Commit aa584ca4 broke what 6cf5be51 had already fixed: there may
be four multifunction devices, but just two pseudo-multifunction
devices per PCMCIA card.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
When the CMI8738 FRAME2 register is read, the chip sometimes (probably
when wrapping around) returns an invalid value that would be outside the
programmed DMA buffer. This leads to an inconsistent PCM pointer that is
likely to result in an underrun.
To work around this, read the register multiple times until we get a
valid value; the error state seems to be very short-lived.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reported-and-tested-by: Matija Nalis <mnalis-alsadev@voyager.hr>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This change makes it so that vlan_gro_receive is only used if vlans have been
registered to the adapter structure. Previously we were just sending all vlan
tagged frames in via this function but this results in a null pointer
dereference when vlans are not registered.
[ This fixes bugzilla entry 15582 -Eric Dumazet]
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously the driver tweaked txqueuelen to avoid false Tx hang reports seen at half duplex.
This had the effect of overriding user set values on link change/reset. Testing shows that
adjusting only the timeout factor is sufficient to prevent Tx hang reports at half duplex.
Based on e1000e patch by Franco Fichtner <franco@lastsummer.de>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't aggregate rx_no_buffer_count into rx_fifo_errors. RNBC counts
packets that get queued temporarily in the adapter's FIFO. These
packets are not dropped and are not errors. The correct counter
is rx_missed_errors (MPC).
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Netpoll needs to call the proper handler depending on the IRQ mode
and the vector.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bnx2 driver calls netif_napi_add() for all the NAPI structs during
->probe() time but not all of them will be used if we're not in MSI-X
mode. This creates a problem for netpoll since it will poll all the
NAPI structs in the dev_list whether or not they are scheduled, resulting
in a crash when we access structure fields not initialized for that vector.
We fix it by moving the netif_napi_add() call to ->open() after the number
of IRQ vectors has been determined.
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When used_dirs was introduced for the flex_groups struct, it looks
like the accounting was not put into place properly, in some places
manipulating free_inodes rather than used_dirs.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
When ext4 driver is used to mount a filesystem instead of the ext3 file
system driver (through CONFIG_EXT4_USE_FOR_EXT23), do not enable delayed
allocation by default since some ext3 users and application writers have
developed unfortunate expectations about the safety of writing files on
systems subject to sudden and violent death without using fsync().
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
In o2dlm, the master of a lock resource keeps a map of all interested
nodes. This prevents the master from purging the resource before an
interested node can create a lock.
A race between the mastery thread and the mastery handler allowed an
interested node to discover who the master is without informing the
master directly. This is easily fixed by holding the dlm spinlock a
little longer in the mastery handler.
Signed-off-by: Srinivas Eeda <srinivas.eeda@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
The rule is that all inodes in the orphan dir have ORPHANED_FL,
otherwise we treated it as an ERROR. This rule works well except
for some rare cases of reflink operation:
http://oss.oracle.com/bugzilla/show_bug.cgi?id=1215
The problem is caused by how reflink and our orphan_scan thread
interact.
* The orphan scan pulls the orphans into a queue first, then runs the
queue at a later time. We only hold the orphan_dir's lock
during scanning.
* Reflink create a oprhaned target in orphan_dir as its first step.
It removes the target and clears the flag as the final step.
These two steps take the orphan_dir's lock, but it is not held for
the duration.
Based on the above semantics, a reflink inode can be moved out of the
orphan dir and have its ORPHANED_FL cleared before the queue of orphans
is run. This leads to a ERROR in ocfs2_query_wipde_inode().
This patch teaches ocfs2_query_wipe_inode() to detect previously
orphaned reflink targets. If a reflink fails or a crash occurs during
the relfink operation, the inode will retain ORPHANED_FL and will be
properly wiped.
Signed-off-by: Tristan Ye <tristan.ye@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Currently, some callers were missing to journal the dirty inode after
adding it to orphan dir.
Now we're going to journal such modifications within the ocfs2_orphan_add()
itself, It's safe to do so, though some existing caller may duplicate this,
and it makes the logic look more straightforward anyway.
Signed-off-by: Tristan Ye <tristan.ye@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
When the local alloc file changes windows, unused bits are freed back to the
global bitmap. By defnition, those bits can not be in use by any file. Also,
the local alloc will never have been able to allocate those bits if they
were part of a previous truncate. Therefore it makes sense that we should
clear unused local alloc bits in the undo buffer so that they can be used
immediatly.
[ Modified to call it ocfs2_release_clusters() -- Joel ]
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
request_resource() and insert_resource() only return success or failure,
which no information about what existing resource conflicted with the
proposed new reservation. This patch adds request_resource_conflict()
and insert_resource_conflict(), which return the conflicting resource.
Callers may use this for better error messages or to adjust the new
resource and retry the request.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
ksz884x: fix return value of netdev_set_eeprom
netdev_set_eeprom() confused ethtool by just returning 1 on error
instead of a proper -EINVAL.
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allows the net_cls cgroup subsystem to be compiled as a module
This patch modifies net/sched/cls_cgroup.c to allow the net_cls subsystem
to be optionally compiled as a module instead of builtin. The
cgroup_subsys struct is moved around a bit to allow the subsys_id to be
either declared as a compile-time constant by the cgroup_subsys.h include
in cgroup.h, or, if it's a module, initialized within the struct by
cgroup_load_subsys.
Signed-off-by: Ben Blum <bblum@andrew.cmu.edu>
Acked-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Paul Menage <menage@google.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I've been getting more and more quirk reports about this. It seems
clear at this point that other OSes are not using this for determining
whether the integrated panel should be turned on, and it is not
reliable for doing so. Better to light up an unintended panel than to
not light up the only usable output on the system.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
On x86 systems using ACPI _CRS information -- now the default for
post-2008 systems -- the PCI root bus no longer pretends to be
offering the root ioport_resource. To avoid accidentally hitting
some platform / system device, use only I/O ports >= 0x100 for
PCMCIA devices on x86.
Reported-by: Komuro <komurojun-mbn@nifty.com>
CC: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
"Input: add KEY_WPS_BUTTON definition" introduced
a generic keycode for WPS input events.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Commit "Input: add KEY_WPS_BUTTON definition"
added a generic keycode for WPS button.
Let's use it, instead of "F1" mapping.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
nilfs_wait_on_logs has a potential to slip out before completion of
all bio requests when it met an error. This synchronization fault may
cause unexpected results, for instance, violative access to freed
segment buffers from an end-bio callback routine.
This fixes the issue by ensuring that nilfs_wait_on_logs waits all
given logs.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
The logarithmic accumulation done in the timekeeping has some overflow
protection that limits the max shift value. That means it will take
more then shift loops to accumulate all of the cycles. This causes
the shift decrement to underflow, which causes the loop to never exit.
The simplest fix would be simply to do a:
if (shift)
shift--;
However that is not optimal, as we know the cycle offset is larger
then the interval << shift, the above would make shift drop to zero,
then we would be spinning for quite awhile accumulating at interval
chunks at a time.
Instead, this patch only decreases shift if the offset is smaller
then cycle_interval << shift. This makes sure we accumulate using
the largest chunks possible without overflowing tick_length, and limits
the number of iterations through the loop.
This issue was found and reported by Sonic Zhang, who also tested the fix.
Many thanks your explanation and testing!
Reported-by: Sonic Zhang <sonic.adi@gmail.com>
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Tested-by: Sonic Zhang <sonic.adi@gmail.com>
LKML-Reference: <1268948850-5225-1-git-send-email-johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
According to the report from Andreas Beckmann (Message-ID:
<4BA54677.3090902@abeckmann.de>), nilfs in 2.6.33 kernel got stuck
after a disk full error.
This turned out to be a regression by log writer updates merged at
kernel 2.6.33. nilfs_segctor_abort_construction, which is a cleanup
function for erroneous cases, was skipping writeback completion for
some logs.
This fixes the bug and would resolve the hang issue.
Reported-by: Andreas Beckmann <debian@abeckmann.de>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Tested-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Cc: stable <stable@kernel.org> [2.6.33.x]
Clear pointer to mds request after dropping the reference to
ensure we don't drop it again, as there is at least one error
path through this function that does not reset fi->last_readdir
to a new value.
Signed-off-by: Sage Weil <sage@newdream.net>
Fix a broken check that a reply came back from the same MDS we sent the
request to. I don't think a case that actually triggers this would ever
come up in practice, but it's clearly wrong and easy to fix.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Sage Weil <sage@newdream.net>
Return ERR_PTR(-ENOMEM) if kmalloc() fails. We handle allocation
failures the same way later in the function.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Sage Weil <sage@newdream.net>
Currently, if the wait_event_interruptible is interrupted, we
return EAGAIN unconditionally and loop, such that we aren't, in
fact, interruptible. So, propagate ERESTARTSYS if we get it.
Signed-off-by: Sage Weil <sage@newdream.net>
We were rebuilding the snap context when it was not necessary
(i.e. when the realm seq hadn't changed _and_ the parent seq
was still older), which caused page snapc pointers to not match
the realm's snapc pointer (even though the snap context itself
was identical). This confused begin_write and put it into an
endless loop.
The correct logic is: rebuild snapc if _my_ realm seq changed, or
if my parent realm's seq is newer than mine (and thus mine needs
to be rebuilt too).
Signed-off-by: Sage Weil <sage@newdream.net>
We get a fault callback on _every_ tcp connection fault. Normally, we
want to reopen the connection when that happens. If the address we have
is bad, however, and connection attempts always result in a connection
refused or similar error, explicitly closing and reopening the msgr
connection just prevents the messenger's backoff logic from kicking in.
The result can be a console full of
[ 3974.417106] ceph: osd11 10.3.14.138:6800 connection failed
[ 3974.423295] ceph: osd11 10.3.14.138:6800 connection failed
[ 3974.429709] ceph: osd11 10.3.14.138:6800 connection failed
Instead, if we get a fault, and have outstanding requests, but the osd
address hasn't changed and the connection never successfully connected in
the first place, do nothing to the osd connection. The messenger layer
will back off and retry periodically, because we never connected and thus
the lossy bit is not set.
Instead, touch each request's r_stamp so that handle_timeout can tell the
request is still alive and kicking.
Signed-off-by: Sage Weil <sage@newdream.net>
Make variable name slightly more generic, since it will (soon)
reflect either the time the request was sent OR the time it was
last determined to be still retrying.
Signed-off-by: Sage Weil <sage@newdream.net>
The messenger fault was clearing the BUSY bit, for reasons unclear. This
made it possible for the con->ops->fault function to reopen the connection,
and requeue work in the workqueue--even though the current thread was
already in con_work.
This avoids a problem where the client busy loops with connection failures
on an unreachable OSD, but doesn't address the root cause of that problem.
Signed-off-by: Sage Weil <sage@newdream.net>
Prevent duplicate 'mds0 caps stale' message from spamming the console every
few seconds while the MDS restarts. Set s_renew_requested earlier, so that
we only print the message once, even if we don't send an actual request.
Signed-off-by: Sage Weil <sage@newdream.net>
The incremental map decoding of pg pool updates wasn't skipping
the snaps and removed_snaps vectors. This caused osd requests
to stall when pool snapshots were created or fs snapshots were
deleted. Use a common helper for full and incremental map
decoders that decodes pools properly.
Signed-off-by: Sage Weil <sage@newdream.net>
The wait_unsafe_requests() helper dropped the mdsc mutex to wait
for each request to complete, and then examined r_node to get the
next request after retaking the lock. But the request completion
removes the request from the tree, so r_node was always undefined
at this point. Since it's a small race, it usually led to a
valid request, but not always. The result was an occasional
crash in rb_next() while dereferencing node->rb_left.
Fix this by clearing the rb_node when removing the request from
the request tree, and not walking off into the weeds when we
are done waiting for a request. Since the request we waited on
will _always_ be out of the request tree, take a ref on the next
request, in the hopes that it won't be. But if it is, it's ok:
we can start over from the beginning (and traverse over older read
requests again).
Signed-off-by: Sage Weil <sage@newdream.net>
We were releasing used caps (e.g. FILE_CACHE) from encode_inode_release
with MDS requests (e.g. setattr). We don't carry refs on most caps, so
this code worked most of the time, but for setattr (utimes) we try to
drop Fscr.
This causes cap state to get slightly out of sync with reality, and may
result in subsequent mds revoke messages getting ignored.
Fix by only releasing unused caps.
Signed-off-by: Sage Weil <sage@newdream.net>
Drop session mutex unconditionally in handle_cap_grant, and do the
check_caps from the handle_cap_grant helper. This avoids using a magic
return value.
Also avoid using a flag variable in the IMPORT case and call
check_caps at the appropriate point.
Signed-off-by: Sage Weil <sage@newdream.net>
Passing a session pointer to ceph_check_caps() used to mean it would leave
the session mutex locked. That wasn't always possible if it wasn't passed
CHECK_CAPS_AUTHONLY. If could unlock the passed session and lock a
differet session mutex, which was clearly wrong, and also emitted a
warning when it a racing CPU retook it and we did an unlock from the wrong
context.
This was only a problem when there was more than one MDS.
First, make ceph_check_caps unconditionally drop the session mutex, so that
it is free to lock other sessions as needed. Then adjust the one caller
that passes in a session (handle_cap_grant) accordingly.
Signed-off-by: Sage Weil <sage@newdream.net>
This causes an oops when debug output is enabled and we kick
an osd request with no current r_osd (sometime after an osd
failure). Check the pointer before dereferencing.
Signed-off-by: Sage Weil <sage@newdream.net>
Previously we would decode state directly into our current ticket_handler.
This is problematic if for some reason we fail to decode, because we end
up with half new state and half old state.
We are probably already in bad shape if we get an update we can't decode,
but we may as well be tidy anyway. Decode into new_* temporaries and
update the ticket_handler only on success.
Signed-off-by: Sage Weil <sage@newdream.net>
Commit 27943620cb introduced spurious
IRQ handling but it has a race condition where valid completion can be
lost while trying to clear spurious IRQ leading to occassional command
timeouts.
This patch improves SFF interrupt handler such that
1. Once BMDMA HSM is stopped, the condition is never considered
spurious. As there's no way to resume stopped BMDMA HSM, if device
status doesn't agree with BMDMA status, the only way out is
aborting the command (otherwise, it will just end up timing out).
2. ap->ops->sff_check_status() can be safely called to clear spurious
device IRQ as it atomically returns completion status but BMDMA IRQ
status can't be cleared in safe way if command is in flight. After
a spurious IRQ, call ap->ops->sff_irq_clear() only if the
respective device is idle and retry completion if
sff_check_status() indicates command completion.
Please note that ata_piix uses bmdma_status for sff_irq_check() and #2
won't weaken spurious IRQ handling even with in-flight command because
if bmdma_status indicates IRQ pending but device status is not on
spurious check, the next IRQ handler invocation will abort the command
due to #1.
This fixes bko#15537.
https://bugzilla.kernel.org/show_bug.cgi?id=15537
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Andrew Benton <b3nton@gmail.com>
Cc: Petr Uzel <petr.uzel@centrum.cz>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The parent rb_node needs to be initialized to shut up the compiler, even
though we're unlikely to ever hit this issue at run time.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
select_idle_routine() and register_sh_pmu() both needed their annotations
fixed up to silence section mismatch warnings.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Dominik Brodowski