Add a new command to the queue handlers: "flush",
this moves the flush() callback from mac80211
into rt2x00queue and adds support for flushing
the RX queue as well.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As part of the queue refactoring, change the queue callback
function names to have 3 different actions: start, kick & stop.
We can now also remove the STATE_RADIO_RX_ON/STATE_RADIO_RX_OFF
device_state flags, and replace the usage with using the
start_queue/stop_queue callback functions.
This streamlines the RX queue handling to the
similar approach as all other queues.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As part of the queue refactoring, we now introduce
3 queue commands: start, kick, stop.
- Start: will enable a queue, for TX this will
not mean anything, while for beacons and RX
this will update the registers to enable the queue.
- Kick: This will kick all pending frames to
the hardware. This is needed for the TX queue
to push all frames to the HW after the queue
has been started
- Stop: This will stop the queue in the hardware,
and cancel any pending work (So this doesn't
mean the queue is empty after a stop!).
Move all code from the drivers into the appropriate
functions, and link those calls to the old rt2x00lib
callback functions (we will fix this later when we
refactor the queue control inside rt2x00lib).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 0204464329 "Check for specific changed
flags when updating the erp config" changed the way in which a new beacon
interval gets handled. However, due to a bug in rt2800usb and rt2800pci the
beacon interval was reset during each scan, thus causing problems in AdHoc
mode.
Fix this by not cleaning up the beacon interval when killing the beacon queue
but just prevent the device from sending out beacons.
Reported-by: Wolfgang Kufner <wolfgang.kufner@gmail.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement the get_survey callback to allow user space to read statistics
about the current channel condition.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800usb chips need to add 1~3 bytes zero padding after each 802.11 header & payload,
and at the end need to add 4 bytes zero padding whether doing TX bulk aggregation or not,
TXINFO_W0_USB_DMA_TX_PKT_LEN in TXINFO must include 1-3 bytes padding after 802.11 header & payload
but do not include 4 bytes end zero padding.
In rt2800usb_get_tx_data_len do not consider multiple of the USB packet size case, sometimes this will
cause USB DMA problem.
Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enabling of RT30xx devices via Kconfig variables was introduced when these
devices weren't properly supported yet.
Now that that they are properly supported and functional, we can remove these
Kconfig variables for RT30xx devices and simply enable them whenever rt2800pci
and/or rt2800usb is enabled.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Modified from Eddy's patch by adding the RT3370 USB support as well.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Eddy Tsai <Eddy_Tsai@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add watchdog functions for managing the Queues inside the hardware.
Normally the driver doesn't have much to do with these queues
directly, but the Ralink drivers did implement watchdog functions
for these. These watchdog functions are not triggered that often,
compared to the other watchdog functions, but I have at least
seen them trigger once or twice during a long stresstest run.
v2: Add extra documentation for register fields
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As part of the queue refactoring, the rt2x00lib_toggle_rx
can be removed and replaced with the call directly to
the set_device_state callback function.
We can remove the STATE_RADIO_RX_ON_LINK and
STATE_RADIO_RX_OFF_LINK, as it was only used for
special behavior inside rt2x00lib rather then the
drivers.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800usb.c:48: ERROR: do not initialise statics to 0 or NULL
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Legacy driver uses 0xff as the second argument for the MCU_SLEEP
command. It is still unknown what the values actually mean, but
this will at least keep the command in-sync with the original
driver.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement a basic flush callback function, which simply loops
over all TX queues and waits until all frames have been transmitted
and the status reports have been gathered.
At this moment we don't support dropping any frames during the
flush, but mac80211 will only send 'false' for this argument anyway,
so this is not important at this time.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All rt2x00 devices used the same Tx and Rx ring size (24 entries) till
now. Newer devices (like rt2800) can however make use of a larger TX and
RX ring due to 11n capabilities (AMPDUs of size 64 for example).
Hence, bring rt2x00 in sync with the legacy drivers and use the same TX
and RX ring sizes. Also remove the global defines RX_ENTRIES, TX_ENTRIES,
BEACON_ENTRIES and ATIM_ENTRIES and use per driver values.
That is 24 entries for rt2400pci, 32 entries for rt2500pci, rt2500usb,
rt61pci and rt73usb and 128 (RX) and 64 (TX) for rt2800pci and rt2800usb.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
USB devices upload their beacon and then automatically send
it out every beacon interval. However when killing a TX queue
we only kill the URB and not the actual transmission of the beacon.
This will reset the Beacon register to prevent any beacons from
being transmitted.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add PWR_PIN_CFG initialization for rt2800usb at the same point
as rt2800pci.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Similar to rt2800_wait_wpdma_ready() we can add a
function to waiting until the CSR is ready. This
centralizes some additional code into rt2800lib.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The functions rt2800pci_enable_radio and rt2800usb_disable_radio are
almost equal and can be merged into rt2800lib. This reduces the number
of functions which must be exported from rt2800lib to the drivers at
the same time.
Also rt2800pci_disable_radio and rt2800usb_disable_radio are almost
equal and can be merged into rt2800lib in a similar fashion.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
write_tx_desc shouldn't pass a rt2x00dev and skb pointer,
instead it should use the same format as other TX frame
callback functions, which is passing the data_entry pointer
which contains all the information which is needed to work
on a TX frame.
Most callers of the kick_tx_queue and kill_tx_queue already
have the data_queue pointer, so rather then sending the QID
with the given function, when the driver requests a new
pointer to the data_queue, it is more efficient to just
send the data_queue pointer directly.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TX_STA_FIFO register which is used for per-frame TX frame
status reporting is also valid on rt2800usb. We can move the
rt2800pci_txdone function into rt2800lib where it can also
be used by rt2800usb.
rt2800usb needs to overwrite the txdone work handler to
a different function.
Both rt2800usb as rt2800_txdone need to take into account
that IO failures can occur while uploading the URB, which
means that when obtaining the new entry the IO status must
be checked.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The only reason why the write_tx_data callback function
is needed inside the driver, is because the location of
the TXWI descriptor is different on PCI and USB hardware.
Except for the beacon, where the TXWI is always at the
start of the SKB buffer.
In both cases the drivers write_tx_data function only
wrap around the function rt2800_write_txwi. Move write_tx_data
completely into the rt2800lib library, and add a callback
function to obtain the TXWI pointer.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All callback functions are gathered in rt2x00dev->ops except
for the callback functions which are used in rt2800lib to
acces rt2800pci/usb.
Move the priv pointer from rt2x00dev to rt2x00dev->ops and
rename it to drv to make it obvious that it is the driver callback
structure.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Large parts of the firmware initialization are shared
between rt2800pci and rt2800usb. Move this code into
rt2800lib.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use separate mac80211_ops for rt2800pci and rt2800usb in preparation
for further fixes. This shouldn't introduce functional changes.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use threaded interrupts for all rt2x00 PCI devices.
This has several generic advantages:
- Reduce the time we spend in hard irq context
- Use non-atmic mac80211 functions for rx/tx
Furthermore implementing broad- and multicast buffering will be
much easier in process context while maintaining low latency and
updating the beacon just before transmission (pre tbtt interrupt)
can also be done in process context.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement watchdog monitoring for USB devices (PCI support can
be added later). This will determine if URBs being uploaded to
the hardware are actually returning. Both rt2500usb and rt2800usb
have shown that URBs being uploaded can remain hanging without
being released by the hardware.
By using this watchdog, a queue can be reset when this occurs.
For rt2800usb it has been tested that the connection is preserved
even though this interruption.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename CONFIG_DISABLE_LINK_TUNING to DRIVER_SUPPORT_LINK_TUNING
Link tuning support is not only based on EEPROM decisions, but
also if the device actually supports it.
Currently only rt2500usb doesn't support link tuning because
of hardware problems. But rt2800usb is also suspected of having
problems with link tuning.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The RSSI values in the RXWI descriptor aren't true RSSI
values. Instead they are more like the AGC values similar
to rt61pci. And as such, it needs the same conversion
before it can be passed to rt2x00lib/mac80211.
This requires the struct queue_entry to be passed to
rt2800_process_rxwi rather then the skb structure which
is contained in the queue_entry. This is required to
obtain the lna_gain information from the rt2x00_dev structure.
This fixes connection problems when using wpa_supplicant
which would try to connect to the worst AP's rather then the
best ones.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Align with the way PCI devices are handled, even though it is not
strictly necessary.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that rt2x00pci_write_tx_data and rt2x00usb_write_tx_data are similar
we can merge them in a single function in rt2x00queue.c.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hardware cryptography seems to be working
on a 11G network with WPA/WPA2 cryptography
enabled. WEP still needs to be tested...
Signed-of-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Latest versions of the Ralink rt2800 family drivers use 0 as the token value,
not 0xff.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
This prevents us having common code depend on PCI or USB specific code.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
The beacon writing functions of rt2800pci and rt2800usb are now identical.
Move them to rt2800lib to only have one central function.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
There is no need to force the separation between a buffer USB vendor
request that does fit the CSR cache and one that doesn't onto the
callers. This is something that the rt2x00usb_vendor_request_buff
function can figure out by itself.
Combine the rt2x00usb_vendor_request_buff and
rt2x00usb_vendor_request_large_buff functions into a single one, as
both of them were equivalent for small buffers anyway.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
The recent changes to skb handling introduced a bug in the rt2800usb
TX descriptor writing whereby the length of the USB packet wasn't
calculated correctly.
Found via code inspection, as the devices themselves didn't seem to mind.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Instead of fiddling with the skb->data pointer and thereby risking
out of bounds accesses, properly reserve the space needed in an
skb for descriptors.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Not all the devices require a TX descriptor to be written (i.e. rt2800
device don't require them). Push down the creation of the TX descriptor
to the device drivers so that they can decide for themselves whether
a TX descriptor is to be created.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
This reverts commit 663cb47cc2.
This patch was merged out of the proper order, so instead of fixing a
problem with a prior (unmerged) patch, it creates one. Ooops!
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The recent changes to skb handling introduced a bug in the rt2800usb
TX descriptor writing whereby the length of the USB packet wasn't
calculated correctly.
Found via code inspection, as the devices themselves didn't seem to mind.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The handling of tx descriptors for beacons can be simplified by updating
write_tx_desc implementations of each driver to write directly to the
queue entry descriptor instead of to a provided memory area.
This is also a preparation for further clean ups where descriptors are
properly reserved in the skb instead of fiddling with the skb data
pointer.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
s/X/x
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to the Ralink vendor driver for rt2800 we don't need a full
TXD for a beacon but just a TXWI in front of the actual beacon.
Fix the rt2800pci and rt2800usb beaconing code accordingly.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Preparation to fix rt2800 beaconing.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All of the driver's kick_tx_queue callback functions treat the TX queue
for beacons in a special manner.
Clean this up by integrating the kicking of the beacon queue into the
write_beacon callback function, and let the generic code no longer call
the kick_tx_queue callback function when updating the beacon.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RXWI processing is exactly the same for rt2800pci and rt2800usb, so
make it common code.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TXWI writing is exactly the same for rt2800pci and rt2800usb, so
make it common code.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn