Zen Kato has a device which reports the 0xa RF type. The vendor driver
treats this as AL2230S, the same as devices with the AL2230S bit in the POD.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The vendor driver code suggests that CR47 patching happens on every channel
change for every RF (depending on bit 8 in POD).
Due to a bug in their driver (upper bits of RF_Mode get zeroed out, then
are examined for 1s when setting some other flags), this isn't actually
what happens, and their generic CCK patching routine never takes effect.
Some of their RF configurations do include explicit (duplicated) code
for CR47 patching though. This patch makes zd1211rw match that
behaviour.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for another radio appearing in new devices: the
Ubec UW2453. It's more complicated than the other RF's we support, but
Ubec publish full tech specs so we're able to understand the vendor code
relatively well.
Now that we support UW2453, we also support Atheros' new USB chip: the
AR5007UG. From the little info we have, this appears to be just a
rebranded ZD1211B.
This RF code doesn't work very well -- lots more TX/RX errors than the
other RFs. However, the vendor driver doesn't do any better, so this is
all we can do for now.
[kune@deine-taler.de: bug fixes]
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These changes are needed for UW2453 RF support:
Add pointer which RF drivers can use to store private RF data
Add exit hook so that RF drivers can free private data
Allow RF's to disable the generic TX power integration handling code
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This change allows RF drivers to provide their own 6M band edge patching
implementation, while providing a generic implementation shared by most
currently supported RF's.
The upcoming ZD1211B/AL7230B code will use this to define its own
patching function, which is different from the other RF configurations.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ZD1211 appears to be back in production: a number of new devices have
been appearing! Some of them are using new radios.
This patch adds support for the next generation AL2230 RF chip which has
been spotted in a few new devices.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of passing our own custom 32-bit addresses around and
translating them, this patch makes all our register address constants
absolute and removes the translation.
There are two ugly parts:
- fw_reg_addr() is needed to compute addresses of firmware registers, as this
is dynamic based upon firmware
- inc_addr() needs a small hack to handle byte vs word addressing
However, both of those are only small, and we don't use fw_regs a whole
lot anyway.
The bonuses here include simplicity and improved driver readability. Also, the
fact that registers are now referenced by 16-bit absolute addresses (as
opposed to 32-bit pseudo addresses) means that over 2kb compiled code size has
been shaved off.
Includes some touchups and sparse fixes from Ulrich Kunitz.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for another Airoha RF which is present in some
ZD1211 adapters. This RF supports 802.11a as well as 802.11b/g, but 802.11a
connectivity is not yet supported by this driver.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are 60+ USB wifi adapters available on the market based on the ZyDAS
ZD1211 chip.
Unlike the predecessor (ZD1201), ZD1211 does not have a hardware MAC, so most
data operations are coordinated by the device driver. The ZD1211 chip sits
alongside an RF transceiver which is also controlled by the driver. Our driver
currently supports 2 RF types, we know of one other available in a few marketed
products which we will be supporting soon.
Our driver also supports the newer revision of ZD1211, called ZD1211B. The
initialization and RF operations are slightly different for the new revision,
but the main difference is 802.11e support. Our driver does not support the
QoS features yet, but we think we know how to use them.
This driver is based on ZyDAS's own GPL driver available from www.zydas.com.tw.
ZyDAS engineers have been responsive and supportive of our efforts, so thumbs
up to them. Additionally, the firmware is redistributable and they have
provided device specs.
This driver has been written primarily by Ulrich Kunitz and myself. Graham
Gower, Greg KH, Remco and Bryan Rittmeyer have also contributed. The
developers of ieee80211 and softmac have made our lives so much easier- thanks!
We maintain a small info-page: http://zd1211.ath.cx/wiki/DriverRewrite
If there is enough time for review, we would like to aim for inclusion in
2.6.18. The driver works nicely as a STA, and can connect to both open and
encrypted networks (we are using software-based encryption for now). We will
work towards supporting more advanced features in the future (ad-hoc, master
mode, 802.11a, ...).
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Daniel Drake