BTW, what does pat_wc_enabled stand for? Does it mean
"write-combining"?
Currently it is used to globally switch on or off PAT support.
Thus I renamed it to pat_enabled.
I think this increases readability (and hope that I didn't miss
something).
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Allows us to dump PCI space before any kernel changes have been made.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Contention for scarce PCI memory resources has been growing
due to an increasing number of PCI slots in large multi-node
systems. The kernel currently attempts by default to
allocate memory for all PCI expansion ROMs so there has
also been an increasing number of PCI memory allocation
failures seen on these systems. This occurs because the
BIOS either (1) provides insufficient PCI memory resource
for all the expansion ROMs or (2) provides adequate PCI
memory resource for expansion ROMs but provides the
space in kernel unexpected BIOS assigned P2P non-prefetch
windows.
The resulting PCI memory allocation failures may be benign
when related to memory requests for expansion ROMs themselves
but in some cases they can occur when attempting to allocate
space for more critical BARs. This can happen when a successful
expansion ROM allocation request consumes memory resource
that was intended for a non-ROM BAR. We have seen this
happen during PCI hotplug of an adapter that contains a
P2P bridge where successful memory allocation for an
expansion ROM BAR on device behind the bridge consumed
memory that was intended for a non-ROM BAR on the P2P bridge.
In all cases the allocation failure messages can be very
confusing for users.
This patch provides a new 'pci=norom' kernel boot parameter
that can be used to disable the default PCI expansion ROM memory
resource allocation. This provides a way to avoid the above
described issues on systems that do not contain PCI devices
for which drivers or user-level applications depend on the
default PCI expansion ROM memory resource allocation behavior.
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
... so it could fall back to normal numa and we'd reduce the impact of the
NUMAQ subarch.
NUMAQ depends on GENERICARCH
also decouple genericarch numa from acpi.
also make it fall back to bigsmp if apicid > 8.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This BIOS claims the VIA 8237 south bridge to be compatible with VIA 586,
which it is not.
Without this patch, I get the following warning while booting,
among others,
| PCI: Using IRQ router VIA [1106/3227] at 0000:00:11.0
| ------------[ cut here ]------------
| WARNING: at arch/x86/pci/irq.c:265 pirq_via586_get+0x4a/0x60()
| Modules linked in:
| Pid: 1, comm: swapper Not tainted 2.6.26-rc4-00015-g1ec7d99 #1
| [<c0119fd4>] warn_on_slowpath+0x54/0x70
| [<c02246e0>] ? vt_console_print+0x210/0x2b0
| [<c02244d0>] ? vt_console_print+0x0/0x2b0
| [<c011a413>] ? __call_console_drivers+0x43/0x60
| [<c011a482>] ? _call_console_drivers+0x52/0x80
| [<c011aa89>] ? release_console_sem+0x1c9/0x200
| [<c0291d21>] ? raw_pci_read+0x41/0x70
| [<c0291e8f>] ? pci_read+0x2f/0x40
| [<c029151a>] pirq_via586_get+0x4a/0x60
| [<c02914d0>] ? pirq_via586_get+0x0/0x60
| [<c029178d>] pcibios_lookup_irq+0x15d/0x430
| [<c03b895a>] pcibios_irq_init+0x17a/0x3e0
| [<c03a66f0>] ? kernel_init+0x0/0x250
| [<c03a6763>] kernel_init+0x73/0x250
| [<c03b87e0>] ? pcibios_irq_init+0x0/0x3e0
| [<c0114d00>] ? schedule_tail+0x10/0x40
| [<c0102dee>] ? ret_from_fork+0x6/0x1c
| [<c03a66f0>] ? kernel_init+0x0/0x250
| [<c03a66f0>] ? kernel_init+0x0/0x250
| [<c010324b>] kernel_thread_helper+0x7/0x1c
| =======================
| ---[ end trace 4eaa2a86a8e2da22 ]---
and IRQ trouble later,
| irq 10: nobody cared (try booting with the "irqpoll" option)
Now that's an VIA 8237 chip, so pirq_via586_get shouldn't be called
at all; adding this workaround to via_router_probe() fixes the
problem for me.
Amazingly I have a 2.6.23.8 kernel that somehow works fine ... I'll
never understand why.
Signed-off-by: Bertram Felgenhauer <int-e@gmx.de>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Previously, one would have to specifically choose CONFIG_OLPC and
CONFIG_PCI_GOOLPC in order to enable PCI_OLPC. That doesn't really work
for distro kernels, so this patch allows one to choose CONFIG_OLPC and
CONFIG_PCI_GOANY in order to build in OLPC support in a generic kernel (as
requested by Robert Millan).
This also moves GOOLPC before GOANY in the menuconfig list.
Finally, make pci_access_init return early if we detect OLPC hardware.
There's no need to continue probing stuff, and pci_pcbios_init
specifically trashes our settings (we didn't run into that before because
PCI_GOANY wasn't supported).
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch implements PCI extended configuration space access for
AMD's Barcelona CPUs. It extends the method using CF8/CFC IO
addresses. An x86 capability bit has been introduced that is set for
CPUs supporting PCI extended config space accesses.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This BIOS claims the VIA 8237 south bridge to be compatible with VIA 586,
which it is not.
Without this patch, I get the following warning while booting,
among others,
| PCI: Using IRQ router VIA [1106/3227] at 0000:00:11.0
| ------------[ cut here ]------------
| WARNING: at arch/x86/pci/irq.c:265 pirq_via586_get+0x4a/0x60()
| Modules linked in:
| Pid: 1, comm: swapper Not tainted 2.6.26-rc4-00015-g1ec7d99 #1
| [<c0119fd4>] warn_on_slowpath+0x54/0x70
| [<c02246e0>] ? vt_console_print+0x210/0x2b0
| [<c02244d0>] ? vt_console_print+0x0/0x2b0
| [<c011a413>] ? __call_console_drivers+0x43/0x60
| [<c011a482>] ? _call_console_drivers+0x52/0x80
| [<c011aa89>] ? release_console_sem+0x1c9/0x200
| [<c0291d21>] ? raw_pci_read+0x41/0x70
| [<c0291e8f>] ? pci_read+0x2f/0x40
| [<c029151a>] pirq_via586_get+0x4a/0x60
| [<c02914d0>] ? pirq_via586_get+0x0/0x60
| [<c029178d>] pcibios_lookup_irq+0x15d/0x430
| [<c03b895a>] pcibios_irq_init+0x17a/0x3e0
| [<c03a66f0>] ? kernel_init+0x0/0x250
| [<c03a6763>] kernel_init+0x73/0x250
| [<c03b87e0>] ? pcibios_irq_init+0x0/0x3e0
| [<c0114d00>] ? schedule_tail+0x10/0x40
| [<c0102dee>] ? ret_from_fork+0x6/0x1c
| [<c03a66f0>] ? kernel_init+0x0/0x250
| [<c03a66f0>] ? kernel_init+0x0/0x250
| [<c010324b>] kernel_thread_helper+0x7/0x1c
| =======================
| ---[ end trace 4eaa2a86a8e2da22 ]---
and IRQ trouble later,
| irq 10: nobody cared (try booting with the "irqpoll" option)
Now that's an VIA 8237 chip, so pirq_via586_get shouldn't be called
at all; adding this workaround to via_router_probe() fixes the
problem for me.
Amazingly I have a 2.6.23.8 kernel that somehow works fine ... I'll
never understand why.
Signed-off-by: Bertram Felgenhauer <int-e@gmx.de>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
there is a typo in the mask value, need to remove that extra 0,
to avoid 4bit clearing.
Signed-off-by: Yinghal Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Greetings.
There is a code flaw in the bfsort whitelist, where there are redundant
entries for the same two HP systems, DL385 G2 and DL585 G2. This patch
replaces those redundant entries with the correct ones. The correct
entries are for large-volume systems, the DL360 and DL380.
-----------------------------------------------------------------------
commit ec69f0374c3b0ad7ea991b0e9ac00377acfe5b1a
Author: Tony Camuso <tony.camuso@hp.com>
Date: Wed May 14 07:09:28 2008 -0400
Replace Redundant Whitelist Entries with the Correct Ones
The ProLiant DL585 G2 and the DL585 G2 are entered reundantly
in the dmi_system_id table. What should have been there are the
DL360 and DL380. This patch simply replaces the redundant
entries with the correct entries.
arch/x86/pci/common.c | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
Signed-off-by: Tony Camuso <tony.camuso@hp.com>
Signed-off-by: Pat Schoeller <patrick.schoeller@hp.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Replace Redundant Whitelist Entries with the Correct Ones
The ProLiant DL585 G2 and the DL585 G2 are entered reundantly in the
dmi_system_id table. What should have been there are the DL360 and DL380. This
patch simply replaces the redundant entries with the correct entries.
Signed-off-by: Tony Camuso <tony.camuso@hp.com>
Signed-off-by: Pat Schoeller <patrick.schoeller@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Some versions of X used the mprotect workaround to change caching type from UC
to WB, so that it can then use mtrr to program WC for that region [1]. Change
the mmap of pci space through /sys or /proc interfaces from UC to UC_MINUS.
With this change, X will not need to use mprotect workaround to get WC type
since the MTRR mapping type will be honored.
The bug in mprotect that clobbers PAT bits is fixed in a follow on patch. So,
this X workaround will stop working as well.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86:
x86: rdc: leds build/config fix
x86: sysfs cpu?/topology is empty in 2.6.25 (32-bit Intel system)
x86: revert commit 709f744 ("x86: bitops asm constraint fixes")
x86: restrict keyboard io ports reservation to make ipmi driver work
x86: fix fpu restore from sig return
x86: remove spew print out about bus to node mapping
x86: revert printk format warning change which is for linux-next
x86: cleanup PAT cpu validation
x86: geode: define geode_has_vsa2() even if CONFIG_MGEODE_LX is not set
x86: GEODE: cache results from geode_has_vsa2() and uninline
x86: revert geode config dependency
Jeff Garzik pointed out that this printout is not needed.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This reverts commit 9f8daccaa0, which was
reported to break X startup (xf86-video-ati-6.8.0). See
http://bugs.freedesktop.org/show_bug.cgi?id=15523
for details.
Reported-by: Laurence Withers <l@lwithers.me.uk>
Cc: Gary Hade <garyhade@us.ibm.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: "Jun'ichi Nomura" <j-nomura@ce.jp.nec.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
x86 PCI: call dmi_check_pciprobe()
x86/pci: add pci=skip_isa_align command lines.
x86/pci: remove flag in pci_cfg_space_size_ext
x86: fix section mismatch in pci_scan_bus
this change:
| commit 08f1c192c3
| Author: Muli Ben-Yehuda <muli@il.ibm.com>
| Date: Sun Jul 22 00:23:39 2007 +0300
|
| x86-64: introduce struct pci_sysdata to facilitate sharing of ->sysdata
|
| This patch introduces struct pci_sysdata to x86 and x86-64, and
| converts the existing two users (NUMA, Calgary) to use it.
|
| This lays the groundwork for having other users of sysdata, such as
| the PCI domains work.
|
| The Calgary bits are tested, the NUMA bits just look ok.
replaces pcibios_scan_root with pci_scan_bus_parented...
but in pcibios_scan_root we have a DMI check:
dmi_check_system(pciprobe_dmi_table);
when when have several peer root buses this could be called multiple
times (which is bad), so move that call to pci_access_init().
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
so we don't align the io port start address for pci cards.
also move out dmi check out acpi.c, because it has nothing to do with acpi.
it could spare some calling when we have several peer root buses.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
arch/x86/pci/Makefile_32 has a nasty detail. VISWS and NUMAQ build
override the generic pci-y rules. This needs a proper cleanup, but
that needs more thoughts. Undo
commit 895d30935e
x86: numaq fix
do not override the existing pci-y rule when adding visws or
numaq rules.
There is also a stupid init function ordering problem vs. acpi.o
Add comments to the Makefile to avoid tripping over this again.
Remove the srat stub code in discontig_32.c to allow a proper NUMAQ
build.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use UC_MINUS for ioremap(), ioremap_nocache() instead of strong UC.
Once all the X drivers move to ioremap_wc(), we can go back to strong
UC semantics for ioremap() and ioremap_nocache().
To avoid attribute aliasing issues, pci_mmap_page_range() will also
use UC_MINUS for default non write-combining mapping request.
Next steps:
a) change all the video drivers using ioremap() or ioremap_nocache()
and adding WC MTTR using mttr_add() to ioremap_wc()
b) for strict usage, we can go back to strong uc semantics
for ioremap() and ioremap_nocache() after some grace period for
completing step-a.
c) user level X server needs to use the appropriate method for setting
up WC mapping (like using resourceX_wc sysfs file instead of
adding MTRR for WC and using /dev/mem or resourceX under /sys)
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
so let pci_cfg_space_size call it directly without flag.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix following section mismatch warning:
WARNING: vmlinux.o(.text+0x275616): Section mismatch in reference from the function pci_scan_bus() to the function .devinit.text:pci_scan_bus_parented()
The warning was seen with a CONFIG_DEBUG_SECTION_MISMATCH=y build.
The inline function pci_scan_bus refer to functions annotated
__devinit - so annotate it __devinit too.
This revealed a few x86 specific functions that were only
used from __init or __devinit context.
So annotate these __devinit and the warning was killed.
The added include in pci.h was not strictly required but
added to avoid being dependent on indirect includes.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Jesse Barnes <jbarnes@hobbes.lan>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86-bigbox-pci:
x86: add pci=check_enable_amd_mmconf and dmi check
x86: work around io allocation overlap of HT links
acpi: get boot_cpu_id as early for k8_scan_nodes
x86_64: don't need set default res if only have one root bus
x86: double check the multi root bus with fam10h mmconf
x86: multi pci root bus with different io resource range, on 64-bit
x86: use bus conf in NB conf fun1 to get bus range on, on 64-bit
x86: get mp_bus_to_node early
x86 pci: remove checking type for mmconfig probe
x86: remove unneeded check in mmconf reject
driver core: try parent numa_node at first before using default
x86: seperate mmconf for fam10h out from setup_64.c
x86: if acpi=off, force setting the mmconf for fam10h
x86_64: check MSR to get MMCONFIG for AMD Family 10h
x86_64: check and enable MMCONFIG for AMD Family 10h
x86_64: set cfg_size for AMD Family 10h in case MMCONFIG
x86: mmconf enable mcfg early
x86: clear pci_mmcfg_virt when mmcfg get rejected
x86: validate against acpi motherboard resources
Fixed up fairly trivial conflicts in arch/x86/pci/{init.c,pci.h} due to
OLPC support manually.
This adds support for OLPC XO hardware. Open Firmware on XOs don't contain
the VSA, so it is necessary to emulate the PCI BARs in the kernel. This also
adds functionality for running EC commands, and a CONFIG_OLPC.
A number of OLPC drivers depend upon CONFIG_OLPC.
olpc_ec_timeout is a hack to work around Embedded Controller bugs.
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: geode_has_vsa build fix]
[akpm@linux-foundation.org: olpc_register_battery_callback doesn't exist]
Signed-off-by: Andres Salomon <dilinger@debian.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
so will disable that feature by default, and only enable that via
pci=check_enable_amd_mmconf or for system match with dmi table.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
normally BIOSes assign io/mmio range to different HT links without
overlapping, even same node same link should get non overlapping
entries.
but Rafael L. Wysocki's buggy BIOS creates a link with overlapping
entries for mmio and io:
node 0 link 0: io port [1000, ffffff]
node 0 link 0: mmio [e0000000, efffffff]
node 0 link 0: mmio [a0000, bffff]
node 0 link 0: mmio [80000000, ffffffff]
try to merge them and we will get:
bus: [00, ff] on node 0 link 0
bus: 00 index 0 io port: [0, ffff]
bus: 00 index 1 mmio: [80000000, fcffffffff]
bus: 00 index 2 mmio: [a0000, bffff]
so later we will reduce the chance to assign used resource to
unassigned device.
Reported-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Tested-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
if there's only one root bus there's no need to split resources.
This patch fixes the issue described at:
http://lkml.org/lkml/2008/4/10/304
Reported-and-bisected-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
some bioses give same range to mmconf for fam10h msr, and mmio for node/link.
fam10h msr will overide mmio for node/link.
so we can not assign range to devices under node/link for unassigned resources.
this patch will take range out from the mmio for node/link
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
scan AMD opteron io/mmio routing to make sure every pci root bus get correct
resource range. Thus later pci scan could assign correct resource to device
with unassigned resource.
this can fix a system without _CRS for multi pci root bus.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
... so we use the same code with Quad core cpu as old opteron.
This patch is useful when acpi=off or _PXM is not there in DSDT.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Currently, on an amd k8 system with multi ht chains, the numa_node of
pci devices under /sys/devices/pci0000:80/* is always 0, even if that
chain is on node 1 or 2 or 3.
Workaround: pcibus_to_node(bus) is used when we want to get the node that
pci_device is on.
In struct device, we already have numa_node member, and we could use
dev_to_node()/set_dev_node() to get and set numa_node in the device.
set_dev_node is called in pci_device_add() with pcibus_to_node(bus),
and pcibus_to_node uses bus->sysdata for nodeid.
The problem is when pci_add_device is called, bus->sysdata is not assigned
correct nodeid yet. The result is that numa_node will always be 0.
pcibios_scan_root and pci_scan_root could take sysdata. So we need to get
mp_bus_to_node mapping before these two are called, and thus
get_mp_bus_to_node could get correct node for sysdata in root bus.
In scanning of the root bus, all child busses will take parent bus sysdata.
So all pci_device->dev.numa_node will be assigned correctly and automatically.
Later we could use dev_to_node(&pci_dev->dev) to get numa_node, and we
could also could make other bus specific device get the correct numa_node
too.
This is an updated version of pci_sysdata and Jeff's pci_domain patch.
[ mingo@elte.hu: build fix ]
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
doesn't need to check if it is type1 or type2, we can use raw_pci_ops
directly.
also make pci_direct_conf1 static again.
anyway is there system with type 2 and mmconf support?
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
mmconfig is only used to access extended configuration space.
so don't need to reject MFG that only have one entry and only handle bus0.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
so even booting kernel with acpi=off or even MCFG is not there, we still can
use MMCONFIG.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Greg KH <greg@kroah.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
reuse pci_cfg_space_size but skip check pci express and pci-x CAP ID.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Patch
"x86: validate against ACPI motherboard resources"
changed the mmconf init sequence, and init MMCONF late in acpi_init.
here change it back to old sequence:
1. check hostbridge in early
2. check MCFG with e820 in early
3. if all fail, will check MCFg with acpi _CRS in acpi_init
So we can make MCONF working again when acpi=off is set if hostbridge
support that.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: Greg KH <greg@kroah.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
For x86_64, need to free pci_mmcfg_virt, and iounmap some pointers
when MMCONF is not reserved in E820 or acpi _CRS and get rejected.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: Greg KH <greg@kroah.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This path adds validation of the MMCONFIG table against the ACPI reserved
motherboard resources. If the MMCONFIG table is found to be reserved in
ACPI, we don't bother checking the E820 table. The PCI Express firmware
spec apparently tells BIOS developers that reservation in ACPI is required
and E820 reservation is optional, so checking against ACPI first makes
sense. Many BIOSes don't reserve the MMCONFIG region in E820 even though
it is perfectly functional, the existing check needlessly disables MMCONFIG
in these cases.
In order to do this, MMCONFIG setup has been split into two phases. If PCI
configuration type 1 is not available then MMCONFIG is enabled early as
before. Otherwise, it is enabled later after the ACPI interpreter is
enabled, since we need to be able to execute control methods in order to
check the ACPI reserved resources. Presently this is just triggered off
the end of ACPI interpreter initialization.
There are a few other behavioral changes here:
- Validate all MMCONFIG configurations provided, not just the first one.
- Validate the entire required length of each configuration according to
the provided ending bus number is reserved, not just the minimum required
allocation.
- Validate that the area is reserved even if we read it from the chipset
directly and not from the MCFG table. This catches the case where the
BIOS didn't set the location properly in the chipset and has mapped it
over other things it shouldn't have.
This also cleans up the MMCONFIG initialization functions so that they
simply do nothing if MMCONFIG is not compiled in.
Based on an original patch by Rajesh Shah from Intel.
[akpm@linux-foundation.org: many fixes and cleanups]
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Andi Kleen <ak@suse.de>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andi Kleen <ak@suse.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use the generic pci_enable_resources() instead of the arch-specific code.
Unlike this arch-specific code, the generic version:
- checks for resource collisions with "!r->parent"
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The "pci=routeirq" option was added in 2004, and I don't get any valid
reports anymore. The option is still mentioned in kernel-parameters.txt.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The PCI bus names included in /proc/iomem and /proc/ioports are
of the form 'PCI Bus #XX' where XX is the bus number. This patch
changes the naming to 'PCI Bus XXXX:YY' where XXXX is the domain
number and YY is the bus number. For example, PCI bus 14 in
domain 0 will show as 'PCI Bus 0000:14' instead of 'PCI Bus #14'.
This change makes the naming consistent with other architectures
such as ia64 where multiple PCI domain support has been around
longer.
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This function was obviously never being used since early 2.5 days as any
device that it would try to remove would never really be removed from
the system due to the PCI device list being held in the driver core, not
the general list of PCI devices.
As we have not had a single report of a problem here in 4 years, I think
it's safe to remove now.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We currently keep 2 lists of PCI devices in the system, one in the
driver core, and one all on its own. This second list is sorted at boot
time, in "BIOS" order, to try to remain compatible with older kernels
(2.2 and earlier days). There was also a "nosort" option to turn this
sorting off, to remain compatible with even older kernel versions, but
that just ends up being what we have been doing from 2.5 days...
Unfortunately, the second list of devices is not really ever used to
determine the probing order of PCI devices or drivers[1]. That is done
using the driver core list instead. This change happened back in the
early 2.5 days.
Relying on BIOS ording for the binding of drivers to specific device
names is problematic for many reasons, and userspace tools like udev
exist to properly name devices in a persistant manner if that is needed,
no reliance on the BIOS is needed.
Matt Domsch and others at Dell noticed this back in 2006, and added a
boot option to sort the PCI device lists (both of them) in a
breadth-first manner to help remain compatible with the 2.4 order, if
needed for any reason. This option is not going away, as some systems
rely on them.
This patch removes the sorting of the internal PCI device list in "BIOS"
mode, as it's not needed at all anymore, and hasn't for many years.
I've also removed the PCI flags for this from some other arches that for
some reason defined them, but never used them.
This should not change the ordering of any drivers or device probing.
[1] The old-style pci_get_device and pci_find_device() still used this
sorting order, but there are very few drivers that use these functions,
as they are deprecated for use in this manner. If for some reason, a
driver rely on the order and uses these functions, the breadth-first
boot option will resolve any problem.
Cc: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Bug fixes for reserve_memtype() call in __ioremap and pci_mmap_page_range().
If reserve_memtype returns non-zero, then it is an error and subsequent free is
not required. Requested and returned prot value check should be done when
reserve_memtype returns success.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add reserve_memtype and free_memtype wrapper for pci_mmap_page_range. Free
is called on unmap, but identity map continues to be mapped as per
pci_mmap_page_range request, until next request for the same region calls
ioremap_change_attr(), which will go through without conflict. This way of
mapping is identical to one used in ioremap/iounmap.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove the last leftovers from the files. Move the ones
that are still used to the files they belong, the others
that grep can't reach, simply throw away.
Merge comments ontop of file and that's it: smpboot integrated
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
http://bugzilla.kernel.org/show_bug.cgi?id=10124
this change:
commit 08f1c192c3
Author: Muli Ben-Yehuda <muli@il.ibm.com>
Date: Sun Jul 22 00:23:39 2007 +0300
x86-64: introduce struct pci_sysdata to facilitate sharing of ->sysdata
This patch introduces struct pci_sysdata to x86 and x86-64, and
converts the existing two users (NUMA, Calgary) to use it.
This lays the groundwork for having other users of sysdata, such as
the PCI domains work.
The Calgary bits are tested, the NUMA bits just look ok.
replaces pcibios_scan_root by pci_scan_bus_parented...
but in pcibios_scan_root we have a check about scanned busses.
Cc: <yakui.zhao@intel.com>
Cc: Stian Jordet <stian@jordet.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "Yinghai Lu" <yhlu.kernel@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I figured out another ACPI related regression today.
randconfig testing triggered an early boot-time hang on a laptop of mine
(32-bit x86, config attached) - the screen was scrolling ACPI AML
exceptions [with no serial port and no early debugging available].
v2.6.24 works fine on that laptop with the same .config, so after a few
hours of bisection (had to restart it 3 times - other regressions
interacted), it honed in on this commit:
| 10270d4838 is first bad commit
|
| Author: Linus Torvalds <torvalds@woody.linux-foundation.org>
| Date: Wed Feb 13 09:56:14 2008 -0800
|
| acpi: fix acpi_os_read_pci_configuration() misuse of raw_pci_read()
reverting this commit ontop of -rc5 gave a correctly booting kernel.
But this commit fixes a real bug so the real question is, why did it
break the bootup?
After quite some head-scratching, the following change stood out:
- pci_id->bus = tu8;
+ pci_id->bus = val;
pci_id->bus is defined as u16:
struct acpi_pci_id {
u16 segment;
u16 bus;
...
and 'tu8' changed from u8 to u32. So previously we'd unconditionally
mask the return value of acpi_os_read_pci_configuration()
(raw_pci_read()) to 8 bits, but now we just trust whatever comes back
from the PCI access routines and only crop it to 16 bits.
But if the high 8 bits of that result contains any noise then we'll
write that into ACPI's PCI ID descriptor and confuse the heck out of the
rest of ACPI.
So lets check the PCI-BIOS code on that theory. We have this codepath
for 8-bit accesses (arch/x86/pci/pcbios.c:pci_bios_read()):
switch (len) {
case 1:
__asm__("lcall *(%%esi); cld\n\t"
"jc 1f\n\t"
"xor %%ah, %%ah\n"
"1:"
: "=c" (*value),
"=a" (result)
: "1" (PCIBIOS_READ_CONFIG_BYTE),
"b" (bx),
"D" ((long)reg),
"S" (&pci_indirect));
Aha! The "=a" output constraint puts the full 32 bits of EAX into
*value. But if the BIOS's routines set any of the high bits to nonzero,
we'll return a value with more set in it than intended.
The other, more common PCI access methods (v1 and v2 PCI reads) clear
out the high bits already, for example pci_conf1_read() does:
switch (len) {
case 1:
*value = inb(0xCFC + (reg & 3));
which explicitly converts the return byte up to 32 bits and zero-extends
it.
So zero-extending the result in the PCI-BIOS read routine fixes the
regression on my laptop. ( It might fix some other long-standing issues
we had with PCI-BIOS during the past decade ... ) Both 8-bit and 16-bit
accesses were buggy.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We want to allow different implementations of pci_raw_ops for standard
and extended config space on x86. Rather than clutter generic code with
knowledge of this, we make pci_raw_ops private to x86 and use it to
implement the new raw interface -- raw_pci_read() and raw_pci_write().
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thanks to Loic Prylli <loic@myri.com>, who originally proposed
this idea.
Always using legacy configuration mechanism for the legacy config space
and extended mechanism (mmconf) for the extended config space is
a simple and very logical approach. It's supposed to resolve all
known mmconf problems. It still allows per-device quirks (tweaking
dev->cfg_size). It also allows to get rid of mmconf fallback code.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds support for flushing the chipsets on the 915, 945, 965 and G33
families of Intel chips.
The BIOS doesn't seem to always allocate the BAR on the 965 chipsets
so I have to use pci resource code to create a resource
It adds an export for pcibios_align_resource.
numa.c is the only user of the {in,out}*_quad functions. And it has only a few call
sites. Change them to open code the magic NUMAQ port access.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
I can find no reason for the _p on the serverworks IRQ routing logic, and
a review of the documentation contains no indication that any such delay
is needed so lets try this
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
we use a few static mapping rules in our pirq routing functions,
and for example regression f3ac84324f was due to the pirq
being out of range of the remapping array. Put in a few
WARN_ON_ONCE() lines so that we get notified about any such
out-of-bound incidents.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
increasing number of PCI slots in large multi-node systems. The kernel
currently attempts by default to allocate memory for all PCI expansion
ROMs so there has also been an increasing number of PCI memory
allocation failures seen on these systems. This occurs because the BIOS
either (1) provides insufficient PCI memory resource for all the
expansion ROMs or (2) provides adequate PCI memory resource for
expansion ROMs but provides the space in kernel unexpected BIOS assigned
P2P non-prefetch windows.
The resulting PCI memory allocation failures may be benign when related
to memory requests for expansion ROMs themselves but in some cases they
can occur when attempting to allocate space for more critical BARs.
This can happen when a successful expansion ROM allocation request
consumes memory resource that was intended for a non-ROM BAR. We have
seen this happen during PCI hotplug of an adapter that contains a P2P
bridge where successful memory allocation for an expansion ROM BAR on
device behind the bridge consumed memory that was intended for a non-ROM
BAR on the P2P bridge. In all cases the allocation failure messages can
be very confusing for users.
This patch addresses the issue by changing the kernel default behavior
so that expansion ROM memory allocations are no longer attempted by
default when the BIOS has not assigned a specific address range to the
expansion ROM BAR. This was done by changing the 'pci=rom' boot option
behavior for BIOS unassigned expansion ROMs to actually match it's
current kernel-parameters.txt description which already implies "off" by
default. Behavior for BIOS assigned expansion ROMs implemented in
pcibios_assign_resources() [arch/x86/pci/i386.c] is unchanged.
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jan Beulich <jbeulich@novell.com>
Acked-by: "Jun'ichi Nomura" <j-nomura@ce.jp.nec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86:
x86: fix APIC related bootup crash on Athlon XP CPUs
time: add ADJ_OFFSET_SS_READ
x86: export the symbol empty_zero_page on the 32-bit x86 architecture
x86: fix kprobes_64.c inlining borkage
pci: use pci=bfsort for HP DL385 G2, DL585 G2
x86: correctly set UTS_MACHINE for "make ARCH=x86"
lockdep: annotate do_debug() trap handler
x86: turn off iommu merge by default
x86: fix ACPI compile for LOCAL_APIC=n
x86: printk kernel version in WARN_ON and other dump_stack users
ACPI: Set max_cstate to 1 for early Opterons.
x86: fix NMI watchdog & 'stopped time' problem
HP ProLiant systems DL385 G2 and DL585 G2 need pci=bfsort to enumerate PCI
devices in the expected order.
Matt sayeth:
biosdevname is a userspace app I wrote to help solve this so we don't need
to patch the kernel for future systems. It's not integrated into any
distributions properly yet, but is included in openSUSE 10.3 and Fedora 8
for people who want to download and install it there. It acts as a udev
helper.
For the time being, patching the kernel is necessary. I really hope
biosdevname eliminates that need in future distributions.
http://linux.dell.com/biosdevname/
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Andy Gospodarek <andy@greyhouse.net>
Cc: mingo@elte.hu
Cc: andy@greyhouse.net
Cc: john.cagle@hp.com
Cc: Matt Domsch <Matt_Domsch@dell.com>
Cc: Greg KH <greg@kroah.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
need to check info->res_num less than PCI_BUS_NUM_RESOURCES, so
info->bus->resource[info->res_num] = res will not beyond of bus resource
array when acpi returns too many resource entries.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Gary Hade <gary.hade@us.ibm.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch fixes the following section mismatches with CONFIG_HOTPLUG=n:
<-- snip -->
...
WARNING: vmlinux.o(.data+0x23640): Section mismatch: reference to .init.text.20:can_skip_ioresource_align (between 'acpi_pciprobe_dmi_table' and 'pcibios_irq_mask')
WARNING: vmlinux.o(.data+0x2366c): Section mismatch: reference to .init.text.20:can_skip_ioresource_align (between 'acpi_pciprobe_dmi_table' and 'pcibios_irq_mask')
WARNING: vmlinux.o(.data+0x23698): Section mismatch: reference to .init.text.20:can_skip_ioresource_align (between 'acpi_pciprobe_dmi_table' and 'pcibios_irq_mask')
...
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Len Brown <len.brown@intel.com>
HP ProLiant systems DL385 G2 and DL585 G2 need pci=bfsort to enumerate PCI
devices in the expected order.
Matt sayeth:
biosdevname is a userspace app I wrote to help solve this so we don't need
to patch the kernel for future systems. It's not integrated into any
distributions properly yet, but is included in openSUSE 10.3 and Fedora 8
for people who want to download and install it there. It acts as a udev
helper.
For the time being, patching the kernel is necessary. I really hope
biosdevname eliminates that need in future distributions.
http://linux.dell.com/biosdevname/
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Cc: <john.cagle@hp.com>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Greg KH <greg@kroah.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix DMI const-ification fallout that appeared when merging subsystem
trees.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* fix bug in pci_read() and pci_write() which prevented PCI domain
support from working (hardcoded domain 0).
* unconditionally enable CONFIG_PCI_DOMAINS
* implement pci_domain_nr() and pci_proc_domain(), as required of
all arches when CONFIG_PCI_DOMAINS is enabled.
* store domain in struct pci_sysdata, as assigned by ACPI
* support "pci=nodomains"
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Modify PCI Bridge Control ISA flag for clarity
This patch changes PCI_BRIDGE_CTL_NO_ISA to PCI_BRIDGE_CTL_ISA
and modifies it's clarifying comment and locations where used.
The change reduces the chance of future confusion since it makes
the set/unset meaning of the bit the same in both the bridge
control register and bridge_ctl field of the pci_bus struct.
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Acked-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use _CRS for PCI resource allocation
This patch resolves an issue where incorrect PCI memory and i/o ranges
are being assigned to hotplugged PCI devices on some IBM systems. The
resource mis-allocation not only makes the PCI device unuseable but
often makes the entire system unuseable due to resulting machine checks.
The hotplug capable PCI slots on the affected systems are not located
under a standard P2P bridge but are instead located under PCI root
bridges or subtractive decode P2P bridges. For example, the IBM x3850
contains 2 hotplug capable PCI-X slots and 4 hotplug capable PCIe slots
with the PCI-X slots each located under a PCI root bridge and the PCIe
slots each located under a subtractive decode P2P bridge.
The current i386/x86_64 PCI resource allocation code does not use _CRS
returned resource information. No other resource information source is
available for slots that are not below a standard P2P bridge so
incorrect ranges are being allocated from e820 hole causing the bad
result.
This patch causes the kernel to use _CRS returned resource info. It is
roughly based on a change provided by Matthew Wilcox for the ia64 kernel
in 2005. Due to possible buggy BIOS factor and possible yet to be
discovered kernel issues the function is disabled by default and can be
enabled with pci=use_crs.
Signed-off-by: Gary Hade <gary.hade@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Skip ISA ioresource alignment on some systems
To conserve limited PCI i/o resource on some IBM multi-node systems, the
BIOS allocates (via _CRS) and expects the kernel to use addresses in
ranges currently excluded by pcibios_align_resource() [i386/pci/i386.c].
This change allows the kernel to use the currently excluded address
ranges on the IBM x3800, x3850, and x3950.
Signed-off-by: Gary Hade <gary.hade@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Force PCI bus renumbering for Compaq EVO N800c laptop, in order to get
the cardbus slot recognised.
Signed-off-by: Juha Laiho <Juha.Laiho@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On the "MSI K8T Neo2-FIR" board the BIOS disables the onboard
soundcard, if a second PCI soundcard is present.
This patch sets the korrect register bit to enable the onboard sound.
Removed old code in /drivers/pci/quirks.c that only checks for the
PCI-ID and fires on any Board with VIA 8237.
New code in /arch/i386/pci/fixup.c checks the DMI-tables and only runs
on the specific board.
Signed-off-by: Johannes Goecke <goecke@upb.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for PicoPower PT86C523 IRQ router to be used with the in-kernel
yenta driver for CardBus. With this patch cardbus works on e.g. Dell
Latitude XPi P150CD.
Initial patch for kernel 2.4 series by Sune Mølgaard
http://molgaard.org/code/linux-2.4.31-picopower.patch
Ported to 2.6.20 by Chmouel Boudjnah (http://www.chmouel.com)
Testing and confirmation that it works by Austin Acton
Cleaned up a little for inclusion in a 2.6.21-rc7 based kernel.
Added some more cleanups according to CodingStyle, as noted by
Randy Dunlap on LKML.
[akpm@linux-foundation.org: build fixes]
Signed-off-by: Thomas Backlund <tmb@mandriva.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ingo Molnar