Several MIPS platforms don't set pci_controller::io_map_base for their
PCI bridges. This results in a panic in pci_iomap(). (The panic is
conditional on CONFIG_PCI_DOMAINS, but that is now enabled for all PCI
MIPS systems.)
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: linux-mips@linux-mips.org
Cc: Martin Michlmayr <tbm@cyrius.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: 584784@bugs.debian.org
Patchwork: https://patchwork.linux-mips.org/patch/1377/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Currently, the eth devices are probed in the inverse order, first
au1xxx_eth1_device and then au1xxx_eth0_device. On the GPR board,
this makes trouble:
# ifconfig|grep HWaddr
eth0 Link encap:Ethernet HWaddr 00:50:C2:0C:30:01
eth1 Link encap:Ethernet HWaddr 66:22:01:80:38:10
A bogous ethernet hwaddr is assigned to the first device and
au1xxx_eth0_device is mapped to eth1, which even does not work
properly. With this patch, the problems are gone:
# ifconfig|grep HWaddr
eth0 Link encap:Ethernet HWaddr 66:22:11:32:38:10
eth1 Link encap:Ethernet HWaddr 66:22:11:32:38:11
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1473/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As a relativly new ABI N32 should only have received the getdents64(2) but
instead it only had getdents(2). This was noticed as a performance anomaly
in glibc.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes a regression introduced by commit "MIPS: Alchemy: MTX-1:
Use linux gpio api." (bb706b28bb) which broke
PCI bus operation. The problem is caused by alchemy_gpio2_enable() which
resets the GPIO2 block. Two PCI signals (PCI_SERR and PCI_RST) are connected
to GPIO2 and they obviously do not to like the reset. Since GPIO2 is
correctly initialized by the boot monitor (YAMON) it is not necessary to
call this function, so just remove it.
Also replace gpio_set_value() with alchemy_gpio_set_value() to avoid
problems in case gpiolib gets initialized after PCI. And since alchemy
gpio_set_value() calls au_sync() we don't have to au_sync() again later.
Signed-off-by: Bruno Randolf <br1@einfach.org>
To: linux-mips@linux-mips.org
To: manuel.lauss@googlemail.com
Patchwork: https://patchwork.linux-mips.org/patch/1448/
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Quoting from Jiri Slaby's patch of a similar nature for x86:
When initrd is in use and a driver does request_module() in its
module_init (i.e. __initcall or device_initcall), a modprobe
process is created with VDSO mapping. But VDSO is inited even in
__initcall, i.e. on the same level (at the same time), so it may
not be inited yet (link order matters).
Move init_vdso up to subsys_initcall to avoid the issue.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Patchwork: http://patchwork.linux-mips.org/patch/1386/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In addition to being useless, it was mis-spelled.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Cc: David Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1385/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The 4600 family code reads registers to differentiate between two ASIC
variants, but this was being done prior to the register setup. This moves
register setup before the reading code.
Signed-off-by: David VomLehn <dvomlehn@cisco.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1392/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Breaking here dropped us to the default code which always sends a SIGILL
to the current process, no matter what the CU2 notifier says.
[Ralf: Currently this only hurts on Cavium and possibly some out of tree
platforms.]
Signed-off-by: Jesper Nilsson <jesper@jni.nu>
To: linux-mips@linux-mips.org
To: linux-kernel@vger.kernel.org
Patchwork: http://patchwork.linux-mips.org/patch/1391/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When trying to netboot a Linksys WRT54GS WLAN router, the bootup fails,
because of following error message:
...
[ 0.424000] b44: b44.c:v2.0
[ 0.424000] b44: Invalid MAC address found in EEPROM
[ 0.432000] b44 ssb0:1: Problem fetching invariants of chip,aborting
[ 0.436000] b44: probe of ssb0:1 failed with error -22
...
The router uses a CFE bootloader, but most of the needed environment
variables for network card initialization, are not available from CFE
via printenv and even though not via cfe_getenv().
The required environment variables are saved in a special partition
in flash memory. The attached patch implement nvram_getenv and enables
bootup via NFS root on my router.
Most of the patch is extracted from the OpenWrt subversion repository and
stripped down and cleaned up to just fix this issue.
[Ralf: sorted out header file inclusions. Lots of unneded headers and such
that should have been included.]
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Reviewed-by: Phil Sutter <phil@nwl.cc>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/1359/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch declare the rtc device present on systems with clock compatible
with the mc146818 and handled by rtc-cmos. Introduce a new Kconfig entry
because there are some systems without rtc_cmos compatible clock.
Signed-off-by: Arnaud Patard <apatard@mandriva.com>
To: linux-mips@linux-mips.org
Cc: aba@not.so.argh.org
Patchwork: http://patchwork.linux-mips.org/patch/1320/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The fragile MT sys_sched_setaffinity wrapper needs its regular dose of
fixes.
Nose-poked-at-pile-o-crap-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When exiting from loongson2_exit(), we need to reset the counter
register too, this patch adds a function reset_counters() to do it, by
the way, this function will be shared by Perf.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1199/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Split the low-level sleepcode into per-cpu functions instead of
relying on compile-time-defined cpu type.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1281/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds an inline function in_module() to check which space the
instruction pointer in, kernel space or module space.
Note: This will not work when the kernel space and module space are the
same. If they are the same, we need to modify scripts/recordmcount.pl,
ftrace_make_nop/call() and the other related parts to ensure the
enabling/disabling of the calling site to _mcount is right for both
kernel and module.
[Ralf: It also is still incorrect for some 64-bit kernels.]
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips <linux-mips@linux-mips.org>
Cc: David Daney <david.s.daney@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/1232/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With the help of uasm this patch encodes the instructions of the dynamic
function tracer in ftrace_dyn_arch_init() when initializing it.
As a result we can remove the dynamic encoding of instructions in
ftrace_make_nop()/call(), ftrace_enable_ftrace_graph_caller() and remove
the macro jump_insn_encode() and at last this reduce the overhead of
dynamic Function Tracer. This also is cleaner.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips <linux-mips@linux-mips.org>
Cc: David Daney <david.s.daney@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/1230/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds some cleanups of the instructions:
o use macros instead of magic numbers
o use macros instead of variables to reduce some overhead
o add new macro for the jal instruction
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips <linux-mips@linux-mips.org>
Cc: David Daney <david.s.daney@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/1229/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For 32-bit kernel the -mmcount-ra-address option of gcc 4.5 emits one
extra instruction before calling to _mcount so we need to use a different
"b 1f" for it.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips <linux-mips@linux-mips.org>
Cc: David Daney <david.s.daney@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/1228/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As documented in the GCC 4.5 docs [1] -mmcount-ra-address uses register
$12 to pass the stack offset of the return address to the _mcount function.
On 64-bit kernels $12 is t0 but in 32-bit kernels it is t4 so we need to
use $12 instead of t0 here to be correct for both kernel types.
[1] GCC documentation: MIPS Options
http://gcc.gnu.org/onlinedocs/gcc/MIPS-Options.html
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips <linux-mips@linux-mips.org>
Cc: David Daney <david.s.daney@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/1227/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The return value of gpio_to_irq() is not a pointer but an integer.
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1280/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Atsushi Nemoto <anemo@mba.ocn.ne.jp> spotted that this had been incorrectly
removed in a previous patch
Signed-off-by: Chris Dearman <chris@mips.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1213/
Tested-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The function _wrmsr() called by divil_lbar_disable()/enable() should be
called with the offset as the argument.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Zhang Le <r0bertz@gentoo.org>
Patchwork: http://patchwork.linux-mips.org/patch/1252/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add several missing RDMSRs for IDE and USB are missing to avoid the
agressive modification of the high 32 bits of the MSR.
Without this patch some usb devices may fail after printing "reset ehci
host ....." when reading the partition information.
Signed-off-by: Hu Hongbing <huhb@lemote.com>
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Zhang Le <r0bertz@gentoo.org>
Cc: Hu Hongbing <huhb@lemote.com>
Patchwork: http://patchwork.linux-mips.org/patch/1250/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
PORT_AR7 has the correct TRIG flag (UART_FCR_R_TRIG_00) as well as
UART_CAP_AFE being set. This fixes UART on TNETD7300 revision 0x02,
which would otherwise mangle some characters, no side effects on
other revisions.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1246/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'for-35' of git://repo.or.cz/linux-kbuild: (81 commits)
kbuild: Revert part of e8d400a to resolve a conflict
kbuild: Fix checking of scm-identifier variable
gconfig: add support to show hidden options that have prompts
menuconfig: add support to show hidden options which have prompts
gconfig: remove show_debug option
gconfig: remove dbg_print_ptype() and dbg_print_stype()
kconfig: fix zconfdump()
kconfig: some small fixes
add random binaries to .gitignore
kbuild: Include gen_initramfs_list.sh and the file list in the .d file
kconfig: recalc symbol value before showing search results
.gitignore: ignore *.lzo files
headerdep: perlcritic warning
scripts/Makefile.lib: Align the output of LZO
kbuild: Generate modules.builtin in make modules_install
Revert "kbuild: specify absolute paths for cscope"
kbuild: Do not unnecessarily regenerate modules.builtin
headers_install: use local file handles
headers_check: fix perl warnings
export_report: fix perl warnings
...
GCC's __builtin_prefetch() was introduced a long time ago, all
supported GCC versions have it. Lets do what the big boys up in
linux/prefetch.h do, except we use '1' as the third parameter to
provoke 'PREF 0,...' and 'PREF 1,...' instead of other prefetch
hints.
This allows for better code generation. In theory the existing
embedded asm could be optimized, but the compiler has these builtins,
so there is really no point.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1235/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For the simulator, fake a slow clock to get fast output.
In prom_putchar we have to mask the value so the simulator doesn't
ASSERT when printing non-ASCII characters.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1255/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
ar7_regiser_devices needs ar7_clocks_init to have been called first,
however clock.o is currently linked later due to its order in the Makefile,
therefore ar7_clocks_init always gets called later than ar7_register_devices
because both have the same initcall level. Fix this by moving
ar7_register_devices to the right initcall level.
Reported-by: Michael J. Evans <mjevans1983@gmail.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
To: linux-mips@linux-mips.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1212/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Instead of doing yet another switch/case on the chip_id, use existing
inline function to set the watchdog base address.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1211/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is too generic a name, so prefix it with BCM63XX_ to avoid potential
namespace clashes when including <asm/gpio.h>.
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1171/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Updates the 4G Systems MTX-1 defconfig, and remove systems unavailable
on this platform. Changes include:
- built-in MTD char/block support
- GPIO sysfs support
- MTX-1 watchdog driver
- I2C over GPIO driver as a module
- SquashFS support
Signed-off-by: Florian Fainelli <florian@openwrt.org>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1168/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The _EXL, _KERNEL etc. bits are in the performance control register so
use _PERFCTRL prefix instead of _PERFCNT. While at it make the macro
more readable, use _ENABLE instead of _INT_EN suffix to describe the
interrupt enable bit.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1203/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Unified macro for counter0 and counter1 to set the event in the control
register. This will be needed by Perf.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1200/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
