerdown
code, we believe that MMC_CAP_POWER_OFF_CARD is no longer necessary:
runtime PM should now work everywhere.
The only hard evidence for introducing MMC_CAP_POWER_OFF_CARD was the
Marvell sd8686 wifi chip, which was believed to require external gpio
manipulation which wasn't supported by some boards.
After further investigation it was realized (and confirmed by Marvell
folks) that sd8686 requirements can be fulfilled by changing the reset
sequence itself, even if no external gpio is manipulated.
For further information, see the following thread:
http://www.mail-archive.com/linux-mmc@vger.kernel.org/msg04289.html
Enable this trivially for a release or two. If no problems are reported,
we will follow up with a more extensive patch to remove this flag
altogether. If problems are reported, we can look at whitelist/blacklist
possibilities as before.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This adds support to inject data errors after a completed host transfer.
The mmc core will return error even though the host transfer is successful.
This simple fault injection proved to be very useful to test the
non-blocking error handling in the mmc_blk_issue_rw_rq().
Random faults can also test how the host driver handles pre_req()
and post_req() in case of errors.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Eanble the ADMA2 mode for freescale esdhc imx driver, tested on MX25
3DS board, MX51 BBG board and MX53 LOCO board.
This patch is only used to enable the ADMA2 for MX51/53 platforms.
MX25/35 can't support the ADMA2 mode, set BROKEN_ADMA quirk on
MX25/35 platforms.
The ADMA mode supported or not can be distinguished by bit 20 of
the Capability Register (offset 0x40) in the FSL eSDHC module.
Signed-off-by: Richard Zhu <richard.zhu@linaro.org>
Tested-and-acked-by: Eric Miao <eric.miao@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Remove the use of irq_to_gpio() in the card detection interrupt
handler. The information is available in the board structure and
we can avoid using a function that has little meaning.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch fixes a potential issue about PDC interrupts. For example we
have a ENDRX pending interrupt and a RXBUFF pending interrupt. We have
received the RXBUFF interrupt but the transfer is not finished (so we
didn't have time to give a new buffer to the PDC controller). Then we
will compute ENDRX interrupt and we will give a new buffer to the PDC
controller, just after we will compute the RXBUFF interrupt and give
one or two new buffers to the PDC controller but we are not sure that
the first buffer given has been filled. So in this situation we may
have "lost" one sg buffer. It's the same for transmission.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Assuming that a sg buffer size is a page size is false so use sg_dma_len.
A 4096 bytes can be required with two 2048-bytes sg buffer.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Rename atmci_start_command() to atmci_send_command() which is more
appropriate; atmci_start_command suggests we're sending a start command.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add pdc support for atmel-mci. It makes at91-mci driver useless because it
was only used for the old atmel MCI core which has pdc but no dma support.
To allow removing at91-mci, the capabilities of the MCI core are detected
at runtime -- then the driver will use pio, pdc or dma transfers.
Warning: at91rm9200 is not supported, to support it we need to use swab32
on data but I have no board to test it.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Change atmci_readl and atmci_writel macros: remove string concatenation.
We can use these macros with registers which are not prefixed by ATMCI_.
This is the case if we want to write PDC registers which are common to
several devices so they are not prefixed with ATMCI_.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
* 'for-linus' of git://git.kernel.dk/linux-block:
floppy: use del_timer_sync() in init cleanup
blk-cgroup: be able to remove the record of unplugged device
block: Don't check QUEUE_FLAG_SAME_COMP in __blk_complete_request
mm: Add comment explaining task state setting in bdi_forker_thread()
mm: Cleanup clearing of BDI_pending bit in bdi_forker_thread()
block: simplify force plug flush code a little bit
block: change force plug flush call order
block: Fix queue_flag update when rq_affinity goes from 2 to 1
block: separate priority boosting from REQ_META
block: remove READ_META and WRITE_META
xen-blkback: fixed indentation and comments
xen-blkback: Don't disconnect backend until state switched to XenbusStateClosed.
This patch fixes the problem in sdhci-s3c host driver for Samsung Soc's.
During the card identification stage the mmc core driver enumerates for
the best bus width in combination with the highest available data rate.
It starts enumerating from the highest bus width (8) to lowest width (1).
In case of few MMC cards the 4-bit bus enumeration fails and tries
the 1-bit bus enumeration. When switched to 1-bit bus mode the host driver
has to clear the previous bus width setting and apply the new setting.
The current patch will clear the previous bus mode and apply the new
mode setting.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc_sd_init_uhs_card function sets the driver type, current limit
and bus speed mode on card as well as on host controller side.
Currently bus speed mode is set by sending CMD6 to card and
immediately setting the timing mode in host controller. But
then before initiating tuning sequence, it also tries to set
current limit by sending CMD6 to card which results in data
timeout errors in controller if bus speed mode is SDR50/SDR104 mode.
So basically bus speed mode should be set only after current limit
is set in the card and immediately after setting the bus speed mode,
tuning sequence should be initiated.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This corrects a logic error that I introduced in
"mmc: sdhi: Add write16_hook"
Reported-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
The default multithread workqueue can cause the same work to be executed
concurrently on a different CPUs. This isn't really suitable for clock
gating as it might already gated the clock and gating it twice results both
host->clk_old and host->ios.clock to be set to 0.
To prevent this from happening we use system_nrt_wq instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Chris Ball <cjb@laptop.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
We have seen at least two different races when clock gating kicks in in a
middle of ios structure update.
First one happens when ios->clock is changed outside of aggressive clock
gating framework, for example via mmc_set_clock(). The race might happen
when we run following code:
mmc_set_ios():
...
if (ios->clock > 0)
mmc_set_ungated(host);
Now if gating kicks in right after the condition check we end up setting
host->clk_gated to false even though we have just gated the clock. Next
time a request is started we try to ungate and restore the clock in
mmc_host_clk_hold(). However since we have host->clk_gated set to false the
original clock is not restored.
This eventually will cause the host controller to hang since its clock is
disabled while we are trying to issue a request. For example on Intel
Medfield platform we see:
[ 13.818610] mmc2: Timeout waiting for hardware interrupt.
[ 13.818698] sdhci: =========== REGISTER DUMP (mmc2)===========
[ 13.818753] sdhci: Sys addr: 0x00000000 | Version: 0x00008901
[ 13.818804] sdhci: Blk size: 0x00000000 | Blk cnt: 0x00000000
[ 13.818853] sdhci: Argument: 0x00000000 | Trn mode: 0x00000000
[ 13.818903] sdhci: Present: 0x1fff0000 | Host ctl: 0x00000001
[ 13.818951] sdhci: Power: 0x0000000d | Blk gap: 0x00000000
[ 13.819000] sdhci: Wake-up: 0x00000000 | Clock: 0x00000000
[ 13.819049] sdhci: Timeout: 0x00000000 | Int stat: 0x00000000
[ 13.819098] sdhci: Int enab: 0x00ff00c3 | Sig enab: 0x00ff00c3
[ 13.819147] sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000
[ 13.819196] sdhci: Caps: 0x6bee32b2 | Caps_1: 0x00000000
[ 13.819245] sdhci: Cmd: 0x00000000 | Max curr: 0x00000000
[ 13.819292] sdhci: Host ctl2: 0x00000000
[ 13.819331] sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x00000000
[ 13.819377] sdhci: ===========================================
[ 13.919605] mmc2: Reset 0x2 never completed.
and it never recovers.
Second race might happen while running mmc_power_off():
static void mmc_power_off(struct mmc_host *host)
{
host->ios.clock = 0;
host->ios.vdd = 0;
[ clock gating kicks in here ]
/*
* Reset ocr mask to be the highest possible voltage supported for
* this mmc host. This value will be used at next power up.
*/
host->ocr = 1 << (fls(host->ocr_avail) - 1);
if (!mmc_host_is_spi(host)) {
host->ios.bus_mode = MMC_BUSMODE_OPENDRAIN;
host->ios.chip_select = MMC_CS_DONTCARE;
}
host->ios.power_mode = MMC_POWER_OFF;
host->ios.bus_width = MMC_BUS_WIDTH_1;
host->ios.timing = MMC_TIMING_LEGACY;
mmc_set_ios(host);
}
If the clock gating worker kicks in while we are only partially updated the
ios structure the host controller gets incomplete ios and might not work as
supposed. Again on Intel Medfield platform we get:
[ 4.185349] kernel BUG at drivers/mmc/host/sdhci.c:1155!
[ 4.185422] invalid opcode: 0000 [#1] PREEMPT SMP
[ 4.185509] Modules linked in:
[ 4.185565]
[ 4.185608] Pid: 4, comm: kworker/0:0 Not tainted 3.0.0+ #240 Intel Corporation Medfield/iCDKA
[ 4.185742] EIP: 0060:[<c136364e>] EFLAGS: 00010083 CPU: 0
[ 4.185827] EIP is at sdhci_set_power+0x3e/0xd0
[ 4.185891] EAX: f5ff98e0 EBX: f5ff98e0 ECX: 00000000 EDX: 00000001
[ 4.185970] ESI: f5ff977c EDI: f5ff9904 EBP: f644fe98 ESP: f644fe94
[ 4.186049] DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
[ 4.186125] Process kworker/0:0 (pid: 4, ti=f644e000 task=f644c0e0 task.ti=f644e000)
[ 4.186219] Stack:
[ 4.186257] f5ff98e0 f644feb0 c1365173 00000282 f5ff9460 f5ff96e0 f5ff96e0 f644feec
[ 4.186418] c1355bd8 f644c0e0 c1499c3d f5ff96e0 f644fed4 00000006 f5ff96e0 00000286
[ 4.186579] f644fedc c107922b f644feec 00000286 f5ff9460 f5ff9700 f644ff10 c135839e
[ 4.186739] Call Trace:
[ 4.186802] [<c1365173>] sdhci_set_ios+0x1c3/0x340
[ 4.186883] [<c1355bd8>] mmc_gate_clock+0x68/0x120
[ 4.186963] [<c1499c3d>] ? _raw_spin_unlock_irqrestore+0x4d/0x60
[ 4.187052] [<c107922b>] ? trace_hardirqs_on+0xb/0x10
[ 4.187134] [<c135839e>] mmc_host_clk_gate_delayed+0xbe/0x130
[ 4.187219] [<c105ec09>] ? process_one_work+0xf9/0x5b0
[ 4.187300] [<c135841d>] mmc_host_clk_gate_work+0xd/0x10
[ 4.187379] [<c105ec82>] process_one_work+0x172/0x5b0
[ 4.187457] [<c105ec09>] ? process_one_work+0xf9/0x5b0
[ 4.187538] [<c1358410>] ? mmc_host_clk_gate_delayed+0x130/0x130
[ 4.187625] [<c105f3c8>] worker_thread+0x118/0x330
[ 4.187700] [<c1496cee>] ? preempt_schedule+0x2e/0x50
[ 4.187779] [<c105f2b0>] ? rescuer_thread+0x1f0/0x1f0
[ 4.187857] [<c1062cf4>] kthread+0x74/0x80
[ 4.187931] [<c1062c80>] ? __init_kthread_worker+0x60/0x60
[ 4.188015] [<c149acfa>] kernel_thread_helper+0x6/0xd
[ 4.188079] Code: 81 fa 00 00 04 00 0f 84 a7 00 00 00 7f 21 81 fa 80 00 00 00 0f 84 92 00 00 00 81 fa 00 00 0
[ 4.188780] EIP: [<c136364e>] sdhci_set_power+0x3e/0xd0 SS:ESP 0068:f644fe94
[ 4.188898] ---[ end trace a7b23eecc71777e4 ]---
This BUG() comes from the fact that ios.power_mode was still in previous
value (MMC_POWER_ON) and ios.vdd was set to zero.
We prevent these by inhibiting the clock gating while we update the ios
structure.
Both problems can be reproduced by simply running the device in a reboot
loop.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Chris Ball <cjb@laptop.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
As per suggestion by Linus Walleij:
> If you think the names of the functions are confusing then
> you may rename them, say like this:
>
> mmc_host_clk_ungate() -> mmc_host_clk_hold()
> mmc_host_clk_gate() -> mmc_host_clk_release()
>
> Which would make the usecases more clear
(This is CC'd to stable@ because the next two patches, which fix
observable races, depend on it.)
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
There are the following warnings and errorx when compiling the driver.
The patch adds the missing inclusion of linux/module.h to fix them.
drivers/mmc/host/sdhci-esdhc-imx.c:563:12: error: ‘THIS_MODULE’ undeclared here (not in a function)
[..]
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add a new REQ_PRIO to let requests preempt others in the cfq I/O schedule,
and lave REQ_META purely for marking requests as metadata in blktrace.
All existing callers of REQ_META except for XFS are updated to also
set REQ_PRIO for now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Host driver can't get a hint of DDR mode through ios->ddr flag anymore.
ios->timing is currently used to inform DDR mode as a substitute.
And capability of MMC_CAP_MMC_HIGHSPEED is added for DDR support.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When timeout_clk is calculated the host->clock could be zero.
So, instead of host->clock the calculation now uses mmc->f_max.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This moves the calculation below the assignment of mmc->f_max, which
we need for calculating timeout_clk in the next patch in this series.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This reverts commit 4b01681c77, which introduced a new potential
divide by zero in the process of fixing one. The subsequent commits
attempt to fix the issue properly.
Signed-off-by: Chris Ball <cjb@laptop.org>
