When a Book3S HV KVM guest is running, we need the host to be in
single-thread mode, that is, all of the cores (or at least all of
the cores where the KVM guest could run) to be running only one
active hardware thread. This is because of the hardware restriction
in POWER processors that all of the hardware threads in the core
must be in the same logical partition. Complying with this restriction
is much easier if, from the host kernel's point of view, only one
hardware thread is active.
This adds two hooks in the SMP hotplug code to allow the KVM code to
make sure that secondary threads (i.e. hardware threads other than
thread 0) cannot come online while any KVM guest exists. The KVM
code still has to check that any core where it runs a guest has the
secondary threads offline, but having done that check it can now be
sure that they will not come online while the guest is running.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Add support to disable and re-enable individual cores at runtime on
MPC85xx/QorIQ SMP machines. Currently support e500v1/e500v2 core.
MPC85xx machines use ePAPR spin-table in boot page for CPU kick-off. This
patch uses the boot page from bootloader to boot core at runtime. It
supports 32-bit and 36-bit physical address.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In the case of cpu hotplug, the cpu_state should be set to CPU_UP_PREPARE
when kicking cpu. Otherwise, the cpu_state is always CPU_DEAD after
calling generic_set_cpu_dead(), which makes the delay in generic_cpu_die()
not happen.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds more generic support for doing CPU hotplug with a simple
idle loop and no actual reset of the processors. The generic
smp_generic_kick_cpu() does the hotplug bringup trick if the PACA
shows that the CPU has already been started at boot and we provide
an accessor for the CPU state.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
smp_release_cpus() waits for all cpus (including the bootcpu) due to an
off-by-one count on boot_cpu_count (which is all CPUs). This patch replaces
that with spinning_secondaries (which is all secondary CPUs).
Signed-off-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The cell iic interrupt controller has enough software caused interrupts
to use a unique interrupt for each of the 4 messages powerpc uses.
This means each interrupt gets its own irq action/data combination.
Use the seperate, optimized, arch common ipi action functions
registered via the helper smp_request_message_ipi instead passing the
message as action data to a single action that then demultipexes to
the required acton via a switch statement.
smp_request_message_ipi will register the action as IRQF_PER_CPU
and IRQF_DISABLED, and WARN if the allocation fails for some reason,
so no need to print on that failure. It will return positive if
the message will not be used by the kernel, in which case we can
free the virq.
In addition to elimiating inefficient code, this also corrects the
error that a kernel built with kexec but without a debugger would
not register the ipi for kdump to notify the other cpus of a crash.
This also restores the debugger action to be static to kernel/smp.c.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Compile the new smp ipi mux and demux code only if a platform
will make use of it. The new config is selected as required.
The new cause_ipi smp op is only available conditionally to point out
configs where the select is required; this makes setting the op an
immediate fail instead of a deferred unresolved symbol at link.
This also creates a new config for power surge powermac upgrade support
that can be disabled in expert mode but is default on.
I also removed the depends / default y on CONFIG_XICS since it is selected
by PSERIES.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Consolidate the mux and demux of ipi messages into smp.c and call
a new smp_ops callback to actually trigger the ipi.
The powerpc architecture code is optimised for having 4 distinct
ipi triggers, which are mapped to 4 distinct messages (ipi many, ipi
single, scheduler ipi, and enter debugger). However, several interrupt
controllers only provide a single software triggered interrupt that
can be delivered to each cpu. To resolve this limitation, each smp_ops
implementation created a per-cpu variable that is manipulated with atomic
bitops. Since these lines will be contended they are optimialy marked as
shared_aligned and take a full cache line for each cpu. Distro kernels
may have 2 or 3 of these in their config, each taking per-cpu space
even though at most one will be in use.
This consolidation removes smp_message_recv and replaces the single call
actions cases with direct calls from the common message recognition loop.
The complicated debugger ipi case with its muxed crash handling code is
moved to debug_ipi_action which is now called from the demux code (instead
of the multi-message action calling smp_message_recv).
I put a call to reschedule_action to increase the likelyhood of correctly
merging the anticipated scheduler_ipi() hook coming from the scheduler
tree; that single required call can be inlined later.
The actual message decode is a copy of the old pseries xics code with its
memory barriers and cache line spacing, augmented with a per-cpu unsigned
long based on the book-e doorbell code. The optional data is set via a
callback from the implementation and is passed to the new cause-ipi hook
along with the logical cpu number. While currently only the doorbell
implemntation uses this data it should be almost zero cost to retrieve and
pass it -- it adds a single register load for the argument from the same
cache line to which we just completed a store and the register is dead
on return from the call. I extended the data element from unsigned int
to unsigned long in case some other code wanted to associate a pointer.
The doorbell check_self is replaced by a call to smp_muxed_ipi_resend,
conditioned on the CPU_DBELL feature. The ifdef guard could be relaxed
to CONFIG_SMP but I left it with BOOKE for now.
Also, the doorbell interrupt vector for book-e was not calling irq_enter
and irq_exit, which throws off cpu accounting and causes code to not
realize it is running in interrupt context. Add the missing calls.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I can't see any reason these functions are needed by machdep.h
and they are all hidden by CONFIG_SMP with no UP alternative.
Also move the declarations for the fallback timebase ops, which
are used to fill in the smp ops.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The only user of MSG_ALL_BUT_SELF in the whole kernel tree is powerpc,
and it only uses it to start the debugger. Both debuggers always call
smp_send_debugger_break with MSG_ALL_BUT_SELF, and only mpic can do
anything more optimal than a loop over all online cpus, but all message
passing implementations have to code for this special delivery target.
Convert smp_send_debugger_break to take void and loop calling the smp_ops
message_pass function for each of the other cpus in the online cpumask.
Use raw_smp_processor_id() because we are either entering the debugger
or trying to start kdump and the additional warning it not useful were
it to trigger.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we start a cpu we use smp_ops->kick_cpu(), which currently
returns void, it should be able to fail. Convert it to return
int, and update all uses.
Convert all the current error cases to return -ENOENT, which is
what would eventually be returned by __cpu_up() currently when
it doesn't detect the cpu as coming up in time.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need to wait a bit for them to have done their CPU setup
or we might end up with translation and EE on with different
LPCR values between threads
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Instead, keep it static, expose an accessor and use that from
the PowerMac code. Avoids easy namespace collisions and will
make it easier to consolidate with other implementations.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use generic cpu_state, call idle_task_exit() properly, and
remove smp_core99_cpu_die() which isn't useful, the generic
function does the job just fine.
Various thing are torn down when a CPU is hot-unplugged. That CPU
is expected to go back to start_secondary when re-plugged to re
initialize everything, such as clock sources, maps, ...
Some implementations just return from cpu_die() callback
in the idle loop when the CPU is "re-plugged". This is not enough.
We fix it using a little asm trampoline which resets the stack
and calls back into start_secondary as if we were all fresh from
boot. The trampoline already existed on ppc64, but we add it for
ppc32
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Dynamically allocate cpu_sibling_map and cpu_core_map cpumasks.
We don't need to set_cpu_online() the boot cpu in smp_prepare_boot_cpu,
init/main.c does it for us.
We also postpone setting of the boot cpu in cpu_sibling_map and cpu_core_map
until when the memory allocator is available (smp_prepare_cpus), similar
to x86.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use new cpumask_* functions, and dynamically allocate cpumask in fixup_irqs.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch updates percpu related symbols in powerpc such that percpu
symbols are unique and don't clash with local symbols. This serves
two purposes of decreasing the possibility of global percpu symbol
collision and allowing dropping per_cpu__ prefix from percpu symbols.
* arch/powerpc/kernel/perf_callchain.c: s/callchain/cpu_perf_callchain/
* arch/powerpc/kernel/setup-common.c: s/pvr/cpu_pvr/
* arch/powerpc/platforms/pseries/dtl.c: s/dtl/cpu_dtl/
* arch/powerpc/platforms/cell/interrupt.c: s/iic/cpu_iic/
Partly based on Rusty Russell's "alloc_percpu: rename percpu vars
which cause name clashes" patch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@ozlabs.org
We're weaning the core code off handing cpumask's around on-stack.
This introduces arch_send_call_function_ipi_mask(), and by defining
it, the old arch_send_call_function_ipi is defined by the core code.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This contains all the bits that didn't fit in previous patches :-) This
includes the actual exception handlers assembly, the changes to the
kernel entry, other misc bits and wiring it all up in Kconfig.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Those definitions are currently declared extern in the .c file where
they are used, move them to a header file instead.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With the new generic smp call function helpers, I noticed the code in
smp_message_recv was a single function call in many cases. While
getting the message number from the ipi data is easy, we can reduce
the path length by a function and data-dependent switch by registering
seperate IPI actions for these simple calls.
Originally I left the ipi action array exposed, but then I realized the
registration code should be common too.
The three users each had their own name array, so I made a fourth
to convert all users to use a common one.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Previously the FDT header field boot_cpuid_phys wasn't actually used
on ppc32. Instead the physical boot cpuid was assumed to be 0 for
!CONFIG_SMP.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
They don't need to be macros, and having them as inline functions
avoids warnings about unused variables on some configurations when the
argument isn't evaluated.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
from include/asm-powerpc. This is the result of a
mkdir arch/powerpc/include/asm
git mv include/asm-powerpc/* arch/powerpc/include/asm
Followed by a few documentation/comment fixups and a couple of places
where <asm-powepc/...> was being used explicitly. Of the latter only
one was outside the arch code and it is a driver only built for powerpc.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Alexander Graf